Level Switch Type NRS Original Installation Instructions English

Transcription

1 Level Switch Type NRS 0 N nglish Original Installation Instructions

2 Contents Important Notes age Usage for the intended purpose...5 Safety note...5 Danger...5 Attention...5 LV (Low Voltage) Directive and MC (lectromagnetic Compatibility)...5 ATX (Atmosphère xplosible)...5 xplanatory Notes Scope of supply...6 Description...6 Function...6 System components...6 Design...6 Technical Data NRS Corrosion resistance...8 Name plate / marking...8 Dimensions...8 Design NRS Key... Functional lements NRS Key... Installation NRS 0... Tools... xample of installation... Key...

3 Contents continued lectrical Connection age Control cable... Note... CAN bus voltage supply... Attention... Wiring diagram Key...8 CAN bus wiring diagram...8 Attention...9 Note...9 Tools...9 Basic Settings CAN bus...0 Node ID... Factory setting... Assigning / changing node ID... Attention... Code switch settings... Commissioning Using the operating & display unit URB... NRS Measuring range... stablishing measuring range... 5 Switchpoints and proportional band...6 stablishing switchpoints Operation NRS

4 Contents continued age NRS Alarm NRS High-level () alarm... Low-level () alarm... Malfunctions Fault-finding list for troubleshooting... System Malfunctions Danger... NRS Danger... Systematic malfunction analysis... System malfunction...5 System malfunction...5 System malfunction...6 System malfunction...7 Decommissioning Danger...8 Disposal...8 Annex Note regarding Declaration of Conformity / Declaration of Manufacturer...8

5 Important Notes Usage for the intended purpose Use level switch NRS -0 in conjunction with level electrode NRG 6-0 only for monitoring and regulating the level of conductive liquids. Safety note The equipment must only be installed and commissioned by qualified and adequately trained personnel. Maintenance and retrofitting must only be performed by entrusted personnel who through adequate training have achieved a recognised level of competence. Danger The terminal strip of the NRS -0 is live during operation. This presents the danger of electric shock! Cut off power supply before mounting or removing the terminal strips and the housing cover. Attention The name plate specifies the technical features of the equipment. Note that any piece of equipment without its specific name plate must neither be commissioned nor operated. LV (Low Voltage) Directive and MC (lectromagnetic Compatibility) The equipment meets the requirements of the Low Voltage Directive 0/5/U and the MC Directive 0/0/U. ATX (Atmosphère xplosible) According to the uropean Directive ATX 0//U the equipment must not be used in potentially explosive atmospheres. 5

6 xplanatory Notes Scope of supply NRS -0 Level switch type NRS -0 (plug-in unit in plastic case with box terminals) Terminating resistor 0 Ω Installation & Operating manual Description Use level switch type NRS -0 in combination with level electrode type NRG 6-0 for level monitoring. The level switch has the following functions: n Four liquid levels with one switchpoint each. n High-level alarm, low-level alarm, pump ON, pump OFF, with one switchpoint each. n Continuous level monitoring within control band defined by two preset limits. n Actual-value output -0 ma n Contact multiplication by connecting in parallel a second level switch NRS -0 without actual value output. The level data are transmitted via CAN-bus from the electrode NRG 6-0 to the level controller or further system components. Function At regular intervals the level electrode type NRG 6-0 sends a data telegram to the level switch NRS -0. The data transfer is effected by means of a CAN bus according to DIN ISO 898. The transferred measuring data are then evaluated and assigned to the manually adjusted switchpoints. To guarantee the correct functioning and safety of the system the data transmitting cycle is constantly monitored by the level switch. When the CAN bus line is interrupted the level switch sends a visual signal to indicate a malfunction and the relays and will be instantaneously de-energized (alarm position). Additional functions, e.g. (de)-energizing delay times of the output relays ( to 5 sec.) can be adjusted with the control terminal and display unit URB / URB. System components NRG 6-0 Level electrode NRG 6-0, N 0 Design NRS -0 nclosure made from insulating material with box terminals for installation in control cabinets. The terminals are externally accessible. Mounting on a standardised supporting rail TS 5 x 5 DIN N 500. xternal dimensions: 7 x 00 x 8 6

7 Technical data NRS 0 Type approval no. NRS -0: TÜV. XX-99 Input / Output Interface for CAN bus to DIN ISO 898 using CANopen Output voltage supply for electrodes ower supply V DC, short-circuit protected Analogue output 0 ma, load 500 Ω for display of actual value. volt-free relay contacts. Max. contact rating with switching voltages of V AC, 5 V AC and 0 V AC: A resistive, 0.75 A inductive at cos ϕ 0.5 Max. contact rating with a switching voltage of V DC: A. Contact material: silver, hard-gold plated Interference suppression rovide contactor with an external RC combination (00 Ω / 7nF) Relay de-energizing delay Output, s Indicators and adjustors red LD for switchpoint High level () red LD for switchpoint Low level () green LDs for switchpoints UM ON and UM OFF green LD ower red LD Bus fault ten-pole code switch for node ID and baud rate settings pushbuttons Supply voltage 0 V ± 0 %, 50/60 Hz 5 V ± 0 %, 50/60 Hz (option) ower consumption 0 VA rotection Case: I 0 to DIN ISO 6059 Terminal strip: I 0 to DIN ISO 6059 Admissible ambient temperature 0 C to 55 C nclosure material Front panel: polycarbonate, grey Case: polycarbonate, black Weight Approx. 0.8 kg 7

8 Technical data continued Corrosion resistance If the equipment is used for its intended purpose, its safety is not impaired by corrosion. Name plate / marking Betriebsanleitung beachten See installation instructions Voir instructions de montage Steuergerät control device appareille de commande 0V -5/+0% 5VA NRS -0 Node ID: I 0 (I0) IN / OUT: CAN-Bus 8-6 V DC Tamb = 55 C ( F) - C L S C H S S V DC CAN-BUS + - L N X ext -0 ma NRG 6-0 NRS -0 NRS -0.. Fig. Münchener Str. 77 D-85 Bremen TÜV. WR. -99 Seriennummer Dimensions NRS -0 8 Fig

9 Design NRS 0 a ON NRS Fig. 9

10 Functional lements NRS 0 NRS-0 Fig NRS -0 Fig. 5 ON

11 Design / Functional lements / Installation Key Indicator LDs Discharge control Fill control Malfunction LD switchpoint High-level alarm High-level alarm Multifunction LD switchpoint ump ON ump OFF Multifunction LD switchpoint ump OFF ump ON Multifunction LD switchpoint Low-level alarm Low-level alarm Multifunction LD Bus status LD ower nter button / test mode 5 Decrease button 6 Increase button 7 rogram button 8 Code switch, 0 poles 9 Terminal strip 0 Screws for terminal strip a nclosure b Supporting rail TS 5 x 5 to DIN N 500 Installation NRS 0 Installation on mounting rail. Clip control unit onto mounting rail 5 x 5 mm (DIN N 500).. Align control unit, Fig. 7 Tools n Screwdriver (5.5/00)

12 Installation continued xample of installation a NRS -0 b Fig NRS Fig

13 lectrical Connection Control cable NRS, NRR, LRR, TRS, URB Note that screened multi-core twisted-pair control cable is required for the BUS line, e.g. UNITRONIC BUS CAN x x... mm or R-YCYV-fl x x... mm. Control cable assemblies ( x x 0. mm with connector and coupler) of various lengths are available as optional extra. NRG, LRG, F, URZ, TRV, URB The equipment is fitted with a sensor-connector union (5 poles, A-coded). For the connection of the BUS devices control cable assemblies (with connector and coupler) of various lengths are available as optional extra. Note that the recommended control cables are not UV resistant and, if installed outdoors (apart from URB ), must be protected by a UV resistant plastic jacket or a cable duct. The baud rate (data transfer rate) dictates the cable length and conductor size of the cable between the bus nodes. The total power consumption must also be taken into account when selecting the con ductor size. The total power consumption is calculated from the number of bus nodes. If the cable length between the steam boiler and the control cabinet exceeds 5 m, we recommend that you fit a branching box that is resistant to electromagnetic interference (stock code no. 50) and to use a control cable with a larger conductor size for the distance to the control cabinet. S 8 S 9 S 0 Baud rate Cable length Number of pairs and conductor size [mm ] OFF ON OFF 50 kbit/s 5 m Factory setting x x 0. ON ON OFF 5 kbit/s 50 m x x 0.5 OFF OFF ON 00 kbit/s 5 m x x 0.75 ON OFF ON 50 kbit/s 500 m OFF ON ON 0 kbit/s 000 m on request, dependent on bus configuration ON ON ON 0 kbit/s 000 m The baud rate is set via the code switch 9. Make sure that all bus nodes have the same settings. UNITRONIC is a registered trademark of LA Kabelwerke GmbH, Stuttgart

14 lectrical Connection continued Note n The max. baud rates and cable lengths indicated above are based on empirical values obtained by. In certain cases it may be necessary to reduce the baud rate in order to ensure trouble-free operation. n The design of the data cable has a strong influence on the eletromagnetic immunity (MC). Take special care when connecting the equipment. n If you do not use the control cable assemblies connect the connectors and jacks for the control cables as indicated in the assignment diagram for sensor connector unions. CAN bus voltage supply To ensure troublefree operation the CAN bus system must be supplied with sufficient voltage. lease use the following table to check the voltage supply of your bus system. Control units with voltage supply Measuring transducers, transmitters, control units, operating & display unit URB Qty. x ower rating per equipment = Sum x 6 W = W lease enter data! Sum = W Qty. x ower rating per equipment = Sum x W = W Operating & display unit URB x 5 W = W lease enter data! Sum = W If sum exceeds sum, the CAN bus voltage must be supplied by a separate, stabilised safety power supply unit (e.g. SITO smart V,.5 A) with V DC. The power supply unit must be electrically isolated from dangerous contact voltages, meeting at least the requirements on double or reinforced isolation acc. to DIN N 5078 or DIN 600- or DIN N or DIN N (safe isolation). The power supply unit must be provided with an overcurrent protective device in accordance with N Attention If a safety power supply unit (e.g. SITO smart, V,.5 A) is used for the voltage supply of the CAN bus do not tap the supply voltage from the terminals and 5 of the control devices. SITO smart is a registered trademark of Siemens AG, München

15 lectrical Connection continued Wiring diagram d L N e f g NRS S Fig. 8 l l V DC + C L C H CAN-Bus k 0 Ω h 5

16 lectrical Connection continued Wiring diagram continued K ump contactor L K N NRS S l l V DC + C L C H CAN-Bus Fig. 9 Discharge control ump OFF at low level () k 0 Ω h 6

17 lectrical Connection continued Wiring diagram continued L K ump contactor K N NRS l l S V DC + C L C H CAN-Bus Fig. 0 Fill control ump OFF at high level () k 0 Ω h 7

18 lectrical Connection continued Key d Mains voltage e limit contact ( alarm) f ump control Fill control: Discharge control: = ump OFF = ump ON = ump ON = ump OFF g limit contact ( alarm) h Actual value output -0 ma k Terminating resistor 0 Ω, RS or RS l Twisted pair control cable for CAN bus line m Valve actuator n Feedback potentiometer 000 Ω actuator CAN bus wiring diagram URB NRS, NRR, LRR, C*) TRS, URB NRG, LRG, F, URZ TRV *) Central earthing point Fig. RS RS 8

19 lectrical Connection continued Attention n Wire equipment in series. Star-type wiring is not permitted. n Interlink screens of control cables such that electrical continuity is ensured and connect them once to the central earthing point (C). If equipotential currents may occur, e.g. in outdoor installations, separate the screen from the central earthing point (C). n To protect the switching contacts fuse circuit with.5 A (slow blow) or according to TRD regulations (.0 A for 7 hrs operation). n If more than one system component is connected to a CAN bus network provide the first and last equipment with a terminating resistor of 0 Ω. Fig., Fig. n The CAN bus line must not be interrupted while operating with one or more system components. In the event of an interruption the safety circuit will be opened! If the switching controller has to be replaced first remove the terminal strips 9, Fig. Note: Make sure that all system components connected are not operating before removing the CAN bus line from the terminal strip. Note n Connect screen only to terminal, ensuring electrical continuity and connect equip ment once to the central earthing point (C). n The loop resistance must be under 0 Ω. n The rated voltage is stated on the name plate. n When switching off inductive loads, voltage spikes are produced that may impair the operation of control and measuring systems. Connected contactors must therefore be provided with RC combinations, e. g. 0. µf / 00 Ω. n Despite correct wiring system failure and malfunction messages may occur because of high frequency malfunctions caused by the system. For more information refer to the section Troubleshooting. Tools n Screwdriver for slotted screws, size.5, completely insulated according to VD

20 Basic Settings CAN bus All level and conductivity controllers and associated electrodes are interconnected by means of a CAN bus adopting the CANopen protocol. very item of equipment features an electronic address (Node ID). The four-core bus cable serves as power supply and data highway for high-speed data exchange. The CAN address (Node ID) can be set between and. The equipment is configured at our works and ready for service with other system components without having to set the node ID. If several systems of the same kind are to communicate in one CAN bus network, be sure to assign one node ID for each individual system component (e. g. controller and probe) acc. to the table on page. If the length of the CAN bus cable exceeds 5 m, use code switch 8 (Fig. 8) to change the switch positions. Note: The baud rate must be identical for all items of euqipment! For more information refer to the section Basic Settings Code switch settings. 0

21 Basic Settings continued Node ID Low-level limiter NRS -0 NRG 6-0 () NRG 6-0 () Reserved Reserved X X + X + X + X + Factory setting Safety system for steam boilers with superheater NRS -0. NRG 6-0 () NRG 6-0 () TRV 5-0 Limiter X X + X + X + X + Factory setting Safety system (e.g. pressurised hot-water generating unit) NRS -0. NRG 6-0 () NRG 6-0 () Limiter Limiter X X + X + X + X + Factory setting Safety system (e.g. pressurised hot-water generating unit) NRS -0. TRV 5-0 () TRV 5-0 () Limiter Limiter X X + X + X + X Factory setting TRS 5-0 () TRS 5-0 () X X High-level alarm NRS - NRG 6- Reserved Reserved Reserved X X + X + X + X Factory setting Further components SRL 0 X = Sensor (low-level limiter / high-level alarm) + Factory setting ORT 6 98 Factory setting On-off level control Reserved NRS - NRG 6- X X X Factory setting Modulating level control URZ 0 NRS -0 NRR -0 NRG 6-0 Reserved X X X X + X Factory setting Automatic continuous blowdown control F -0 LRR -0 LRG -... Reserved X X X + X Factory setting Operating unit URB, URB 60 Factory setting

22 Basic Settings continued Factory setting The level switch features the following factory set default values: n Baud rate: 50 kb/s n Control equipment: n Node ID: 09 n Control equipment: n Node ID: 00 n Switchpoint : 80 % n Switchpoint : 60% n Switchpoint : 0% n Switchpoint : 0% n Relay with energizing delay switchpoint : s n Relay with energizing delay switchpoint : s n Relay with energizing delay switchpoint : s n Relay with energizing delay switchpoint : s n Relay with de-energizing delay switchpoint : s n Relay with de-energizing delay switchpoint : s n Relay with de-energizing delay switchpoint : s n Relay with de-energizing delay switchpoint : s Fig. 5 /80 % /60 % /0 % /0 % 00 % 0%

23 Basic Settings continued Assigning / changing node ID If several systems of the same kind are to communicate in one CAN bus network, be sure to assign one node ID for each individual system component (e. g. controller, limiter). In most cases it is sufficient to commission the equipment with the default factory setting. Detach the lower terminal strip 9 (Fig. 6) in order to change the code switch 8 settings. Attention n We recommend that you commission the CAN bus equipment with their default factory settings. n Make sure that no node ID is used twice in the CAN bus network! Code switch settings Node ID 9 S ON S ON S ON S OFF 8 S5 OFF 6 S6 ON S7 OFF ON ON Node ID 7 S OFF S ON S OFF S ON 8 S5 OFF 6 S6 OFF S7 ON 6 Fig. 6 (Factory setting) Fig. 7 (xample) S8 S9 S0 Baud rate Cable length OFF ON OFF 50 kbit/s 5 m ON ON OFF 5 kbit/s 50 m OFF ON ON 00 kbit/s 5 m ON ON ON 50 kbit/s 500 m OFF ON ON 0 kbit/s 000 m ON ON ON 0 kbit/s 000 m Fig. 8 (Factory setting: 50 kbits/s)

24 Commissioning Using the operating & display unit URB... If you use the operating unit URB... make all adjustments via its user interface. NRS -0 Apply power to the unit. The four indicator LDs flash rapidly. The LD ower lights up. The system test cycle takes about sec. NRS -0 Measuring range A Desired measuring range [mm] B Max. measuring range C Lowest measuring point stablish the measuring range A for your level monitoring application. 7 NRG 6-0 Fig. 0 B 6 A C stablishing measuring range ress button for sec. Lower the liquid level in the vessel until the lower limit of the measuring range A is reached. Use button if you want to establish the upper limit of the desired control range first. If two control devices are used only one has to be adjusted. NRS -0

25 Commissioning continued stablishing measuring range continued ress button briefly. Note: In the event of a system malfunction, the LD(s) Bus status and/or ower will be flashing rapidly when in program mode. Quit program mode and analyse the system malfunction (see pages 6 ). NRS -0 ress button briefly. The lower limit of the measuring range is now saved. NRS -0 ress button briefly. Raise liquid level until the upper limit of the desired measuring range A is reached. NRS -0 ress button briefly. Wait for 0 seconds before continuing the procedure. To compensate for short-term fluctuations of the liquid level a filter is integrated in the preamplifier of the electrode. If you confirm the setting too early not the exact 00 % value will be saved. NRS -0 ress button twice briefly. The upper limit of the desired measuring range is now saved. The NRS -0 is back in operating mode. NRS -0 5

26 Commissioning continued Switchpoints and proportional band NRG 6-0 A Fig. You can establish four switchpoints within the selected measuring range. 6

27 Commissioning continued stablishing switchpoints ress button briefly. Raise or lower the liquid level in the vessel until the desired value is reached. Use button if you want to establish a different switchpoint first. NRS -0 ress button briefly. Lower or raise liquid level until switchpoint within the adjusted control range is reached. Note: In the event of a system malfunction the LD(s) Bus status and/or ower will be flashing rapidly. NRS -0 ress button briefly. Switchpoint is now saved. NRS -0 ress button briefly. Switchpoint is now active. NRS -0 ress button briefly. Raise liquid level until switchpoint within the adjusted control range is reached. NRS -0 7

28 Commissioning continued stablishing switchpoints continued ress button briefly. Switchpoint is now saved. NRS -0 ress button briefly. Switchpoint is now active. NRS -0 ress button briefly. Raise liquid level until switchpoint within the adjusted measuring range is reached. NRS -0 ress button briefly. Switchpoint is saved. NRS -0 ress button briefly. Switchpoint is now active. NRS -0 8

29 Commissioning continued stablishing switchpoints continued ress button briefly. Raise liquid level until switchpoint within the adjusted measuring range is reached. NRS -0 ress button twice briefly. Switchpoint is saved. The NRS -0 is again in operating mode. NRS -0 9

30 Operation NRS -0 Normal operation switching controller is working. All LDs go out as soon as the setpoint is reached. The LD ower is illuminated. NRS -0 NRS -0 ress button briefly. The test mode (relay test) is now active for 5 seconds. NRS -0 Hold down button. LD goes out. A alarm is simulated for switchpoint. NRS -0 Hold down button. LD goes out. A alarm is simulated for switchpoint. NRS -0 0

31 Alarm NRS -0 There are two alarm conditions: n High-level alarm ( alarm) n Low-level alarm ( alarm) NRS -0 High-level () alarm LD changes after the de-energizing delay from rapid flashing to lighting. flashing illuminated Low-level () alarm LD changes after the de-energizing delay from rapid flashing to lighting. flashing illuminated

32 Malfunctions Fault-finding list for troubleshooting Device fails to work indication of malfunction Fault: In spite of correct wiring and commissioning of the equipment an interference signal is indicated. Remedy: The interference signal is caused by H. F. interferences coming from the installation. For interference suppression of the voltage supply we supply ferrite rings, stock code 75. The 0 V supply lines should be looped through the ferrite ring five to ten times. If several controllers are used in the system, they can be fed from the interference suppressed supply lines. For the intererence suppression of the bus line we supply hinged-shell ferrite rings, stock code 75. The hinged-shell ferrite rings are clamped onto the bus line close to the terminal strip of the controller. Device fails to work no function Fault: LD ower does not light up. Remedy: Apply power. Connect the equipment according to the wiring diagram. Device does not work properly Fault: Incorrect function at analogue output. The following actual value indicator shows incorrect values. Remedy: Correct the switchpoint settings and the active measuring range settings of the electrode. Fault: Switchpoints and actual value indication drift continuously towards 00 %. Remedy: Deposits have accumulated on the electrode rod. Remove the level electrode and clean the electrode rod. Fault: A high-level alarm is raised although the liquid level is below high level. Remedy: Deposits have accumulated on the electrode rod: Clean the electrode rod. Defective electrode insulation: Replace level electrode. Fault: Liquid level below switchpoint low level, device fails to switch. Remedy: Check installation of level electrode and vent hole in the protection tube. If an external measuring pot is used make sure to open the isolating valves. Fault: High-level switchpoint exceeded no indication. Remedy: Level switch defective. Replace equipment. If faults occur that are not listed above or cannot be corrected, please contact our service centre or authorized agency in your country.

33 System Malfunctions Danger The terminal strip of the equipment is live during operation. This presents the danger of electric shock. Cut off power supply before mounting or removing the terminal strips or the housing cover. NRS -0 Faulty installation and/or configuration of CAN bus components, excessive temperatures in the devices, defective electronic component parts or electromagnetic interferences of the supply system can result in system malfunctions. In the event of a system malfunction the safety circuit (terminal 5 and 9) is instantly interrupted. There are four system malfunctions that might occur in the level electrode and the switching controller. n Max. admissible temperature in electrode terminal box exceeded n No or faulty communication between controller and electrode n Fault in CAN bus n Failure of V power supply unit built in switching controller NRS -0 The automatic self-testing routine checks the switching controller every seconds and the sensors (e.g. the level electrodes) every 0 seconds. During each self-testing routine the error messages will be stored in the switching controller. The error messages remain stored until the cause of the fault(s) is eliminated. If a malfunction is detected the signal output of the switching controller (terminals 7 and 8) will be opened and closed as a function of the triggering pulse. As part of the automatic selftesting routine the function of the output relays will also be checked every 6 hours.

34 System Malfunctions continued Danger The terminal strip of the equipment is live during operation. This presents the danger of electric shock. Cut off power supply before mounting or removing the terminal strips or the housing cover. Systematic malfunction analysis The sources of malfunctions occurring in CAN bus systems operating with several bus-based stations must be analysed systematically since faulty components or incorrect settings can give rise to nega tive interactions with intact bus devices in the CAN bus system. These unwanted interactions can cause error messages in fully functional bus devices, which will make fault detection even more difficult. We recommend the following systematic fault finding procedure: Step (Start) Detach terminal strips in all sensing units of bus devices. Level electrode Conductivity electrode ressure sensor Temperature sensor etc. Check Use fault-finding list to correct fault(s)! Final test: have all faults been eliminated? Step lug in terminal strip of the sensing unit of one system, e. g. NRS... and NRG... (sensor). Check next system System Malfunction Use fault-finding list to identify the fault(s). Cut off power supply to the equipment. Step Apply mains voltage to bus devices of the system, e. g. NRS... and NRG... System O.K. Detach terminal strips between bus devices of the system, e. g. NRS... and NRG...

35 System Malfunctions continued System malfunction LDs flashing slowly The four indicator LDs flash slowly. High/low-level alarm NRS -0 Fault: The max. admissible temperature in the electrode terminal box is exceeded. Remedy: Insulate electrode flange to protect the equipment against heat radiation. As soon as the temperature drops below the max. admissible limit the equipment automatically returns to normal operation. System malfunction LDs flashing rapidly The four indicator LDs flash rapidly. High/low-level alarm NRS -0 Fault: The CAN bus line between the nodes is interrupted. Remedy: Check wiring and terminals. Restart system Fault: Incorrect node ID(s). Remedy: Set correct nodes ID(s), referring to section Basic Adjustments or Annex. Disconnect the system from its power supply. After 5 sec. apply power and restart system. 5

36 System Malfunctions continued System malfunction LD Bus status flashes slowly. NRS -0 LD flashing slowly Fault: Abhilfe: Malfunction in CAN bus. Restart system. LD Bus status flashes slowly. High/low-level alarm NRS -0 LD flashing slowly Fault: Data transfer in CAN bus interrupted. Remedy: The bus cables have to be correctly connected according to the wiring diagram (observe polarity!). Make sure that all end-of-line nodes are provided with 0 Ω terminating resistors, referring to the wiring diagram. Disconnect the system from its power supply. After 5 sec. apply power and restart system. Fault: The baud rate of one or more nodes is not set correctly. Remedy: Check baud rate settings of all bus nodes. The baud rates must be identical. Refer to section Annex for more details. Disconnect the system from its power supply. After 5 sec. apply power and restart system. Fault: The overall length of the bus cable does not correspond to the selected baud rate. Remedy: Change baud rate settings of all nodes according to the indications specified in Annex. Disconnect the system from its power supply. After 5 sec. apply power and restart system. 6

37 System Malfunctions continued System malfunction LD ower flashes slowly. NRS -0 LD flashing slowly Fault: The power supply unit (SU) is overloaded and may be misused for other components. Remedy: Check load of power supply unit. Be sure to use the SU only for the voltage supply of bus-based network components. Disconnect the system from its power supply. After 5 sec. apply power and restart system. Fault: ower supply unit defective. Remedy: Replace power supply unit. 7

38 Decommissioning Disposal Danger The terminal strip of the equipment is live during operation. This presents the danger of electric shock. Cut off power supply before mounting or removing the terminal strip and the housing cover. Remove the equipment and separate the waste materials in accordance with the material specification. lectronic components (boards) must be disposed of separately. For the disposal of the equipment observe the pertinent legal regulations concerning waste disposal. Annex Note regarding Declaration of Conformity / Declaration of Manufacturer For more information on the conformity of the equipment to uropean directives, please refer to our Declaration of Conformity or our Declaration of Manufacturer. You can ask for a copy of the current Declaration of Conformity / Declaration of Manufacturer or you can find them at 8

39 For your notes 9

40 Agencies all over the world: AG Münchener Straße Bremen Germany Telefon Telefax mail Web /07-07cm ( ) AG Bremen rinted in Germany 0