SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z & ANSI/NCSL Z540.3

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 & ANSI/NCSL Z & ANSI/NCSL Z540.3 SIMCO ELECTRONICS Nordhoff Place Chatsworth, CA Randy Ford Phone: CALIBRATION Valid To: September 30, 2017 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following calibrations and dimensional inspections 1 : I. Dimensional Parameter/Equipment Range 4 CMC 2, 5 ( ) Comments Gage Blocks (0.01 to 0.09) in (0.1 to 4) in ( L) µin ( L) µin Federal 130B-24 gage block comparator (0.5 to 100) mm (40 + 8L) µm Angle Sine Plates & Angle Blocks Up to 15 in 69 µin Gage blocks, MU-checker, angle gage blocks Protractors & Inclinometers Up to 180 0, 00, 1.2 Angle block set Optical Flat Flatness 3.7 µin Van Keuren 4 inch optical flat, gage blocks Length Standards (1 to 60) in ( L) µin SIP MUL 4000, laser, gage blocks Micrometers 3 Up to 48 in ( L) µin Gage blocks (A2LA Cert. No ) 10/09/2015 Page 1 of 24

2 Parameter/Equipment Range CMC 2, 5 ( ) Comments Height Gages 3 Up to 40 in (30 + 7L) µin Gage blocks Depth Gages 3 Up to 12 in (30 + 7L) µin Gage blocks Calipers 3 Up to 5 in (5 to 48) in (48 to 72) in ( L) µin ( L) µin ( L) µin Gage blocks Indicators 3 Up to 6 in ( L) µin Gage blocks Tapes & Rules Up to 60 in ( L) µin SIP MUL 4000, Agilent laser head Glass Scales Up to 24 in ( L) µin SIP MUL 4000, gage blocks, Agilent laser head Plain Ring Gages (0.025 to 1) in (>1 to 4) in 14 in ( L) µin Gage blocks, Pratt & Whitney Universal Supermic TM Pin Gages Up to 4 in 15 in Pratt & Whitney Universal Supermic TM, gage blocks Thread Plug Gages Major Diameter Pitch Diameter Up to 4 in Up to 80 TPI ( ) in ( L) in Pratt & Whitney Universal Supermic TM w/ gage blocks and thread wires Crimper Tools Up to 2 in in Optical comparator Levels Up to 12 in 18 in/ft Sine plate & gage blocks (A2LA Cert. No ) 10/09/2015 Page 2 of 24

3 Parameter/Equipment Range CMC 2, 5 ( ) Comments Surface Plates 3 Flatness Up to 12 in 16 in Gage blocks, MU-checker (12 to 60) in 84 in Surface plate, planekator, Repeat-o-meter Repeatability Up to 60 in 27 in Repeat-o-meter Precision Balls Up to 1 in Up to 4 in 21 in 23 in MU checker, universal supermic & gage blocks Parallels Up to 24 in 37 in MU checker, granite parallels & gage blocks Precision Squares Up to 24 in 37 in Master Square, MU-check, true square Cylindrical Squares Up to 24 in 37 in Ultradex, MU checker Granite Squares & Granite Angle Blocks Up to 24 in 0, 00, 0.37 Ultradex, true square, auto collimator II. Dimensional Testing/Calibration 1 Parameter/Equipment Range CMC 2 ( ) Comments Length 3 Dimensional 6 X, Y & Z Up to 28 in Up to 56 in 330 in 470 in Mitutoyo B231 CMM (A2LA Cert. No ) 10/09/2015 Page 3 of 24

4 III. Electrical DC/Low Frequency Parameter/Equipment Range CMC 2, 8 ( ) Comments DC Voltage Generate 3 (0 to 220) mv (0.22 to 2.2) V (2.2 to 11) V (11 to 22) V (22 to 220) V (220 to 1100) V 8 µv/v µv 7 µv/v µv 7 µv/v µv 7 µv/v µv 8 µv/v + 81 µv 9 µv/v µv Fluke 5700A/5725A (1000 to ) V 0.12 % µv Ross VD B-K-AC, DMM, high voltage source DC Voltage Measure 3 (0 to 100) mv (0.1 to 1) V (1 to 10) V (10 to 100) V (100 to 1000) V* 6.4 V/V V 4.8 V/V V 4.7 V/V + 1 V 7.3 V/V + 30 V 8 V/V mv* HP 3458A OPT-2 *add 12(V in /1000) 2 ppm to all V in > 100 (1000 to ) V 0.12 % V Ross VD B-K-AC DC Current Generate 3 (0 to 220) µa (0.22 to 2.2) ma (2.2 to 22) ma (22 to 220) ma (0.22 to 2.2) A (2.2 to 11) A 50 µa/a + 8 na 51 µa/a na 50 µa/a + 16 na 60 µa/a µa 82 µa/a + 25 µa % µa Fluke 5700A/5725A (11 to 20.5) A % µa Fluke 5520A/SC600 (11 to 20) A (20 to 100) A % + 3 ma % + 3 ma Valhalla 2555A Clamp Meters (>20.5 to <150) A (150 to 1025) A 0.6 % A 0.6 % A Fluke 5500A/coil & 5520A/SC600 DC Current Measure 3 (10 to 100) A (0.1 to 1) ma (1 to 10) ma (10 to 100) ma (0.1 to 1) A 27 A/A na 26 A/A + 5 na 26 A/A + 50 na 43 A/A A % + 10 A HP 3458A opt-2 (1 to 2) A (2 to 20) A (20 to 100) A 0.7 ma 4.8 ma 59 ma Valhalla 2575A (A2LA Cert. No ) 10/09/2015 Page 4 of 24

5 Parameter/Equipment Range CMC 2, 8 ( ) Comments Resistance Generate 3 (0 to 11) (11 to 33) (33 to 110) (110 to 330) (0.33 to 1.1) k (1.1 to 3.3) k (3.3 to 11) k (11 to 33) k (33 to 110) k (110 to 330) k (0.33 to 1.1) M (1.1 to 3.3) M (3.3 to 11) M (11 to 33) M (33 to 110) M (110 to 330) M (0.33 to 1.1) G 32 / + 1 m 24 / m 23 / m 27 / + 2 m 22 / + 2 m 26 / + 20 m 22 / + 20 m 25 / / / / / % % k % + 3 k 0.23 % M 1.2 % M Fluke 5520A/SC600 Fixed Points Ω 0.01 Ω 0.1 Ω 1 Ω % nω % µω % µω % µω Standard resistors Guildline, L&N 0 Ω 1 Ω 1.9 Ω 10 Ω 19 Ω 100 Ω 190 Ω 1 kω 1.9 kω 10 kω 19 kω 100 kω 190 kω 1 MΩ 1.9 MΩ 10 MΩ 19 MΩ 100 MΩ 55 µω 95 µω/ω + 20 µω 95 µω/ω + 36 µω 28 µω/ω µω 27 µω/ω µω 17 µω/ω µω 17 µω/ω µω 13 µω/ω mω 13 µω/ω mω 12 µω/ω + 23 mω 12 µω/ω + 56 mω 14 µω/ω mω 14 µω/ω mω 20 µω/ω + 10 Ω 21 µω/ω + 34 Ω 40 µω/ω Ω 47 µω/ω Ω 47 µω/ω kω Fluke 5700A 100 MΩ 1 GΩ 10 GΩ 100 GΩ 1 TΩ 0.26 % MΩ 0.26 % GΩ 0.26 % GΩ 0.26 % GΩ 0.26 % TΩ Keithley 5155 (A2LA Cert. No ) 10/09/2015 Page 5 of 24

6 Parameter/Equipment Range CMC 2, 8 ( ) Comments Resistance Measure 3 (0 to 10) (10 to 100) (0.1 to 1) k (1 to 10) k (10 to 100) k (0.1 to 1) M (1 to 10) M (10 to 100) M (100 to 1000) M 20 / / m 12 / m 12 / + 5 m 12 / + 50 m 18 / / % + 1 k 24 % + 10 k HP 3458A opt-2 Capacitance Generate 3 (0.19 to <3.3) nf (3.3 to <11) nf (11 to <110) nf (110 to <330) nf (0.33 to <1.1) µf (1.1 to <3.3) µf (3.3 to <11) µf (11 to <33) µf (33 to <110) µf (110 to <330) µf (0.33 to <1.1) mf (1.1 to <3.3) mf (3.3 to <11) mf (11 to <33) mf (33 to <110) mf 0.58 % + 12 pf 0.29 % + 12 pf 0.29 % pf 0.29 % pf 0.29 % nf 0.29 % nf 0.29 % + 12 nf 0.46 % + 36 nf 0.52 % nf 0.52 % nf 0.52 % µf 0.52 % µf 0.52 % + 12 µf 0.87 % + 35 µf 1.3 % µf Fluke 5520A Phase Angle Generate 3 (0.5 and 3) V Fluke 5520A/SC600 (10 to 65) Hz (65 to 500) Hz (0.5 to 1) khz (1 to 5) khz (5 to 10) khz (10 to 30) khz (-180 to 180) (A2LA Cert. No ) 10/09/2015 Page 6 of 24

7 Parameter/Equipment Range CMC 2 ( ) Comments Electrical Simulation of Thermocouples Indicating Devices Generate and Measure 3 Type E -250 C to -100 C -100 C to -25 C -25 C to 350 C 350 C to 650 C 650 C to 1000 C 0.42 C 0.23 C 0.17 C 0.21 C 0.23 C Fluke 5520A Type J -210 C to -100 C -100 C to -30 C -30 C to 150 C 150 C to 760 C 760 C to 1200 C 0.25 C 0.21 C 0.17 C 0.19 C 0.26 C Type K -200 C to -100 C -100 C to -25 C -25 C to 120 C 120 C to 1000 C 1000 C to 1372 C 0.31 C 0.2 C 0.19 C 0.26 C 0.36 C Type T -250 C to -150 C -150 C to 0 C 0 C to 120 C 120 C to 400 C 0.53 C 0.23 C 0.18 C 0.17 C (A2LA Cert. No ) 10/09/2015 Page 7 of 24

8 Parameter/Equipment Range 4 CMC 2, 8 ( ) Comments Oscilloscopes 3 DC Signal Into 50 Ω (1 to ) mv (25 to ) mv 110 mv to V (2.2 to 6.599) V mv + 40 µv 0.21 mv + 40 µv V + 40 µv V + 40 µv Fluke 5520A/SC600 Into 1 MΩ (1 to ) mv (25 to ) mv 110 mv to V (2.2 to ) V (11 to 130) V mv + 40 µv mv + 40 µv V + 40 µv V + 40 µv V + 40 µv Level Sine Wave 50 khz Reference 50 khz to 100 MHz (100 to 300) MHz (300 to 600) MHz Bandwidth 5 mv to 5.5 V 5 mv to 5.5 V 5 mv to 5.5 V 5 mv to 5.5 V 1.6 % mv 3.4 % mv 4.0 % mv 6.7 % mv Square Wave 50, 10 Hz to 10 khz 1 M, 10 Hz to 1 khz 1 M, (1 to 10) khz 1 mv to V 1 mv to 130 V 1 mv to 130 V 0.19 % + 40 µv % + 40 µv 0.19 % + 40 µv Time Marker Output Into 50 (2 to 5) ns 10 ns (20 to 50) ns (20 to 100) ms 16 parts in 10 6 s 6.3 parts in 10 6 s 5.5 parts in 10 6 s 11 parts in 10 6 s Pulse Rise Time 1 khz to 10 MHz 240 ps (A2LA Cert. No ) 10/09/2015 Page 8 of 24

9 Parameter/Range Frequency CMC 2, 8 ( ) Comments AC Voltage Generate 3 (0.22 to 2.2) mv (10 to 20) Hz (20 to 40) Hz (0.04 to 20) khz (20 to 50) khz (100 to 300) khz (300 to 500) khz (0.5 to 1) MHz % µv % µv % µv % µv % µv 0.11 % + 14 µv 0.17 % + 27 µv 0.34 % + 31 µv Fluke 5700A opt 03 & 5725A (2.2 to 22) mv (10 to 20) Hz (20 to 40) Hz (0.04 to 20) khz (20 to 50) khz (100 to 300) khz (300 to 500) khz (0.5 to 1) MHz % + 11 µv % µv % + 12 µv % + 13 µv % + 13 µv 0.11 % + 27 µv 0.17 % + 39 µv 0.34 % + 55 µv (22 to 220) mv (10 to 20) Hz (20 to 40) Hz (0.04 to 20) khz (20 to 50) khz (100 to 300) khz (300 to 500) khz (0.5 to 1) MHz % + 63 µv % + 23 µv % + 14 µv % + 22 µv % + 50 µv 0.11 % + 72 µv 0.17 % µv 0.34 % µv (0.22 to 2.2) V (10 to 20) Hz (20 to 40) Hz (0.04 to 20) khz (20 to 50) khz (100 to 300) khz (300 to 500) khz (0.5 to 1) MHz 0.05 % µv % µv % + 71 µv % µv % µv 0.43 % µv 0.11 % µv 0.22 % mv (2.2 to 22) V (10 to 20) Hz (20 to 40) Hz (0.04 to 20) khz (20 to 50) khz (100 to 300) khz 0.05 % mv % mv % mv % mv % mv 0.05 % + 5 mv (22 to 220) V (10 to 20) Hz (20 to 40) Hz (0.04 to 20) khz (20 to 50) khz 0.05 % + 66 mv % + 16 mv % mv % + 17 mv (A2LA Cert. No ) 10/09/2015 Page 9 of 24

10 Parameter/Range Frequency CMC 2, 8 ( ) Comments AC Voltage Generate 3 (cont) (22 to 220) V (100 to 300) khz (300 to 500) khz (0.5 to 1) MHz 0.05 % + 25 mv 0.15 % + 93 mv 0.47 % + 93 mv 1.2 % mv Fluke 5700A opt 03 & 5725A (220 to 250) V (15 to 50) Hz 0.04 % + 23 mv (220 to 1100) V (0.04 to 1) khz (1 to 20) khz (20 to 30) khz % + 53 mv % + 52 mv 0.06 % + 70 mv (220 to 750) V (30 to 50) khz 0.06 % + 70 mv 0.23 % + 51 mv (1000 to ) V (50 to 60) Hz 0.6 % mv Ross VD B-K-AC, DMM, high voltage source Wideband AC Voltage Generate 3 Amplitude (0.3 to 1.1) mv (1.1 to 3) mv (3 to 11) mv (11 to 33) mv (33 to 110) mv (110 to 330) mv (0.3 to 1.1) V (1.1 to 3.5) V (0.03 to 500) khz 0.8 % µv 0.7 % µv 0.7 % µv 0.6 % + 17 µv 0.6 % + 41 µv 0.5 % µv 0.5 % µv 0.4 % µv Fluke 5700A opt 03 Flatness Relative to 1 khz Reference 0.3 mv to 3.5 V (10 to 30) Hz (30 to 120) Hz (0.12 to 120) khz (0.12 to 1.2) MHz (1.2 to 2) MHz (2 to 10) MHz (10 to 20) MHz (20 to 30) MHz 0.3 % µv 0.1 % µv 0.1 % µv 0.1 % µv 0.14 % µv 0.22 % µv 0.45 % µv 1 % µv (A2LA Cert. No ) 10/09/2015 Page 10 of 24

11 Parameter/Range Frequency CMC 2, 8 ( ) Comments AC Voltage Measure 3 (1 to 10) mv (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (20 to 50) khz (100 to 300) khz % + 3 V % V % V 0.12 % V 0.61 % V 4.7 % + 2 V HP 3458A opt 2 (10 to 100) mv (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (20 to 50) khz (100 to 300) khz 300 khz to 1 MHz % + 4 V % + 2 V % + 2 V % + 2 V % + 2 V 0.76 % + 10 V 1.2 % + 10 V (0.1 to 1) V (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (20 to 50) khz (100 to 300) khz 300 khz to 1 MHz % + 40 V % + 20 V % + 20 V % + 20 V % + 20 V 0.35 % mv 1.2 % mv (1 to 10) V (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (20 to 50) khz (100 to 300) khz 300 khz to 1 MHz % mv % mv % mv % mv % mv 0.35 % mv 1.2 % mv (10 to 100) V (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (20 to 50) khz (100 to 300) khz 300 khz to 1 MHz % + 4 mv % + 2 mv % + 2 mv % + 2 mv 0.14 % + 2 mv 0.46 % + 10 mv 1.7 % + 10 mv (100 to 1000) V (1 to 40) Hz 40 Hz to 1 khz (1 to 20) khz (20 to 50) khz % + 40 mv % + 20 mv % + 20 mv 0.14 % + 20 mv 0.35 % + 20 mv (1000 to ) V (50 to 60) Hz 0.6 % mv Ross VD B-K- AC (A2LA Cert. No ) 10/09/2015 Page 11 of 24

12 Parameter/Range Frequency CMC 2, 8 ( ) Comments AC Voltage Flatness Measure 3 Relative to 1 khz Reference (0 to 3) V (10 to 100) Hz (0.1 to 100) khz (100 to 300) khz (0.3 to 1) MHz (1 to 10) MHz (10 to 30) MHz (30 to 50) MHz (50 to 70) MHz (70 to 80) MHz (80 to 100) MHz 0.2 % % 0.1 % 0.13 % 0.22 % 0.27 % 0.47 % 0.66 % 0.75 % 0.88 % Thermal converters and H-P 3458A AC Current 3 Generate (9 to 220) µa (10 to 20) Hz (20 to 40) Hz (40 to 1000) Hz (1 to 5) khz (5 to 10) khz 0.07 % + 25 na % + 20 na % + 16 na 0.06 % + 40 na 0.16 % + 80 na Fluke 5700A/ 5725A (0.22 to 2.2) ma (10 to 20) Hz (20 to 40) Hz (40 to 1000) Hz (1 to 5) khz (5 to 10) khz 0.07 % + 65 na % + 62 na % + 38 na 0.06 % na 0.16 % na (2.2 to 22) ma (10 to 20) Hz (20 to 40) Hz (40 to 1000) Hz (1 to 5) khz (5 to 10) khz 0.07 % + 5 µa % + 2 µa % µa 0.06 % µa 0.16 % µa (22 to 220) ma (10 to 20) Hz (20 to 40) Hz (40 to 1000) Hz (1 to 5) khz (5 to 10) khz 0.07 % + 51 µa % + 51 µa % + 21 µa 0.06 % + 42 µa 0.16 % + 81 µa (0.22 to 2.2) A (20 to 1000) Hz (1 to 5) khz (5 to 10) khz % µa % µa 0.85 % µa (A2LA Cert. No ) 10/09/2015 Page 12 of 24

13 Parameter/Range Frequency CMC 2, 8 ( ) Comments AC Current 3 Generate (cont) (2.2 to 11) A (40 to 1000) Hz (1 to 5) khz (5 to 10) khz % µa % µa 0.36 % µa Fluke 5700A/ 5725A (2 to 100) A (45 to 1000) Hz 0.35 % A Valhalla 2555A Clamp Meters (>20.5 to <150) A (150 to 1025) A (>20.5 to <150) A (150 to 1025) A (45 to 65) Hz (> 65 to 440) Hz 0.68 % A 0.67 % +1.2 A 1.2 % A 1.2 % A Fluke 5500A/Coil & 5520A/SC600 LCOMP OFF AC Current Measure 3 (5 to 100) µa (0.1 to 1) ma (1 to 10) ma (10 to 100) ma (0.1 to 1) A (45 to 5000) Hz 0.07 % A 0.07 % A % + 2 A % + 20 A 0.12 % ma HP 3458A opt-2 (1 to 2) A (2 to 20) A (20 to 100) A (45 to 1000) Hz 0.14 % ma 0.12 % + 2 ma 0.12 % + 2 ma Valhalla 2575A IV. Electrical RF/Microwave Parameter/Range Frequency CMC 2 ( ) Comments RF Power Generate (13 to -5) db (-20 to -58) db (-50 to -80) db 200 Hz to 80 MHz 0.09 db 0.13 db 0.25 db HP 3335A (25 to >20) dbm (20 to -10) dbm (-10 to -90) dbm 250 khz to 20 GHz 1.2 db 0.96 db 1.2 db Agilent E8257D (A2LA Cert. No ) 10/09/2015 Page 13 of 24

14 Parameter/Range Frequency CMC 2, 8 ( ) Comments RF Power Generate (cont) (10 to -10) dbm (-10 to >-60) dbm (-60 to -110) dbm (20 to 26.5) GHz 1.1 db 1.4 db 2 db HP 83630B (10 to -20) dbm (26.5 to 50) GHz 2.4 db HP 83650B RF Power Measure 3 0 dbm 50 MHz 0.4 % HP 432A, 478A-H76, 3458A (-50 to +30) dbm 9 khz to 18 GHz 0.11 db Agilent E4419A & E9304A-H19 (-70 to +20) dbm (0.01 to 18) GHz 0.09 db Agilent E4419A & E4412A (-30 to +20) dbm (0.01 to 50) GHz 0.19 db Agilent E4419A & 8487A RF Tuned Power/ Attenuation Measure 3 (+16 to -10) dbm (-10 to -20) dbm (-20 to -30) dbm (-30 to -40) dbm (-40 to -50) dbm (-50 to -60) dbm (-60 to -70) dbm (-70 to -80) dbm (-80 to -90) dbm (-90 to -100) dbm <-100 dbm 100 khz to 50 GHz db db db 0.04 db db db db db db db 1.3 db Agilent N5531S (A2LA Cert. No ) 10/09/2015 Page 14 of 24

15 Parameter/Range Frequency CMC 2, 8 ( ) Comments RF Attenuation Generate (0 to -10) db (-10 to -20) db (-20 to -30) db (-30 to -40) db (-40 to -50) db (-50 to -60) db (-60 to -70) db (-70 to -80) db (-80 to -90) db (-90 to -100) db (-100 to -110) db (-110 to -121) 50 MHz db db db db db db db db db db db db Agilent 8494G & 8496G Amplitude Modulation Generate 50 Hz to 50 khz <95 % 50 Hz to 50 khz <99 % 20 Hz to 100 khz <95 % 20 Hz to 100 khz <99 % 20 Hz to 10 MHz <95 % 20 Hz to 10 MHz <99 % (11 to 13.5) MHz 0.25 % 0.32 % 0.34 % 0.40 % 2.9 % 2.9 % HP 11715A Amplitude Modulation Measure Rate: 50 Hz to 10 khz Depth: (5 to 99) % (0.1 to 10) MHz 0.87 % Agilent N5531S Rate: 50 Hz to 100 khz Depth: (5 to 20) % (20 to 99) % (0.01 to 3) GHz 2.9 % 0.58 % Depth: (5 to 20) % (20 to 99) % (3 to 26.5) GHz 5.2 % 1.7 % Depth: (5 to 20) % (20 to 99) % (26.5 to 31.15) GHz 7.9 % 2.3 % Depth: (5 to 20) % (20 to 99) % (31.15 to 50) GHz 30 % 7 % (A2LA Cert. No ) 10/09/2015 Page 15 of 24

16 Parameter/Range Frequency CMC 2, 8 ( ) Comments Frequency Modulation Generate DC to 10 MHz Rate (11 to 432) MHz 0.15 % HP 11715A Frequency Modulation Measure Rate: 20 Hz to 10 khz Deviation: 200 Hz to 40 khz Rate: 50 Hz to 200 khz Deviation: 250 Hz to 400 khz (0.25 to 10) MHz >0.2 ß >1.2 ß (0.01 to 6.6) GHz >0.2 ß >0.45 ß 1.7 % Hz 1.2 % Hz 1.7 % Hz 1.2 % + 27 Hz Agilent N5531S ß is the ratio of frequency deviation to modulation rate (6.6 to 13.2) GHz >0.2 ß >8 ß 2.9 % + 19 Hz 1.2 % + 19 Hz (13.2 to 31.15) GHz >0.2 ß >16 ß 4.4 % + 27 Hz 1.2 % + 25 Hz (31.15 to 50) GHz >0.2 ß >32 ß 9.8 % Hz 1.2 % Hz Phase Modulation Measure > 0.7 rad > 0.3 rad 100 khz to 6.6 GHz 1.2 % rad 3.5 % rad Agilent N5531S > 2 rad > 0.6 rad (6.6 to 13.2) GHz 1.2 % rad 3.5 % rad > 4 rad > 1.2 rad (13.2 to 26.5) GHz 1.2 % rad 3.5 % rad > 4 rad > 1.3 rad (26.5 to 31.5) GHz 1.2 % rad 3.5 % rad > 8 rad > 2.4 rad (31.5 to 50) GHz 1.2 % rad 3.5 % rad (A2LA Cert. No ) 10/09/2015 Page 16 of 24

17 Parameter/Range Frequency CMC 2 ( ) Comments Digital Modulation Measure, Carrier: 2 MHz to 2.65 GHz Error Vector Magnitude Formats Other Than FSK Mod Frequency Span: (1 to 100) khz (0.1 to 1) MHz 1 MHz to 2.65 GHz 0.35 % rms 0.58 % rms 1.2 % rms HP 89441A Error Vector Magnitude For FSK Modulation Mod Frequency: 3.2 khz khz 0.58 % rms 1.7 % rms Phase Error for Modulation (1 to 100) khz (0.1 to 1) MHz 1 MHz to 2.65 GHz 0.2 rms 0.39 rms 0.66 rms Phase Noise Measure (0.25 to 1.6) GHz Offsets from CW 1 Hz 10 Hz 100 Hz 1 khz 10 khz 100 khz 2.6 dbc/hz 2.6 dbc/hz 2.5 dbc/hz 2.4 dbc/hz 2.4 dbc/hz 2.3 dbc/hz Agilent E8257D & N5500A (1.2 to 20) GHz Offsets from CW 1 Hz 10 Hz 100 Hz 1 khz 10 khz 100 khz 2.8 dbc/hz 2.5 dbc/hz 2.4 dbc/hz 2.4 dbc/hz 2.4 dbc/hz 2.3 dbc/hz Phase Noise Generate 3 (0.25 to 20) GHz Offsets from CW 1 Hz 10 Hz 100 Hz 1 khz 10 khz 100 khz 2.5 dbc/hz 2.6 dbc/hz 2.4 dbc/hz 2.3 dbc/hz 2.3 dbc/hz 2.3 dbc/hz Agilent E8257D (A2LA Cert. No ) 10/09/2015 Page 17 of 24

18 Parameter/Range Frequency CMC 2, 8 ( ) Comments Audio Distortion (0.02 to 250) khz 0.35 % Agilent N5531S Measure 3 Reflection S 11 /S 22 Measure (0.6 to 1) lin (0.2 to 0.5) lin 45 MHz to 18 GHz (0.012 to ) lin (0.83 to ) ( to ) lin (1.1 to + 1.8) H-P 8510C, 85054A type-n (sliding load cal) (0.0 to 0.1) lin ( to ) lin (3.3 to +180) (0.6 to 1) lin (0.2 to 0.5) lin 45 MHz to 20 GHz ( to ) lin (0.63 to ) ( to ) lin (0.77 to + 1.4) H-P 8510C, 85050A 7 mm (TRL cal) (0.0 to 0.1) lin ( to ) lin (2.3 to +180) (0.6 to 1) lin (0.2 to 0.5) lin 45 MHz to 26.5 GHz (0.014 to ) lin (1.2 to + 1.2) ( to ) lin (1.3 to + 2.1) H-P 8510C, 85052B 3.5 mm (sliding load cal) (0.0 to 0.1) lin ( to ) lin (3.3 to + 180) Transmission S 12 /S 21 Measure 10 db 0 db -10 db -20 db 45 MHz to 18 GHz (0.13 to ) db (1.3 to + 4.2) (0.051 to ) db (0.21 to + 3.9) (0.066 to ) db (0.33 to + 4) (0.067 to ) db (0.34 to + 4) H-P 8510C, 85054A type-n (sliding load cal) (A2LA Cert. No ) 10/09/2015 Page 18 of 24

19 Parameter/Equipment Frequency CMC 2 ( ) Comments Transmission S 12 /S 21 Measure (cont) -30 db -40 db 45 MHz to 18 GHz (0.07 to ) db (0.37 to + 4) (0.076 to ) db (0.45 to + 4.2) H-P 8510C, 85054A type-n (sliding load cal) -50 db (0.11 to + 0.2) db (0.73 to + 4.8) -60 db (0.24 to ) db (1.7 to + 6.7) 10 db 0 db 45 MHz to 20 GHz (0.068 to ) db (1.3 to + 3.8) (0.046 to ) db (0.18 to + 3.6) H-P 8510C, 85050A 7 mm (TRL cal) -10 db (0.05 to ) db (0.3 to + 3.7) -20 db (0.051 to ) db (0.31 to + 3.7) -30 db (0.054 to ) db (0.34 to + 3.7) -40 db (0.063 to ) db (0.43 to + 3.9) -50 db (0.11 to ) db (0.72 to + 4.5) -60 db (0.24 to ) db (1.7 to + 6.4) (A2LA Cert. No ) 10/09/2015 Page 19 of 24

20 Parameter/Equipment Frequency CMC 2 ( ) Comments Transmission S 12 /S 21 Measure (cont) 10 db 0 db -10 db -20 db -30 db -40 db -50 db -60 db 45 MHz to 26.5 GHz (0.13 to ) db (1.3 to + 5.8) (0.054 to ) db (0.21 to + 5.7) (0.069 to ) db (0.31 to + 5.7) (0.07 to ) db (0.34 to + 5.7) (0.073 to ) db (0.38 to + 5.9) (0.076 to + 0.2) db (0.46 to + 6.4) (0.11 to ) db (0.75 to + 8.1) (0.24 to + 1.4) db (1.7 to + 14) H-P 8510C, 85052B 3.5 mm (sliding load cal) (A2LA Cert. No ) 10/09/2015 Page 20 of 24

21 V. Mechanical Parameter/Equipment Range 4 CMC 2, 5, 9 ( ) Comments Mass Measure (1 to 500) mg 1 g 2 g 5 g 10 g 20 g 50 g 100 g 200 g 500 g 1 kg 2 kg 5 kg 10 kg 20 kg 8.7 µg 24 µg 25 µg 27 µg 30 µg 58 µg 0.12 mg 0.22 mg 0.45 mg 58 mg 58 mg 58 mg 65 mg 0.58 g 0.58 g Troemner Ultra-Class weight set and electronic balances Scales & Balances 3 (1 to 500) mg 1 g 2 g 5 g 10 g 20 g 50 g 100 g 200 g 500 g 1 kg 2 kg 5 kg 10 kg 20 kg 30 kg 8.7 µg R 24 µg R 25 µg R 27 µg R 30 µg R 58 µg R 0.11 mg R 0.21 mg R 0.44 mg R 1 mg R 2.1 mg R 4.2 mg R 10 mg R 21 mg R 42 mg R 70 mg R Troemner Ultra-Class weight set (0 to 500) lb 0.02 % R Class F weights Torque Transducers (8 to 100) in lbf (10 to 100) ft lbf (100 to 1000) ft lbf 0.13 % 0.13 % 0.30 % Torque wheels and torque arms with Ultra Class & Class F weights Torque 3 Wrenches & Drivers (10 to 100) in lbf (8 to 100) ft lbf (100 to 1000) ft lbf 0.17 % 0.30 % 0.35 % AKO TSD 2050 torque system Vacuum 3 (0.01 to 10) Torr (10 to 1000) Torr % % MKS reference transducers (A2LA Cert. No ) 10/09/2015 Page 21 of 24

22 Parameter/Equipment Range CMC 2, 5, 9 ( ) Comments Pressure 3 Nitrogen Gas (0.01 to 1000) Torr 0.24 Torr Mensor 2101 (0.2 to 600) psi % R Ruska Oil (45 to 1000) psi (>1000 to ) psi % % DH 4817 system (100 to ) psi ( to ) psi % % Ruska 2450 Air Velocity Generate (30 to 250) FPM (250 to 1500) FPM (1500 to 9000) FPM 2.4 % R 2.4 % R 1.3 % R TSI 8390 wind tunnel Pipettes (2 to 10) µl (10 to 100) µl (100 to 500) µl (500 to 1000) µl (1000 to 5000) µl µl 0.10 µl 0.52 µl 1.1 µl 1.4 µl Gravimetric calibration using Mettler MT5 & AT200 Force Gages Tension & Compression 3 Up to 10 lbf (10 to 100) lbf (100 to 500) lbf lbf lbf 0.15 lbf Weights, weight hangers VI. Thermodynamic Parameter/Equipment Range CMC 2 ( ) Comments Infrared (50 to 100) C Thermometers 3, 7 (100 to 300) C (300 to 500) C 0.61 C 0.78 C 1 C Hart scientific 9132 Temperature (-200 to 0) C Measure 3 (0 to 350) C (350 to 660) C C C 0.12 C Isotech TTI-8 & Fluke 5609 (A2LA Cert. No ) 10/09/2015 Page 22 of 24

23 Parameter/Equipment Range CMC 2 ( ) Comments Relative Humidity Measure 3 (5 to 15) % RH (>15 to 35) % RH (>35 to 55) % RH (>55 to 77) % RH (>77 to 95) % RH 0.15 % RH 0.33 % RH 0.49 % RH 0.7 % RH 0.83 % RH RH Systems 973 Frost & Dew Point Measure (-50 to < 0) C (0 to 20) C 0.15 C 0.13 C RH Systems 973 VII. Time & Frequency Parameter/Equipment Range 4 CMC 2, 9 ( ) Comments Frequency Measuring Equipment 3 GPS Reference 10 MHz 1 PPS (4.5 x ) Hz (7.2 x ) Hz Symmetricom Xli GPS (0 to 10) MHz (>0.01 to 12) GHz (>12 to 50) GHz (4.5 x ) Hz (33 x ) Hz (2.7 x ) Hz GPS, H-P 3325A & 83650B Frequency Measure 3 (0 to 10) MHz (>0.01 to 12) GHz (>12 to 50) GHz (4.5 x ) Hz (33 x ) Hz (2.7 x ) Hz Symmetricom Xli GPS, Agilent 53132A-124 & N5531S Timers & Stopwatches 3 Up to 24 hours 46 ms Symmetricom Xli GPS, H-P 53132A & 3325B Timing Measure 3 Time Interval DC to 50 GHz 9.2 ps % H-P 54750A & 54752A (A2LA Cert. No ) 10/09/2015 Page 23 of 24

24 1 This laboratory offers commercial dimensional testing/calibration, and field calibration service. 2 Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer s device and to influences from the circumstances of the specific calibration. 3 Field calibration service is available for this calibration and this laboratory meets A2LA R104 General Requirements: Accreditation of Field Testing and Field Calibration Laboratories for these calibrations. Please note the actual measurement uncertainties achievable on a customer's site can normally be expected to be larger than the CMC found on the A2LA Scope. Allowance must be made for aspects such as the environment at the place of calibration and for other possible adverse effects such as those caused by transportation of the calibration equipment. The usual allowance for the actual uncertainty introduced by the item being calibrated, (e.g. resolution) must also be considered and this, on its own, could result in the actual measurement uncertainty achievable on a customer s site being larger than the CMC. 4 Where ranges are not specified, the CMC stated is for the cardinal points only. 5 In the statement of CMC, L is the numerical value of the nominal length of the device measured in inches or millimeters. In the statement of CMC, R is the numerical value of the resolution of the device. 6 This laboratory meets R205 Specific Requirements: Calibration Laboratory Accreditation Program for the types of dimensional tests listed above and is considered equivalent to that of a calibration. 7 Target Emissivity is not calibrated and assumed to be 0.95 (±0.02 from 8 to 14 μm) for Blackbody. 8 The stated measured values are determined using the indicated instrument (see Comments). This capability is suitable for the calibration of the devices intended to measure or generate the measured value in the ranges indicated. CMCs are expressed as either a specific value that covers the full range or as a fraction/percentage of the reading plus a fixed floor specification. 9 In the statement of CMC, a % is defined as the percentage of reading unless otherwise noted. (A2LA Cert. No ) 10/09/2015 Page 24 of 24

25 Accredited Laboratory A2LA has accredited SIMCO ELECTRONICS Chatsworth, CA for technical competence in the field of Calibration This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This laboratory also meets the requirements of ANSI/NCSLI Z and the requirements of ANSI/NCSLI Z and any additional program requirements in the field of calibration. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 9 th day of October President & CEO For the Accreditation Council Certificate Number Valid to September 30, 2017 For the calibrations to which this accreditation applies, please refer to the laboratory s Calibration Scope of Accreditation.