Module Weight: 45 gm (1.6 oz). 100 count box. Box weight 5 kg (11 lbs). 343mm x 229mm 140mm (13.5 x 9 x 5.5 ).

Size: px

Start display at page:

Download "Module Weight: 45 gm (1.6 oz). 100 count box. Box weight 5 kg (11 lbs). 343mm x 229mm 140mm (13.5 x 9 x 5.5 )."

Kristian O’Neal’
5 years ago
Views:

Specification Features Physical Characteristics Module Source Type: Corrected Cold Phosphor LED Module. Dia. 50mm (1.97 ) x 20mm (0.79 ). Light emitting surface Ø 19mm (0.75 ).

R9 90, R15 95 Color Consistency Maintained: C3/B10/F10 50,000 hrs. (<0.003 u,v 5 years/44,000 hrs. warranty 10 ). Lumen Maintenance: L80/B10/F10 50,000 hrs. (L70, B0, F0 5 years/44,000 hrs.

1 Specification Features Physical Characteristics Module Source Type: Corrected Cold Phosphor LED Module. Dia. 50mm (1.97 ) x 20mm (0.79 ). Light emitting surface Ø 19mm (0.75 ). Maximum Case Temperature: 90 C Phosphor Proximity: Photometric Characteristics Color Consistency Initial: 1 x 2 MacAdam (1 x 2 SDCM) along BBL. Color Rendering Index (CRI): Ra: 98 (typical). R9 90, R15 95 Color Consistency Maintained: C3/B10/F10 50,000 hrs. (<0.003 u,v 5 years/44,000 hrs. warranty 10 ). Lumen Maintenance: L80/B10/F10 50,000 hrs. (L70, B0, F0 5 years/44,000 hrs. warranty 10 ). Other Remote Module Weight: 45 gm (1.6 oz). 100 count box. Box weight 5 kg (11 lbs). 343mm x 229mm 140mm (13.5 x 9 x 5.5 ). Interfaces- Electrical Interface- Mechanical Interface- Thermal Module Housing: Storage Temperature: -40 C to 85 C Electrical: 6-Pin terminal. Tyco part # P. Mating connector Tyco Pin-out: P1 + power, P2 - power, P3 open, P4 open, P5 control+, P6 control-. 600mm harness accessory available through Avnet (part # ). Xicato sample part # XSA-331. Mechanical: Recommended mounting screws: M3 x 0.5mm x 25mm with split lock washer. Torque 0.4Nm (3.5 in-lb) using three-hole pattern. Thermal: Integral thermal pad. A mating thermal interface (i.e. heatsink) surface flatness of 0.1 mm and center hole less than Ø12 mm is recommended in order to maintain thermal performance. Injection molded 30% glass-filled PBT. Regulatory: Mercury Content UV or IRC Emissions: UL recognized Class 2, CE (IEC62031, Class III), RoHS 2 compliant. IP20. Photobiological Safety (EN62471:2008), ESD Class 3B (HBM). DALI compliance-tested (IEC /102:2009 and IEC ). None None Module Lifetime 100, C 10 PRODUCT DATA SHEET: XIM LED Module DALI, Artist Series Dec pg. 1

Color Information Color Consistency Initial Color

Gamut Color Rendering Index (3000K Typical) Ra R1 R2 R3

98 98 99 98 98 98 97 98 98 98 99 98 88 98 98 98 PRODUCT

2 Color Information Color Consistency Initial Color Consistency Maintained Spectral Power Distribution Color Gamut Color Rendering Index (3000K Typical) Ra R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 Artist Series PRODUCT DATA SHEET: XIM LED Module DALI, Artist Series Dec pg. 2

3 Dimming Information Dimming Protocol: DALI IEC /102:2009 and IEC ). Dimming Profile: Logarithmic or Linear (configurable via DALI. Default is logarithmic). Dimming Compatibility: XIM is compatible with a wide range of DALI dimming systems from leading industry manufacturers. Potentiameter NA Compatibility Logarithmic Curve Linear Curve PRODUCT DATA SHEET: XIM LED Module DALI, Artist Series Dec pg. 3

4 Over Temperature Protection LED luminaires are designed to operate within a specific ambient temperature range. Occasionally the ambient temperature will exceed the design temperature. For example, if insulation is unintentionally placed on or near the luminaire. Additionally, the thermal management system (e.g. heat sink) may get installed incorrectly, which could increase the LED module s temperature above the recommended limit. In these cases, the performance of the electrical components (LEDs and driver electronics) are placed at risk. To address this risk, XIM features over-temperature protection. XIM contains a temperature sensor, that monitors the Tc of the LEDs. If the temperature exceeds 93 C, XIM s integrated electronics reduce the intensity which then lowers both current and the temperature. The intensity is reduced to 85% of the commanded intensity over a period of 60 seconds. If the temperature drops below 93 C, but stays above 85 C, XIM will maintain the intensity at the reduced level. If the temperature drops below 85 C, XIM will increase intensity back to 100% of the commanded intensity over a period of 60 seconds. The Thermal Overload diagram below illustrates this behavior. PRODUCT DATA SHEET: XIM LED Module DALI, Artist Series Dec pg. 4

5 If the module temperature stays below 98 C, but stays above 93 C for 5 minutes, XIM will immediately limit the maximum intensity to 10%. The intensity limit will stay at 10% even if the temperature drops below 85 C. To remove the limit, the user must set the commanded intensity to 0% (turn off the light) and the temperature must be below 93 C. Then, when the user sets the commanded intensity to above 0% (turns on the light), XIM will set the light to the commanded intensity (no reduction). A power cycle of XIM will also remove the limit. The Thermal Overload Lockout diagram below illustrates this behavior. If at any time, the module temperature exceeds 98 C, XIM will immediately turn off the LEDs. The LEDs will stay off even if the temperature drops below 85 C. To turn on the LEDs again, the user must set the commanded intensity to 0% (turn off the light) and the temperature must be below 93 C. Then, when the user sets the commanded intensity to above 0% (turns on the light), XIM will set the light to the commanded intensity (no reduction). A power cycle of XIM will also allow the LEDs to be turned on. The Thermal Shut Down diagram below illustrates this behavior. PRODUCT DATA SHEET: XIM LED Module DALI, Artist Series Dec pg. 5

6 Technical Data Module 1300 lm Part Number XIM A2A XIM A2A XIM A2A XIM A2A 2700K 3000K 3500K Lighting 1 Electrical 5 Correlated Color Color Rendering Temperature (CCT) 2 Index (Ra) K CRI Ra 98 R9 90 R15 95 Initial Color Consistency SDCM CCT Duv ± 40K Lumen Maintenance (hrs) 4 Control Protocol Constant Voltage (V) 6 Required Input Parameters Module Power Consumption (W) Lumen Output (Typical) 8 Efficacy (Typical) Minimum Current (ma) 7 Typ. Max lm lm/w ± 50K 1 x 2 ± 60K ± k DALI 48 ± 5% ± 70K 1. All lighting data shown in the above table is taken at a recommended operating test point (Tc) temperature of 70 C and highest rated drive current. 2. "3000K" and "3500K" CCT's are 2950K and 3420K, respectively. CCT data ANSI/NEMA compliant. 3. Ra is defined as the average of color rendering indices R1-R K data shown. Value is typical. 4. L80 50,000 hrs. Long term testing in process. 5. The module is designed for usage with a constant voltage power supply. 6. Absolute minimum voltage into the module is 41V. Absolute maximum voltage into the module is 56V. These specifications include PSU output tolerance, ripple, noise, wire length voltage drop, line regulation, load regulation, over/undershoot, turn on delay, or any other source of variation. Voltage data based on 20 C to 90 C operating range. For operation outside this range, contact Xicato. 7. While the PSU is energized, the PSU must be able to supply up to 5mA, even when the light is commanded off via a lighting control system. Minimum input current to the XIM is the minimum current that the PSU must be able to supply in all conditions to ensure full light output. 8. Absolute range of lumen output is ±10% of typical value. 9. Specifications subject to change without notice year color and lumen maintenance warranty. Refer to for details. PRODUCT DATA SHEET: XIM LED Module DALI, Artist Series Dec pg. 6

7 Recommended LED Module in Luminaire Specification Physical Characteristics: LED module shall be Corrected Cold remote phosphor, nominal 50mm (1.97 ) diameter, and 20mm (0.79 ) in height. Performance: LED module shall have a CRI (Ra) 98 with an R9 85. LED module color points shall be within 1 x 2 SDCM initial. Flux output shall be measured at a minimum of 70 ºC (±5ºC). Dimming Performance: Module shall dim to 0.1% (measured flux) at lowest level. Fading across the dimming range shall be smooth and monotonic. When power is applied, the module shall set the light to the POWER-ON level according to the timing in the DALI specification (IEC ). Minimum flicker frequency at 1% measured light output shall be 1.25 khz. General Requirements: LED module shall be UL recognized, CE compliant and RoHS compliant. Module shall be warranted for 5 years for catastrophic failure, lumen maintenance ( L70), and color consistency (<.003 u, v ). LED module shall be Xicato Module. # About Xicato Xicato is passionate about light. Light has an emotional effect on people and a direct impact on business profitability. It ultimately influences everything in our lives. Xicato is a recognized leader in creating LED modules that provide superior aesthetics, economics and durability. Xicato aspires to be the trusted partner of the global lighting design community and luminaire manufacturers. For an overview of our customers luminaires visit PRODUCT DATA SHEET: XIM LED Module DALI, Artist Series Dec pg. 7

Module Weight: 45 gm (1.6 oz). 100 count box. Box weight 5 kg (11 lbs). 343mm x 229mm 140mm (13.5 x 9 x 5.5 ).

Module Weight: 45 gm (1.6 oz). 100 count box. Box weight 5 kg (11 lbs). 343mm x 229mm 140mm (13.5 x 9 x 5.5 ). Specification Features Physical Characteristics Module Source Type: Corrected Cold Phosphor LED Module. Dia. 50mm (1.97 ) x 20mm (0.79 ). Light emitting surface Ø 19mm (0.75 ). Maximum Case Temperature: