SOUTH AFRICAN NATIONAL STANDARD
|
|
- Cora Higgins
- 6 years ago
- Views:
Transcription
1 ISBN Edition 3 ISO 898-1:2009 Edition 4 SOUTH AFRICAN NATIONAL STANDARD Fasteners Part 5: General requirements and mechanical properties Section 1: Mechanical properties of fasteners made of carbon steel and alloy steel Bolts, screws and studs This national standard is the identical implementation of ISO 898-1:2009 and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001 Tel: Fax: SABS
2 Edition 3 ISO 898-1:2009 Edition 4 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS TC 2, Screw threads and fasteners, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in January This SANS document supersedes SANS :2003 (edition 2).
3 INTERNATIONAL STANDARD ISO Fourth edition Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread Caractéristiques mécaniques des éléments de fixation en acier au carbone et en acier allié Partie 1: Vis, goujons et tiges filetées de classes de qualité spécifiées Filetages à pas gros et filetages à pas fin Reference number ISO 898-1:2009(E) ISO 2009
4 ISO 898-1:2009(E) Licensed exclusively to SABS. PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel Fax copyright@iso.org Web Published in Switzerland ii ISO 2009 All rights reserved
5 ISO 898-1:2009(E) Contents Page Foreword... iv 1 Scope Normative references Terms and definitions Symbols and abbreviated terms Designation system for property classes Materials Mechanical and physical properties Applicability of test methods General Loadability of fasteners Manufacturer's control Supplier's control Purchaser's control Feasible tests for groups of fasteners and machined test pieces Test methods Tensile test under wedge loading of finished bolts and screws (excluding studs) Tensile test for finished bolts, screws and studs for determination of tensile strength, R m Tensile test for full-size bolts, screws and studs for determination of elongation after fracture, A f, and stress at 0,004 8 d non-proportional elongation, R pf Tensile test for bolts and screws not expected to break in free threaded length due to head design Tensile test for fasteners with waisted shank Proof load test for finished bolts, screws and studs Tensile test for machined test pieces Head soundness test Hardness test Decarburization test Carburization test Retempering test Torsional test Impact test for machined test pieces Surface discontinuity inspection Marking General Manufacturer's identification mark Marking and designation of fasteners with full loadability Marking and designation of fasteners which, because of their geometry, have reduced loadability Marking of packages...53 Annex A (informative) Relation between tensile strength and elongation after fracture...54 Annex B (informative) Influence of elevated temperatures on mechanical properties of fasteners...55 Annex C (informative) Elongation after fracture for full-size fasteners, Α f...56 Bibliography...57 ISO 2009 All rights reserved iii
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-19721-6 ISO 1101:2004 SOUTH AFRICAN NATIONAL STANDARD Engineering drawing Part 2: Geometrical tolerancing Section 1: Tolerancing of form, orientation, location and run-out Generalities,
More informationISO INTERNATIONAL STANDARD. Hexagon socket head cap screws with metric fine pitch thread. Vis à tête cylindrique à six pans creux à pas fin
INTERNATIONAL STANDARD ISO 12474 First edition 2010-10-01 Hexagon socket head cap screws with metric fine pitch thread Vis à tête cylindrique à six pans creux à pas fin Reference number ISO 12474:2010(E)
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 4026 Third edition 2003-12-01 Hexagon socket set screws with flat point Vis sans tête à six pans creux, à bout plat Reference number ISO 4026:2003(E) ISO 2003 ISO 4026:2003(E)
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 4762 Fourth edition 2004-03-01 Hexagon socket head cap screws Vis à tête cylindrique à six pans creux Reference number ISO 4762:2004(E) ISO 2004 PDF disclaimer This PDF file
More informationISO INTERNATIONAL STANDARD. Hexalobular socket pan head screws. Vis à métaux à tête cylindrique bombée large à six lobes internes
INTERNATIONAL STANDARD ISO 14583 Second edition 2011-03-15 Hexalobular socket pan head screws Vis à métaux à tête cylindrique bombée large à six lobes internes Reference number ISO 14583:2011(E) ISO 2011
More informationISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition
INTERNATIONAL STANDARD ISO 16047 First edition 2005-02-01 Fasteners Torque/clamp force testing Éléments de fixation Essais couple/tension Reference number ISO 16047:2005(E) ISO 2005 PDF disclaimer This
More informationISO INTERNATIONAL STANDARD. Hexagon bolts with flange Small series Product grade A
INTERNATIONAL STANDARD ISO 15071 Second edition 2011-06-01 Hexagon bolts with flange Small series Product grade A Vis à tête hexagonale à embase cylindro-tronconique Série étroite Grade A Reference number
More informationISO INTERNATIONAL STANDARD. Hexalobular internal driving feature for bolts and screws. Empreinte à six lobes internes pour vis
INTERNATIONAL STANDARD ISO 10664 Second edition 2005-07-01 Hexalobular internal driving feature for bolts and screws Empreinte à six lobes internes pour vis Reference number ISO 10664:2005(E) ISO 2005
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-29819-7 ISO/IEC 19794-2:2011 SOUTH AFRICAN NATIONAL STANDARD Information technology Biometric data interchange formats Part 2: Finger minutiae data This national standard is the identical
More informationISO INTERNATIONAL STANDARD. Timber structures Dowel-type fasteners Part 1: Determination of yield moment
INTERNATIONAL STANDARD ISO 10984-1 First edition 2009-08-15 Timber structures Dowel-type fasteners Part 1: Determination of yield moment Structures en bois Éléments de fixation de type cheville Partie
More informationISO INTERNATIONAL STANDARD. Welding Studs and ceramic ferrules for arc stud welding
INTERNATIONAL STANDARD ISO 13918 Second edition 2008-02-15 Welding Studs and ceramic ferrules for arc stud welding Soudage Goujons et bagues céramiques pour le soudage à l'arc des goujons Reference number
More informationISO INTERNATIONAL STANDARD. Hexalobular socket cheese head screws. Vis à métaux à tête cylindrique basse à six lobes internes
INTERNATIONAL STANDARD ISO 14580 First edition 2001-09-01 Hexalobular socket cheese head screws Vis à métaux à tête cylindrique basse à six lobes internes Reference number ISO 14580:2001(E) ISO 2001 PDF
More informationISO INTERNATIONAL STANDARD. Fasteners Hot dip galvanized coatings. Éléments de fixation Revêtements de galvanisation à chaud
INTERNATIONAL STANDARD ISO 10684 First edition 2004-07-15 Fasteners Hot dip galvanized coatings Éléments de fixation Revêtements de galvanisation à chaud Reference number ISO 10684:2004(E) ISO 2004 PDF
More informationISO INTERNATIONAL STANDARD. Hexagon bolts with flange with metric fine pitch thread Small series Product grade A
INTERNATIONAL STANDARD ISO 15072 First edition 1999-12-15 Hexagon bolts with flange with metric fine pitch thread Small series Product grade A Vis à tête hexagonale à embase cylindro-tronconique, à filetage
More informationISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 16047 First edition 2005-02-01 Fasteners Torque/clamp force testing Éléments de fixation Essais couple/tension Reference number ISO 16047:2005(E)
More informationISO INTERNATIONAL STANDARD. Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C
INTERNATIONAL STANDARD ISO 4759-1 Second edition 2000-11-15 Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C Tolérances des éléments de fixation Partie 1: Vis, goujons
More informationIrish Standard I.S. EN ISO 898-1:2013
Irish Standard Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
More informationISO INTERNATIONAL STANDARD. Countersinks for countersunk head screws with head configuration in accordance with ISO 7721
INTERNATIONAL STANDARD ISO 15065 First edition 2005-02-15 Countersinks for countersunk head screws with head configuration in accordance with ISO 7721 Fraisures pour vis à tête fraisée avec une configuration
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 7900 Second edition 2006-06-01 Steel wire and wire products for fences Zinc- and zinc-alloy-coated steel barbed wire Fils et produits tréfilés en acier pour clôtures Ronces en
More informationISO 216 INTERNATIONAL STANDARD. Writing paper and certain classes of printed matter Trimmed sizes A and B series, and indication of machine direction
INTERNATIONAL STANDARD ISO 216 Second edition 2007-09-15 Writing paper and certain classes of printed matter Trimmed sizes A and B series, and indication of machine direction Papiers à écrire et certaines
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 139 Second edition 2005-01-15 Textiles Standard atmospheres for conditioning and testing Textiles Atmosphères normales de conditionnement et d'essai Reference number ISO 139:2005(E)
More informationProvläsningsexemplar / Preview INTERNATIONAL STANDARD. Rolling bearings Balls Part 1: Steel balls
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 3290-1 First edition 2008-12-15 Rolling bearings Balls Part 1: Steel balls Roulements Billes Partie 1: Billes de roulement en acier Reference number
More informationISO 3040 INTERNATIONAL STANDARD. Geometrical product specifications (GPS) Dimensioning and tolerancing Cones
INTERNATIONAL STANDARD ISO 3040 Third edition 2009-12-01 Geometrical product specifications (GPS) Dimensioning and tolerancing Cones Spécification géométrique des produits (GPS) Cotation et tolérancement
More informationISO INTERNATIONAL STANDARD. Photography Electronic scanners for photographic images Dynamic range measurements
INTERNATIONAL STANDARD ISO 21550 First edition 2004-10-01 Photography Electronic scanners for photographic images Dynamic range measurements Photographie Scanners électroniques pour images photographiques
More informationISO INTERNATIONAL STANDARD. Rolling bearings Sleeve type linear ball bearings Boundary dimensions and tolerances
INTERNATIONAL STANDARD ISO 10285 Second edition 2007-11-01 Rolling bearings Sleeve type linear ball bearings Boundary dimensions and tolerances Roulements Roulements linéaires à recirculation de billes,
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 20860-1 First edition 2008-10-15 Road vehicles 50 Ω impedance radio frequency connection system interface Part 1: Dimensions and electrical requirements Véhicules routiers Interface
More informationISO INTERNATIONAL STANDARD. Optics and photonics Minimum requirements for stereomicroscopes Part 2: High performance microscopes
INTERNATIONAL STANDARD ISO 11884-2 Second edition 2007-02-01 Optics and photonics Minimum requirements for stereomicroscopes Part 2: High performance microscopes Optique et photonique Exigences minimales
More informationISO INTERNATIONAL STANDARD. Collets with 8 setting angle for tool shanks Collets, nuts and fitting dimensions
INTERNATIONAL STANDARD ISO 15488 Second edition 2003-11-15 Collets with 8 setting angle for tool shanks Collets, nuts and fitting dimensions Pinces de serrage avec angle de réglage de 8 pour queues d'outil
More informationISO INTERNATIONAL STANDARD. Metallic tube connections for fluid power and general use Part 6: 60 cone connectors with or without O-ring
INTERNATIONAL STANDARD ISO 8434-6 First edition 2009-08-15 Corrected version 2010-05-01 Metallic tube connections for fluid power and general use Part 6: 60 cone connectors with or without O-ring Raccordements
More informationISO INTERNATIONAL STANDARD. Mechanical vibration and shock Coupling forces at the man-machine interface for hand-transmitted vibration
INTERNATIONAL STANDARD ISO 15230 First edition 2007-07-01 Mechanical vibration and shock Coupling forces at the man-machine interface for hand-transmitted vibration Vibrations et chocs mécaniques Forces
More informationISO 897 INTERNATIONAL STANDARD. Photography Roll films, 126, 110 and 135-size films Identification of the image-bearing side
INTERNATIONAL STANDARD ISO 897 Third edition 2000-10-15 Photography Roll films, 126, 110 and 135-size films Identification of the image-bearing side Photographie Films en bobines et films en formats 126,
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 29301 First edition 2010-06-01 Microbeam analysis Analytical transmission electron microscopy Methods for calibrating image magnification by using reference materials having
More informationISO INTERNATIONAL STANDARD. Steel wire ropes Vocabulary, designation and classification
INTERNATIONAL STANDARD ISO 17893 First edition 2004-02-15 Steel wire ropes Vocabulary, designation and classification Câbles en acier Vocabulaire, désignation et classification Reference number ISO 2004
More informationISO INTERNATIONAL STANDARD. Paints and varnishes Drying tests Part 1: Determination of through-dry state and through-dry time
INTERNATIONAL STANDARD ISO 9117-1 First edition 2009-05-15 Paints and varnishes Drying tests Part 1: Determination of through-dry state and through-dry time Peintures et vernis Essais de séchage Partie
More informationISO 8752 INTERNATIONAL STANDARD. Spring-type straight pins Slotted, heavy duty
INTERNATIONAL STANDARD ISO 8752 Third edition 2009-06-15 Spring-type straight pins Slotted, heavy duty Goupilles cylindriques creuses, dites goupilles élastiques Série épaisse Reference number ISO 8752:2009(E)
More informationISO INTERNATIONAL STANDARD. Textile machinery Weaving machine temples Part 2: Full-width temples
INTERNATIONAL STANDARD ISO 8118-2 First edition 2006-01-15 Textile machinery Weaving machine temples Part 2: Full-width temples Machines à tisser Templets pour métiers et machines à tisser Partie 2: Templets
More informationISO 5001 INTERNATIONAL STANDARD. Cold-reduced carbon steel sheet for vitreous enamelling
INTERNATIONAL STANDARD ISO 5001 Fourth edition 2007-07-01 Cold-reduced carbon steel sheet for vitreous enamelling Tôles en acier au carbone laminées à froid pour émaillage par vitrification Reference number
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 28721-1 First edition 2008-12-01 Vitreous and porcelain enamels Glass-lined apparatus for process plants Part 1: Quality requirements for apparatus, components, appliances and
More informationISO INTERNATIONAL STANDARD. Natural gas Correlation between water content and water dew point
INTERNATIONAL STANDARD ISO 18453 First edition 2004-07-01 Natural gas Correlation between water content and water dew point Gaz naturel Corrélation entre la teneur en eau et le point de rosée de l'eau
More informationISO INTERNATIONAL STANDARD. Tool holders with cylindrical shank Part 1: Cylindrical shank, location bore Technical delivery conditions
INTERNATIONAL STANDARD ISO 10889-1 Second edition 2004-11-15 Tool holders with cylindrical shank Part 1: Cylindrical shank, location bore Technical delivery conditions Porte-outil à queue cylindrique Partie
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 7380-2 First edition 2011-08-01 Button head screws Part 2: Hexagon socket button head screws with collar Vis à tête cylindrique bombée plate Partie 2: Vis à tête cylindrique
More informationISO 2490 INTERNATIONAL STANDARD. Solid (monobloc) gear hobs with tenon drive or axial keyway, 0,5 to 40 module Nominal dimensions
INTERNATIONAL STANDARD ISO 2490 Third edition 2007-10-01 Solid (monobloc) gear hobs with tenon drive or axial keyway, 0,5 to 40 module Nominal dimensions Fraises-mères monoblocs à entraînement par tenon
More informationISO INTERNATIONAL STANDARD. Paper and board Determination of bending resistance Part 1: Constant rate of deflection
INTERNATIONAL STANDARD ISO 2493-1 First edition 2010-11-15 Paper and board Determination of bending resistance Part 1: Constant rate of deflection Papier et carton Détermination de la résistance à la flexion
More informationISO 216 INTERNATIONAL STANDARD. Writing paper and certain classes of printed matter Trimmed sizes A and B series, and indication of machine direction
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 216 Second edition 2007-09-15 Writing paper and certain classes of printed matter Trimmed sizes A and B series, and indication of machine direction
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 11699-1 Second edition 2008-09-15 Non-destructive testing Industrial radiographic film Part 1: Classification of film systems for industrial radiography Essais non destructifs
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 15547-1 First edition 2005-11-01 Petroleum, petrochemical and natural gas industries Plate-type heat exchangers Part 1: Plate-and-frame heat exchangers Industries du pétrole,
More informationISO INTERNATIONAL STANDARD. Metallic materials Knoop hardness test Part 3: Calibration of reference blocks
INTERNATIONAL STANDARD ISO 4545-3 First edition 2005-11-15 Metallic materials Knoop hardness test Part 3: Calibration of reference blocks Matériaux métalliques Essai de dureté Knoop Partie 3: Étalonnage
More informationISO INTERNATIONAL STANDARD. Internal combustion engines Piston rings Part 1: Rectangular rings made of cast iron
INTERNATIONAL STANDARD ISO 6622-1 Second edition 2003-12-01 Internal combustion engines Piston rings Part 1: Rectangular rings made of cast iron Moteurs à combustion interne Segments de piston Partie 1:
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 11296-4 First edition 2009-11-01 Corrected version 2010-06-01 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 4: Lining
More informationISO INTERNATIONAL STANDARD. Cinematography Spectral response of photographic audio reproducers for analog dye sound tracks on 35 mm film
INTERNATIONAL STANDARD ISO 20859 First edition 2005-06-15 Cinematography Spectral response of photographic audio reproducers for analog dye sound tracks on 35 mm film Cinématographie Réponse spectrale
More informationISO INTERNATIONAL STANDARD. Fasteners Hot dip galvanized coatings. Éléments de fixation Revêtements de galvanisation à chaud
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 10684 First edition 2004-07-15 Fasteners Hot dip galvanized coatings Éléments de fixation Revêtements de galvanisation à chaud Reference number
More informationISO INTERNATIONAL STANDARD
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 20860-1 First edition 2008-10-15 Road vehicles 50 Ω impedance radio frequency connection system interface Part 1: Dimensions and electrical requirements
More informationISO INTERNATIONAL STANDARD. Paints and varnishes Determination of volatile organic compound (VOC) content Part 1: Difference method
INTERNATIONAL STANDARD ISO 11890-1 Second edition 2007-07-01 Paints and varnishes Determination of volatile organic compound (VOC) content Part 1: Difference method Peintures et vernis Détermination de
More informationISO 518 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 518 Second edition 2006-05-15 Photography Camera accessory shoes, with and without electrical contacts, for photoflash lamps and electronic photoflash units Specification Photographie
More informationISO INTERNATIONAL STANDARD. Motorcycle tyres and rims (metric series) Part 3: Range of approved rim contours
INTERNATIONAL STANDARD ISO 5751-3 Sixth edition 2010-11-15 Motorcycle tyres and rims (metric series) Part 3: Range of approved rim contours Pneumatiques et jantes pour motocycles (séries millimétriques)
More informationISO INTERNATIONAL STANDARD. Horology Water-resistant watches. Horlogerie Montres étanches. First edition
INTERNATIONAL STANDARD ISO 22810 First edition 2010-08-01 Horology Water-resistant watches Horlogerie Montres étanches Reference number ISO 22810:2010(E) ISO 2010 PDF disclaimer This PDF file may contain
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10424-2 First edition 2007-11-15 Petroleum and natural gas industries Rotary drilling equipment Part 2: Threading and gauging of rotary shouldered thread connections Industries
More informationISO INTERNATIONAL STANDARD. Optics and photonics Optical coatings Part 3: Environmental durability
INTERNATIONAL STANDARD ISO 9211-3 Second edition 2008-07-01 Optics and photonics Optical coatings Part 3: Environmental durability Optique et photonique Traitements optiques Partie 3: Durabilité environnementale
More informationINTERNATIONAL STANDARD
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 22881 First edition 2004-07-01 Castors and wheels Requirements for use on manually propelled equipment for institutional applications Roues et
More informationISO 463 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 463 First edition 2006-03-01 Geometrical Product Specifications (GPS) Dimensional measuring equipment Design and metrological characteristics of mechanical dial gauges Spécification
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 3442-3 First edition 2007-02-01 Machine tools Dimensions and geometric tests for self-centring chucks with two-piece jaws Part 3: Power-operated chucks with serrated jaws Machines-outils
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 12004-1 First edition 2008-10-15 Metallic materials Sheet and strip Determination of forming-limit curves Part 1: Measurement and application of forminglimit diagrams in the
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 21457 First edition 2010-09-01 Petroleum, petrochemical and natural gas industries Materials selection and corrosion control for oil and gas production systems Industries du
More informationISO INTERNATIONAL STANDARD. Optics and optical instruments Specifications for telescopic sights Part 1: General-purpose instruments
INTERNATIONAL STANDARD ISO 14135-1 First edition 2003-12-01 Optics and optical instruments Specifications for telescopic sights Part 1: General-purpose instruments Optique et instruments d'optique Spécifications
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 13953 First edition 2001-09-15 Polyethylene (PE) pipes and fittings Determination of the tensile strength and failure mode of test pieces from a butt-fused joint Tubes et raccords
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 14703 Second edition 2008-04-15 Fine ceramics (advanced ceramics, advanced technical ceramics) Sample preparation for the determination of particle size distribution of ceramic
More informationISO INTERNATIONAL STANDARD. Technical drawings General principles of presentation Part 44: Sections on mechanical engineering drawings
INTERNATIONAL STANDARD ISO 128-44 First edition 2001-04-15 Technical drawings General principles of presentation Part 44: Sections on mechanical engineering drawings Dessins techniques Principes généraux
More informationISO INTERNATIONAL STANDARD. Ophthalmic instruments Fundus cameras. Instruments ophtalmiques Appareils photographiques du fond de l'œil
INTERNATIONAL STANDARD ISO 10940 Second edition 2009-08-01 Ophthalmic instruments Fundus cameras Instruments ophtalmiques Appareils photographiques du fond de l'œil Reference number ISO 10940:2009(E) ISO
More informationISO INTERNATIONAL STANDARD. Horology Water-resistant watches. Horlogerie Montres étanches. First edition
INTERNATIONAL STANDARD ISO 22810 First edition 2010-08-01 Horology Water-resistant watches Horlogerie Montres étanches Reference number ISO 2010 PDF disclaimer This PDF file may contain embedded typefaces.
More informationISO INTERNATIONAL STANDARD. Small craft Hull construction and scantlings Part 3: Materials: Steel, aluminium alloys, wood, other materials
INTERNATIONAL STANDARD ISO 12215-3 First edition 2002-05-01 Small craft Hull construction and scantlings Part 3: Materials: Steel, aluminium alloys, wood, other materials Petits navires Construction de
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 10511 Third edition 2012-12-15 Prevailing torque type hexagon thin nuts (with non-metallic insert) Écrous hexagonaux bas autofreinés (à anneau non métallique) Reference number
More informationISO INTERNATIONAL STANDARD. Laminate floor coverings Determination of geometrical characteristics
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 24337 First edition 2006-08-01 Laminate floor coverings Determination of geometrical characteristics Revêtements de sol stratifiés Détermination
More informationISO INTERNATIONAL STANDARD. Rolling bearings Sleeve type linear ball bearings Boundary dimensions and tolerances
INTERNATIONAL STANDARD ISO 10285 Second edition 2007-11-01 Rolling bearings Sleeve type linear ball bearings Boundary dimensions and tolerances Roulements Roulements linéaires à recirculation de billes,
More informationISO Prevailing torque type hexagon regular nuts (with non-metallic insert) Property classes 5, 8 and 10
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 7040 Third edition 2012-12-15 Prevailing torque type hexagon regular nuts (with non-metallic insert) Property classes 5, 8 and 10 Écrous hexagonaux
More informationISO INTERNATIONAL STANDARD. Graphic technology Plates for offset printing Dimensions
INTERNATIONAL STANDARD ISO 12635 Second edition 2008-12-01 Graphic technology Plates for offset printing Dimensions Technologie graphique Plaques pour impression offset Dimensions Reference number ISO
More informationISO 1519 INTERNATIONAL STANDARD. Paints and varnishes Bend test (cylindrical mandrel) Peintures et vernis Essai de pliage sur mandrin cylindrique
INTERNATIONAL STANDARD ISO 1519 Third edition 2011-01-15 Paints and varnishes Bend test (cylindrical mandrel) Peintures et vernis Essai de pliage sur mandrin cylindrique Reference number ISO 1519:2011(E)
More informationISO INTERNATIONAL STANDARD. Natural gas Correlation between water content and water dew point
INTERNATIONAL STANDARD ISO 18453 First edition 2004-07-01 Natural gas Correlation between water content and water dew point Gaz naturel Corrélation entre la teneur en eau et le point de rosée de l'eau
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 18055-1 First edition 2004-06-01 Photography and imaging Inkjet media: Classification, nomenclature and dimensions Part 1: Photo-grade media (paper and film) Photographie et
More informationISO INTERNATIONAL STANDARD. Rubber Tolerances for products Part 2: Geometrical tolerances
INTERNATIONAL STANDARD ISO 3302-2 Second edition 2008-10-01 Rubber Tolerances for products Part 2: Geometrical tolerances Caoutchouc Tolérances pour produits Partie 2: Tolérances géométriques Reference
More informationISO INTERNATIONAL STANDARD. Photography Electronic scanners for photographic images Dynamic range measurements
INTERNATIONAL STANDARD ISO 21550 First edition 2004-10-01 Photography Electronic scanners for photographic images Dynamic range measurements Photographie Scanners électroniques pour images photographiques
More informationISO INTERNATIONAL STANDARD. Textiles Determination of spirality after laundering Part 3: Woven and knitted garments
INTERNATIONAL STANDARD ISO 16322-3 First edition 2005-06-01 Textiles Determination of spirality after laundering Part 3: Woven and knitted garments Textiles Détermination du vrillage après lavage Partie
More informationISO/TR TECHNICAL REPORT. Intelligent transport systems System architecture Privacy aspects in ITS standards and systems
TECHNICAL REPORT ISO/TR 12859 First edition 2009-06-01 Intelligent transport systems System architecture Privacy aspects in ITS standards and systems Systèmes intelligents de transport Architecture de
More informationISO INTERNATIONAL STANDARD. Optics and optical instruments Vocabulary for microscopy Part 2: Advanced techniques in light microscopy
INTERNATIONAL STANDARD ISO 10934-2 First edition 2007-03-01 Optics and optical instruments Vocabulary for microscopy Part 2: Advanced techniques in light microscopy Optique et instruments d'optique Vocabulaire
More informationISO/TR TECHNICAL REPORT. Ergonomics Construction and application of tests for speech technology
TECHNICAL REPORT ISO/TR 19358 First edition 2002-10-01 Ergonomics Construction and application of tests for speech technology Ergonomie Élaboration et mise en œuvre des tests des systèmes de technologie
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 1520 Third edition 2006-11-15 Paints and varnishes Cupping test Peintures et vernis Essai d'emboutissage Reference number ISO 1520:2006(E) ISO 2006 PDF disclaimer This PDF file
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 15223-1 First edition 2007-04-15 Medical devices Symbols to be used with medical device labels, labelling and information to be supplied Part 1: General requirements Dispositifs
More informationISO INTERNATIONAL STANDARD. Technical product documentation Lettering Part 6: Cyrillic alphabet
INTERNATIONAL STANDARD ISO 3098-6 First edition 2000-05-01 Technical product documentation Lettering Part 6: Cyrillic alphabet Documentation technique de produits Écriture Partie 6: Alphabet cyrillique
More informationISO Prevailing torque type hexagon nuts (with non-metallic insert), style 2 Property classes 9 and 12
INTERNATIONAL STANDARD ISO 7041 Fourth edition 2012-05-15 Prevailing torque type hexagon nuts (with non-metallic insert), style 2 Property classes 9 and 12 Écrous hexagonaux autofreinés (à anneau non métallique),
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10360-2 Third edition 2009-12-01 Geometrical product specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) Part 2: CMMs used for measuring
More informationISO/TR 2801 Clothing for protection against heat and flame General recommendations for selection, care and use of protective clothing
TECHNICAL REPORT ISO/TR 2801 First edition 2007-02-01 Clothing for protection against heat and flame General recommendations for selection, care and use of protective clothing Vêtements de protection contre
More informationISO 860 INTERNATIONAL STANDARD. Terminology work Harmonization of concepts and terms. Travaux terminologiques Harmonisation des concepts et des termes
INTERNATIONAL STANDARD ISO 860 Third edition 2007-11-15 Terminology work Harmonization of concepts and terms Travaux terminologiques Harmonisation des concepts et des termes Reference number ISO 2007 PDF
More informationISO INTERNATIONAL STANDARD. Earth-moving machinery Lighting, signalling and marking lights, and reflexreflector
INTERNATIONAL STANDARD ISO 12509 Second edition 2004-12-15 Earth-moving machinery Lighting, signalling and marking lights, and reflexreflector devices Engins de terrassement Feux d'éclairage, de signalisation,
More informationISO INTERNATIONAL STANDARD. Technical product documentation Lettering Part 3: Greek alphabet
INTERNATIONAL STANDARD ISO 3098-3 Second edition 2000-05-01 Technical product documentation Lettering Part 3: Greek alphabet Documentation technique de produits Écriture Partie 3: Alphabet grec Reference
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 294-4 Second edition 2001-12-15 Plastics Injection moulding of test specimens of thermoplastic materials Part 4: Determination of moulding shrinkage Plastiques Moulage par injection
More informationISO 5-4 INTERNATIONAL STANDARD. Photography and graphic technology Density measurements Part 4: Geometric conditions for reflection density
INTERNATIONAL STANDARD ISO 5-4 Third edition 2009-12-01 Photography and graphic technology Density measurements Part 4: Geometric conditions for reflection density Photographie et technologie graphique
More informationISO INTERNATIONAL STANDARD. Visual examination of the surface condition of investment castings Steel, nickel alloys and cobalt alloys
INTERNATIONAL STANDARD ISO 19959 First edition 2005-04-01 Visual examination of the surface condition of investment castings Steel, nickel alloys and cobalt alloys Examen visuel de l'état de surface des
More informationISO INTERNATIONAL STANDARD. Textiles Water resistance Rain tests: exposure to a horizontal water spray
INTERNATIONAL STANDARD ISO 22958 First edition 2005-03-15 Textiles Water resistance Rain tests: exposure to a horizontal water spray Textiles Résistance à l'eau Essai d'arrosage: exposition à une pulvérisation
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-34338-5 IEC 60060-3:2006 SOUTH AFRICAN NATIONAL STANDARD High-voltage test techniques Part 3: Definitions and requirements for on-site testing This national standard is the identical implementation
More informationISO/TR TECHNICAL REPORT. Gears Calculation of load capacity of wormgears. Engrenages Calcul de la capacité de charge des engrenages à vis
TECHNICAL REPORT ISO/TR 14521 First edition 2010-11-15 Gears Calculation of load capacity of wormgears Engrenages Calcul de la capacité de charge des engrenages à vis Reference number ISO/TR 14521:2010(E)
More informationISO 2836 INTERNATIONAL STANDARD. Graphic technology Prints and printing inks Assessment of resistance to various agents
INTERNATIONAL STANDARD ISO 2836 Third edition 2004-03-15 Graphic technology Prints and printing inks Assessment of resistance to various agents Technologie graphique Impressions et encres d imprimerie
More information