General Specifications

Size: px

Start display at page:

Download "General Specifications"

Damian Griffin
5 years ago
Views:

1 General I/O Adaptors (for N-IO) GENERAL This General (GS) covers the hardware specifications of I/O adaptors that allow for setting extended functions of the Analog Digital I/O Module (A2MMM843), such as I/O signal conversion and isolation between inputs and outputs for each channel. The adaptors are mounted to the Base Plate for Adaptor (A2BN3D) and used. STANDARD SPECIFICATIONS Type of I/O adaptor A2SAP105 A2SDV105 A2SDV505 A2SDV506 A2SMX801 Name Extended function Pulse Input Signal Adaptor (0 to 10 khz) Digital Input Adaptor (24 V DC Voltage Input, Dry Contact Input ) Digital Output Adaptor (24 V DC, Current Source: 0.5A) Relay Output Adaptor (24 V DC, Dry Contact Output: 0.5A) Pass-through I/O Signal Adaptor (Pass-through I/O Signal) Contact ON/OFF, voltage pulse, current pulse, and isolated channels Voltage input, Dry contact input, and isolation (*1) 24 V DC/0.5 A output, current source, and isolation (*1) 24 V DC/0.5 A relay contact (dry contact NO/NC), and isolated channels Used to use the basic functions of A2MMM843, and Non-isolated (*2) Note: For signal connection to the Base Plate for Adaptor (A2BN3D) using an I/O adaptor, refer to the TI CENTUM VP Installation Guidance (TI 33J01J10-01EN). *1: Isolated from I/O module. Non-isolated from each channel. *2: Non-isolated from I/O module. [Release 6] Yokogawa Electric Corporation , Nakacho, Musashino-shi, Tokyo, Japan Tel.: Fax.: Copyright Feb (YK) 5th Edition Nov. 1, 2016 (YK)

2 2 Pulse Input Signal Adaptor (for 0 to 10 khz) A2SAP105 Input signal 2-wire type: Contact ON/OFF, voltage pulse, current pulse (possible to supply transmitter power supply) 3-wire type: Power-supply-type voltage pulse Input frequency 0 to 10 khz (*1) Minimum input pulse width Input signal level 40 μs or more Contact input Relay contact, transistor contact Open/close detection level Open: 100 kω or more Close: 200 Ω or less Contact capacity: 15 V DC/15 ma or more (when supplying 12 V DC) 30 V DC/30 ma or more (when supplying 24 V DC) Voltage/current pulse input (Current input is converted to voltage) VH (high level): 3 to 24 V DC VL (low level): -1 to 8 V DC VH - VL (Swing width): 3V or more Signal source resistance 1 kω or less Shunt resistance Can be Selected from ON (4k Ω) or OFF (*2) Filter Filter for eliminating chattering can be set (*3) Pull-up resistance 68 kω (12 V DC or 24 V DC) Transmitter power supply Can be selected from 24 V DC or 12 V DC 12 V DC ± 1.2 V DC/35 ma or less 24 V DC ± 2.4 V DC/24 ma or less (Output current limitation: 40 ma DC or less) (*4) 24 V DC system power supply: 50 ma 5 V DC internal power supply: 10 ma (*5) Withstanding voltage Between input signal and system: 1500 V AC for 1 minute, 42 V DC (*6) Between I/O adaptors: 500 V AC for 1 minute, 42 V DC Data update period For A2SAP105 alone: 2 ms (*7) *1: Connection for the following frequencies in the case of receiving dry contact signal. 0 to 5 khz : Connect the input signal between A and B terminals. 0 to 10 khz : Connect the input signal between A and B terminals and connect an external shunt resistor of 1 kω between C and D terminals. 0 to 800 Hz : Connect the input signal between B and C terminals. *2: In the case of OFF, select a shunt resistance value from the following table and provide an external resistor of the resistance value. Resistance 220 Ω ±5% 1 W 510 Ω ±5% 1 W 1 kω ±5% 2 W Rated power Provide a terminal block for the external resistor to be mounted on. The following table shows recommended terminal blocks. For details on mounting, refer to the TI CENTUM VP Installation Guidance (TI 33J01J10-01EN). Manufacturer Phoenix Contact WAGO PT 2, 5-TG , D-PT 2, 5-MT , P-CO (Up to 1 W resistor can be mounted) (x2), , (UP to 3 W resistor can be mounted) Use A2SAP105-S1 (with explosion protection) only in an application where an external resistor is not required because the A2SAP105-S1 cannot take an external resistor due to the regulation of the standards for hazardous location equipment. *3: When the pulse input signal is a dry contact (e. g. mechanical relay) up to 10 Hz, chattering can be eliminated. *4: If A2SAP105 is powered off or overcurrent is detected, the transmitter power supply terminal is opened. *5: Internal power supply means the power supply that draws power from the Analog Digital I/O Module (A2MMM843). *6: For the withstanding voltage when connecting a field power supply, refer to the GS Base Plates (for N-IO) (GS *7: Delay is up to 10 ms including the data update period of 8 ms of the Analog Digital I/O Module (A2MMM843). Nov. 1,

3 3 Digital Input Adaptor (24 V DC Voltage Input, Dry Contact Input) Input format Rated input voltage Input current (at rated input voltage) Input ON voltage Input OFF voltage A2SDV105 Voltage input and dry contact input 24 V DC (voltage input) 6 ma ±1.2 ma 18 to 26.4 V DC (voltage input) 5.0 V DC or less (voltage input) Field voltage rating 24 V DC ±2.4 V DC (contact input), current capacity: 10 ma or more (*1) Input ON resistance Input OFF resistance Maximum allowable input voltage Withstanding voltage Input response time 1 kω or less (contact input) 50 kω or more (contact input) 30.0 V DC Between input signal and system: 1500 V AC for 1 minute, 42 V DC (*2) Between I/O adaptors: 500 V AC for 1 minute, 42 V DC (*3) (*4) 24 V DC system power supply: Unused 5 V DC internal power supply: 14 ma (*5) For A2DV105 alone: 150 μs In combination with the Analog Digital I/O Module (A2MMM843): Up to 22 ms *1: Current capacity of one A2SDV105 unit in normal operation. Current capacity is 20 ma when the circuit is grounded. *2: For the withstanding voltage when connecting a field power supply, refer to the GS Base Plates (for N-IO) (GS *3: Not isolated between A2SDV105 and A2SDV505 (common is shared). *4: The following shows the allowable potential difference in common mode. Between dry contact inputs: Non isolated Between voltage inputs: 30 V for 1 minute Between voltage input and dry contact input: 30 V for 1 minute *5: Internal power supply means the power supply that draws power from the Analog Digital I/O Module (A2MMM843). Digital Output Adaptor (24 V DC, Current Source: 0.5 A) Output format A2SDV505 Current source Field power supply rating 24 V DC ±2.4 V DC, current capacity: 0.55 A or more (*1) Voltage drop 1 V or less (*2) Leak current maximum value when output off 1 ma or less Maximum load current 500 ma (including rush current) (*3) Load resistance range Withstanding voltage Output response time 48 Ω or more 24 V DC system power supply: Unused 5 V DC internal power supply: 18 ma (*4) Between output signal and system: 1500 V AC for 1 minute, 42 V DC (*5) Between I/O adaptors: 500 V AC for 1 minute, 42 V DC (*6) For A2SDV505 alone: 5 ms In combination with the Analog Digital I/O Module (A2MMM843): Up to 17 ms *1: Current capacity of one A2SDV505 unit in normal operation. Current capacity is 0.8 A when the circuit is shorted. *2: Voltage drop includes that from the field power supply input terminal to the field connection terminal via the module. *3: If an inductive load is driven, be sure to connect a spark killer diode. *4: Internal power supply means the power supply that draws power from the Analog Digital I/O Module (A2MMM843). *5: For the withstanding voltage when connecting a field power supply, refer to the GS Base Plates (for N-IO) (GS *6: Not isolated between A2SDV105 and A2SDV505 (common is shared). Feb. 1,

4 4 Relay Output Adaptor (24 V DC, Dry Contact Output: 0.5A) Rated applied voltage Maximum load Maximum voltage Maximum current Output format Withstanding voltage Relay switching life Relay operating time Relay recovery time A2SDV V DC Resistance load: 24 V DC/0.5 A, 30 V DC/0.5 A Inductive load: 24 V DC/0.5 A, 30 V DC/0.4 A (*1) Resistance load: 30 V DC, inductive load: 30 V DC Resistance load: 0.5 A DC (including rush current), Inductive load: 0.5 A DC (including rush current) NC/NO Between output signal and system: 1500 V AC for 1 minute, 42 V DC (*2) Between I/O adaptors: 500 V AC for 1 minute, 42 V DC Resistance load: 100,000 open/close cycles (at maximum load) Inductive load: 100,000 open/close cycles (at maximum load) For A2SDV506 alone: 8 ms or less (bouncing is not included) In combination with the Analog Digital I/O Module (A2MMM843): Up to 20 ms For A2SDV506 alone: 20 ms or less (bouncing is not included) In combination with the Analog Digital I/O Module (A2MMM843): Up to 32 ms 24 V DC system power supply: Unused 5 V DC internal power supply: 8 ma (*3) Note: Replacement is not recommended when current flows through the terminals, because the connectors of the base plate and this module may be damaged or deteriorate. Turn off the field signal externally before replacing this module. Note: Operating temperature range is -40 to 70 C. However, if mounted on the same base plate with A2SAP105, the operating temperature range is -40 to 60 C. *1: If an inductive load is driven at the output contact, be sure to connect a spark killer diode. *2: For the withstanding voltage when connecting a field power supply, refer to the GS Base Plates (for N-IO) (GS *3: Internal power supply means the power supply that draws power from the Analog Digital I/O Module (A2MMM843). Pass-through I/O Signal Adaptor (Pass-through I/O Signal) I/O signal Current consumption A2SMX801 Signals from a field device are output as is to the Analog Digital I/O Module (A2MMM843). Conversely, signals from the Analog Digital I/O Module (A2MMM843) are output as is to the field device. No current is consumed Feb. 1,

5 5 EXTERNAL DIMENSIONS 130 Unit:mm Nominal Tolerances : When the reference dimension is over 0.5 mm and equal or less than 120 mm, its nominal tolerance is ± 0.8 mm, while its combination of nominal tolerance is ± 1.5 mm. When the reference dimension is over 120 mm, its nominal tolerance is in accordance with JEM MODELS AND SUFFIX CODES Pulse Input Signal Adaptor A2SAP105 Pulse Input Signal Adaptor (0 to 10 khz) Digital Input Adaptor A2SDV105 Digital Input Adaptor (24 V DC Voltage Input, Dry Contact Input) F01.ai Dec. 28,

6 6 Digital Output Adaptor A2SDV505 Digital Output Adaptor (24 V DC, Current Source: 0.5 A) Relay Output Adaptor A2SDV506 Relay Output Adaptor (24 V DC, Dry Contact Output: 0.5 A) Pass-through I/O Signal Adaptor A2SMX801 Pass-through I/O Signal Adaptor (Pass-through I/O Signal) APPLICABLE STANDARDS Refer to the GS Integrated Production Control System CENTUM VP System Overview (GS 33J01A10-01EN). ORDERING INFORMATION Specify models and suffix codes when ordering. For selecting the right products for explosion protection, please refer to TI 33Q01J30-01E without fail. TRADEMARKS CENTUM is a registered trademark of Yokogawa Electric Corporation. Other company and product names appearing in this document are trademarks or registered trademarks of their respective holders. Subject to change without notice. Dec. 28,

General Specifications

General Specifications General I/O Adaptors (for N-IO) GS 33J62F30-01EN [Release 6] GENERAL This General (GS) describes the hardware specifications of I/O adaptors that enable extended functions setting for analog digital I/O