FCC RF Test Report. SPORTON INTERNATIONAL INC. No. 52, Hwa Ya 1 st Rd., Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan, R.O.C.

Transcription

1 PPLICNT : Xiaomi Communications Co., Ltd. EQUIPMENT : Mobile Phone BRND NME : MI MODEL NME : M84C3DG FCC ID : FZZ-RMSC3DG STNDRD : FCC Part 5 Subpart C 5.47 CLSSIFICTION : (DSS) Spread Spectrum Transmitter The product was received on pr. 6, 8 and testing was completed on Jun. 6, 8. We, SPORTON INTERNTIONL INC., would like to declare that the tested sample has been evaluated in accordance with the test procedures and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNTIONL INC., the test report shall not be reproduced except in full. Reviewed by: Joseph Lin / Supervisor pproved by: Jones Tsai / Manager SPORTON INTERNTIONL INC. No. 5, Hwa Ya st Rd., Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan, R.O.C. SPORTON INTERNTIONL INC. Page Number : of 58

2 TBLE OF CONTENTS REVISION HISTORY... 3 SUMMRY OF TEST RESULT... 4 GENERL DESCRIPTION pplicant Manufacturer Product Feature of Equipment Under Test Product Specification of Equipment Under Test Modification of EUT Testing Location pplicable Standards... 7 TEST CONFIGURTION OF EQUIPMENT UNDER TEST Carrier Frequency Channel Test Mode Connection Diagram of Test System....4 Support Unit used in test configuration and system....5 EUT Operation Test Setup....6 Measurement Results Explanation Example... 3 TEST RESULT Number of Channel Measurement Hopping Channel Separation Measurement Dwell Time Measurement db Bandwidth Measurement Output Power Measurement Conducted Band Edges Measurement Conducted Spurious Emission Measurement Radiated Band Edges and Spurious Emission Measurement C Conducted Emission Measurement ntenna Requirements LIST OF MESURING EQUIPMENT UNCERTINTY OF EVLUTION PPENDIX. C CONDUCTED EMISSION TEST RESULT PPENDIX B. RDITED SPURIOUS EMISSION PPENDIX C. DUTY CYCLE PLOTS PPENDIX D. SETUP PHOTOGRPHS SPORTON INTERNTIONL INC. Page Number : of 58

3 REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DTE FR8468- Rev. Initial issue of report Jun., 8 SPORTON INTERNTIONL INC. Page Number : 3 of 58

4 SUMMRY OF TEST RESULT Report Section FCC Rule Description Limit Result Remark (a)() Number of Channels 5Chs Pass (a)() Hopping Channel Separation /3 of db BW Pass (a)() Dwell Time of Each Channel.4sec in 3.6sec period Pass (a)() db Bandwidth N Pass (b)() Peak Output Power 5 mw Pass (d) Conducted Band Edges dbc Pass (d) Conducted Spurious Emission Radiated Band Edges dbc Pass - Under limit (d) and Radiated Spurious 5.9(a) & 5.47(d) Pass 3.3 db at Emission MHz C Conducted Emission 5.7(a) Pass Under limit 6. db at.5 MHz & 5.47(b) ntenna Requirement N/ Pass - SPORTON INTERNTIONL INC. Page Number : 4 of 58

5 General Description. pplicant Xiaomi Communications Co., Ltd. The Rainbow City of China Resources, NO.68, Qinghe Middle Street, Haidian District, Beijing, China. Manufacturer Xiaomi Communications Co., Ltd. The Rainbow City of China Resources, NO.68, Qinghe Middle Street, Haidian District, Beijing, China.3 Product Feature of Equipment Under Test Equipment Brand Name Model Name FCC ID EUT supports Radios application IMEI Code HW Version SW Version EUT Stage Remark: Product Feature Mobile Phone MI M84C3DG FZZ-RMSC3DG GSM/GPRS/EGPRS/WCDM/HSP/ DC-HSDP/HSP+/LTE WLN.4GHz 8.b/g/n HT Bluetooth v3. + EDR/ Bluetooth v 4. LE/ Bluetooth v 4. LE Conducted: N/ Conduction: / Radiation: / P MIUI9 Production Unit. The above EUT's information was declared by manufacturer. Please refer to the specifications or user's manual for more detailed description.. There are two types of EUT, the difference between two samples is for memory, the sample is 3+3GB capacity and the sample is 4+64GB capacity. ccording to the difference, we only choose sample to perform full test. SPORTON INTERNTIONL INC. Page Number : 5 of 58

6 .4 Product Specification of Equipment Under Test Standards-related Product Specification Tx/Rx Frequency Range 4 MHz ~ 48 MHz Number of Channels 79 Carrier Frequency of Each Channel 4+n* MHz; n=~78 Maximum Output Power to ntenna ntenna Type / Gain Type of Modulation Bluetooth BR(Mbps) : 9.86 dbm (.97 W) Bluetooth EDR (Mbps) : 9.33 dbm (.86 W) Bluetooth EDR (3Mbps) : 9.5 dbm (.84 W) IF ntenna with gain.38 dbi Bluetooth BR (Mbps) : GFSK Bluetooth EDR (Mbps) :π/4-dqpsk Bluetooth EDR (3Mbps) : 8-DPSK.5 Modification of EUT No modifications are made to the EUT during all test items..6 Testing Location SPORTON INTERNTIONL INC. is accredited to ISO 75 by Taiwan ccreditation Foundation (TF code : 9) and under the FCC-recognized accredited testing laboratories by Mutual Recognition greement (MR) in FCC Test. Test Site Test Site Location Test Site No. SPORTON INTERNTIONL INC. No. 5, Hwa Ya st Rd., Hwa Ya Technology Park, Kwei-Shan District, Tao Yuan City, Taiwan, R.O.C. TEL: FX: Sporton Site No. TH5-HY CO5-HY Note: The test site complies with NSI C requirement. Test Site Test Site Location Test Site No. SPORTON INTERNTIONL INC. No.58, ly. 75, Ln. 564 Wenha 3rd Rd. Guishan Dist. Taoyuan City Taiwan TEL: FX: FCC Test Firm Sporton Site No. FCC designation No. Registration No. 3CH-HY TW7 45 Note: The test site complies with NSI C requirement. SPORTON INTERNTIONL INC. Page Number : 6 of 58

7 .7 pplicable Standards ccording to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: FCC Part 5 Subpart C 5.47 NSI C63.-3 Remark:. ll test items were verified and recorded according to the standards and without any deviation during the test.. This EUT has also been tested and complied with the requirements of FCC Part 5, Subpart B, recorded in a separate test report. SPORTON INTERNTIONL INC. Page Number : 7 of 58

8 Test Configuration of Equipment Under Test. Carrier Frequency Channel Frequency Band Freq. Freq. Freq. Channel Channel Channel (MHz) (MHz) (MHz) MHz SPORTON INTERNTIONL INC. Page Number : 8 of 58

9 . Test Mode a. The EUT has been associated with peripherals and configuration operated in a manner tended to maximize its emission characteristics in a typical application. Frequency range investigated: conduction emission (5 khz to 3 MHz), radiation emission (9 khz to the th harmonic of the highest fundamental frequency or to 4 GHz, whichever is lower). For radiated measurement, pre-scanned in three orthogonal panels, X, Y, Z. The worst cases (X-Plane) were recorded in this report, and the worst mode of radiated spurious emissions is Bluetooth Mbps mode, and recorded in this report. b. C power line Conducted Emission was tested under maximum output power. The following summary table is showing all test modes to demonstrate in compliance with the standard. Summary table of Test Cases Data Rate / Modulation Test Item Bluetooth BR Mbps Bluetooth EDR Mbps Bluetooth EDR 3Mbps GFSK π/4-dqpsk 8-DPSK Conducted Test Cases Mode : CH_4 MHz Mode : CH39_44 MHz Mode 3: CH78_48 MHz Mode 4: CH_4 MHz Mode 5: CH39_44 MHz Mode 6: CH78_48 MHz Mode 7: CH_4 MHz Mode 8: CH39_44 MHz Mode 9: CH78_48 MHz Bluetooth BR Mbps GFSK Radiated Mode : CH_4 MHz Test Cases Mode : CH39_44 MHz Mode 3: CH78_48 MHz C Conducted Emission Mode : GSM 85 Idle + Bluetooth Link + WLN Link (.4G) + Camera(Rear) + USB Cable (Charging from dapter) + Earphone + SD Card + SIM Remark:. For radiated test cases, the worst mode data rate Mbps was reported only, because this data rate has the highest RF output power at preliminary tests, and no other significantly frequencies found in conducted spurious emission.. For Radiated Test Cases, The tests were performed with dapter, Earphone and USB Cable. SPORTON INTERNTIONL INC. Page Number : 9 of 58

10 .3 Connection Diagram of Test System.4 Support Unit used in test configuration and system Item Equipment Trade Name Model Name FCC ID Data Cable Power Cord. System Simulator R&S CMU N/ N/ Unshielded,.8 m. BT Base Station R&S CBT N/ N/ Unshielded,.8 m 3. WLN P SUS RT-C66U MSQ-RTC66U N/ Unshielded,.8m 4. Notebook Dell Latitude E63 FCC DoC N/ 5. Bluetooth Earphone Sony Ericsson MW6 PY79 N/ N/ 6. ipod Earphone pple 85 DoC UnShielded,.m N/ 7. SD Card SanDisk MicroSD HC FCC DoC N/ N/ C I/P: Unshielded,. m DC O/P: Shielded,.8 m SPORTON INTERNTIONL INC. Page Number : of 58

11 .5 EUT Operation Test Setup For Bluetooth function, the engineering test program was provided and enabled to make EUT connect with Bluetooth base station to continuous transmit/receive. For C power line conducted emissions, the EUT was set to connect with the Notebook under large package sizes transmission..6 Measurement Results Explanation Example For all conducted test items: The offset level is set in the spectrum analyzer to compensate the RF cable loss and attenuator factor between EUT conducted output port and spectrum analyzer. With the offset compensation, the spectrum analyzer reading level is exactly the EUT RF output level. Example: The spectrum analyzer offset is derived from RF cable loss and attenuator factor. Offset = RF cable loss + attenuator factor. Following shows an offset computation example with cable loss 5.3 db and db attenuator. Offset(dB) = RF cable loss(db) + attenuator factor(db). = = 5.3 (db) SPORTON INTERNTIONL INC. Page Number : of 58

12 3 Test Result 3. Number of Channel Measurement 3.. Limits of Number of Hopping Frequency Frequency hopping systems in the MHz band shall use at least 5 channels. 3.. Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedure. The testing follows NSI C63.-3 clause The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 3. Set to the maximum power setting and enable the EUT transmit continuously. 4. Enable the EUT hopping function. 5. Use the following spectrum analyzer settings: Span = the frequency band of operation; RBW = 3kHz; VBW RBW; Sweep = auto; Detector function = peak; Trace = max hold. 6. The number of hopping frequency used is defined as the number of total channel. 7. Record the measurement data derived from spectrum analyzer Test Setup 3..5 Test Result of Number of Hopping Frequency Test Mode : Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Number of Hopping (Channel) daptive Frequency Hopping (Channel) Limits (Channel) Pass/Fail 79 > 5 Pass SPORTON INTERNTIONL INC. Page Number : of 58

13 Number of Hopping Channel Plot on Channel - 78 * RBW 3 khz SWT.5 ms MXH Start.4 GHz 4. MHz/ Stop.44 GHz Date: 4.JUN.8 8:5: * RBW 3 khz SWT.5 ms MXH Start.44 GHz 4.5 MHz/ Stop.4835 GHz Date: 4.JUN.8 8:7:4 SPORTON INTERNTIONL INC. Page Number : 3 of 58

14 3. Hopping Channel Separation Measurement 3.. Limit of Hopping Channel Separation Frequency hopping systems operating in the MHz band may have hopping channel carrier frequencies that are separated by 5 khz or two-thirds of the db bandwidth of the hopping channel, whichever is greater. 3.. Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures. The testing follows NSI C63.-3 clause The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 3. Set to the maximum power setting and enable the EUT transmit continuously. 4. Enable the EUT hopping function. 5. Use the following spectrum analyzer settings: Span = wide enough to capture the peaks of two adjacent channels; RBW = 3kHz; VBW RBW; Sweep = auto; Detector function = peak; Trace = max hold. 6. Measure and record the results in the test report Test Setup SPORTON INTERNTIONL INC. Page Number : 4 of 58

15 3..5 Test Result of Hopping Channel Separation Test Mode : Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Channel Frequency (MHz) Frequency Separation (MHz) (/3 of db BW) Limits (MHz) Pass/Fail Pass Pass Pass Channel Separation Plot on Channel - * RBW 3 khz SWT.5 ms Delta [T ].3 db. MHz Marker [T ] 9.5 dbm.4 GHz MXH Center.45 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 7:3:9 SPORTON INTERNTIONL INC. Page Number : 5 of 58

16 Channel Separation Plot on Channel 39-4 * RBW 3 khz SWT.5 ms Delta [T ] -.3 db. MHz Marker [T ] 8.8 dbm.44 GHz MXH Center.445 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 7:39:35 Channel Separation Plot on Channel * RBW 3 khz SWT.5 ms Delta [T ] -.5 db.8 MHz Marker [T ] 9.79 dbm.4794 GHz MXH Center.4795 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 7:46:48 SPORTON INTERNTIONL INC. Page Number : 6 of 58

17 Test Mode : Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Channel Frequency (MHz) Frequency Separation (MHz) (/3 of db BW) Limits (MHz) Pass/Fail Pass Pass Pass Channel Separation Plot on Channel - * RBW 3 khz SWT.5 ms Delta [T ].4 db. MHz Marker [T ] 8.5 dbm.4846 GHz MXH Center.45 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9::39 SPORTON INTERNTIONL INC. Page Number : 7 of 58

18 Channel Separation Plot on Channel 39-4 * RBW 3 khz SWT.5 ms Delta [T ] -. db. MHz Marker [T ] 8. dbm GHz MXH Center.445 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9:4: Channel Separation Plot on Channel * RBW 3 khz SWT.5 ms Delta [T ] -.7 db. MHz Marker [T ] 8.9 dbm GHz MXH Center.4795 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9:5:7 SPORTON INTERNTIONL INC. Page Number : 8 of 58

19 Test Mode : 3Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Channel Frequency (MHz) Frequency Separation (MHz) (/3 of db BW) Limits (MHz) Pass/Fail Pass Pass Pass Channel Separation Plot on Channel - * RBW 3 khz SWT.5 ms Delta [T ].8 db. MHz Marker [T ] 8. dbm.4846 GHz MXH Center.45 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9:6:5 SPORTON INTERNTIONL INC. Page Number : 9 of 58

20 Channel Separation Plot on Channel 39-4 * RBW 3 khz SWT.5 ms Delta [T ] -.5 db. MHz Marker [T ] 8.5 dbm GHz MXH Center.445 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9:7:6 Channel Separation Plot on Channel * RBW 3 khz SWT.5 ms Delta [T ] -.4 db. MHz Marker [T ] 8.8 dbm GHz MXH Center.4795 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9:8:6 SPORTON INTERNTIONL INC. Page Number : of 58

21 3.3 Dwell Time Measurement 3.3. Limit of Dwell Time The average time of occupancy on any channel shall not be greater than.4 seconds within a period of.4 seconds multiplied by the number of hopping channels employed Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures. The testing follows NSI C63.-3 clause The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 3. Set to the maximum power setting and enable the EUT transmit continuously. 4. Enable the EUT hopping function. 5. Use the following spectrum analyzer settings: Span = zero span, centered on a hopping channel; RBW = MHz; VBW RBW; Sweep = as necessary to capture the entire dwell time per hopping channel; Detector function = peak; Trace = max hold. 6. Measure and record the results in the test report Test Setup SPORTON INTERNTIONL INC. Page Number : of 58

22 3.3.5 Test Result of Dwell Time Test Mode : 3DH5 Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Mode Hopping Channel Number Hops Over Occupancy Time(hops) Package Transfer Time (msec) Dwell Time (sec) Limits (sec) Pass/Fail Normal Pass FH Pass Package Transfer Time Plot RBW MHz * VBW MHz SWT ms Delta 3 [T ] -. db 3.76 ms MXH 3 Marker [T ] 8.57 dbm 74. µs Delta [T ] -.7 db.88 ms SGL Center.44 GHz ms/ Date: 4.JUN.8 6:4:4 Remark:. In normal mode, hopping rate is 6 hops/s with 6 slots in 79 hopping channels. With channel hopping rate (6 / 6 / 79) in Occupancy Time Limit (.4 x 79) (s), Hops Over Occupancy Time comes to (6 / 6 / 79) x (.4 x 79) = 6.67 hops.. In FH mode, hopping rate is 8 hops/s with 6 slots in hopping channels. With channel hopping rate (8 / 6 / ) in Occupancy Time Limit (.4 x ) (s), Hops Over Occupancy Time comes to (8 / 6 / ) x (.4 x ) = hops. 3. Dwell Time(s) = Hops Over Occupancy Time (hops) x Package Transfer Time SPORTON INTERNTIONL INC. Page Number : of 58

23 3.4 db Bandwidth Measurement 3.4. Limit of db Bandwidth Reporting only 3.4. Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures. The testing follows NSI C63.-3 clause 6.9. and The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 3. Set to the maximum power setting and enable the EUT transmit continuously. 4. Use the following spectrum analyzer settings for db Bandwidth measurement. Span = approximately to 5 times the db bandwidth, centered on a hopping channel; RBW % of the db bandwidth; VBW RBW; Sweep = auto; Detector function = peak; Trace = max hold. 5. Measure and record the results in the test report Test Setup SPORTON INTERNTIONL INC. Page Number : 3 of 58

24 3.4.5 Test Result of db Bandwidth Test Mode : Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Channel Frequency (MHz) db Bandwidth (MHz) db Bandwidth Plot on Channel * RBW 3 khz SWT.5 ms Delta [T ].9 db 796. khz MXH D 6.66 dbm Marker [T ] -3.8 dbm.46 GHz - D dbm Center.4 GHz khz/ Span MHz Date: 4.JUN.8 7:8:59 SPORTON INTERNTIONL INC. Page Number : 4 of 58

25 db Bandwidth Plot on Channel 39 * RBW 3 khz SWT.5 ms Delta [T ].6 db 88. khz MXH D 6.7 dbm Marker [T ] dbm GHz - - D dbm Center.44 GHz khz/ Span MHz Date: 4.JUN.8 7:38:3 db Bandwidth Plot on Channel 78 * RBW 3 khz SWT.5 ms Delta [T ].37 db 88. khz MXH D 7.5 dbm Marker [T ] -.8 dbm GHz - D -.85 dbm Center.48 GHz khz/ Span MHz Date: 4.JUN.8 7:45:5 SPORTON INTERNTIONL INC. Page Number : 5 of 58

26 Test Mode : Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Channel Frequency (MHz) db Bandwidth (MHz) db Bandwidth Plot on Channel * RBW 3 khz SWT 5 ms Delta [T ].7 db.4 MHz Marker [T ] -4. dbm.4376 GHz MXH D 5.43 dbm - - D dbm Center.4 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9::5 SPORTON INTERNTIONL INC. Page Number : 6 of 58

27 db Bandwidth Plot on Channel 39 * RBW 3 khz SWT 5 ms Delta [T ] -.8 db.48 MHz Marker [T ] -4.7 dbm GHz MXH D 5.48 dbm - - D -4.5 dbm Center.44 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9:5:4 db Bandwidth Plot on Channel 78 * RBW 3 khz SWT 5 ms Delta [T ] -.54 db.48 MHz Marker [T ] dbm GHz MXH D 5.56 dbm - - D dbm Center.48 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9:: SPORTON INTERNTIONL INC. Page Number : 7 of 58

28 Test Mode : 3Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Channel Frequency (MHz) db Bandwidth (MHz) db Bandwidth Plot on Channel * RBW 3 khz SWT 5 ms Delta [T ].5 db. MHz Marker [T ] -4.9 dbm.446 GHz MXH D 5.44 dbm - - D dbm Center.4 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9:36:58 SPORTON INTERNTIONL INC. Page Number : 8 of 58

29 db Bandwidth Plot on Channel 39 * RBW 3 khz SWT 5 ms Delta [T ].39 db. MHz Marker [T ] dbm.4446 GHz MXH D 5.5 dbm - - D dbm Center.44 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9:4:6 db Bandwidth Plot on Channel 78 * RBW 3 khz SWT 5 ms Delta [T ] -.73 db.8 MHz Marker [T ] dbm GHz MXH D 5.6 dbm - D dbm Center.48 GHz 3 khz/ Span 3 MHz Date: 4.JUN.8 9:49:9 SPORTON INTERNTIONL INC. Page Number : 9 of 58

30 3.5 Output Power Measurement 3.5. Limit of Output Power The maximum peak conducted output power of the intentional radiator shall not exceed the following: () For frequency hopping systems operating in the MHz band employing at least 75 non-overlapping hopping channels, and all frequency hopping systems in the MHz band: watt. For all other frequency hopping systems in the MHz band.5 watts. The power limit for Mbps, Mbps, 3Mbps and FH modes are.5 watts Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures. The testing follows NSI C63.-3 clause The RF output of EUT was connected to the power meter by RF cable and attenuator. The path loss was compensated to the results for each measurement. 3. Set to the maximum power setting and enable the EUT transmit continuously. 4. Measure the conducted output power with cable loss and record the results in the test report. 5. Measure and record the results in the test report Test Setup SPORTON INTERNTIONL INC. Page Number : 3 of 58

31 3.5.5 Test Result of Peak Output Power Test Mode : Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Channel Frequency (MHz) GFSK Mbps RF Power (dbm) Max. Limits (dbm) Pass/Fail Pass Pass Pass Test Mode : Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Channel Frequency (MHz) π/4-dqpsk Mbps RF Power (dbm) Max. Limits (dbm) Pass/Fail Pass Pass Pass Test Mode : 3Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Channel Frequency (MHz) 8-DPSK 3 Mbps RF Power (dbm) Max. Limits (dbm) Pass/Fail Pass Pass Pass SPORTON INTERNTIONL INC. Page Number : 3 of 58

32 3.6 Conducted Band Edges Measurement 3.6. Limit of Band Edges In any khz bandwidth outside the intentional radiation frequency band, the radio frequency power shall be at least db below the highest level of the radiated power. In addition, radiated emissions which fall in the restricted bands must also comply with the radiated emission limits Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures. The testing follows NSI C63.-3 clause Set to the maximum power setting and enable the EUT transmit continuously. 3. Set RBW = khz, VBW = 3kHz. Band edge emissions must be at least db down from the highest emission level within the authorized band as measured with a khz RBW. The attenuation shall be 3 db instead of db when RMS conducted output power procedure is used. 4. Enable hopping function of the EUT and then repeat step. and Measure and record the results in the test report Test Setup SPORTON INTERNTIONL INC. Page Number : 3 of 58

33 3.6.5 Test Result of Conducted Band Edges Test Mode : Mbps Temperature : ~5 Test Channel : and 78 Relative Humidity : 5~54% Test Engineer : Tommy Lee/Luffy Lin Low Band Edge Plot on Channel * RBW khz SWT.5 ms Marker [T ] -45. dbm.3954 GHz D 8.83 dbm MXH - D -.7 dbm Start.395 GHz F MHz/ Stop.45 GHz Date: 4.JUN.8 7:33:8 High Band Edge Plot on Channel 78 * RBW khz SWT.5 ms Marker [T ] dbm.4866 GHz D 9.34 dbm MXH - D -.66 dbm Start.4775 GHz F. MHz/ Stop.4895 GHz Date: 4.JUN.8 7:5:9 SPORTON INTERNTIONL INC. Page Number : 33 of 58

34 Test Mode : Mbps Temperature : ~5 Test Channel : and 78 Relative Humidity : 5~54% Test Engineer : Tommy Lee/Luffy Lin Low Band Edge Plot on Channel * RBW khz SWT.5 ms Marker [T ] dbm GHz MXH D 7.97 dbm - D -.3 dbm Start.395 GHz F MHz/ Stop.45 GHz Date: 4.JUN.8 9::36 High Band Edge Plot on Channel 78 * RBW khz SWT.5 ms Marker [T ] dbm GHz MXH D 8.6 dbm - D -.84 dbm Start.4775 GHz F. MHz/ Stop.4895 GHz Date: 4.JUN.8 9:9:3 SPORTON INTERNTIONL INC. Page Number : 34 of 58

35 Test Mode : 3Mbps Temperature : ~5 Test Channel : and 78 Relative Humidity : 5~54% Test Engineer : Tommy Lee/Luffy Lin Low Band Edge Plot on Channel * RBW khz SWT.5 ms Marker [T ] -45. dbm.3964 GHz MXH D 7.9 dbm - D -. dbm Start.395 GHz F MHz/ Stop.45 GHz Date: 4.JUN.8 9:36:5 High Band Edge Plot on Channel 78 * RBW khz SWT.5 ms Marker [T ] -45. dbm GHz D 8.3 dbm MXH - D -.68 dbm Start.4775 GHz F. MHz/ Stop.4895 GHz Date: 4.JUN.8 9:47:4 SPORTON INTERNTIONL INC. Page Number : 35 of 58

36 3.6.6 Test Result of Conducted Hopping Mode Band Edges Test Mode : Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Hopping Mode Low Band Edge Plot * RBW khz SWT.5 ms Marker [T ] dbm.3977 GHz D 8.83 dbm MXH - D -.7 dbm Start.395 GHz F MHz/ Stop.45 GHz Date: 4.JUN.8 7:58:3 Hopping Mode High Band Edge Plot * RBW khz SWT.5 ms Marker [T ] -44. dbm GHz D 9.4 dbm MXH - D -.6 dbm Start.4775 GHz F. MHz/ Stop.4895 GHz Date: 4.JUN.8 8::4 SPORTON INTERNTIONL INC. Page Number : 36 of 58

37 Test Mode : Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Hopping Mode Low Band Edge Plot * RBW khz SWT.5 ms Marker [T ] dbm.399 GHz MXH D 7.97 dbm - D -.3 dbm Start.395 GHz F MHz/ Stop.45 GHz Date: 4.JUN.8 8:57:57 Hopping Mode High Band Edge Plot * RBW khz SWT.5 ms Marker [T ] dbm GHz MXH D 7.3 dbm - D -.7 dbm Start.4775 GHz F. MHz/ Stop.4895 GHz Date: 4.JUN.8 8:58:59 SPORTON INTERNTIONL INC. Page Number : 37 of 58

38 Test Mode : 3Mbps Temperature : ~5 Test Engineer : Tommy Lee/Luffy Lin Relative Humidity : 5~54% Hopping Mode Low Band Edge Plot * RBW khz SWT.5 ms Marker [T ] dbm GHz MXH D 7.94 dbm - D -.6 dbm Start.395 GHz F MHz/ Stop.45 GHz Date: 4.JUN.8 9::39 Hopping Mode High Band Edge Plot * RBW khz SWT.5 ms Marker [T ] -45. dbm.4884 GHz MXH D 7.8 dbm - D -.7 dbm Start.4775 GHz F. MHz/ Stop.4895 GHz Date: 4.JUN.8 9::6 SPORTON INTERNTIONL INC. Page Number : 38 of 58

39 3.7 Conducted Spurious Emission Measurement 3.7. Limit of Spurious Emission Measurement In any khz bandwidth outside the intentional radiation frequency band, the radio frequency power shall be at least db below the highest level of the radiated power. In addition, radiated emissions which fall in the restricted bands must also comply with the radiated emission limits Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedure. The testing follows NSI C63.-3 clause The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. 3. Set to the maximum power setting and enable the EUT transmit continuously. 4. Set RBW = khz, VBW = 3kHz, scan up through th harmonic. ll harmonics / spurs must be at least db down from the highest emission level within the authorized band as measured with a khz RBW. 5. Measure and record the results in the test report. 6. The RF fundamental frequency should be excluded against the limit line in the operating frequency band Test Setup SPORTON INTERNTIONL INC. Page Number : 39 of 58

40 3.7.5 Test Result of Conducted Spurious Emission Test Mode : Mbps Temperature : ~5 Test Channel : Relative Humidity : 5~54% Test Engineer : Tommy Lee/Luffy Lin CSE Plot on Ch between 3MHz ~ 3 GHz * RBW khz SWT 3 ms Marker [T ] dbm.9764 GHz VIEW D 8.38 dbm Marker [T ] 8.38 dbm.46 GHz - D -.6 dbm Start 3 MHz 97 MHz/ Stop 3 GHz Date: 4.JUN.8 7:3:48 CSE Plot on Ch between GHz ~ 5 GHz * RBW khz SWT.3 s Marker [T ] -7.5 dbm.4 GHz VIEW D 8.34 dbm Marker [T ] 8.34 dbm.368 GHz - D -.66 dbm Start GHz.3 GHz/ Stop 5 GHz Date: 4.JUN.8 7:3:4 SPORTON INTERNTIONL INC. Page Number : 4 of 58

41 CSE Plot on Ch 39 between 3MHz ~ 3 GHz * RBW khz SWT 3 ms Marker [T ] dbm.9684 GHz D 8.7 dbm Marker [T ] 8.7 dbm.4464 GHz VIEW - D -.8 dbm Start 3 MHz 97 MHz/ Stop 3 GHz Date: 4.JUN.8 7:4:4 CSE Plot on Ch 39 between GHz ~ 5 GHz * RBW khz SWT.3 s Marker [T ] dbm.688 GHz VIEW D 8. dbm Marker [T ] 8. dbm.44 GHz - D -.98 dbm Start GHz.3 GHz/ Stop 5 GHz Date: 4.JUN.8 7:4:6 SPORTON INTERNTIONL INC. Page Number : 4 of 58

42 CSE Plot on Ch 78 between 3MHz ~ 3 GHz * RBW khz SWT 3 ms Marker [T ] dbm 3. GHz D 9.55 dbm Marker [T ] 9.55 dbm.483 GHz VIEW - D -.45 dbm Start 3 MHz 97 MHz/ Stop 3 GHz Date: 4.JUN.8 7:49:59 CSE Plot on Ch 78 between GHz ~ 5 GHz * RBW khz SWT.3 s Marker [T ] dbm.55 GHz D 8.93 dbm Marker [T ] 8.93 dbm.46 GHz VIEW - D -.7 dbm Start GHz.3 GHz/ Stop 5 GHz Date: 4.JUN.8 7:5:5 SPORTON INTERNTIONL INC. Page Number : 4 of 58

43 Test Mode : Mbps Temperature : ~5 Test Channel : Relative Humidity : 5~54% Test Engineer : CSE Plot on Ch between 3MHz ~ 3 GHz Tommy Lee/Luffy Lin * RBW khz SWT 3 ms Marker [T ] dbm 39.8 MHz VIEW D 6.68 dbm Marker [T ] 6.68 dbm.46 GHz - D -3.3 dbm Start 3 MHz 97 MHz/ Stop 3 GHz Date: 4.JUN.8 9:8:55 CSE Plot on Ch between GHz ~ 5 GHz * RBW khz SWT.3 s Marker [T ] dbm 4.63 GHz VIEW D 5.76 dbm Marker [T ] 5.76 dbm.368 GHz - D -4.4 dbm Start GHz.3 GHz/ Stop 5 GHz Date: 4.JUN.8 9:9:5 SPORTON INTERNTIONL INC. Page Number : 43 of 58

44 CSE Plot on Ch 39 between 3MHz ~ 3 GHz * RBW khz SWT 3 ms Marker [T ] dbm 9. MHz VIEW D 5.73 dbm Marker [T ] 5.73 dbm.4464 GHz - D -4.7 dbm Start 3 MHz 97 MHz/ Stop 3 GHz Date: 4.JUN.8 9:3:5 CSE Plot on Ch 39 between GHz ~ 5 GHz * RBW khz SWT.3 s Marker [T ] dbm.964 GHz VIEW D 5.94 dbm Marker [T ] 5.94 dbm.44 GHz - D -4.6 dbm Start GHz.3 GHz/ Stop 5 GHz Date: 4.JUN.8 9:3:55 SPORTON INTERNTIONL INC. Page Number : 44 of 58

45 CSE Plot on Ch 78 between 3MHz ~ 3 GHz * RBW khz SWT 3 ms Marker [T ] dbm.8774 GHz VIEW D 7.9 dbm Marker [T ] 7.9 dbm.483 GHz - D -.8 dbm Start 3 MHz 97 MHz/ Stop 3 GHz Date: 4.JUN.8 9:7:36 CSE Plot on Ch 78 between GHz ~ 5 GHz * RBW khz SWT.3 s Marker [T ] dbm GHz VIEW D 5.66 dbm Marker [T ] 5.66 dbm.46 GHz - D dbm Start GHz.3 GHz/ Stop 5 GHz Date: 4.JUN.8 9:8: SPORTON INTERNTIONL INC. Page Number : 45 of 58

46 Test Mode : 3Mbps Temperature : ~5 Test Channel : Relative Humidity : 5~54% Test Engineer : CSE Plot on Ch between 3MHz ~ 3 GHz Tommy Lee/Luffy Lin * RBW khz SWT 3 ms Marker [T ] dbm.88 GHz VIEW D 5.8 dbm Marker [T ] 5.8 dbm.46 GHz - D -4.9 dbm Start 3 MHz 97 MHz/ Stop 3 GHz Date: 4.JUN.8 9:33:38 CSE Plot on Ch between GHz ~ 5 GHz * RBW khz SWT.3 s Marker [T ] dbm.64 GHz VIEW D 4.89 dbm Marker [T ] 4.89 dbm.368 GHz - D -5. dbm Start GHz.3 GHz/ Stop 5 GHz Date: 4.JUN.8 9:34:5 SPORTON INTERNTIONL INC. Page Number : 46 of 58

47 CSE Plot on Ch 39 between 3MHz ~ 3 GHz * RBW khz SWT 3 ms Marker [T ] dbm GHz VIEW D 6.8 dbm Marker [T ] 6.8 dbm.4464 GHz - D -3. dbm Start 3 MHz 97 MHz/ Stop 3 GHz Date: 4.JUN.8 9:39:3 CSE Plot on Ch 39 between GHz ~ 5 GHz * RBW khz SWT.3 s Marker [T ] dbm 4.77 GHz VIEW D 5.67 dbm Marker [T ] 5.67 dbm.44 GHz - D dbm Start GHz.3 GHz/ Stop 5 GHz Date: 4.JUN.8 9:39:5 SPORTON INTERNTIONL INC. Page Number : 47 of 58

48 CSE Plot on Ch 78 between 3MHz ~ 3 GHz * RBW khz SWT 3 ms Marker [T ] dbm GHz VIEW D 6.5 dbm Marker [T ] 6.5 dbm.483 GHz - D dbm Start 3 MHz 97 MHz/ Stop 3 GHz Date: 4.JUN.8 9:44:39 CSE Plot on Ch 78 between GHz ~ 5 GHz * RBW khz SWT.3 s Marker [T ] dbm 4.74 GHz VIEW D 7.48 dbm Marker [T ] 7.48 dbm.46 GHz - D -.5 dbm Start GHz.3 GHz/ Stop 5 GHz Date: 4.JUN.8 9:46:6 SPORTON INTERNTIONL INC. Page Number : 48 of 58

49 3.8 Radiated Band Edges and Spurious Emission Measurement 3.8. Limit of Radiated Band Edges and Spurious Emission In any khz bandwidth outside the intentional radiator frequency band, all harmonics/spurious must be at least db below the highest emission level within the authorized band. In addition, radiated emissions which fall in the restricted bands must also comply with the limits as below. Frequency (MHz) Field Strength (microvolts/meter) Measurement Distance (meters) /F(kHz) /F(kHz) bove Measuring Instruments The measuring equipment is listed in the section 4 of this test report. SPORTON INTERNTIONL INC. Page Number : 49 of 58

50 3.8.3 Test Procedures. The EUT was placed on a turntable with.8 meter for frequency below GHz and.5 meter for frequency above GHz respectively above ground.. The EUT was set 3 meters from the interference receiving antenna, which was mounted on the top of a variable height antenna tower. 3. For each suspected emission, the EUT was arranged to its worst case and then tune the ntenna tower (from m to 4 m) and turntable (from degree to 36 degrees) to find the maximum reading. pre-amp and a high pass filter are used for the test in order to get better signal level to comply with the guidelines. 4. Set to the maximum power setting and enable the EUT transmit continuously. 5. Use the following spectrum analyzer settings: () Span shall wide enough to fully capture the emission being measured; () Set RBW= khz for f < GHz, RBW=MHz for f>ghz ; VBW RBW; Sweep = auto; Detector function = peak; Trace = max hold for peak (3) For average measurement: use duty cycle correction factor method per 5.35(c). Duty cycle = On time/ milliseconds On time = N *L +N *L +...+N n- *LN n- +N n *L n Where N is number of type pulses, L is length of type pulses, etc. verage Emission Level = Peak Emission Level + *log(duty cycle) 6. Corrected Reading: ntenna Factor + Cable Loss + Read Level - Preamp Factor = Level 7. For testing below GHz, if the emission level of the EUT in peak mode was 3 db lower than the limit specified, then peak values of EUT will be reported, otherwise, the emissions will be repeated one by one using the CISPR quasi-peak method and reported. 8. For testing above GHz, the emission level of the EUT in peak mode was db lower than average limit (that means the emission level in average mode also complies with the limit in average mode), then peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. Note: The average levels were calculated from the peak level corrected with duty cycle correction factor (-4.79dB) derived from log (dwell time/ms). This correction is only for signals that hop with the fundamental signal, such as band-edge and harmonic. Other spurious signals that are independent of the hopping signal would not use this correction. SPORTON INTERNTIONL INC. Page Number : 5 of 58

51 3.8.4 Test Setup For radiated emissions below 3MHz For radiated emissions from 3MHz to GHz For radiated emissions above GHz SPORTON INTERNTIONL INC. Page Number : 5 of 58

52 3.8.5 Test Results of Radiated Spurious Emissions (9 khz ~ 3 MHz) The low frequency, which started from 9 khz to 3MHz, was pre-scanned and the result which was db lower than the limit line was not reported. There is a comparison data of both open-field test site and semi-nechoic chamber, and the result came out very similar Test Result of Radiated Spurious at Band Edges Please refer to ppendix B Test Result of Radiated Spurious Emission (3MHz ~ th Harmonic) Please refer to ppendix B Duty cycle correction factor for average measurement Please refer to ppendix C. SPORTON INTERNTIONL INC. Page Number : 5 of 58

53 3.9 C Conducted Emission Measurement 3.9. Limit of C Conducted Emission For equipment that is designed to be connected to the public utility (C) power line, the radio frequency voltage that is conducted back onto the C power line on any frequency or frequencies within the band 5 khz to 3 MHz shall not exceed the limits in the following table. Frequency of emission (MHz) Quasi-peak Conducted limit (dbμv) verage to 56* 56 to 46* *Decreases with the logarithm of the frequency Measuring Instruments The measuring equipment is listed in the section 4 of this test report Test Procedures. The EUT was placed.4 meter from the conducting wall of the shielding room was kept at least 8 centimeters from any other grounded conducting surface.. Connect EUT to the power mains through a line impedance stabilization network (LISN). 3. ll the support units are connecting to the other LISN. 4. The LISN provides 5 ohm coupling impedance for the measuring instrument. 5. The FCC states that a 5 ohm, 5 microhenry LISN should be used. 6. Both sides of C line were checked for maximum conducted interference. 7. The frequency range from 5 khz to 3 MHz was searched. 8. Set the test-receiver system to Peak Detect Function and specified bandwidth (IF Bandwidth = 9kHz) with Maximum Hold Mode. Then measurement is also conducted by verage Detector and Quasi-Peak Detector Function respectively. SPORTON INTERNTIONL INC. Page Number : 53 of 58

54 3.9.4 Test Setup Test Result of C Conducted Emission Please refer to ppendix B. SPORTON INTERNTIONL INC. Page Number : 54 of 58

55 3. ntenna Requirements 3.. Standard pplicable If directional gain of transmitting antennas is greater than 6dBi, the power shall be reduced by the same level in db comparing to gain minus 6dBi. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the rule. 3.. ntenna nti-replacement Construction n embedded-in antenna design is used ntenna Gain The antenna peak gain of EUT is less than 6 dbi. Therefore, it is not necessary to reduce maximum peak output power limit. SPORTON INTERNTIONL INC. Page Number : 55 of 58

56 4 List of Measuring Equipment Instrument Manufacturer Model No. Serial No. Characteristics Calibration Date Test Date Due Date Remark Hygrometer Testo 68-H N/ Mar. 6, 8 Jun. 4, 8 Mar. 5, 9 Power Meter gilent E446 Power Sensor gilent E937 Spectrum nalyzer BT Base Station (Measure) Rohde & Schwarz Rohde & Schwarz GB US N/ Dec., 7 Jun. 4, 8 Dec. 9, 8 5MHz~8GHz Dec., 7 Jun. 4, 8 Dec. 9, 8 FSP3 67 9kHz ~ 3GHz Nov. 3, 7 Jun. 4, 8 Nov., 8 CBT 36 BT 3. Sep., 7 Jun. 4, 8 Sep. 9, 8 C Power Source ChainTek PC-W N/ N/ NCR May 4, 8 NCR EMI Test Receiver Rohde & Schwarz ESR GHz Dec. 8, 7 May 4, 8 Dec. 7, 8 Hygrometer Testo 68-H N/ Mar. 6, 8 May 4, 8 Mar. 5, 9 LISN LF Cable Pulse Limiter Loop ntenna Bilog ntenna Horn ntenna SHF-EHF Horn ntenna Rohde & Schwarz HUBER + SUHNER Rohde & Schwarz Rohde & Schwarz TESEQ SCHWRZBE CK SCHWRZBE CK ENV6 8 9kHz~3MHz Nov. 3, 7 May 4, 8 Nov. 9, 8 RG-4/U LF N/ Jan. 3, 8 May 4, 8 Jan., 9 ESH3-Z 85 N/ Jan. 3, 8 May 4, 8 Jan., 9 HFH-Z khz~3 MHz Nov. 3, 7 CBL 6D&N-6-6 N6 BBH 9 D 9D-3 6 BBH 97 BBH MHz~GHz Oct. 4, 7 GHz ~ 8GHz Oct. 6, 7 8GHz- 4GHz Nov. 7, 7 mplifier SONOM 3N 873 9kHz~GHz Jan. 6, 8 Preamplifier Jet-Power JP K Preamplifier Keysight 837 mplifier Spectrum nalyzer ntenna Mast MITEQ Keysight EMEC HG N9 3544&T- TT M-BS-45- B 54 MY MY GHz~8GHz pr. 7, 8 GHz~6.5GHz Jan. 6, 8 8GHz~4GHz, VSWR :.5: max Jul. 8, 7 Hz ~ 44GHz Oct. 9, 7 N/ ~4m NCR Turn Table EMEC TT N/ ~36 Degree NCR Controller EMEC EM N/ Control Turn table & nt Mast NCR Jun. 5, 8~ Jun. 6, 8 Jun. 5, 8~ Jun. 6, 8 Jun. 5, 8~ Jun. 6, 8 Jun. 5, 8~ Jun. 6, 8 Jun. 4, 8~ Jun. 6, 8 Jun. 4, 8~ Jun. 6, 8 Jun. 4, 8~ Jun. 6, 8 Jun. 4, 8~ Jun. 6, 8 Jun. 4, 8~ Jun. 6, 8 Jun. 4, 8~ Jun. 6, 8 Jun. 4, 8~ Jun. 6, 8 Jun. 4, 8~ Jun. 6, 8 Nov., 8 Oct. 3, 8 Oct. 5, 8 Nov. 6, 8 Jan. 5, 9 pr. 6, 9 Jan. 5, 9 Jul. 7, 8 Oct. 8, 8 NCR NCR NCR Conducted (TH5-HY) Conducted (TH5-HY) Conducted (TH5-HY) Conducted (TH5-HY) Conducted (TH5-HY) Conduction (CO5-HY) Conduction (CO5-HY) Conduction (CO5-HY) Conduction (CO5-HY) Conduction (CO5-HY) Conduction (CO5-HY) Radiation (3CH-HY) Radiation (3CH-HY) Radiation (3CH-HY) Radiation (3CH-HY) Radiation (3CH-HY) Radiation (3CH-HY) Radiation (3CH-HY) Radiation (3CH-HY) Radiation (3CH-HY) Radiation (3CH-HY) Radiation (3CH-HY) Radiation (3CH-HY) SPORTON INTERNTIONL INC. Page Number : 56 of 58

57 Hygrometer TECPEL DTN-33B TP435 N/ Oct., 7 Jun. 4, 8~ Jun. 6, 8 Oct., 8 Radiation (3CH-HY) RF Cable HUBER + SUHNER SUCOFLEX 4 MY9837/4 9K-3M Mar., 8 Jun. 4, 8~ Jun. 6, 8 Mar. 9, 9 Radiation (3CH-HY) RF Cable HUBER + SUHNER SUCOFLEX 4 MY9837/4 3M-8G Mar. 5, 8 Jun. 4, 8~ Jun. 6, 8 Mar. 4, 9 Radiation (3CH-HY) RF Cable HUBER + SUHNER SUCOFLEX MY589/ 3M-8G Mar. 5, 8 Jun. 4, 8~ Jun. 6, 8 Mar. 4, 9 Radiation (3CH-HY) Filter Wainwright WHKX SS SN3.7G High Pass Sep. 8, 7 Jun. 4, 8~ Jun. 6, 8 Sep. 7, 8 Radiation (3CH-HY) Filter Wainwright WLK S S SN G Low Pass Sep. 8, 7 Jun. 4, 8~ Jun. 6, 8 Sep. 7, 8 Radiation (3CH-HY) NCR: No Calibration Required SPORTON INTERNTIONL INC. Page Number : 57 of 58

58 5 Uncertainty of Evaluation Uncertainty of Conducted Emission Measurement (5 khz ~ 3 MHz) Measuring Uncertainty for a Level of Confidence of 95% (U = Uc(y)).7dB Uncertainty of Radiated Emission Measurement (3 MHz ~ MHz) Measuring Uncertainty for a Level of Confidence of 95% (U = Uc(y)) 5.dB Uncertainty of Radiated Emission Measurement ( MHz ~ 8 MHz) Measuring Uncertainty for a Level of Confidence of 95% (U = Uc(y)) 5.5dB Uncertainty of Radiated Emission Measurement (8 MHz ~ 4 MHz) Measuring Uncertainty for a Level of Confidence of 95% (U = Uc(y)) 5.dB SPORTON INTERNTIONL INC. Page Number : 58 of 58

59 ppendix. C Conducted Emission Test Results Temperature : ~5 Test Engineer : rthur Hsieh Relative Humidity : 5~55% Test Voltage : Vac / 6Hz Phase : Line Full Spectrum Level in dbµv 礦 CISPR-QP Limit at Main Ports CISPR-ve Limit at Main Ports 3 5k M M 3M 4M 5M 6 8 M M 3M Final_Result Frequency (MHz) QuasiPeak (dbµv) Cverage (dbµv) Frequency in Hz Limit (dbµv) Margin (db) Line Filter Corr L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF 9.5 (db) SPORTON INTERNTIONL INC. Page Number : of 4

60 Test Engineer : rthur Hsieh Temperature : ~5 Relative Humidity : 5~55% Test Voltage : Vac / 6Hz Phase : Line Full Spectrum Level in dbµv 礦 CISPR-QP Limit at Main Ports CISPR-ve Limit at Main Ports 3 5k M M 3M 4M 5M 6 8 M M 3M Frequency in Hz Final_Result Frequency (MHz) QuasiPeak (dbµv) Cverage (dbµv) Limit (dbµv) Margin (db) Line Filter Corr. (db) L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF L OFF 9.6 SPORTON INTERNTIONL INC. Page Number : of 4

61 Temperature : ~5 Test Engineer : rthur Hsieh Relative Humidity : 5~55% Test Voltage : Vac / 6Hz Phase : Neutral Full Spectrum Level in dbµv 礦 CISPR-QP Limit at Main Ports CISPR-ve Limit at Main Ports 3 5k M M 3M 4M 5M 6 8 M M 3M Frequency in Hz Final_Result Frequency (MHz) QuasiPeak (dbµv) Cverage (dbµv) Limit (dbµv) Margin (db) Line Filter Corr. (db) N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF 9.5 SPORTON INTERNTIONL INC. Page Number : 3 of 4

62 Temperature : ~5 Test Engineer : rthur Hsieh Relative Humidity : 5~55% Test Voltage : Vac / 6Hz Phase : Neutral Full Spectrum Level in dbµv 礦 CISPR-QP Limit at Main Ports CISPR-ve Limit at Main Ports 3 5k M M 3M 4M 5M 6 8 M M 3M Final_Result Frequency (MHz) QuasiPeak (dbµv) Cverage (dbµv) Frequency in Hz Limit (dbµv) Margin (db) Line Filter Corr N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF N OFF 9.6 (db) SPORTON INTERNTIONL INC. Page Number : 4 of 4

63 ppendix B. Radiated Spurious Emission Test Engineer : Hao Chuan Temperature : ~6 C Relative Humidity : 5~56% SPORTON INTERNTIONL INC. Page Number : B of B7

64 .4GHz 4~483.5MHz BT (Band 3m) BT Note Frequency Level Over Limit Read ntenna Path Preamp nt Table Peak Pol. Limit Line Level Factor Loss Factor Pos Pos vg. ( MHz ) ( dbμv/m ) ( db ) ( dbμv/m ) ( dbμv ) ( db/m ) ( db ) ( db ) ( cm ) ( deg ) (P/) (H/V) P H H BT CH 4MHz * P H * H P V V * P V * V P H H * P H * H BT CH 39 44MHz P H H P V V * P V * V P V V SPORTON INTERNTIONL INC. Page Number : B of B7

65 * P H * H BT CH 78 48MHz P H H * P V * V Remark P V V. No other spurious found.. ll results are PSS against Peak and verage limit line. SPORTON INTERNTIONL INC. Page Number : B3 of B7

66 .4GHz 4~483.5MHz BT 3m) BT Note Frequency Level Over Limit Read ntenna Path Preamp nt Table Peak Pol. BT CH 4MHz Limit Line Level Factor Loss Factor Pos Pos vg. ( MHz ) ( dbμv/m ) ( db ) ( dbμv/m ) ( dbμv ) ( db/m ) ( db ) ( db ) ( cm ) ( deg ) (P/) (H/V) P H H P V V P H H BT CH 39 44MHz P H H P V V P V V P H H BT CH 78 48MHz P H H P V V Remark P V V. No other spurious found.. ll results are PSS against Peak and verage limit line. SPORTON INTERNTIONL INC. Page Number : B4 of B7

67 Emission below GHz.4GHz BT (LF) BT Note Frequency Level Over Limit Read ntenna Path Preamp nt Table Peak Pol. Limit Line Level Factor Loss Factor Pos Pos vg. ( MHz ) ( dbμv/m ) ( db ) ( dbμv/m ) (dbμv) ( db/m ) ( db ) ( db ) ( cm ) ( deg ) (P/) (H/V) P H P H P H P H.4GHz BT LF P H P H P V P V Remark P V P V P V P V. No other spurious found.. ll results are PSS against limit line. SPORTON INTERNTIONL INC. Page Number : B5 of B7

68 Note symbol Fundamental Frequency which can be ignored. However, the level of any * unwanted emissions shall not exceed the level of the fundamental frequency.! Test result is over limit line. P/ Peak or verage H/V Horizontal or Vertical SPORTON INTERNTIONL INC. Page Number : B6 of B7

69 calculation example for radiated spurious emission is shown as below: BT Note Frequency Level Over Limit Read ntenna Path Preamp nt Table Peak Pol. Limit Line Level Factor Loss Factor Pos Pos vg. ( MHz ) ( dbμv/m ) ( db ) ( dbμv/m ) ( dbμv ) ( db/m ) ( db ) ( db ) ( cm ) ( deg ) (P/) (H/V) BT CH 4MHz P H H. Path Loss(dB) = Cable loss(db) + Filter loss(db) + ttenuator loss(db). Level(dBμV/m) = ntenna Factor(dB/m) + Path Loss(dB) + Read Level(dBμV) - Preamp Factor(dB) 3. Over Limit(dB) = Level(dBμV/m) Limit Line(dBμV/m) For Peak 39MHz:. Level(dBμV/m) = ntenna Factor(dB/m) + Path Loss(dB) + Read Level(dBμV) - Preamp Factor(dB) = 3.(dB/m) (dB) (dBμV) (db) = (dbμv/m). Over Limit(dB) = Level(dBμV/m) Limit Line(dBμV/m) = 55.45(dBμV/m) 74(dBμV/m) = -8.55(dB) For verage 39MHz:. Level(dBμV/m) = ntenna Factor(dB/m) + Path Loss(dB) + Read Level(dBμV) - Preamp Factor(dB) = 3.(dB/m) (dB) + 4.6(dBμV) (db) = (dbμv/m). Over Limit(dB) = Level(dBμV/m) Limit Line(dBμV/m) = 43.54(dBμV/m) 54(dBμV/m) = -.46(dB) Both peak and average measured complies with the limit line, so test result is PSS. SPORTON INTERNTIONL INC. Page Number : B7 of B7

70 Report No. : FR8468- ppendix C. Duty Cycle Plots DH5 on time (One Pulse) Plot on Channel 39 DH5 on time (Count Pulses) Plot on Channel 39 Note:. Worst case Duty cycle = on time/ milliseconds = *.88 / = 5.76 %. Worst case Duty cycle correction factor = *log(duty cycle) = db 3. DH5 has the highest duty cycle worst case and is reported. SPORTON INTERNTIONL INC. Page Number : C of C