Magnetism & Microwave Setup 1 Magnetism (and Microwave) Magnetism & Microwave Setup 2 Magnetism (and Microwave)

Transcription

1 Equipment List Anechoic_chamber Anechoic Chamber Fully anechoic chamber 400 MHz-40 GHz. Shielding effectiveness: > 65 10kHz > 120 1MHz > 140 1GHz > 90dB@ 40GHz Reflectivity performances of absorbers: MHz GHz GHz and beyond External dimensions 600x500x350 cm Internal dimensions 469x360x221 cm Wall panel with waveguides for Fiber optics N, 3,5mm, 2.92mm coax through bulkhead connectors Power line filter & isolation transformer Turntable 2 axis Magnetism & Microwave Setup 1 Magnetism (and Microwave) Setup 1 Short description below - Fug Low voltage power supplies, power class > 4200W Type NTM M-260 Magnetism & Microwave Setup 2 Magnetism (and Microwave) Setup 2 Short description below NearField Probe Agilent 11945A Near-field probe plus petit que span>the Keysight 11945A close-field probe set includes both the 11940A and 11941A probes to provide full coverage from 9 khz to 1 GHz. This set provides a powerful measurement tool for electrical and mechanical designers who want to search for and eliminate sources of interference from their products early in the design process. plus petit que /span> NearField probe R&S HZ-14 Near-field probe Rohde & Schwarz HZ-14 Probe Set for E and H Near-Field Measurements (9kHz-1GHz)

2 NearField Probe R&S HZ-15 Near-field probe Rohde & Schwarz HZ-15 Probe Set for E and H Near-Field Measurements (30 MHz-3 GHz) HP 437B PowerMeter Power meter 437B High Performance Single Channel Average Power Meter. The Agilent 437B power meter is a low-cost, high-performance, single-channel, programmable, average power meter compatible with the 8480 family of power sensors. Depending on which power sensor is used, the 437B can measure from -70 dbm (100pW) to +44 dbm (25W) at frequencies from 100 khz to 110 GHz. Features - Power reference for automatic calibration and zeroing ; - Duty cycle entry for a convenient peak power representation of the measurement average power ; - Ten preloaded sensor card factors versus frequency ; - Frequency Range: 100 khz to 110 GHz(50 GHZ with our Power Sensor). U2000B PowerMeter Power meter Agilent U2000B USB Power Sensor 10 MHz-18 GHz, -30 to + 44 dbm(1µw-25w) opt : 100 Elektrobit_Channel Sounder Elektrobit Propsound CS MIMO channel sounder, GHz, 200 MHz bandwidth and up to 8 x 8 antennas. Includes post-processing software with high-resolution algorithm for double-directional analysis. NI_USRP 2017 Set of 4 NI USRP-2944R, 160 MHZ BW, 10 MHz to 6 GHZ SDR Accessories : 16 Vertical Antenna 8 Channel Clock Distribution 1U Rack mount PCIe-MXI Express interface GPIO Connection kit

3 NI_USRP_1 Software Radio Educational Lab Station : Two NI USRP-2920 Bundles with Lab Materials are designed for wireless communications teaching and research. National Instruments combines the power of NI LabVIEW software and USRP hardware to deliver an affordable and easy-to-use software-reconfigurable RF platform that works well for communications education, experimentation, research, and rapid prototyping. With wide frequency coverage and two RF configurations, the NI USRP platform helps you experiment and prototype physical layer host-based algorithms with live signals in the same bands as a/b/g/n and ZigBee. This functionality both enhances the depth of an educational experience and allows researchers to rapidly validate their work with real-world data. NI_USRP_2 Software Radio Educational Lab Station : Two NI USRP-2920 Bundles with Lab Materials are designed for wireless communications teaching and research. National Instruments combines the power of NI LabVIEW software and USRP hardware to deliver an affordable and easy-to-use software-reconfigurable RF platform that works well for communications education, experimentation, research, and rapid prototyping. With wide frequency coverage and two RF configurations, the NI USRP platform helps you experiment and prototype physical layer host-based algorithms with live signals in the same bands as a/b/g/n and ZigBee. This functionality both enhances the depth of an educational experience and allows researchers to rapidly validate their work with real-world data. NI_USRP_3 Software Radio Educational Lab Station : Two NI USRP-2920 Bundles with Lab Materials are designed for wireless communications teaching and research. National Instruments combines the power of NI LabVIEW software and USRP hardware to deliver an affordable and easy-to-use software-reconfigurable RF platform that works well for communications education, experimentation, research, and rapid prototyping. With wide frequency coverage and two RF configurations, the NI USRP platform helps you experiment and prototype physical layer host-based algorithms with live signals in the same bands as a/b/g/n and ZigBee. This functionality both enhances the depth of an educational experience and allows researchers to rapidly validate their work with real-world data.

4 NI_USRP_4 Software Radio Educational Lab Station : Two NI USRP-2920 Bundles with Lab Materials are designed for wireless communications teaching and research. National Instruments combines the power of NI LabVIEW software and USRP hardware to deliver an affordable and easy-to-use software-reconfigurable RF platform that works well for communications education, experimentation, research, and rapid prototyping. With wide frequency coverage and two RF configurations, the NI USRP platform helps you experiment and prototype physical layer host-based algorithms with live signals in the same bands as a/b/g/n and ZigBee. This functionality both enhances the depth of an educational experience and allows researchers to rapidly validate their work with real-world data. Radar K-DT1 RF Beam K-DT1 Hanheld Doppler Target. Handheld Doppler Simulator - Fully Standalone 1 to 300 km/h Simulation - 3 Presets Adjustable Amplitude, Direction, Duration Powerful PC Software plus petit que div> Qty. 2plus petit que /div> Radar K-MD2 plus petit que span class="product-subtitle">rf Beam Radar Transceiver Key Features:plus petit que /span> plus petit que div class="product-features"> - 24GHz FMCW Radar with Digital Signal Processing Monopulse in Azimuth / Elevation - Serial Target List Output - Detection Distance: 100m for persons/200m for cars - Distance range:0..255m, 1m resolution - Speed range:±150km/h, 1km/h resolution - Angle range:±10 (Elevation) ±15 (Azimuth), 0.1 resolution - Compact size: mm plus petit que /div> 56100A Scalar network analyzer Scalar Network Analyzer 56100A - Full compatibility with Anritsu sources - 10 MHz to 50 GHz - Four input channels - Extensive cursor, markers, and limit lines - Applications functions for improved productivity.

5 N9000A Spectrum analyzer N9000A CXA Signal Analyzer Functionality * 9 khz to 3.0 or 7.5 GHz * Standards-based PowerSuite: channel power, OBW, ACP, CCDF, SEM, TOI, Harmonics * Basic EMI precompliance measurement capability available, including CISPR bandwidths, detectors, amplitude correction factor, band preset, tune & listen at marker, and limit lines Performance * ±0.5 db absolute amplitude accuracy * +13 dbm third order intercept (TOI) * -145 dbm displayed average noise level (DANL) * -66 db W-CDMA ACLR dynamic range (with noise correction on) Measurement Application & Software * Analog demodulation, noise figure, EMC, W-CDMA, TD-SCDMA, Bluetooth, digital video and more. View full list of measurement applications * Advanced analysis of up to 70 signal formats, software runs inside the CXA VSA software * MATLAB data analysis software for general purpose data analysis, visualization, and measurement automation. MATLAB Software for X-Series Automation & Communication Interface * LXI class C compliant, SCPI, and IVI-COM * USB 2.0, 100Base-T LAN, GPIB * Programming remote language compatibility with ESA and other X-Series * Common X-Series user interface / Open Windows XP operating system Spectrum MS2713E Spectrum analyzer Anritsu MS2713E Compact Handheld Spectrum Analyzer plus petit que span style="white-space: pre;"> plus petit que /span>- Freq range : 9 khz to 6 GHz - Dynamic range : Hz RBW - DANL : Hz RBW - Electromagnetic Field Measurements(option 444) with our Isotropic antenna R (700 MHz-6 GHz). Spectrum PSA E4440A Spectrum analyzer The Agilent PSA E4440A offer high-performance spectrum analysis up to 26.5 GHz and beyond with powerful one-button measurements, a versatile feature set, and a leading-edge combination of flexibility, speed, accuracy, and dynamic range. Noise Figure and Phase Noise Personalities. Installed options : 1DS/219/226/AYZ/B7J/H70. Spectrum U3661 Spectrum analyzer Advantest U3661 Microwave Spectrum Analyzer 9 khz-26.5 GHz Installed options : - 20 : High Stability reference oscillator - 26 : Adds 100 Hz & 300 Hz RBW

6 Anritsu 68377C Anritsu Synthesized CW Generators These basic signal sources provide accurate outputs over a wide frequency and power range for Local Oscillator duty and other CW applications. Broad frequency coverage including 10 MHz to 50 GHz in a single coax output. Ultra-low SSB phase noise and spurious +17 dbm guaranteed leveled power to 20 GHz. 0.1 Hz optional frequency resolution <5 ms switching time for <100 MHz sweep steps. Digital frequency sweep and digital power sweep Wide dynamic range with accurate output levels. Synthe 20 GHz MXG N5183B Keysight N5183B MXG X-Series Microwave Analog Signal Generator * 9 khz to 20 GHz * -130 dbm to +23 dbmplus petit que span style="white-space: pre;"> plus petit que /span> Synthe 3 GHz MXG N5181A Agilent N5181A MXG Analog Signal Generator Signal characteristics khz to 3 GHz dbm output 1 GHz dbc/hz (typ) phase noise at 1 GHz and 20 khz offset 1.2 ms switching speed in SCPI mode; 900 μs simultaneous frequency and amplitude switching in list mode Modulation and sweep AM, FM, ØM, and pulse modulation - Digital step and list sweep with simultaneous switching of frequency and power Automation and communication interface - 100BaseT LAN, USB 2.0 and GPIB - LXI compliant - SCPI and IVI-COM drivers - Backwards compatible with all ESG, PSG, 8648 signal generators, and other vendors' signal generators Synthe 40GHz anritsu 68067C Anritsu 68067C Synthesized CW Generator plus petit que span style="white-space: pre;"> plus petit que /span>0,01 to 40 GHz Synthe Fluke 6062A The 6062A Synthesized RF Signal Generators covers the frequency range of 100kHz to 2.1GHz in 20Hz steps (10Hz steps below 1050MHz). Specified amplitude accuracy is ±1.5 db from -127 dbm to +13 dbm. The unit has amplitude and frequency modulation as well as phase and fast-rise pulse modulation. The instruments gallium arsenide pulse modulator generates fast, high quality pulses for testing of pulsed communication and navigation circuits. It employs a design that can generate very narrow pulses, limited only by the modulator's 15 ns rise and fall time. IEEE 488 interface is standard Frequency Range 100 khz GHz Frequency Resolution 20 Hz Output Accuracy +/- 1.0 db Output Range -137 dbm dbm Output Resolution.1 db Programmable Interface -54 dbc/hz SSB Phase Noise Range HP-IB dbc/hz Time Base Stability +/-.5 ppm

7 Synthe PSG E8267D Most advanced microwave signal generator E8267D PSG vector signal generator is the first integrated microwave vector signal generator with I/Q modulation up to 20 GHz. It features an advanced wideband internal baseband generator capable of flexible arbitrary waveform playback or sophisticated real-time signal generation. The E8267D PSG also has a built-in wideband I/Q modulator that delivers up to 2 GHz RF modulation bandwidth and is a perfect complement to Agilent's N6030A stand-alone wideband arbitrary waveform generator for I/Q waveform simulations up to 1 GHz RF bandwidth. This groundbreaking integrated vector functionality, only available in the E8267D PSG, drastically simplifies the generation of complex modulated signals for design and manufacturing test applications in aerospace, defense, satellite communications, and broadband wireless Synthe Wiltron 6769B Wiltron 6769B. Synthesized sweeper. 10MHz to 40GHz frequency range, +10dBm output power, 25ms switching speed over any frequency step size, 1kHz resolution, simultaneous fm, am and pulse modulation, gpib, lcd display of frequency, modulation, and level.!!! Work now only from 2 GHz!!! VNA 37369A 40 GHz Anritsu 37369A Vector Network Analyzer, 40 MHz to 40 GHz The 37369A network analyzer integrates a synthesized source, S-parameter test set and tuned receiver into a single compact package that is ideal for bench-top testing. It provides: 40 MHz to 40 GHz; Fast Sweeping Synthesized Source; Auto Reversing Test Set; Solid-State Transfer Switch; Four Independent Displays; Four Channel Receiver; Internal Hard and Floppy Disk Drives; LRL/LRM Calibration; Adapter Removal Calibrations; Fast Measurement Throughput via GPIB.

8 VNA ENA E5061B 3GHz E5061B responds to various measurement needs, from LF to RF. The Agilent E5061B is a member of the ENA Series network analyzers. The E5061B addresses a broad range of measurement needs of electronic components and circuits from low to high frequencies. The E5061B now provides a new standard of frequency-domain device analysis from 5 Hz to 3 GHz. LF-RF NA Option: E5061B-3L5 Comprehensive LF-to-RF network analysis. The E5061B-3L5 LF-RF NA option offers versatile network analysis in the broad frequency range from 5 Hz to 3 GHz. Comprehensive LF network measurement capabilities including built-in 1 MO inputs have been seamlessly integrated with the high-performance RF network analyzer. The E5061B-3L5 is the right solution for component and circuit evaluations in the R&D environment. Key Features & Specifications RF-NA option 100 khz to 1.5 GHz / 3 GHz Transmission / Reflection test set and S-parameter test set 50 Ohms and 75 Ohms system impedance LF-RF NA option 5 Hz to 3 GHz 50 Ohms S-parameter test set Gain-phase test port (1 MO / 50 Ohms inputs) DC-bias source Impedance analysis function (option 005)!!! Not yet available at UCL-WELCOME!!! VNA FieldFox 18 GHz Keysight N9917A 18 GHz Fieldfox Microwave Analyzer Cable & Antenna Analyzer plus petit que span style="white-space: pre;"> plus petit que /span>option 210 : VNA transmission/reflection plus petit que span style="white-space: pre;"> plus petit que /span>option 211 : VNA full 2-port S-parameters VNA HP 4195 The 4195A Network/Spectrum analyzer provides excellent vector network and spectrum measurement performance from 10 Hz to 500 MHz. Providing both vector network and spectrum measurement capabilities, the 4195A is a cost effective solution for the development and production testing of analog devices. For improved performance and simple operation, many new and powerful features have been included, thus making the 4195A an ideal tool for the analog design engineer. In addition to measuring a complete set of network and spectrum parameters, the 4195A can automatically derive impedance parameters from S-parameters. Direct impedance measurements from 100 khz to 500 MHz can be performed using the optional 41951A Impedance test kit.

9 VNA HP8753C HP 8753C & test set Options : Features & Specifications - Measures reflection and transmission characteristics of two-port devices in either direction with a single connection. - Includes a frequency doubler that can be switched in to measure 3 MHz to 6 GHz in a single sweep - Full frequency range of 300 khz to 6 GHz is available for 8753D/E/ES and selected 8702 configurations - Exhibits <5 db insertion loss between the RF input and the test ports - 15 dbm at the test port - Includes a programmable step attenuator VNA MS4644B 40 GHz Anritsu MS4644B Vector Network Analyzer plus petit que span style="white-space: pre;"> plus petit que /span>- 10 MHz-40 GHz plus petit que span style="white-space: pre;"> plus petit que /span>- 2-Ports VNA N5291A 120 GHz Keysight N5291A - Single Sweep 900Hz-120 GHz PNA - 2 Ports - Dynamic range >110 db Output Power max 6 dbm - THz ready VNA PNA-X 26.5GHz The Agilent N5242A premier-performance network analyzer is a member of the PNA Series network analyzer platform and provides highly integrated measurement capabilities for active device tests. * Integrated 4 test ports, balanced measurements ; * 130 db dynamic range, 32 channels, 16,001 points ; * Second internal source for fast measurements of amplifier intermodulation distortion and mixer/converter conversion loss. Up to 35 times faster than using traditional external sources ; * Combining network for simplified two-tone measurements ; * internal modulators and generators for fast, simplified pulsed measurements. Up to 30 times faster than using external modulators and generators ; * Rear panel access loops and internal switches for signal conditioning or single-connection multiple measurements. Options : 080/400/419/423 VNA PNA-X 70GHz N5247A PNA-X 67(70) GHz Key Features & Specifications 10 MHz to 67(70) GHz 2- or with two built-in sources Enables 4-port 110 GHz single-sweep solution (option) 110 db system dynamic range, 32,001 points, 32 channels, 5 MHz IF bandwidth High output power (+10 dbm at 67 GHz) and a wide power sweep range (40 db) 0.1 db receiver compression of +11 dbm at 67 GHz With the support of : plus petit que img style="vertical-align: baseline;" src=" alt="" width="200" height="141" />

10 Site Web : Contact : info-welcome@uclouvain.be VNA ZVR 4GHz Vector Network Analyzer. 10 Hz to 4 GHz.