SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z & ANSI/NCSL Z

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z & ANSI/NCSL Z SIMCO ELECTRONICS 6295 Ferris Square San Diego, CA Jeremy Cooper Phone: CALIBRATION Valid To: September 30, 2018 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following calibrations and dimensional inspections 1 : I. Dimensional Parameter/Equipment Range 4 CMC 2, 7 ( ) Comments Calipers 3 Up to 5 in (5 to 48) in ( L) µin ( L) µin Gage blocks Micrometers 3 Flatness Parallelism <0.001 in <0.001 in 12 µin 18 µin Optical parallels, & monochromatic light Linearity Up to 1 in (1 to 4) in (4 to 48) in ( L) µin + 0.6R (15 + 4L) µin + 0.6R (68 + 4L) µin + 0.6R Gage blocks Height Gages 3 Up to 5 in (5 to 36) in ( L) µin (80 + 6L) µin Gage blocks, surface plates Depth Gages 3 Linearity Up to 5 in (5 to 36) in ( L) µin + 0.6R (80 + 6L) µin + 0.6R Gage blocks, surface plates Flatness <0.001 in 11 µin Optical parallels, & monochromatic light (A2LA Cert. No ) 08/29/2016 Page 1 of 21

2 Parameter/Equipment Range 4 CMC 2, 7 ( ) Comments Pin, Plug Gages Up to 1 in ( L) µin Supermicrometer, gage blocks Digital & Dial Up to 2 in ( L) µin + 0.6R Gage blocks & surface Indicators 3 plates End Standards Up to 5 in (5 to 10) in ( L) µin ( L) µin Gage blocks, Supermicrometer Surface Plates 3 Flatness Up to 48 x 72 in 98 µin Planekator Repeatability Up to in 28 µin Repeat-o-meter Thread Plug Gages Pitch Diameter Major Diameter Up to 1 in (1 to 4) in Up to 1 in (1 to 4) in ( L) µin ( L) µin ( L) µin ( L) µin Supermicrometer, gage blocks and thread wires II. Electrical DC/Low Frequency Parameter/Equipment Range 4 CMC 2, 8 ( ) Comments DC Voltage Generate 3 (0 to 220) mv (0.22 to 2.2) V (2.2 to 11) V (11 to 22) V (22 to 220) V (220 to 1100) V 10 µv/v µv 7.4 µv/v + 1 µv 7.2 µv/v µv 7.3 µv/v µv 8.4 µv/v + 80 µv 12 µv/v µv Fluke 5700A/5725A (A2LA Cert. No ) 08/29/2016 Page 2 of 21

3 Parameter/Equipment Range 4 CMC 2, 5, 6, 8, 9 ( ) Comments DC Voltage Measure 3 (0 to 100) mv (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V* 8.5 V/V V 6.0 V/V V 5.3 V/V + 1 V 10 V/V + 80 V 13 V/V V* Agilent 3458A OPT-2 *add 12(V in /1000) 2 Parts in 10 6 to all V in >100 (1000 to ) V ( to ) V 0.13 % 0.16 % Ross VD A-KB-AL & HP 34401A DC Current Generate 3 (20 to 220) µa (0.22 to 2.2) ma (2.2 to 22) ma (22 to 220) ma (0.22 to 2.2) A (2.2 to 11) A 54 µa/a + 8 na 52 µa/a + 8 na 52 µa/a na 62 µa/a µa 85 µa/a + 25 µa % µa Fluke 5700A/5725A (11 to 20.5) A % µa Fluke 5520A/SC600 Clamp Meters to 1000 A (10 to 100) A (20.5 to 1000) A 0.1 % 0.51 % A Valhalla 2555A, L&N 4361, & Agilent 3458A Fluke 5500A/coil and 5520A/SC600 DC Current Measure 3 (0.1 to 1) µa (1 to 10) µa (10 to 100) µa (0.1 to 1) ma (1 to 10) ma (10 to 100) ma (0.1 to 1) A (1 to 10) A (10 to 100) A 36 µa/a + 70 pa 24 µa/a pa 23 µa/a na 22 µa/a + 5 na 22 µa/a + 50 na 36 µa/a µa 0.01 % + 10 µa 0.06 % 0.1 % Agilent 3458A OPT-2 L&N 4361 and Agilent 3458A opt-2 (A2LA Cert. No ) 08/29/2016 Page 3 of 21

4 Parameter/Equipment Range CMC 2, 6, 8, 9 ( ) Comments Resistance Measure 3 (0 to 10) Ω (10 to 100) Ω (0.1 to 1) kω (1 to 10) kω (10 to 100) kω (0.1 to 1) MΩ (1 to 10) MΩ (10 to 100) MΩ (0.1 to 1.0) GΩ 15 µω/ω + 52 µω 12 µω/ω mω 10 µω/ω mω 10 µω/ω mω 10 µω/ω + 58 mω 15 µω/ω + 2 Ω 52 µω/ω Ω % + 1 kω 0.51 % + 11 kω Agilent 3458A OPT-2 Resistance Generate 3 Fixed Points 0 Ω 1 Ω 1.9 Ω 10 Ω 19 Ω 100 Ω 190 Ω 1 kω 1.9 kω 10 kω 19 kω 100 kω 190 kω 1 MΩ 1.9 MΩ 10 MΩ 19 MΩ 100 MΩ 51 µω 98 µω/ω µω 98 µω/ω µω 30 µω/ω µω 29 µω/ω µω 18 µω/ω µω 18 µω/ω + 82 µω 14 µω/ω + 82 µω 14 µω/ω µω 13 µω/ω µω 13 µω/ω mω 13 µω/ω mω 15 µω/ω + 82 mω 21 µω/ω + 82 mω 22 µω/ω mω 47 µω/ω mω 53 µω/ω Ω % Ω Fluke 5700A (A2LA Cert. No ) 08/29/2016 Page 4 of 21

5 Parameter/Equipment Range CMC 2, 5, 9 ( ) Comments Resistance Generate 3 (cont) 4-Wire BNC 0.1 Ω 1 Ω 10 Ω 100 Ω 1 kω 10 kω 100 kω 3.4 % 3.3 % 5.1 % 3.4 % 0.04 % 0.17 % 1.4 % HP 16074A Variable (0 to 11) Ω (11 to 33) Ω (33 to 110) Ω (110 to 330) Ω (0.33 to 1.1) kω (1.1 to 3.3) kω (3.3 to 11) kω (11 to 33) kω (33 to 110) kω (110 to 330) kω (0.33 to 1.1) MΩ (1.1 to 3.3) MΩ (3.3 to 11) MΩ (11 to 33) MΩ (33 to 110) MΩ (110 to 330) MΩ (0.33 to 1.1) GΩ 32 µω/ω mω 24 µω/ω mω 22 µω/ω mω 22 µω/ω mω 22 µω/ω mω 22 µω/ω + 16 mω 22 µω/ω + 17 mω 22 µω/ω mω 22 µω/ω mω 28 µω/ω Ω 28 µω/ω Ω 52 µω/ω + 24 Ω % + 39 Ω % kω % kω 0.24 % + 78 kω 1.2 % kω Fluke 5520A/SC600 (A2LA Cert. No ) 08/29/2016 Page 5 of 21

6 Parameter/Equipment Range CMC 2, 9 ( ) Comments Electrical Simulation of Thermocouples Indicating Devices Generate & Measure 3 Type E -250 C to -100 C -100 C to -25 C -25 C to 350 C 350 C to 650 C 650 C to 1000 C 0.39 C 0.14 C 0.12 C 0.14 C 0.17 C Fluke 5520A/SC600 Type J -210 C to -100 C -100 C to -30 C -30 C to 150 C 150 C to 760 C 760 C to 1200 C 0.22 C 0.14 C 0.12 C 0.14 C 0.19 C Type K -200 C to -100 C -100 C to -25 C -25 C to 120 C 120 C to 1000 C 1000 C to 1372 C 0.27 C 0.16 C 0.14 C 0.21 C 0.32 C Type T -250 C to -150 C -150 C to 0 C 0 C to 120 C 120 C to 400 C 0.50 C 0.20 C 0.14 C 0.12 C Waveform Measure 3 Amplitude (0 to 40) V Time / Frequency DC to 1 GHz DC to 1 GHz 1.7 % 120 µhz/hz Tektronix TDS684C Rise & Fall Time 350 ps to 1 s 57 ps (A2LA Cert. No ) 08/29/2016 Page 6 of 21

7 Parameter/Range 4 Frequency CMC 2, 5, 6, 9 ( ) Comments Oscilloscopes 3 Level Sine Wave (5 mv to 5.5 V) (p-p) Level Sine Flatness (5 mv to 5.5 V) (p-p) Relative to 50 khz Reference DC Signal 50, (0.01 to 10) khz 1 M, (0.01 to 10) khz 50 khz reference (0.05 to 100) MHz (100 to 300) MHz (300 to 600) MHz 1 mv to 6.6 V 1 mv to 130 V 1.6 % V 1.7 % V 2 % V 3.3 % V 0.2 % + 40 V 0.08 % + 40 V Fluke 5520A/SC600 See RF Power/Flatness generate for oscilloscopes above 600 MHz Square Wave Signal 50, (0.01 to 10) khz 1 M, (1 to 10) khz 1 mv to 6.6 V (p-p) 1 mv to 130 V (p-p) 0.2 % + 40 V 0.08 % + 40 V Time Marker Output Into 50 2 ns to 20 ms 50 ms to 5 s 2.1 µs/s ( t) µs/s t = sec Pulse Rise Time Generate Rep Rate: 1 khz to 10 MHz (125 to 350) ps 40 ps AC Current Measure 3 (5 to 100) µa (0.1 to 1) ma (45 to 1000) Hz (45 to 100) Hz (0.1 to 5) khz % + 35 na 0.07 % na % na Agilent 3458A OPT -2 (1 to 10) ma (45 to 100) Hz (0.1 to 5) khz 0.07 % µa % µa (10 to 100) ma (45 to 100) Hz (0.1 to 5) khz 0.07 % + 23 µa % + 23 µa (0.1 to 1) A (45 to 100) Hz (0.1 to 5) khz % µa 0.12 % µa (1 to 10) A (10 to 100) A (10 to 60) Hz (10 to 60) Hz % 0.15 % L & N 4361 & Agilent 3458A (A2LA Cert. No ) 08/29/2016 Page 7 of 21

8 Parameter/Range Frequency CMC 2, 5, 8, 9 ( ) Comments AC Current Generate 3 (0.22 to 2.2) ma (>40 to 1000) Hz (1 to 5) khz % + 35 na % na Fluke 5700A/5725A (2.2 to 22) ma (>40 to 1000) Hz (1 to 5) khz % na % na (22 to 220) ma (>40 to 1000) Hz (1 to 5) khz % µa % + 40 µa (0.22 to 2.2) A (>40 to 1000) Hz (1 to 5) khz % + 35 µa % + 80 µa (2.2 to 11) A (>40 to 1000) Hz (1 to 5) khz (5 to 10) khz 0.05 % µa % µa 0.36 % µa (33 to 330) µa (11 to 20.5) A (>45 to 1000) Hz (1 to 5) khz (>0.1 to 1) khz (1 to 5) khz % µa 0.23 % µa 0.12 % ma 2.3 % ma Fluke 5520A/SC600 LCOMP OFF (10 to 100) A Clamp Meters to 1000 A (20.5 to 1000) A (10 to 60) Hz (45 to 400) Hz 0.15 % 1.5 % A Valhalla 2555A, L&N 4361, & Agilent 3458A Fluke 5500A/coil & 5520A/SC600 LCOMP OFF (A2LA Cert. No ) 08/29/2016 Page 8 of 21

9 Parameter/Range Frequency CMC 2, 8, 9 ( ) Comments AC Voltage Generate 3 (0.22 to 2.2) mv (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 khz (300 to 500) khz (0.5 to 1) MHz % µv % µv % µv % µv % + 9 µv 0.11 % + 16 µv 0.17 % + 29 µv 0.34 % + 31 µv Fluke 5700A OPT 03 & 5725A (2.2 to 22) mv (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 khz (300 to 500) khz (0.5 to 1) MHz % + 11 µv % µv % + 12 µv % + 13 µv % + 14 µv 0.11 % + 27 µv 0.17 % + 40 µv 0.34 % + 55 µv (22 to 220) mv (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 khz (300 to 500) khz (0.5 to 1) MHz % + 53 µv % + 23 µv % + 8 µv % + 8 µv % + 25 µv 0.15 % + 25 µv 0.18 % + 35 µv 0.4 % + 80 µv (0.22 to 2.2) V (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 khz (300 to 500) khz (0.5 to 1) MHz 0.05 % µv 0.16 % µv 83 µv/v + 6 µv % + 16 µv % + 70 µv % µv 0.11 % µv 0.23 % µv (2.2 to 22) V (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 khz (300 to 500) khz (0.5 to 1) MHz 0.05 % mv % mv 83 µv/v + 60 µv % µv % µv 0.05 % mv 0.13 % mv 0.31 % mv (A2LA Cert. No ) 08/29/2016 Page 9 of 21

10 Parameter/Range Frequency CMC 2, 6, 8, 9 ( ) Comments AC Voltage Generate 3 (cont) (22 to 220) V (10 to 20) Hz (20 to 40) Hz 40 Hz to 20 khz (300 to 500) khz (0.5 to 1) MHz 0.05 % + 48 mv % + 17 mv 89 µv/v mv 0.02 % mv 0.05 % + 8 mv 0.15 % + 90 mv 0.47 % + 90 mv 1.2 % mv Fluke 5700A OPT 03 & 5725A Subject to 2.2 x 10 7 V Hz limitation (220 to 1100) V (40 to 1000) Hz (1 to 20) khz (20 to 30) khz 94 µv/v mv % + 6 mv % + 11 mv (250 to 750) V (30 to 50) khz % + 11 mv AC Voltage Measure 3 (1 to 10) mv (1 to 40) Hz (40 to 1000) Hz (1 to 20) khz % µv % µv % µv 0.12 % µv 0.58 % µv 4.6 % µv Agilent 3458A OPT-2 (10 to 100) mv (1 to 40) Hz (40 to 1000) Hz (1 to 20) khz (0.3 to 1) MHz % µv % µv % µv % µv % µv 0.35 % + 12 µv 1.2 % + 12 µv (0.1 to 1) V (1 to 40) Hz (40 to 1000) Hz (1 to 20) khz (0.3 to 1) MHz % + 46 µv % + 23 µv % + 20 µv % + 20 µv % + 23 µv 0.35 % µv 1.2 % µv (1 to 10) V (1 to 40) Hz (40 to 1000) Hz (1 to 20) khz (0.3 to 1) MHz % mv % mv % mv % mv % mv 0.35 % mv 1.2 % mv (A2LA Cert. No ) 08/29/2016 Page 10 of 21

11 Parameter/Range Frequency CMC 2, 6, 9 ( ) Comments AC Voltage Measure 3 (cont) (10 to 100) V (1 to 40) Hz (40 to 1000) Hz (1 to 20) khz % mv % mv % mv % mv 0.14 % mv 0.46 % + 12 mv Agilent 3458A OPT-2 (100 to 700) V (1 to 40) Hz (40 to 1000) Hz (1 to 20) khz % + 46 mv % + 23 mv % + 23 mv 0.14 % + 23 mv 0.35 % + 23 mv (700 to ) V ( to ) V (50 to 60) Hz (50 to 60) Hz 0.59 % 0.61 % Ross VD A- KB-AL & HP 34401A Inductance Generate 3 4-Wire BNC 100 H DC to 1 khz 0.24 % HP 16074A 100 mh DC to 1 khz 0.12 % (A2LA Cert. No ) 08/29/2016 Page 11 of 21

12 Parameter/Range 4 Frequency CMC 2, 5, 9 ( ) Comments Capacitance Generate 3 2-Wire (0.19 to <3.3) nf (3.3 to <11) nf (11 to 110) nf (110 to <330) nf (0.33 to <1.1) µf (1.1 to <3.3) µf (3.3 to <11) µf (11 to <33) µf (33 to <110) µf (110 to <330) µf (0.33 to <1.1) mf (1.1 to <3.3) mf (3.3 to <11) mf (11 to <33) mf (33 to <110) mf (0.01 to 10) khz (0.01 to 1) khz (0.01 to 1) khz (0.01 to 1) khz (10 to 600) khz (10 to 300) khz (10 to 150) Hz (10 to 120) Hz (10 to 80) Hz (10 to 50) Hz (0 to 20) Hz (0 to 6) Hz (0 to 2) Hz (0 to 0.6) Hz (0 to 0.2) Hz 0.58 % + 12 pf 0.29 % + 12 pf 0.29 % pf 0.29 % pf 0.29 % nf 0.29 % nf 0.29 % + 12 nf 0.46 % + 36 nf 0.52 % nf 0.52 % nf 0.52 % µf 0.52 % µf 0.52 % + 12 µf 0.87 % + 35 µf 1.3 % µf Fluke 5520A/SC600 4-Wire BNC 1 pf (10 to 1000) Hz (0.001 to 1) MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz % % % % % % 0.25 % 0.37 % HP 16380A air capacitor set, HP 16381A 10 pf (10 to 1000) Hz (0.001 to 1) MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz % % % % % % % 0.04 % HP 16382A (A2LA Cert. No ) 08/29/2016 Page 12 of 21

13 Parameter/Range 4 Frequency CMC 2, 9 ( ) Comments Capacitance Generate 3 (cont) 4-Wire BNC 100 pf (10 to 1000) Hz (0.001 to 1) MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz % % % % % % 0.06 % 0.07 % HP 16383A 1000 pf (10 to 1000) Hz (0.001 to 1) MHz (1 to 2) MHz (2 to 3) MHz (3 to 4) MHz (4 to 5) MHz (5 to 10) MHz (10 to 13) MHz 0.13 % % 0.04 % % % % 0.19 % 0.28 % HP 16384A III. Electrical RF/Microwave Parameter/Range 4 Frequency CMC 2 ( ) Comments RF Power 3 Generate ( to -4.99) dbm (-5.0 to ) dbm 200 Hz to 80 MHz db 0.13 db HP 3335A (+20 to -100) dbm 9 khz to 3200 MHz (>3200 to 4000) MHz 1.2 db 2.3 db HP 8648D OPT-1E2, 1E5, 1EA (<-100 to -127) dbm (9 to <100) khz (0.1 to 2500) MHz (>2500 to 4000) MHz 3.7 db 1.7 db 3.7 db HP 8648D OPT-1E2, 1E5, 1EA > 10 dbm (9.98 to -9.98) dbm (-10 to ) dbm (-60 to -110) dbm (0.01 to <2) GHz 1.4 db 0.72 db 1.0 db 1.6 db HP 83640B OPT-001 Band 0 > 10 dbm (9.98 to -9.98) dbm (-10 to ) dbm (-60 to -110) dbm (2 to 20) GHz 1.5 db 0.88 db 1.2 db 1.8 db HP 83640B OPT-001 Bands 1, 2, & 3 (A2LA Cert. No ) 08/29/2016 Page 13 of 21

14 Parameter/Range 4 Frequency CMC 2 ( ) Comments RF Power 3 Generate (cont) (9.98 to -9.98) dbm (-10 to ) dbm (-60 to -110) dbm (20 to 40) GHz 1.1 db 1.4 db 2 db HP 83640B OPT-001 Bands 4, 5 & 6 RF Flatness 3 Generate (+13 to ) dbm 1 khz to 25 MHz (25 to 80) MHz db 0.18 db HP 3335A > 10 dbm (9.98 to -9.98) dbm (-10 to ) dbm (-60 to -110) dbm (0.01 to <2) GHz 1.1 db 0.63 db 0.84 db 1.3 db HP 83640B OPT-001 Band 0 > 10 dbm (9.98 to -9.98) dbm (-10 to ) dbm (-60 to -110) dbm (2 to 20) GHz 1.2 db 0.76 db 0.98 db 1.4 db HP 83640B OPT-001 Bands 1, 2 & 3 (9.98 to -9.98) dbm (-10 to ) dbm (-60 to -110) dbm (20 to 40) GHz 0.98 db 1.2 db 1.6 db HP 83640B OPT-001 Bands 4, 5 & 6 RF Power/Flatness 3 Generate (+20 to -20) dbm (0.3 to 1) MHz (0.001 to 4.2) GHz 0.2 db 0.19 db 0.19 db HP 8648D, 11667B, 8482A & E4419B (+20 to -50) dbm (0.05 to 10) GHz (10 to 13) GHz (13 to 26.5) GHz 0.2 db 0.25 db 0.32 db HP 83640B, 11667B, E4413A & E4419B (A2LA Cert. No ) 08/29/2016 Page 14 of 21

15 Parameter/Range 4 Frequency CMC 2, 9 ( ) Comments RF Power 3 Measure (+10 to 0) dbm (0 to -10) dbm (-10 to -20) dbm (-20 to -30 dbm (-30 to -40) dbm (-40 to -50) dbm (-50 to -60) dbm (-60 to -70) dbm (-70 to -80) dbm (-80 to -90) dbm (-90 to -100) dbm (-100 to -110) dbm (-110 to -120) dbm 2.5 MHz to 1.3 GHz 0.11 db 0.11 db 0.11 db 0.12 db 0.15 db 0.16 db 0.18 db 0.21 db 0.24 db 0.25 db 0.27 db 0.29 db 0.52 db HP 8902A & 11722A (+10 to 0) dbm (<0 to -10) dbm (<-10 to -20) dbm (<-20 to -30) dbm (<-30 to -40) dbm (<-40 to -50) dbm (<-50 to -60) dbm (<-60 to -70) dbm (<-70 to -80) dbm (<-80 to -90) dbm (<-90 to -100) dbm (1.3 to 26.5) GHz 0.10 db 0.11 db 0.11 db 0.13 db 0.15 db 0.16 db 0.18 db 0.21 db 0.23 db 0.25 db 0.27 db HP 8902A & 11792A 0 dbm 50 MHz (0.01 to 1) GHz db (0.44 %) db (0.57 %) HP 432A, 478A-H75, 34401A (+20 to -20) dbm (0.3 to 1) MHz (0.001 to 4.2) GHz db db db HP 8482A & E4419B (+20 to -50) dbm (0.05 to 10) GHz (10 to 13) GHz (13 to 26.5) GHz db db 0.12 db HP E4413A & E4419B (30 to -90) dbm 9 khz to 2.9 GHz (2.9 to 6.46) GHz (6.46 to 13.2) GHz (13.2 to 22) GHz (22 to 26.8) GHz (26.8 to 31.15) GHz 1.2 db 2.1 db 3.2 db 4.1 db 4.6 db 3.5 db HP 8564E (30 to -90) dbm (31.15 to 40) GHz 3.7 db (A2LA Cert. No ) 08/29/2016 Page 15 of 21

16 Parameter/Range 4 Frequency CMC 2 ( ) Comments RF Attenuation 3 Measure (0 to -10) db (-10 to -20) db (-20 to -30) db (-30 to -40) db (-40 to -50) db (-50 to -60) db (-60 to -70) db (-70 to -80) db (-80 to -90) db (-90 to -100) db (-100 to -110) db 2.5 MHz to 1.3 GHz db db db db 0.12 db 0.14 db 0.16 db 0.20 db 0.22 db 0.24 db 0.33 db HP 8902A & 11722A (0 to -10) db (-10 to -20) db (-20 to -30) db (-30 to -40) db (-40 to -50) db (-50 to -60) db (-60 to -70) db (-70 to -80) db (-80 to -90) db (-90 to -100) db (1.3 to 26.5) GHz db db db 0.10 db 0.13 db 0.15 db 0.17 db 0.20 db 0.23 db 0.33 db HP 8902A & 11792A (0 to -25) db (0.3 to 1) MHz (0.001 to 4.2) GHz db db db HP 8482A & E4419B (0 to -50) db (0.05 to 10) GHz (10 to 13) GHz (13 to 26.5) GHz db db db HP E4413A & E4419B (0 to -120) db 9 khz to 2.9 GHz (2.9 to 6.46) GHz (6.46 to 13.2) GHz (13.2 to 22) GHz (22 to 26.8) GHz (26.8 to 31.15) GHz 0.93 db 1.6 db 2.5 db 2.9 db 2.5 db 3.4 db HP 8564E (0 to -115) db (31.15 to 40) GHz 2.8 db (A2LA Cert. No ) 08/29/2016 Page 16 of 21

17 Parameter/Range Frequency CMC 2, 7, 9 ( ) Comments Distortion 3 Measure -80 db -65 db 20 Hz to 20 khz (20 to 100) khz 1.2 db 2.3 db HP 8903B Amplitude Modulation 3 Measure Depth: (5 to 99) % Rate: (0.05 to 10) khz Depth: (5 to 99) % Rate: (0.02 to 10) khz (0.15 to 10) MHz 2.1 % + 1.0R 3.0 % + 1.0R HP 8902A & 11722A Depth: (5 to 99) % Rate: (0.05 to 50) khz Depth: (5 to 99) % Rate: (0.02 to 100) khz (0.01 to 1.3) GHz 1.1 % + 1.0R 3.0 % + 1.0R Depth: (5 to 99) % Rate: (0.05 to 50) khz Depth: (5 to 99) % Rate: (0.02 to 100) khz (1.3 to 26.5) GHz 1.6 % + 1.0R 3.0 % + 1.0R HP 8902 & 11792A Frequency Modulation 3 Measure Deviation: <40 khz/pk Rate: (0.02 to 10) khz (0.25 to 10) MHz 2.3 % + 1.3R HP 8902A & 11722A Deviation: <400 khz/pk Rate: (0.05 to 100) khz (0.01 to 26.5) GHz 1.2 % + 1.3R HP8902A, 11772A & 11792A Deviation: <400 khz/pk Rate: (0.05 to 200) khz (0.01 to 26.5) GHz 5.8 % + 1.3R Phase Modulation 3 Measure Rate: (0.2 to 10) khz (0.15 to 10) MHz 4 % Rad HP 8902A & 11722A Rate: (0.02 to 200) khz (0.01 to 26.5) GHz 5 % Rad HP 8902A & 11792A (A2LA Cert. No ) 08/29/2016 Page 17 of 21

18 IV. Mechanical Parameter/Equipment Range CMC 2, 7, 9 ( ) Comments Scales & Balances 3 (1 to 500) mg (1 to 5) g (5 to 10) g (10 to 20) g (20 to 200) g (0.2 to 10) kg (10 to 20) kg (20 to 35) kg mg R mg R mg R mg R % R % R 84 mg R 89 mg R Troemner Ultra Class & Class 1 weights (0 to 500) lb % R Class F weights Torque Measure (5 to 50) in ozf (1 to 10) in lbf (10 to 50) in lbf (50 to 250) in lbf (25 to 250) ft lbf (250 to 500) ft lbf (500 to 1000) ft lbf 0.75 % R 0.6 % R 0.65 % R 0.61 % R 0.71 % R 0.72 % R 5.8 ft lbf R AWS torque system Mountz torque system Torque Measure 3 (5 to 50) in ozf (1 to 10) in lbf (10 to 50) in lbf (50 to 250) in lbf 0.75 % R 0.6 % R 0.65 % R 0.61 % R AWS torque system Mountz torque system Torque Measuring (0 to 250) in lbf 0.12 % R Class F weights & Equipment 3 torque wheels Force 3 Measuring Equipment (0 to 300) lbf % R Class F weights Pressure & Vacuum Measuring Equipment & Measure (0.9 to 3.16) psia (3.16 to 7.53) psia (7.53 to 23) psia (23 to 97) psia (97 to 300) psia psia R % R % R psia R 0.01 % R Fluke PPC4 (-14.7 to -12.3) psig (-12.3 to -7.9) psig (-7.9 to 8) psig (8 to 86.7) psig (86.7 to 300) psig psig R % R % R psig R % R (2 to ) psi % R Pressurements M P (A2LA Cert. No ) 08/29/2016 Page 18 of 21

19 Parameter/Equipment Range CMC 2, 7, 9 ( ) Comments Pressure & Vacuum Measuring Equipment & Measure 3 (-14.7 to 300) psig (300 to 1000) psig (1000 to ) psig 0.18 psig R 1.2 psig R 7.3 psig R Druck PM620 Druck DPI705 RPM Measure 3 (0 to ) rpm % R Monarch PLT200 V. Thermodynamic Parameter/Equipment Range CMC 2, 7, 9 ( ) Comments Temperature Measuring Equipment (-70 to 175) o C o C R Hart Scientific 1502A, 5628 w/temperature sources Temperature Measuring Equipment 3 (-5 to 125) o C (-15 to 350) o C o C R 0.12 o C R Hart Scientific 1502A, 5628 w/temperature sources Temperature Measure 3 (-196 to 0) o C (0 to 100) o C (100 to 350) o C (350 to 660) o C o C R o C R o C R o C R Hart Scientific 1502A, 5628 Infrared Temperature Measuring Equipment 3, 10 (25 to 100) o C (100 to 300) o C (300 to 500) o C 0.61 o C % 0.78 o C % 1 o C % Hart Scientific 9132 λ = (8 to 14) µm Ɛ = 0.95 Relative Humidity Measure & Measuring Equipment 3 (1 to 90) % RH (90 to 99) % RH 1.4 % RH 2.3 % RH Vaisala HMI41/HPM46, MI70/HMP76 w/humidity chamber (A2LA Cert. No ) 08/29/2016 Page 19 of 21

20 VI. Time & Frequency Parameter/Range Frequency CMC 2 ( ) Comments Timers & Stopwatches 3 Up to 24 hours 65 ms HP 53132A, HP 33220A phase locked to GPS Frequency Reference 10 MHz 1.7 phz/hz Fluke 910R GPS Frequency Measuring Equipment Hz to 600 MHz 86 phz/hz + 5 µhz Fluke 5520A phase locked to GPS 9 khz to 4 GHz 86 phz/hz HP 8648D phase locked to GPS (0.01 to 40) GHz 86 phz/hz HP 83640B phase locked to GPS Frequency 3 Measure 0.1 Hz to 3 GHz 86 phz/hz + 5 µhz Fluke GPS & HP 53132A phase locked to GPS 10 Hz to 26.5 GHz 0.58 nhz/hz Fluke GPS & HP 5343A phase locked to GPS (26.5 to 40) GHz 1.1 nhz/hz Fluke GPS & HP 8564E phase locked to GPS Tachometers (60 to ) rpm 0.18 mrpm/rpm R HP 33220A phase locked to GPS 1 This laboratory offers commercial calibration service and field calibration service. 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific calibration. 3 Field calibration service is available for this calibration and this laboratory meets A2LA R104 General Requirements: Accreditation of Field Testing and Field Calibration Laboratories for these calibrations. Please note the actual measurement uncertainties achievable on a customer's site can normally be expected to be larger than the CMC found on the A2LA Scope. Allowance must be made for aspects such as the environment at the place of calibration and for other possible adverse effects such as those caused by transportation of the calibration equipment. The usual allowance for the actual uncertainty introduced by the item being calibrated, (e.g. resolution) must also be considered and this, on its own, could result in the actual measurement uncertainty achievable on a customer s site being larger than the CMC. (A2LA Cert. No ) 08/29/2016 Page 20 of 21

21 4 Where ranges are not specified, the CMC stated is for the cardinal points only. Other values can be obtained using substitution method with uncertainty increased by a multiple for each substitution. 5 Based on using the standard at the temperature the Fluke 5520A with SC600 was calibrated (tcal ± 5 o C) and assuming the instrument is zeroed at least every seven days or when the ambient temperature changes more than 5 o C. For resistance, a zero calibration is performed at least every 12 hours within ± 1 o C of use. For AC Current, CMC are determined with LCOMP Off. CMC is based upon 1-year specifications and is read as ppm (parts per million) or percent output plus floor specification where defined. 6 Based on using the standard at the temperature the Agilent 3458A was calibrated (tcal ± 5 o C) and an auto-calibration (ACAL) was performed within the previous 24 hours (± 1 o C of ambient temperature). CMC is based upon 1-year specifications and is read as ppm (parts per million) or percent output plus floor specification where defined. 7 In the statement of CMC, L is the numerical value of the nominal length of the device measured in inches; R is the numerical value of the resolution of the device. 8 Based on using the Fluke 5700A/5725A within 5 o C of the temperature noted at the time of cal (tcal ± 5 o C) and assuming the zero calibration is performed every 30 days. CMC is based upon 1-year specifications and is read as ppm (parts per million, V/V) or percent of output plus floor specification where defined. Includes stability. Resistance specifications apply only to the displayed resistance value using 4-wire configuration (except for 100 MΩ). Uncertainty specifications for 220 ma and 2.2 ma ranges are increased by a factor of 1.3 when supplied through 5725A terminals. 9 When percent (%) is present in the statement of CMC; the value is defined as the percentage of reading unless otherwise noted. 10 Target Emissivity is not calibrated and assumed to be 0.95 (±0.02 from 8 to 14 µm) for Blackbody. (A2LA Cert. No ) 08/29/2016 Page 21 of 21

22 Accredited Laboratory A2LA has accredited SIMCO ELECTRONICS San Diego, CA for technical competence in the field of Calibration This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This laboratory also meets the requirements of ANSI/NCSLI Z and the requirements of ANSI/NCSLI Z and R205 Specific Requirements Calibration Laboratory Accreditation Program. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 29 th day of August Senior Director of Quality and Communications For the Accreditation Council Certificate Number Valid to September 30, 2018 For the calibrations to which this accreditation applies, please refer to the laboratory s Calibration Scope of Accreditation.