SOUTH AFRICAN NATIONAL STANDARD
|
|
- Winfred Kelly
- 5 years ago
- Views:
Transcription
1 ISBN SOUTH AFRICAN NATIONAL STANDARD Watt-hour meters AC electronic meters for active energy WARNING Front-end specification. Can only be read in conjunction with SANS :2003 and SANS :2003. Amdt 1 Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001 Tel: Fax: SABS
2 Table of changes Change No. Date Scope Amdt Amended to update the normative reference clause and referenced standards, to update a referenced Act, to delete the modifications for electrostatic discharges and the fast transient burst test, to clarify the requirements for meters in a 230 V nominal system, and to delete the reference to the proof of compliance. Amdt Amended to update the reference to the basic guideline for acceptance tests and to move references to legislation to the foreword. Foreword This South African standard was approved by National Committee SABS/TC 062, Electrical energy measurement and control, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This document was approved for publication in November This document cancels and replaces SANS 1799:2004 (edition 1.1). A vertical line in the margin shows where the text has been technically modified by amendment No. 2. Reference is made in to "the relevant national legislation". In South Africa this means the Telecommunications Act, 1996 (Act No. 103 of 1996). Amdt 2 Reference is made in annex B to "the Regulations of the relevant national legislation". In South Africa this means the Electrical Installation Regulations of the Occupational Health and Safety Act, 1993 (Act No. 85 of 1993). Amdt 2 Annexes A and B are for information only.
3 Contents Page Foreword 1 Scope Normative references Definitions Requirements Modifications... 4 Annex A (informative) Notes to purchasers... 6 Annex B (informative) The application of SANS to electricity meters... 7 Amdt 1 Bibliography
4 This page is intentionally left blank 2
5 Watt-hour meters AC electronic meters for active energy 1 Scope 1.1 This standard specifies requirements for newly manufactured static watt-hour meters of accuracy classes 1 and 2, for the measurement of alternating current (a.c.) electrical active energy of frequencies in the range 45 Hz to 65 Hz, and for their type tests. 1.2 It is applicable only to static watt-hour meters for indoor and outdoor use and that consist of a measuring element and one or more registers enclosed together in a meter case, and also to operation indicators and test outputs. 1.3 Where the display or one or more memories (or any combination of these) is/are external, or where other elements are enclosed in the meter case (such as maximum demand indicators, a telemetering section, time switches or remote controls), this standard is applicable to the metering section only. 1.4 This standard is not applicable to a) watt-hour meters where the voltage across the connection terminals exceeds 600 V (line-to-line voltage for meters for polyphase systems), b) portable meters, c) data interfaces to the register of the meter, d) acceptance tests and routine tests, and e) reliability, since no short-term test procedures are available that could be incorporated in type test documents to check this requirement satisfactorily. NOTE A basic guideline for acceptance tests is given in SANS and SANS Amdt 2 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this standard. All standards are subject to revision and, since any reference to a standard is deemed to be a reference to the latest edition of that standard, parties to agreements based on this standard are encouraged to take steps to ensure the use of the most recent editions of the standards indicated below. Information on currently valid national and international standards can be obtained from the SABS Standards Division. SANS 222/CISPR 22, Information technology equipment Radio disturbance characteristics Limits and methods of measurement. 3
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-27370-5 SOUTH AFRICAN NATIONAL STANDARD Precast concrete manhole sections and components Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-26895-4 Any reference to SABS 142 is deemed to be a reference to this standard (Government Notice No. 1373 of 8 November 2002) SOUTH AFRICAN NATIONAL STANDARD Narrow elastic fabrics and
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 0-626-17358-2 Any reference to SABS 945-1 is deemed to be a reference to this standard (Government Notice No. 1373 of 8 November 2002) SOUTH AFRICAN NATIONAL STANDARD Support and compression bandages
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-34338-5 IEC 60060-3:2006 SOUTH AFRICAN NATIONAL STANDARD High-voltage test techniques Part 3: Definitions and requirements for on-site testing This national standard is the identical implementation
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-33821-3 Edition 2 IEC 60060-2:2010 Edition 3 SOUTH AFRICAN NATIONAL STANDARD High-voltage test techniques Part 2: Measuring systems This national standard is the identical implementation
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-30950-3 SOUTH AFRICAN NATIONAL STANDARD Electromagnetic compatibility (EMC) Part 4-30: Testing and measurement techniques Power quality measurement methods This national standard is the
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-36319-2 Edition 2 IEC 60060-1:2010 Edition 3 SOUTH AFRICAN NATIONAL STANDARD High-voltage test techniques Part 1: General definitions and test requirements This national standard is the
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-22847-7 Any reference to SABS 0155 is deemed to be a reference to this standard (Government Notice No. 1373 of 8 November 2002) SOUTH AFRICAN NATIONAL STANDARD Accuracy in buildings Published
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-32783-5 SOUTH AFRICAN NATIONAL STANDARD Performance requirements for retail textiles Part 3: Piece-goods for men s and boys wear Published by SABS Standards Division 1 Dr Lategan Road Groenkloof
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-28950-8 Any reference to SABS 098-1 is deemed to be a reference to this standard (Government Notice No. 1373 of 8 November 2002) SOUTH AFRICAN NATIONAL STANDARD Public lighting Part 1: The
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-29819-7 ISO/IEC 19794-2:2011 SOUTH AFRICAN NATIONAL STANDARD Information technology Biometric data interchange formats Part 2: Finger minutiae data This national standard is the identical
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-31456-9 IEC 61000-4-8:2009 SOUTH AFRICAN NATIONAL STANDARD Electromagnetic compatibility (EMC) Part 4-8: Testing and measurement techniques Power frequency magnetic field immunity test This
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-21567-5 SOUTH AFRICAN NATIONAL STANDARD Lights for motor vehicles Part 1: Incandescent lamps Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-30579-6 Edition 2 EN 300 296-2:2013 Edition V1.4.1 SOUTH AFRICAN NATIONAL STANDARD Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-31015-8 Edition 1 TR 101 953-2-1:2003 Edition V1.1.1 SOUTH AFRICAN NATIONAL STANDARD Access network xdsl transmission filters Part 2-1: VDSL splitters for European deployment Specification
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-32050-8 Edition 4 IEC 60034-1:2010 Edition 12 SOUTH AFRICAN NATIONAL STANDARD Rotating electrical machines Part 1: Rating and performance This national standard is the identical implementation
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-29792-3 IEC 60076-3:2013 SOUTH AFRICAN NATIONAL STANDARD Power transformers Part 3: Insulation levels, dielectric tests and external clearances in air This national standard is the identical
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-32956-3 Edition 1 ETSI EN 300 639:2001 Edition V1.3.1 SOUTH AFRICAN NATIONAL STANDARD Fixed Radio Systems; Point-to-point equipment; Sub-STM-1 digital radio systems operating in the 13 GHz,
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-19721-6 ISO 1101:2004 SOUTH AFRICAN NATIONAL STANDARD Engineering drawing Part 2: Geometrical tolerancing Section 1: Tolerancing of form, orientation, location and run-out Generalities,
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-32741-5 IEC 61000-4-9:2001 SOUTH AFRICAN NATIONAL STANDARD Electromagnetic compatibility (EMC) Part 4-9: Testing and measurement techniques Pulse magnetic field immunity test This national
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-32929-7 Edition 2 CISPR 20:2006 Edition 6 SOUTH AFRICAN NATIONAL STANDARD Sound and television broadcast receivers and associated equipment Immunity characteristics Limits and methods of
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-27269-2 Edition 1 and nat. amdt 1 ISO 7211-2:1984 Edition 1 Any reference to SABS ISO 7211-2 is deemed to be a reference to this standard (Government Notice No. 1373 of 8 November 2002)
More informationAustralian Standard. Electricity metering equipment (AC) Particular requirements
AS 62053.21 2005 AS 62053.21 2005 Australian Standard Electricity metering equipment (AC) Particular requirements Part 21: Static meters for active energy (classes 1 and 2) (IEC 62053-21, Ed.1.0 (2003)
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-24222-0 Edition 3 ISO 898-1:2009 Edition 4 SOUTH AFRICAN NATIONAL STANDARD Fasteners Part 5: General requirements and mechanical properties Section 1: Mechanical properties of fasteners
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 9780626306380 Edition 1 and nat. amdt 1 ISO 2904:1977 Edition 1 Any reference to SABS 1700217 is deemed to be a reference to this standard (Government Notice No. 1373 of 8 November 2002) SOUTH AFRIAN
More informationCollection of standards in electronic format (PDF) 1. Copyright
Collection of standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance
More informationElectricity metering Payment metering systems Part 41: Standard Transfer Specification
IEC/PAS 62055-41 Edition 1.0 2003-09 Electricity metering Payment metering systems Part 41: Standard Transfer Specification PUBLICLY AVAILABLE SPECIFICATION INTERNATIONAL ELECTROTECHNICAL COMMISSION Reference
More informationSOUTH AFRICAN NATIONAL STANDARD
ICS 21.060.20 ISBN 0-626-15095-7 SANS 1700-14-11:2003 ISO 7417:1984 SOUTH AFRICAN NATIONAL STANDARD Fasteners Part 14: Hexagon nuts Section 11: Hexagon nuts for structural bolting Style 2, hot-dip galvanized
More informationSANS 3001-BSM3:201X Edition 1
ISBN 978-0-626-XXXXXX SANS 3001-BSM3:201X SOUTH AFRICAN NATIONAL STANDARD Civil engineering test methods Part BSM3: Vibratory hammer compaction of test specimens of bitumen stabilized material WARNING
More informationAustralian Standard. Electricity metering equipment (AC) Particular requirements. Part 22: Static meters for active energy (classes 0.2 S and 0.
AS 62053.22 2005 IEC 62053-22, Ed.1.0 (2003) AS 62053.22 2005 Australian Standard Electricity metering equipment (AC) Particular requirements Part 22: Static meters for active energy (classes 0.2 S and
More informationGRID INTERCONNECTION OF EMBEDDED GENERATION. Part 2: Small-scale embedded generation
ISBN 978-0-626-29938-5 NRS 097-2-3:2014 Edition 1 GRID INTERCONNECTION OF EMBEDDED GENERATION Part 2: Small-scale embedded generation Section 3: Simplified utility connection criteria for low-voltage connected
More informationThis is a preview - click here to buy the full publication
CONSOLIDATED VERSION CISPR TR 16-4-4 Edition 2.1 2017-06 colour inside INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE Specification for radio disturbance and immunity measuring apparatus and methods
More informationCKS 440* *This standard references other standards Edition CKS. Coffins and caskets CKS 440 ICS ISBN
ICS 55.160 ISBN 0-626-09381-3 CKS 440* *This standard references other standards Edition 2 1993 CKS Coffins and caskets Published by THE SOUTH AFRICAN BUREAU OF STANDARDS Gr 6 Notice This specification
More informationETSI EN V1.1.1 ( )
EN 300 471-2 V1.1.1 (2001-05) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Rules for Access and
More informationINTERNATIONAL. High-voltage test techniques Partial discharge measurements
INTERNATIONAL STANDARD IEC 60270 Third edition 2000-12 High-voltage test techniques Partial discharge measurements This English-language version is derived from the original bilingual publication by leaving
More informationThis document is a preview generated by EVS
TECHNICAL REPORT CLC/TR 50579 RAPPORT TECHNIQUE TECHNISCHER BERICHT June 2012 ICS 91.140.50 English version Electricity metering equipment (a.c.) - Severity levels, immunity requirements and test methods
More informationFINAL DRAFT TECHNICAL REPORT CLC/FprTR RAPPORT TECHNIQUE TECHNISCHER BERICHT January English version
FINAL DRAFT TECHNICAL REPORT CLC/FprTR 50579 RAPPORT TECHNIQUE TECHNISCHER BERICHT January 2012 ICS English version Electricity metering equipment - Severity levels, immunity requirements and test methods
More informationINTERNATIONAL ELECTROTECHNICAL COMMISSION INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
INTERNATIONAL ELECTROTECHNICAL COMMISSION CISPR 14-1 Edition 4.2 2002-10 Edition 4:2000 consolidated with amendments 1:2001 and 2:2002 INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE Electromagnetic
More informationETSI EN V1.2.1 ( )
EN 300 132-3 V1.2.1 (2003-08) European Standard (Telecommunications series) Environmental Engineering (EE); Power supply interface at the input to telecommunications equipment; Part 3: Operated by rectified
More informationPackaging Complete, filled transport packages and unit loads Dimensions of rigid rectangular packages
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 3394 Third edition 2012-11-01 Packaging Complete, filled transport packages and unit loads Dimensions of rigid rectangular packages Emballages
More informationAustralian Standard. Electricity metering equipment (ac) Particular requirements. Part 23: Static meters for reactive energy (classes 2 and 3)
AS 62053.23 2006 IEC 62053-23, Ed.1.0 (2003) AS 62053.23 2006 Australian Standard Electricity metering equipment (ac) Particular requirements Part 23: Static meters for reactive energy (classes 2 and 3)
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 128-30 First edition 2001-04-01 Technical drawings General principles of presentation Part 30: Basic conventions for views Dessins techniques Principes généraux de représentation
More informationHuman response to vibration Measuring instrumentation. Part 1: General purpose vibration meters
INTERNATIONAL STANDARD ISO 8041-1 First edition 2017-05 Human response to vibration Measuring instrumentation Part 1: General purpose vibration meters Réponse des individus aux vibrations Appareillage
More informationDRAFT SOUTH AFRICAN STANDARD (DSS): PUBLIC ENQUIRY STAGE
DRAFT SOUTH AFRICAN STANDARD (DSS): PUBLIC ENQUIRY STAGE Document number 61/60034-22/2 Reference SANS 60034-22 Date of circulation 2009-12-08 Closing date 2010-01-08 Number and title: SANS 60034-22, Rotating
More informationETSI EN V2.1.1 ( ) Harmonized European Standard (Telecommunications series)
EN 302 500-2 V2.1.1 (2010-10) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) using Ultra WideBand (UWB)
More informationDRAFT SOUTH AFRICAN STANDARD (DSS): PUBLIC ENQUIRY STAGE FOR INTERNATIONAL STANDARD ADOPTION
DRAFT SOUTH AFRICAN STANDARD (DSS): PUBLIC ENQUIRY STAGE FOR INTERNATIONAL STANDARD ADOPTION Document number 022/SANS 20038 Reference SANS 20038 Date of circulation 2017-09-14 Closing date 2017-11-15 Number
More informationSANS 1339:2010 Electric cables Cross-linked polyethylene (XLPE) insulated cables for rated voltages 3,8/6,6 kv to 19/33 kv
DRAFT SOUTH AFRICAN STANDARD (DSS): PUBLIC ENQUIRY STAGE Document number: 66/1339/4 Reference: SANS 1339 Date of circulation: 2009-12-08 Closing date: 2010-02-08 Number and title: SANS 1339:2010 Electric
More informationHuman response to vibration Measuring instrumentation. Part 1: General purpose vibration meters
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 8041-1 First edition 2017-05 Human response to vibration Measuring instrumentation Part 1: General purpose vibration meters Réponse des individus
More informationETSI EN V1.2.1 ( )
EN 300 113-2 V1.2.1 (2002-04) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended
More informationAS/NZS CISPR 14.2:2015
AS/NZS CISPR 14.2:2015 (CISPR 14-2, Ed. 2.0:2015, IDT) Australian/New Zealand Standard Electromagnetic compatibility Requirements for household appliances, electric tools and similar apparatus Part 2:
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60728-1 Third edition 2001-11 Cabled distribution systems for television and sound signals Part 1: Methods of measurement and system performance IEC 2001 Copyright - all rights
More informationThis document is a preview generated by EVS
CONSOLIDATED VERSION CISPR TR 16-4-4 Edition 2.1 2017-06 colour inside INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE Specification for radio disturbance and immunity measuring apparatus and methods
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 8124-2 Third edition 2014-08-15 Safety of toys Part 2: Flammability Sécurité des jouets Partie 2: Inflammabilité Reference number ISO 2014 COPYRIGHT PROTECTED DOCUMENT ISO 2014
More informationETSI EN V1.1.1 ( )
EN 300 220-4 V1.1.1 (2017-02) HARMONISED EUROPEAN STANDARD Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 4: Harmonised Standard covering the essential requirements
More informationEMC Test Report. Report Number: M030826
Page 1 of 36 EMC Technologies Pty Ltd ABN 82 057 105 549 57 Assembly Drive Tullamarine Victoria Australia 3043 Ph: + 613 9335 3333 Fax: + 613 9338 9260 email: melb@emctech.com.au EMC Test Report Report
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 3040 Fourth edition 2016-05-01 Geometrical product specifications (GPS) Dimensioning and tolerancing Cones Spécification géométrique des produits (GPS) Cotation et tolérancement
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60044-2 Edition 1.2 2003-02 Edition 1:1997 consolidated with amendments 1:2000 and 2:2002 Instrument transformers Part 2: Inductive voltage transformers IEC 2003 Copyright -
More informationETSI EN V1.2.1 ( )
EN 301 489-19 V1.2.1 (2002-11) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard
More informationThis document is a preview generated by EVS
IEC 61000-4-10 Edition 2.0 2016-07 REDLINE VERSION colour inside BASIC EMC PUBLICATION Electromagnetic compatibility (EMC) Part 4-10: Testing and measurement techniques Damped oscillatory magnetic field
More informationETSI ES V1.2.1 ( )
ES 201 235-4 V1.2.1 (2002-03) Standard Access and Terminals (AT); Specification of Dual-Tone Multi-Frequency (DTMF) Transmitters and Receivers; Part 4: Transmitters and Receivers for use in Terminal Equipment
More informationISO 1519 INTERNATIONAL STANDARD. Paints and varnishes Bend test (cylindrical mandrel) Peintures et vernis Essai de pliage sur mandrin cylindrique
INTERNATIONAL STANDARD ISO 1519 Third edition 2011-01-15 Paints and varnishes Bend test (cylindrical mandrel) Peintures et vernis Essai de pliage sur mandrin cylindrique Reference number ISO 1519:2011(E)
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 16142-1 First edition 2016-03-01 Medical devices Recognized essential principles of safety and performance of medical devices Part 1: General essential principles and additional
More informationAustralian/New Zealand Standard
AS/NZS 61000.6.3:2012 IEC 61000-6-3, Ed.2.1 (2011) AS/NZS 61000.6.3:2012 Australian/New Zealand Standard Electromagnetic compatibility (EMC) Part 6.3: Generic standards Emission standard for residential,
More informationEUROPEAN pr ETS TELECOMMUNICATION February 1996 STANDARD
FINAL DRAFT EUROPEAN pr ETS 300 118 TELECOMMUNICATION February 1996 STANDARD Second Edition Source: ETSI TC-TE Reference: RE/TE-05049 ICS: 33.020 Key words: PSTN, modems Public Switched Telephone Network
More informationFinal draft ETSI EN V1.1.1 ( )
Final draft EN 302 291-2 V1.1.1 (2005-05) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Close
More informationETSI EN V1.1.1 ( ) Harmonized European Standard (Telecommunications series)
EN 302 617-2 V1.1.1 (2010-10) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Ground-based UHF radio transmitters, receivers and
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 7784-2 Second edition 2016-03-15 Paints and varnishes Determination of resistance to abrasion Part 2: Method with abrasive rubber wheels and rotating test specimen Peintures
More informationFinal draft ETSI ES V1.3.1 ( )
Final draft ES 201 235-4 V1.3.1 (2006-01) Standard Access and Terminals (AT); Specification of Dual-Tone Multi-Frequency (DTMF) Transmitters and Receivers; Part 4: Transmitters and Receivers for use in
More informationFinal draft ETSI EN V2.1.1( )
Final draft EN 300 132-3-0 V2.1.1(2011-10) European Standard Environmental Engineering (EE); Power supply interface at the input to telecommunications and datacom (ICT) equipment; Part 3: Operated by rectified
More informationBIODEX MULTI- JOINT SYSTEM
BIODEX MULTI- JOINT SYSTEM CONFORMANCE TO STANDARDS 850-000, 840-000, 852-000 FN: 18-139 5/18 Contact information Manufactured by: Biodex Medical Systems, Inc. 20 Ramsey Road, Shirley, New York, 11967-4704
More informationAustralian/New Zealand Standard
AS/NZS 61000.6.4:2012 IEC 61000-6-4, Ed.2.1 (2011) AS/NZS 61000.6.4:2012 Australian/New Zealand Standard Electromagnetic compatibility (EMC) Part 6.4: Generic standards Emission standard for industrial
More informationINTERNATIONAL STANDARD
IEC 60268-5 INTERNATIONAL STANDARD Edition 3.1 2007-09 Sound system equipment Part 5: Loudspeakers INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 33.160.50 ISBN 2-8318-9286-4 2 60268-5 IEC:2003+A1:2007(E)
More informationTABLE OF CONTENTS FOREWORD... 3 INTRODUCTION SCOPE NORMATIVE REFERENCES... 4
TITLE SPECIFICATION FOR CRIMPED CONNECTING LUGS AND FERRULES PAGE: 1 OF 29 ISION DATE: SEPTEMBER 2014 TABLE OF CONTENTS Page FOREWORD... 3 INTRODUCTION... 4 1 SCOPE... 4 2 NORMATIVE S... 4 3 REQUIREMENTS...
More informationEUROPEAN ETS TELECOMMUNICATION August 1993 STANDARD
EUROPEAN ETS 300 166 TELECOMMUNICATION August 1993 STANDARD Source: ETSI TC-TM Reference: DE/TM-3002 ICS: 33.020, 33.040.40 Key words: Transmission, multiplexing, interfaces Transmission and Multiplexing
More informationDRAFT UGANDA STANDARD
DRAFT UGANDA STANDARD DUS 193-1 First Edition 2018-09-dd Steel wires and wire products for fencing Part 1: Barbed wires Specification Reference number UNBS 2018 Compliance with this standard does not,
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 3310-1 Fifth edition 2016-08-15 Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth Tamis de contrôle Exigences techniques et vérifications
More informationETSI EN V1.1.1 ( )
Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment with an internal or external RF connector
More informationFinal draft ETSI EG V1.1.0 ( )
Final draft EG 203 367 V1.1.0 (2016-03) GUIDE Guide to the application of harmonised standards covering articles 3.1b and 3.2 of the Directive 2014/53/EU (RED) to multi-radio and combined radio and non-radio
More informationAustralian Standard. Switchgear assemblies and ancillary equipment for alternating voltages above 1 kv AS
AS 2067 1984 Australian Standard Switchgear assemblies and ancillary equipment for alternating voltages above 1 kv [Title allocated by Defence Cataloguing Authority: SWITCHGEAR ASSEMBLIES, ELECTRICAL AND
More informationAustralian Standard. Instrument transformers. Part 1: Current transformers (IEC Ed.1.2 (2003) MOD) AS AS
AS 60044.1 2007 AS 60044.1 2007 Australian Standard Instrument transformers Part 1: Current transformers (IEC 60044-1 Ed.1.2 (2003) MOD) This Australian Standard was prepared by Committee EL-013, Measurement
More informationAustralian/New Zealand Standard
AS/NZS CISPR 15:2011 AS/NZS CISPR 15:2011 Australian/New Zealand Standard Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment (CISPR 15,
More informationFinal draft ETSI EN V1.3.1 ( )
Final draft EN 300 433-2 V1.3.1 (2011-05) Harmonized European Standard Electromagnetic compatibility and Radio spectrum Matters (ERM); Citizens' Band (CB) radio equipment; Part 2: Harmonized EN covering
More informationAS/NZS IEC :2013
AS/NZS IEC 61000.4.2:2013 IEC 61000-4-2, Ed.2.0 2008, IDT Australian/New Zealand Standard Electromagnetic compatibility (EMC) Part 4.2: Testing and measurement techniques Electrostatic discharge immunity
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 62055-51 First edition 2007-05 Electricity metering Payment systems Part 51: Standard transfer specification (STS) Physical layer protocol for one-way numeric and magnetic card
More informationETSI EN V1.2.1 ( )
EN 301 489-6 V1.2.1 (2002-08) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard
More informationTECHNICAL TBR 2 BASIS for January 1997 REGULATION
TECHNICAL TBR 2 BASIS for January 1997 REGULATION Source: ETSI TC-TE Reference: DTBR/TE-005002 ICS: 33.020, 33.040.40 Key words: PDN, testing, type approval, X.25 Attachment requirements for Data Terminal
More informationETSI EN V1.3.2 ( ) Harmonized European Standard (Telecommunications series)
EN 302 288-2 V1.3.2 (2009-01) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices; Road Transport and Traffic Telematics
More informationBS EN TESTS ON THE IT TOXIC GAS DETECTOR MODULE
Page 1 of 18 Interference Testing And Consultancy Services (Pty) Ltd ITC SERVICES (PTY) LTD Reg 88/002032/07 Plot 44 Kameeldrift East, Pretoria Private Bag X13 Lynn East 0039 Republic of South Africa Tel
More informationISO INTERNATIONAL STANDARD. Condition monitoring and diagnostics of machines Vibration condition monitoring Part 1: General procedures
INTERNATIONAL STANDARD ISO 13373-1 First edition 2002-02-15 Condition monitoring and diagnostics of machines Vibration condition monitoring Part 1: General procedures Surveillance des conditions et diagnostic
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60728-1 Third edition 2001-11 Cabled distribution systems for television and sound signals Part 1: Methods of measurement and system performance Reference number IEC 60728-1:2001(E)
More informationETSI EN V1.1.1 ( )
EN 301 489-51 V1.1.1 (2016-11) HARMONISED EUROPEAN STANDARD ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 51: Specific conditions for Automotive, Ground based Vehicles
More informationAustralian/New Zealand Standard
AS/NZS 61000.4.11:2005 AS/NZS 61000.4.11:2005 Australian/New Zealand Standard Electromagnetic compatibility (EMC) Part 4.11: Testing and measurement techniques Voltage dips, short interruptions and voltage
More informationThis document is a preview generated by EVS
IEC 61882 Edition 2.0 2016-03 REDLINE VERSION colour inside Hazard and operability studies (HAZOP studies) Application guide IEC 61882:2016-03 RLV(en) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright
More informationAWS J1.1M/J1.1:2013 An American National Standard. Specification for Resistance Welding Controls
An American National Standard Specification for Resistance Welding Controls An American National Standard Approved by American National Standards Institute July 29, 2013 Specification for Resistance Welding
More informationISO 897 INTERNATIONAL STANDARD. Photography Roll films, 126, 110 and 135-size films Identification of the image-bearing side
INTERNATIONAL STANDARD ISO 897 Third edition 2000-10-15 Photography Roll films, 126, 110 and 135-size films Identification of the image-bearing side Photographie Films en bobines et films en formats 126,
More informationISO INTERNATIONAL STANDARD. Space systems Space debris mitigation requirements. Systèmes spatiaux Exigences de mitigation des débris spatiaux
INTERNATIONAL STANDARD ISO 24113 Second edition 2011-05-15 Space systems Space debris mitigation requirements Systèmes spatiaux Exigences de mitigation des débris spatiaux Reference number ISO 24113:2011(E)
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10360-7 First edition 2011-06-01 Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 7: CMMs equipped with
More informationETSI EN V1.1.1 ( )
EN 300 390-2 V1.1.1 (2000-09) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment intended
More informationSummary 18/03/ :27:42. Differences exist between documents. Old Document: en_ v010501p 17 pages (97 KB) 18/03/ :27:35
Summary 18/03/2016 16:27:42 Differences exist between documents. New Document: en_30067602v020101p 16 pages (156 KB) 18/03/2016 16:27:36 Used to display results. Old Document: en_30067602v010501p 17 pages
More informationISO INTERNATIONAL STANDARD. Fluid power systems O-rings Part 1: Inside diameters, cross-sections, tolerances and designation codes
INTERNATIONAL STANDARD ISO 3601-1 Fifth edition 2012-03-01 Fluid power systems O-rings Part 1: Inside diameters, cross-sections, tolerances and designation codes Transmissions hydrauliques et pneumatiques
More information