INVITATION FOR QUOTATION. TEQIP-III/2018/mecj/Shopping/19

Transcription

1 INVITATION FOR QUOTATION TEQIP-III/2018/mecj/Shopping/19 23-Jul-2018 Dear Sir, 1. You are invited to submit your most competitive quotation for the following goods with item wise detailed specifications given at Annexure I, Sr. No Brief Description Quantity Delivery Period(In days) Place of Delivery Installation Requirement (if any) 1 3 Phase Induction Motor Speed Control Trainer 2 AC Motor Speed Control Trainer 3 AC Position Control System 4 Advance PLC based hardware & software system 5 Advance Solar Energy Training system 2 15 Department of

2 6 Ammeter (portable) 1 7 Ammeter (portable) 2 8 Ammeter (portable) 3 9 Ammeter (portable) 4 10 Artificial Wind Turbine 11 Brushless DC Motor Trainer 12 DC Motor Speed Control Trainer 13 DC Position Control System Department of 5 15 Department of Department of 5 15 Department of 2 15 Department of

3 14 Digital Control System 2 15 Department of 15 Digital Multimeter Department of 16 Energy Measurement system 17 LVDT Measurement Trainer System 18 MOSFET Based Fly Back Coverter 19 PC Based Data Acquisition System 20 PLC based Wirelessly controlled sensor Lab 21 Pressure Measurement Trainer

4 22 SCR Based Rectifier 125A 23 Solar Power Inverter 500VA 24 Strain Gauge Trainer System 25 Study of Second Order Networks 26 Study of Stepper Motor 27 Transformer Single Phase 28 Voltmeter (portable) 1 29 Voltmeter (portable) Department of 2 15 Department of 2 15 Department of Department of Department of

5 2. Government of India has received a credit from the International Development Association (IDA) towards the cost of the Technical Education Quality Improvement Programme[TEQIP]-Phase III Project and intends to apply part of the proceeds of this credit to eligible payments under the contract for which this invitation for quotations is issued. 3. Quotation, 3.1 The contract shall be for the full quantity as described above. 3.2 Corrections, if any, shall be made by crossing out, initialing, dating and re writing. 3.3 All duties and other levies payable by the supplier under the contract shall be included in the unit price. 3.4 Applicable taxes shall be quoted separately for all items. 3.5 The prices quoted by the bidder shall be fixed for the duration of the contract and shall not be subject to adjustment on any account. 3.6 The Prices should be quoted in Indian Rupees only. 4. Each bidder shall submit only one quotation. 5. Quotation shall remain valid for a period not less than 20 days after the last date of quotation submission. 6. Evaluation of Quotations, The Purchaser will evaluate and compare the quotations determined to be substantially responsive i.e. which 6.1 are properly signed ; and 6.2 confirm to the terms and conditions, and specifications. 7. The Quotations would be evaluated for all items together. 8. Award of contract: The Purchaser will award the contract to the bidder whose quotation has been determined to be substantially responsive and who has offered the lowest evaluated quotation price. 8.1 Notwithstanding the above, the Purchaser reserves the right to accept or reject any quotations and to cancel the bidding process and reject all quotations at any time prior to the award of contract.

6 8.2 The bidder whose bid is accepted will be notified of the award of contract by the Purchaser prior to expiration of the quotation validity period. The terms of the accepted offer shall be incorporated in the purchase order. 9. Payment shall be made in Indian Rupees as follows: Delivery and Installation - 10% of total cost Satisfactory Acceptance - 90% of total cost 10. All supplied items are under warranty of months from the date of successful acceptance of items. 11. You are requested to provide your offer latest by 11:00 hours on 20-Aug Detailed specifications of the items are at Annexure I. 13. Training Clause (if any) 14. Testing/Installation Clause (if any) 15. Information brochures/ Product catalogue, if any must be accompanied with the quotation clearly indicating the model quoted for. 16. Sealed quotation to be submitted/ delivered at the address mentioned below, College, Faculty of Engineering & Architecture, Jai Narain Vyas University, Residency Road, Ratanada, Jodhpur 17. We look forward to receiving your quotation and thank you for your interest in this project. Annexure I (Authorized Signatory) Name & Designation Sr. No Item Name Specifications

7 1 3 Phase Induction Motor Speed Control Trainer 2 AC Motor Speed Control Trainer A] Powder coated sturdy Aluminum flat panel (table top) system, carrying various high voltage components housed in plastic enclosures (panel) to minimize shock possibility. 1f Motor, nator & Sync. Motor Panel q 1f MCBs of 4A/1.6A 2nos, bulb load. Instrumentation Power supply cum Multichannel DPM panel (a) +/-12 V,500 ma (b) +5V,300mA (c) Unregulated 17V dc/750 ma (d) line synchronizing signal. (e) 13V / 3 Amp. (f) Multi channel DPM for digital display of torque, speed etc. SCR Actuator (variable DC) cum sensor signal conditioning panel q Half bridge SCR based 0V-195V / 5 Amp cosine firing with linear charateristics. q Supports signal conditioning circuit for speed, torque in kg wt to output 0-2.5Vdc (FS). Integrated AC (1 phase) measurement panel q 1 nos. of Digital meter for 1f.parameters V, I, PF, W, VA, VAR, Hz, etc. q Current specs = 1A/5A for 1f meter ( V). AC voltmeter panel ) q Voltage range: 300V. q 1 pole 4 way switch to line voltage for three phase Dual range AC ammeter panel q Current range:2a/6a able. q 1 pole 7 way switch to phase current for three phase IGBT Controlled AC Drive panel 1) Input voltage: 230VAC. 50Hz 2) Output voltage: 3 phase 230 VAC 3) Range (Frequency Control): 0.1 Hz to 100 (400)Hz 4) Control Mode :Sine Wave PWM 5) Capacity : 1/2 HP 6) With Reverse and Forward Direction 7) Mech.: single width for ½ HP 8) Motor: 3 phase squirrel cage induction motor, ½ HP, 4 pole, 1500RPM, 6 terminal (delta 220Vac/star 440Vac) motor with digital speed measurement assembly AC volt meter and AC ammeter panel n AC voltmeter n AC Ammeter Instrumentation Power supply cum Multi channel DPM panel n +/- 12 V, 500 ma n +5V, 300 ma n Line synchronizing signal n Multichannel DPM for digital display speed SCR Actuator (variable AC0 cum sensor signal conditioning panel n Full bridges SCR based 0V-230 VAC/12Amp n Support signal conditioning circuit for speed to give output 0-2.5V DV (Fs) n Electronic tacho: 0-1V/1000rpm Motor Specification Table top machine / Accessories: Fractional HP AC/DC motor 230VAC, 1/12 HP. Chasis mounted table top with brake pulley and spring balance (5 Kg) loading arrangement

8 3 AC Position Control System 4 Advance PLC based hardware & software system 5 Advance Solar Energy Training system 2 phase servomotor 12V/ phase, 50Hz, 10W Power amplifier for driving Servo potentiometer type error detector In built 10.00V (rms) panel meter Step response capture/display card Detailed literature with typical results included Complete unit except a measuring CRO Hardware 1, Moduler Type of system Controllers & I/O modules with Modbus TCP, Bacnet, KNX, DALI and Variours Other configuration. 2, On board serial port capable of communicating over EIA232 or EIA485 network (switchable) 3, On board 2X 10/100 MBPS Managed Ethernet ports within built bob smith termination. 4, On board SD card slot capable of supporting upto 32 GB. 5, Miminum 256 MB Flash RAM and 256 MB Main Memory. 6, EMC immunity of interference as per EN , EMC emission of interference as per EN , Standard 35mm DIN Rail Mounted IO cards. 9, All Status and Diagnostic LEDs. 10, Supports Analog signals with minimum bit resolution. 11, Operating temperature range of 0 C to 60 C and 95% RH. Software/Programming 1, complete programming and configuration for PLC, on Linux Operating system 2, Supports IT protocols for communication including FTP, FTPS, HTTP, HTTPS, SNMP, DHCP, NTP, FNS, SSH. 3, Supports industrial communication protocol MODBus (TCP, UDP and RTU). 4, Supports all IEC programming languages (Ladder, Functional Block Diagram, Instruction List, Structured Text, Continuous Function Code) 6, Able to log data for a miminum of 30 days on onboard SD card. 7, Able to log data on PC based SQL, CSV for trend and report generation. 8, Programmable be other languages like Linux, C++, Visual Basic, Java, Matlabetc 9, Configurable via onboard Ethernet as well as USB ports. The company must provide a 1 year hardware warranty,and service for the system supplied. The advance solar energy training system must have various components for complete learning and study the complex issue for solar. System must be supplied with 2 high performance photovoltaic cell panel 200W (100W Each) for a 12Vdc voltage. 50X50mm 2 set of solar panel for study of effective of light with respect to different wave length for spectral response and carrier life time Solar source in the form of halogen lamps 500 watt with

9 moveable stand. MPPT standalone inverter with proper battery connections etc Charge controller 12v DC I LUX meter: To measure the Intensity of light source on panel using. Inverter 12V to 220V AC, 12v dc loads (FAN, LED LIGHT) to study load test, cfl for AC load. Battery: Capacity12V: 7AH Facility for digital volt and ammeter for onboard voltage and current measurement Facility for series parallel connection working of solar panel Peltier module to capture and study temperature effect of solar radiation PID controlled SCR based sensor signal conditioning panel PT 100 sensor for temp monitoring, facility for PC Based Data Acquisitions for the Plotting of Graph such as voltage versus time etc. The System is having Capability to Store all Solar Radiation in Memory Card. Set of interconnection cables. Testing point for fault analysis for each section. Voltage at maximum power point (Vmpp): 24.0 V. Current at maximum power point (Impp): 1 A. panel movement with different aspect of angle. Anodized aluminum framework for modules allocation. Option for study of angle and direction of solar panel and light source. Solar Energy data loggers supports the following measurements: AC Current, AC Voltage, Amps (A), Kilowatt Hours (kwh), Power Factor (PF), Volt-Amps (VA), Volts (V), Watt Hours (Wh) and Watts (W). Type of Inputs: 1 Phase, 2 phases, 3 phase (3Ø-3/4 wire, 2Ø-3 wire, 1Ø- 2 wires) Feature: Password protection CT Primary: 1A/5A CT Secondary: 1 or 5 A Sampling Rate: Readings taken automatically every 600 sample/sec to 1sample/week. Storage Capacity: 1 Million Samples. Display: 16*2 LCD Display Communication: GSM/USB/MODBUS The unit must provide Solar Power / Irradiance Measurement with Orientation & Tilt Angle) Facility to measure Solar Power in the range from 400 to 1100 nanometers. The good Spectral Instantaneous display Ave/Min/Max values 20 points memory Socket of tripod mounting Magnetic mount Backlit LCD and 4 digits triple display 6 Ammeter (portable) 1 7 Ammeter (portable) 2 AC type, Current range 0-1 Amps AC Current range 0-1 type, Current range 0-30 Amps

10 8 Ammeter (portable) 3 9 Ammeter (portable) 4 10 Artificial Wind Turbine 11 Brushless DC Motor Trainer DC type, Amps DC type, Current range 0-10 Amps Artificial Wind Generating Unit WIND GENERATOR Body material Aluminum Rotor Diameter 124.5cm (49inches) Starting Wind speed 3.5m/s Survival Wind Speed 13m/s Voltage 45m/s Rated Power 24V AC/DC Maximum Power 450W Weight 550W Yaw Body/Tower Mount Inner Diameter 53.3MM, 2.1 INCH Recommended Tower (Pipe) size 1.5 inch schedule 40 pipe Actual pipe Diameter: 40mm (1.9 inch) recommend adding 2.5mm padding CHARGE CONTROLLER Voltage 24V Power Rate 600W INVERTER Input Voltage 24V Power rating 200W EXIDE BATTERY Capacity 80Ah Voltage 24V Control Unit Different meters Ammeters Dual LED Digital Ammeter Amp volt meter + current shunt DC 100V 50 A Voltmeters Dual LED Digital Voltmeter Amp volt meter + current shunt DC 100V 50 A Wattmeter Energy meters Protection devices Accessories Power analyzer Input Voltage V AC Input Current 2A/ 5A/ 10A Measurement True RMS Accuracy Class 0.2 and for P.F. ± Display Four Rows 7- Segment Display Experiment manual Connecting leads Anemometers Measure wind speed (air velocity) & Temperature simultaneously Choice of reading in meters /second, km/hour, feet/min, MPH or knots Measuring range 0 to 5860 feet/min Max/Average/Current reading function? C/?F temperature unit ion Large LCD with backlight Manual/ Auto power off Wind Chill indication With Beaufort scale Low battery Powder coated sturdy Aluminum flat panel (table top) system, carrying various voltage components housed in plastic enclosures (panel). Instrumentation Power supply cum Multichannel DPM panel (EMT 8) +5V, 300mA Multi channel DPM for digital display for speed BLDC-1 panel 24VDC/3A power supply for BLDC motor BLDC-2 panel, BLDC controller circuit. BLDC motor Forward/reverse switch. Brake switch Test points for PWM outputs, Tacho output. Speed control Pot. Brush less DC motor Voltage: 24VDC Wattage:200W Max Speed: 2500RPM. Frame: 34, panel mounted

11 Bidirectional Braking system 12 DC Motor Speed Control Trainer 13 DC Position Control System 14 Digital Control System Instrumentation Power supply cum Multi- channel DPM panel [10 Shrouded Banana] (a) +/-12 V, 500 ma (b) +5V, 300mA (c) Unregulated 17V dc/750 ma (d) line synchronizing signal. (e) Multi channel DPM for digital display of speed, etc. 2] SCR Actuator (variable DC) cum sensor signal conditioning panel x 2 Nos. [4 Shrouded Banana] 1. Full bridge SCR based 0V-195V / 12 Amp cosine firing with linear charateristics. 2. Supports signal conditioning circuit for speed to give output 0-2.5Vdc (FS). 3. supplies required for DC Armature & DC motor field. 3] DC voltmeter and DC ammeter panel [14 Shrouded Banana] a) DC voltmeter (0-300V) b) DC Ammeter (0-5A) with polarity protection diode c) Field failure relay to control Armature supply. Both 6A/6B needed simultaneously DC Integrated Motor Specifications: 180V/300W/1500RPM with series shunt and compound windings, Chasis mounted table top with spring balance loading arrangement [10kg] and Electronic Tacho:1V/1000RPM. Optional: Electrical Tacho: 10V/1000RPM. Weight : 25 Kg. Position control of a 12V, 1A d.c. gear motor (50rpm) Provision for positive and negative tachogenerator feedback Tacho constant: 2V/1000 rpm approximately Calibrated dials for reference and output position: resolution 1º up based waveform capture card Literature and patch cords included Built-in 3½ digit DVM for signal measurements Built-in step signal and IC regulated power supplies for electronic circuits Servo-potentiometers with full 360º rotation Separate unit for motor in a see through cabinet Essential accessory a CRO Second order simulated process (analog process) Built in D/A and A/D circuits (8 bit) 8085 based up-kit as digital controller with user software in 8K EPROM 16 bit arithmetic for algorithmic calculations Square wave test input (internal) 16 built in levels of P, I and D gains each. Complete flexibility for the user to develop own software IC regulated internal built in power supplies Detailed literature and patch cords included

12 Essential accessory a CRO 15 Digital Multimeter DC voltage range 0-200mv - 2v - 20v - 200v v (with resolution 10 micro to 100mv) accuracy.02% AC voltage range 0-200mv - 2v - 20v - 200v - 750v (with resolution 10 micro to 100mv) accuracy.02% DC/AC Current range 0-200microamp mA, 20 amp (with resolution 10 neno to 1mA) accuracy.01% Resistance range 0-200? - 2k? - 20k? - 200k? - 2M?, 20M? (with resolution 10M? to 1k?) accuracy.1% Capacitance 0 to 20nf/2µf/200µf Frequency 0 to 20KHz/200KHz 16 Energy Measurement system Facility to program the Ethernet Programmable field bus Controller store the acquired in the relational database. The system must be provided with Power Measurement Module andmodbus RTU to measure electrical data in the three-phase supply network As well as energy meters. Based on the measured current and voltage values, other electrical values are calculated. Ethernet LAN Cable: for communication between the system and the PC. Facility for dual source energy measurement, for genset based generations. Facility for Current Transformers: to step-down the three-phase current supply to be safely applied to the ower measurement module. The system must be enclosed in metal enclosure for safety, and must have all items like Power supply unit for controller and modules in side. Facility to store the data in AQL format and excel format. 1, 2, 4, 8 or 16 Channels per module. Fieldbus independent node design. Fieldbus Coupler for different protocols and requirements. Fieldbus Coupler with PLC functionality (controllers) for distributed control networks in compliance with IEC Digital / Analog inputs / outputs and special functions with different voltage and signal types can be assembled in one Fieldbus coupler (node) Standalone PLC with facility for connecting system to other big PLCs/ DCS. Automatic detection of master failure in networked environment will make your system safer. Battery less and huge memory for any complicated task. (50 % less space as compared to other system. PLC - ETHERNET Programmable Fieldbus Controller; Multitasking; MODBUS 3- Phase Power Measurement Module 480V Modbus RTU

13 interface system 4-Channel Digital Input Module 24 V DC 4-Channel Digital Output Module 24 V DC 4-Channel Analog Input Module 4-20 ma 4-Channel Analog Output Module 4-20 ma End Module Power Supply, 1-Phase(DC 24 V; 2.5 A) USB communication cable; Length 2.5 m Software Development Dual Source energy measurement Modules Microcontroller based energy measurement system, With LCD display, for various electrical parameters like Automatic switching of display based on input source (EB/DG). Load hours and ON hours for both sources. Positive energy accumulation/ reverse lock programmable. Programmable to kwh or kvah. OLD registers to store the previously cleared energy values. 17 LVDT Measurement Trainer System 18 MOSFET Based Fly Back Coverter System with AC-AC spring loaded 20mm LVDT PIC microcontroller based system LCD 16*2 display unit to show LVDT output results 4.2KHZ Frequency generator with test points to adjust frequency Test points for test LVDT calibration using multimeter On board power reset switch with LED indicator Buzzer indicator for finding LVDT null point Operational amplifier and signal conditioning circuit with test points System come with operating user Manual, connecting cables & power supply PIC18F452 WITH ALL SUPPRT CIRCUITERY ON BOARD Reprogramming Facility using USB. Facility to Log the Data into PC using USB PC interface. 6 Analog and 12 Digital Channels to Interface the Data into Pc. One number of powers MOSFET IRF840 used as power switch with Suitable heat sink TL 494 IC based PWM generator One number of high speed Opto isolator provided for PWM isolation Driver IC IR2110 used to drive power switch High frequency transformer provided for isolation USB interface can connect to computer, Large LCD analog bar graph display Data logging of online parameters wrt time. Power circuit I/P voltage +15V DC Output voltage 0-5 VDC/1 amp 230V AC input +15 DC for control circuit One number of fuse provided for protection Voltage feedback from the output for closed loop operation. 19 PC Based Data 20 Digital I/O (Up to 50 Hz per I/O) Having 8 channel 12- Bit Analog Inputs, 2 Analog Outputs, On board 8 digital

14 Acquisition System output (LED's) & on board 8 digital input(dip) On board Relay, Buzzer Section. Temp Sensors (LM35, Pt100) Proximity switches, LDR (LM 324 & LDR) & IR Sensors On Board signal conditioning For above sensor USB Bus with data acquisition system Complete Software Control & it supports Labview software codes for the above mentioned sensors. switch)on board buzzer for indication Facility for external signal interface, with Potentiometer. It supports Software or Hardware Timed Acquisition Re-programmable facility & PC interface with Lab view Easy to perform. 20 PLC based Wirelessly controlled sensor Lab 21 Pressure Measurement Trainer 22 SCR Based Rectifier 125A 8-Channel Digital Input/ Output Module 24 V DC 4- Channel Analog Input/ Output Module 4-20 ma Wago Bluetooth transceiver module Wifi module for wireless control and programming Wago thermocouple and RTD module End Module Licensed version (GUI) Software and Processor should must be from Wago (German). Accessories 6 Relays and Contactor Connection made with Screw less technology Industrial sensor like, RTD, thermocouple, proximity and PIR, smoke sensor(one each) One Stepper motor 24v DC and driver with step angle controlled 8 Input switches 8 Output led s 2mm connectors Trainer kit must be supplied with different blocks in metallic frame. On Board Pressure Sensor with 2PSI fs Output is Ratio metric to the Power Supply Facility to generate and monitor Pressure In Both Engineering Units mmhg as well as Psi Units Based On 8051 microcontroller LED indicators, On Board LCD Display Each section is having testing point. On board signal conditioner. Output data on PC using USB Based Data Acquisition system and with reprogrammable facility GUI Data can be Plot in MATLAB and LABVIEW DC Variable Rectifier, (Input: 3Ph, 415V AC, 50Hz, Output: 230V DC) Rectifier SCR Based Soml controlled type Input 3phase 415V AC 50Hz Output 0-230V DC Variable with potentiometer Enclosed in MS Fabricated, Powder coated Self standing control panel Protections for negative phase sequence Over current, short circuit, under voltage, over voltage Provided with a/m, v/m, lamps, ON/OFF push

15 buttons & Potentiometer, Air natural cooling, 4sets of parallel output, Rating continuous 23 Solar Power Inverter 500VA 1. Training system control panel should have rating of 500 VA and it should be used as solar training system and also power generation as well. 2. Training system control panel should have built in DC voltmeters, DC ammeters, AC multifunction meter (for AC current, voltage, power, frequency) 3. Training should have control panel built in protection circuit for battery & solar panel 4. System output of meter must be record for analysis with 8 GB SD card using data logging facility, Type of Inputs: 1 Phase Feature: Password protection CT Primary: 1A/5A In Build RTC for Date and Time stamp. CT Secondary: 1 or 5 A Sampling Rate: Readings taken automatically every 600 sample/sec to 1sample/week. Storage Capacity:1 Million Samples.Display: 20*4 LCD Display/ Communication: GSM/USB/MODBUS 5. Training system control panel have built in BS-10 terminals for making the connection 6. Training System includes 250Wp solar panel: 2 Nos., Battery 100Ah: 2 Nos., Charge Controller: 1 No., Inverter: 600 VA Control panel for experiments equipped with meters, connecting terminals and switches 7. Solar Panel: 02 nos Pm: 250Wp 8. Control Panel with Inverter Inverter Capacity 600VA 9. Battery: 02 nos Solar Battery of Capacity: 12V/100Ah, 10. Charge Controller: Solar PV Module: 24 50V, Current: 40A, Battery voltage: 24V, Technology: PWM based MPPT, Charging Stage: Bulk, Absorptions and Float 11. Energy meter: AC Current, AC Voltage, Amps (A), Kilowatt Hours (kwh), Power Factor (PF), Volt-Amps (VA), Volts (V), Watt Hours (Wh) and Watts (W). 12. Training platform should be used for conduct below experiment A. Measurement and Analysis of Different parameters of Solar PV Module : open circuit and short circuit, parameter measurement with series and parallel PV Modules, I-V characteristic and Power curve of PV module and PV array., efficiency and fill factor B. Load Estimation and calculation C. Study of Charge controller D. Study of different parameter of inverter efficiency, PWM switching, charging of batteries, over load and over battery protection Main cord, Patch cord, Operating manual

16 24 Strain Gauge Trainer System 25 Study of Second Order Networks 26 Study of Stepper Motor 27 Transformer Single Phase 28 Voltmeter (portable) 1 29 Voltmeter (portable) 2 PIC 18F452 µcr based trainer system Strain Gauge (350O): 2 Nos. Gauge Factor: 2.11, ±1% Maximum Weight Capacities: 1.5kg Cantilever Material: Stainless Steel Bridge Voltage: +5 V DC External Cantilever Arrangement High Repeatability and Reliability Bridge Configuration: Half Bridge Test-Points to Observe Input Output of Each Block. Onboard Offset Null Adjustment. Built In DC Power Supplies +5V,-5V DC. Display: 3½ Digits LED/16X2 LCD Display Power Supply: 230 V 50 Hz Power Cord, User's Manual and connecting cables to be included Standard Weights and Patch Cord Study of strain, stress measurement using strain gauges using cantilever method. Study of linear range of operation of strain measurement. Pressure measurement using strain gauge sensor method. Output data on PC using USB Based Data Acquisition system and with reprogrammable facility Using GUI Data can be Plot in MATLAB and LABVIEW Active RLC network using 3-Op Amps Damping (approx) Square Wave Hz, 0-1V (typical) Sine Wave Hz, 0-IV (typical) Essential accessory: a CRO Single stepping and free running modes of operation with speed variation and direction reversal internal TTL circuit 360º motion servo-potentiometer position pickup for motor dynamics Operation through microprocessor kit sample control programs provided Stepper motor specification: Torque : 2.8 Kg-cm Step angle : 1.8º Power : 12V, 1A/phase Essential accessory a CRO 2KVA, 50Hz, 230V Single Phase Primary Tapping Com/50%/86.6%/100% Secondary Tapping Com/50%/86.6%/100% AC type, Voltmeter ranges volts DC type, Voltmeter range volts

17

18 FORMAT FOR QUOTATION SUBMISSION (In letterhead of the supplier with seal) Date: To: Sl. Description of Qty. Unit Quoted Unit rate in Rs. Total Price Sales tax and other No. goods (with full (Including Ex Factory price, excise duty, packing and (A) taxes payable Specifications) forwarding, transportation, insurance, other local In In figures costs incidental to delivery and warranty/ guaranty % (B) commitments) Total Cost Gross Total Cost (A+B): Rs. We agree to supply the above goods in accordance with the technical specifications for a total contract price of Rs. (Amount in figures) (Rupees amount in words) within the period specified in the Invitation for Quotations.

19 We confirm that the normal commercial warranty/ guarantee of months shall apply to the offered items and we also confirm to agree with terms and conditions as mentioned in the Invitation Letter. We hereby certify that we have taken steps to ensure that no person acting for us or on our behalf will engage in bribery. Signature of Supplier Name: Address: Contact No: