ONSIP O2IR56B1. Rev.1.3 (June, 2013) 1

Transcription

1 ONSIP O2IR56B1 Rev.1.3 (June, 2013) 1

2 Directions Be careful not to cause any physical damage by dropping or throwing O2IR56B1. Especially keep the device out of reach from children. Do not disassemble O2IR56B1. No after service is assumed when disassembled. Use only the power adapter provided with O2IR56B1. Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when installing O2IR56B1. The screw holes for the installation screws and pipe should be maintained water tight during the whole lifetime of the product. All the electrical connection wires running into the unit should be prepared so that water from the outside cannot flow into the unit through the surface of the wires. Penetration of the moisture through the wire for extended period can cause malfunction of the unit or deteriorated image. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into and outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/tv technician for help. Rev.1.3 (June, 2013) 2

3 Caution Any changes or modifications in construction of this device which are not explicitly approved by the party responsible for compliance could void the user s authority to operate the equipment. Revision History Date Revision Details First manual revision creation Text revision Contents revision; System requirements revision; Additional text revision June, 19 th, Updated package contents, drawings Rev.1.3 (June, 2013) 3

4 Contents Contents Introduction Overview Specification Applications of O2IR56B Product Description Contents Product Preview Physical description Functional Description Accessories for installation On Site Installation Bracket Getting Started PC Requirement Quick Installation Guide Troubleshooting No power is applied Cannot connect to the Video Windows Vista or Windows Technical Assistance Appendix OSD Menu Control MENU Set Up LENS Exposure Backlight Day / Night White Balance DNR(Digital Noise Reduction) Image Motion System Exit Rev.1.3 (June, 2013) 4

5 1. Introduction 1.1. Overview The O2IR56B1 is a dual-codec (H.264, MJPEG) IP/network camera built with embedded software and hardware technology. It enables real time transmission of synchronized video of up to 1080p and audio data. Remote clients can connect to O2IR56B1 for the real time video/audio data through various client solutions running on PC or smart device. Real time 2-way communication is available through the bidirectional audio communication feature. Designed to be a stand-alone streaming audio & video transmission device, O2IR56B1 can be applied to various application area such as video security, remote video monitoring, distance education, video conference or internet broadcasting system. IP-67 compliant vandal proof housing will extend the application area to harsh environments of wide temperature range. Rev.1.3 (June, 2013) 5

6 1.2. Specification Category Sub-Category Details Video Compression H.264 / MJPEG Resolution * Refer to the datasheet. Camera Module Mounting Gimbal 3 Axis Gimbal Audio (Bi-directional) Up 32 Kbps G.726 Down 128 Kbps PCM Network Interface Access network Application RJ-45, 10/100 Mbps Static, DHCP, PPP/PPPoE RTP, RTSP, SMTP, FTP, HTTP, SDP, NTP, DNS Sensor In 1 NC, NO Selectable Relay Output 0 N/A I/O Power Supply Housing RS-232C Mic/Line In Line Out PoE DC Adapter N/A Selectable in Admin page 1 V p-p output for amplified speaker Power over Ethernet 12V DC adapter (1.5 Amp) IP67 compliant Vandal Proof housing Mounting Bracket, Mounting Wall, Ceiling Motion Detection 3 zones Arbitrary shape with independent sensitivity Upgrade Administration Firmware upgrade over IP network Remote administration over IP network Client & Viewer Web Viewer SPECO NVR 3rd Party VMS Simple viewing over internet explorer Standard VMS software Ask provider for details Dynamic IP support DDNS support Supported Video/Audio stream encryption Security ID and Password protection IP filtering for restricting administrative access for audio and bi-audio Rev.1.3 (June, 2013) 6

7 Time management SDK support Sync to PC Manual Internet Time Server Active-X HTTP Synchronize to PC Manual time setting Synchronize to Time Server 1.3. Applications of O2IR56B1 Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc.) Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.) Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting Weather and environmental observation Rev.1.3 (June, 2013) 7

8 2. Product Description 2.1. Contents The product package contains the following: Contents Description Remarks O2IR56B1 O2IR56B1 main unit Bracket included Tools and Mounting Screws CD L-Wrench 2EA, Video Cable 1EA, Screw(5x10 4EA / 8x25 4EA), Round Base Bracket Adaptor 1EA Software & User s Guide Quick Reference Guide Quick installation guide Rev.1.3 (June, 2013) 8

9 2.2. Product Preview O2IR56B1 IP Installer VMS Software (Speco NVR) Weatherproof Bullet IP Camera PC software to allocate an IP address to the IP Camera PC software to view and record the A/V streaming data transmitted from IP camera. (Simultaneous support of up to 64 IP Rev.1.3 (June, 2013) 9

10 2.3. Physical description External View Connector information Rear Figure 2-1. External view of O2IR56B1 LAN Power Sensor Audio-Out Audio-In Figure 2-2. Connector information Rev.1.3 (June, 2013) 10

11 Focus control SD card Factory default Figure 2-3. Factory Default switch and Video output connector 2.4. Functional Description DC 12V: Power input for supplying 12V DC power. MIC/LINE IN Connect external audio source or microphone. Line Out Connect speakers with built in amplifier. Audio from remote site is output through Line out in bidirectional audio mode. 100Base-T 100Mbps Ethernet connector (RJ-45) Alarm In/Out and Audio In Used for connecting alarm sensor, microphone and speaker to O2IR56B1. Description LINE OUT (+) MIC/LINE GND (-) MIC/LINE IN (+) SENSOR IN SENSOR IN GND 1 V p-p audio signal output for amplified speaker. Ground for audio signals. Audio input: Can be used either for microphone or applying audio signals from other audio equipment. Sensor In (+). NC/NO selectable in admin mode. Ground for sensor SENSOR IN Connect external alarm sensor. Examples of sensing devices are infrared sensor, motion sensor, heat/smoke sensor, magnetic sensor, etc. Connect the two wires of the sensors to SNS In. Rev.1.3 (June, 2013) 11

12 The sensor type (NC/NO) can be set in the admin page. Multiple sensor devices can be connected in parallel. Photo Coupler NO/NCType Open CollectorType Sensor1+ Sensor Device Sensor Device +12V GND Sensor1- Sensor Power Supply Sensor Power Supply Figure 2-4. SENSOR input and connection of the sensor Factory Default Switch A switch provided for returning the IP camera to the factory default state. Open the dome cover to access the switch. Press the switch for a few seconds while power is applied. Factory default Figure 2-5. Factory Default Switch Rev.1.3 (June, 2013) 12

13 2.5. Accessories for installation Figure 2-6. Accessories for installation of O2IR56B1. Rev.1.3 (June, 2013) 13

14 3. On Site Installation Use Cables and conduits that are suitable for the installation and that are compliant to IP-67. Particular attention should be paid in the installation so that no moisture is allowed to penetrate into the unit through the cables or conduits during the lifetime of the product. Products of which the internal parts are exposed to moisture because of improper installation are not covered by warranty Bracket Figure 2-7. Bracket installation 1. Make a suitable hole for cabling 2. Connect the cables. 3. Fix the Base on the wall 4. Adjust the position of the lens for desired viewing of the site. 5. Adjust the focus Rev.1.3 (June, 2013) 14

15 4. Getting Started Brief information for the initial operation of O2IR56B1 is provided in this chapter PC Requirement Audio/Video streaming data received from O2IR56B1 can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below: Minimum Requirement Recommended Specification CPU Intel Core i3 3Ghz Intel Core i7 Main Memory 2GB 4GB Operating System * Windows XP Windows 7 (64bit) Web Browser Internet Explorer 8, 9 Internet Explorer 8, 9 Graphic Card Video RAM 256MB Resolution 1920x1080 Video RAM 1GB Higher than 1920x1080 Network 100 Base-T Ethernet 100 Base-T Ethernet Rev.1.3 (June, 2013) 15

16 4.2. Quick Installation Guide 1. Connect PC and O2IR56B1 to the network. 1) Prepare a PC to run programs for the installation and video connection (PC is needed to assign an IP address to O2IR56B1) 2) Connect O2IR56B1 as shown in dotted line in Figure 4-1. DC power is applied through a DC power adapter. DC adapter LAN switch Figure 4-1. Power and network connection 2. Install Speco-NVR Speco-NVR is a multi-channel VMS program for the IP camera or Video server. Install Speco-NVR on remote PC to connect to these products. It is needed to assign connection information to Speco-NVR program before connection. Insert the CD provided with product into the PC and install Speco-NVR. Admin Page Button IP installer Figure 4-2. Speco-NVR Follow the sequence below for setting the IP parameter i) Run IP installer ii) Click (1) in IP installer window.> Double click on (2) > Fill in (4) > make a selection in (5) > Fill the parameters in (6) iii) Click on (9) to apply the settings. iv) You can connect to the admin page by clicking on (10). Rev.1.3 (June, 2013) 16

17 Click on the field in (3) for sorting and rearranging the list. Select network mode that best suits from the drop down list in 5. You can choose either Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in 6 are deactivated. In case of ADSL, fill the User Name and Password in 8 with the values provided by your ISP. If DDNS service is needed, Check at the box and fill the empty field with hostname you want in 7. Rev.1.3 (June, 2013) 17

18 3. Remote video connection to O2IR56B1 1) Connection through Web Viewer Web Viewer offers the simplest way of video connection to O2IR56B1. For video connection, enter the IP address of O2IR56B1 in the URL window of Internet Explorer as: [e.g.] Port 80 Port 80 (default) can be omitted [e.g.] Port 8080 Note: Active-X module should be installed on your PC before actual connection. If your PC is not connected to the internet, you cannot download Active-X module. Most convenient way of installing the Active-X module is installing Speco-NVR which is available from the CD or our web site. Connection to Admin Page Basic Control Buttons Video Crop Control Figure 4-3. Web Viewer Default ID and password of Admin Page are admin, For more detailed information, please refer to the [Configuration_Guide] Guide. 2) Connection through Speco-NVR Click the camera assignment button for setting camera address. Input the description, address, Ch#, User ID, Password and port and then click the save button. After assignment procedure, you must click the SAVE button. You can see the live video when you click the live view button as below. When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for Speco-NVR can be found in [Speco-NVR User s Guide]. Rev.1.3 (June, 2013) 18

19 Camera Assignment Live view Exit Program Default ID/PW: admin/1234 Camera Assignment Example Save Figure 4-4. Speco-NVR 4. Additional settings through connection to the Admin Page All parameters of the camera are factory default out of the box. For a more sophisticated target application, parameters need to be changed through the admin page. The admin page can be connected through /admin.htm ID and password of the administrator are required. Default ID and password are admin, It is highly recommended to change the ID and password to prevent illegal access to the IP camera. For more detailed information, please refer to the [Configuration_Guide] Guide. Rev.1.3 (June, 2013) 19

20 5. Troubleshooting 5.1. No power is applied In case of Standard PoE (Power over Ethernet) Power supply through standard PoE is possible only when the following conditions are met. 1. Standard PoE is supported on the product. 2. The LAN switch supports standard PoE. Make sure that both the IP camera and the LAN switch support standard PoE (IEEE 802.3af) In case of DC adapter If PoE is not applied, the power and network connection should be made through separate cables. It is recommended to use DC adapter supplied by provider for the feeding of the power. In case of replacing the DC power supply, make sure that the power supply meets with the power requirement of the IP camera to prevent damage or malfunction Cannot connect to the Video Check the status of the network connection through a PING test. Try the following on your PC: - Start > Run > Cmd > Ping IP address (Ex : Ping ) - If Reply from ~ message is returned ( 1 in the figure below), the network connection is in normal state. Try connection to the video again. If the problem persists, or refer to other trouble shooting notes. - If Request timed out message is returned. ( 2 in the figure below), the network connection or network setting is not in normal state. Check the network cable and settings. 1 2 Rev.1.3 (June, 2013) 20

21 5.3. Windows Vista or Windows 7 Windows Vista and Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video captures in Speco NVR and Web Viewer. <Windows Vista> 1. UAC (User Access Control) configuration 1) Double-click User Accounts in control panel 2) Double-click Turn User Account Control on or off 3) Uncheck Use UAC to help protect your computer 2. Privilege Level Control 1) Select NVR icon on the desktop 2) Click right mouse button and select Properties 3) Check Privilege Level in Compatibility tab Rev.1.3 (June, 2013) 21

22 <Windows 7> 1. UAC (User Access Control) configuration 1) Double-click User Accounts in control panel 2) Double-click Change User Account Control setting 3) Set to Never notify 2. Privilege Level Control 1) Select NVR icon on the desktop 2) Click right mouse button and select properties 3) Check Privilege Level in Compatibility tab Rev.1.3 (June, 2013) 22

23 Rev.1.3 (June, 2013) 23

24 5.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5. Error message Rev.1.3 (June, 2013) 24

25 6. Appendix OSD Menu Control 6.1. MENU Set Up 1. Press the SET key to access the menu mode. 2. Select the desired feature by using the UP/DOWN direction (/\ \/) of the SET key. If an ENTER arrow is displayed next to the feature, press the SET key to access the feature's menu. 3. If there is a setting for this feature on the right side of the screen, use the LEFT/RIGHT direction to switch between the settings and confirm your choice by pressing the SET key. 4. When the settings are completed, go to EXIT to save and leave the OSD LENS If you are using a lens with manual Iris, set this item to MANUAL. If you are using a DC controlled lens, set it to DC. If you choose DC, you will be able to select if the camera is used indoors or outdoors. The lens and shutter control will be automatically optimized according the present situation. - MODE [INDOOR, OUTDOOR] : If you choose INDOOR, the Iris and the shutter are set to fixed values. This will prevent a rolling effect of the image. If you choose OUTDOOR, the Iris and shutter settings are flexible and will adjust accordingly to the current brightness situation Exposure When selecting, the following submenu will appear. The exposure is the amount of light received by the image sensor and is determined by the width of lens diaphragm opening, the amount of exposure by the sensor (shutter speed) and other exposure parameters. With this item, users can define how the Auto Exposure function. Rev.1.3 (June, 2013) 25

26 BRIGHTNESS [0 ~20] : This function is used to adjust the brightness of the camera picture. SHUTTER [1/25, 1/30, 1/60, 1/50, 1/120, 1/240, 1/500, 1/1000, 1/2000, 1/4000, 1/8000, 1/16000, 1/30000, 1/60000] : You can select one of 14 options from 1/25 to 1/60000K for the fixed high speed electronic shutter, which is mostly used for imaging a fast moving object. SENS-UP [OFF, AUTO, x2~x64] : Automatically detects the ambient level of darkness in a dark or low contrast scene to extend the accumulated time, keeping the image bright and sharp. AGC (Automatic Gain Control) [0-20] : The AGC (Auto Gain Control) function is used to amplify the video signal when it falls below the set parameter. As the AGC level increases, the overall screen gets brighter but the level of noise will also increase at the same time Backlight To overcome difficult light situations, the camera features different options to improve the image quality. HLC (High Light Compensation): This function is used to surpress or mask a strong light source (for example, headlights of cars during night-time) so that other subjects can be seen in more detail. If you select HLC, a submenu appears where you can make finer adjustments. - HLC LEVEL: Adjust the brightness level from which on the light source is to be masked out. Rev.1.3 (June, 2013) 26

27 BLC (Back Light Compensation): This function is used to counterbalance the screen image by increasing the brightness so that a subject which appears dark due to a strong backlight can be displayed in more detail. If you select BLC, a submenu appears where you can make finer adjustments. - H-POS/ V-POS/ H-SIZE/ V-SIZE: Define the position and size of the area of interest by changing the position & size. WDR: The WDR (Wide Dynamic Range) function works to correct excessive light within the frame to produce a usable image. When the image has simultaneous bright and dark areas, it makes both areas distinct. If you select WDR, a submenu appears where you can make finer adjustments. - WEIGHT [MIDDLE, HIGH, LOW]: Select the WDR level of the camera. * The WDR function might lead to a reduced framerate and ghost effects in areas with very bright background Day / Night Here you can choose different settings to control the DAY&NIGHT function. Rev.1.3 (June, 2013) 27

28 COLOR: The camera is always in color mode regardless of the ambient conditions. B/W: The camera is always in Black & White mode regardless of the ambient conditions. EXTERN: Here you can activate the EXTERN function to activate the external Day & Night connector on the rear panel of the camera. If you select EXTERN, a submenu appears where you can make finer adjustments. - DELAY [MIDDLE, HIGH, LOW]: Set the delay time for switching between COLOR and B/W. AUTO: The camera will automatically switch between DAY and NIGHT mode, according to the lighting condition. If you press the SET key, the AUTO sub-menu is selected. - AGC THRES [0-20]: Execute the Day/Night switch depending on the AGC level that is used to increase the brightness of the image. Higher values require a darker illumination to execute the switch. - MARGIN [0-20]: Define the difference between the Day/Night & Night/Day switch based on AGC THRES. Higher values will increase this distance and can help to prevent continuous switching between Day & Night mode. - DELAY [MIDDLE, HIGH, LOW]: Set the delay time for switching between COLOR and B/W. Rev.1.3 (June, 2013) 28

29 6.6. White Balance The camera needs to find a reference color temperature, which is a way of measuring the color of a light source, for calculating all the other colors. The unit for measuring this ratio is in degree Kelvin (K). You can select one of the White Balance Control modes according to the installation condition. ATW (Auto Tracking White Balance): With the Auto Tracking White Balance function, the white balance in a scene will be automatically adjusted while temperature color is changing. The ATW Mode is suitable for environments with a light source having a color temperature in the range roughly from 1800 ~ 10500K. AWB (Auto White Balance): In this mode, white balance works within its color temperature range. This mode computes the white balance value output using the color information from the entire screen. It outputs the proper value using the color temperature radiating from a black subject. PRESET: This mode is set to the current white balance condition and keeps its value. Select this mode and then press the SET key. If there is a change in location or light source, please repeat this procedure. MANUAL: Can be used for fine adjustment. Set the White Balance by first using ATW or AWC and then change to MANUAL and press the SET key. Increase or decrease the value of R-Gain (Red) and B-Gain (Blue) while monitoring the color of the image. - R-GAIN: Adjusts the White Balance for the color Red. - B-GAIN: Adjusts the White Balance for the color Blue DNR(Digital Noise Reduction) This function is used to improve the picture quality by filtering the noise which is generated under low bright light conditions. You can set different levels here. Rev.1.3 (June, 2013) 29

30 6.8. Image When selecting, the following submenu will appear. Here you can optimise the image quality by adjusting different options. SHARPNESS [1 ~ 10] : Adjusts the image sharpness. If the level goes up excessively, it may affect the video image and generate a noise. GAMMA [0.45 ~ 0.65] : Changes the gamma curve of the camera. COLOR GAIN [0 ~ 20] : Kontrollieren Sie die Farbsättigung des Video-Bildes. MIRROR [ON, OFF] : Mirrors the image horizontally on the screen. FLIP [ON, OFF] : Flips the image vertically on the screen. D-ZOOM [1.0x~8.0x] : You can use the up to x8 bi-cubic linear digital zoom. D-WDR [LOW, MIDDLE, HIGH, OFF] : The WDR (Wide Dynamic Range) function works to correct excessive light within the frame to produce a usable image. When the image has simultaneous bright and dark areas, it makes both areas distinct. Rev.1.3 (June, 2013) 30

31 SHADING [ON, OFF] : Compensates the shading effects of lenses when the lens is set to a very wide angle. This function will reduce the brightness difference between the centre and the edges. If you select ON, a submenu appears where you can make finer adjustments. - WEIGHT [1%~100%] : You can set different levels here. PRIVACY [ON, OFF] : Masks areas that you want to hide on the screen. The camera can activate up to 32 privacy masks. Switch between ON and OFF to activate or deactivate this function. - ZONE NUM [0 ~ 32]: Select a mask out of the 32 mask areas and set the options below for the selected mask. - ZONE DISP [ON, OFF]: Choose ON to activate privacy masks and press OFF to deactivate masks. - H-POS [0 ~ 60]: Define the horizontal start position of the privacy mask. - V-POS [0 ~ 40]: Define the vertical start position of the privacy mask. - H-SIZE [0 ~ 40]: Define the horizontal size of the privacy mask. - V-SIZE [0 ~ 40]: Define the vertical size of the privacy mask. - Y LEVEL [0 ~ 20]: Define the brightness of the mask color. - CR LEVEL [0 ~ 20]: Define the red amount of the mask color. - CB LEVEL [0 ~ 20]: Define the blue amount of the mask color Motion This function is used to detect moving objects in the monitored area. When choosing ON, the following submenu will appear where you can adjust the settings for the MOTION function. Rev.1.3 (June, 2013) 31

32 SENSITIVITY [1 ~ 20] : Set the sensitivity of the motion detection. DET H-PS [0 ~ 60] : Define the horizontal start position of the monitoring area. DET V-PS [0 ~ 40] : Define the vertical start position of the monitoring area. DET H-SIZE [0 ~ 60] : Define the horizontal size of the monitoring area. DET V-SIZE [0 ~ 40] : Define the vertical size of the monitoring area. MOTION OSD [ON, OFF] : Controls the ON/OFF status of the motion detection block display. ALARM [ON, OFF] : When the ALARM function is activated, the camera will detect movement within a monitoring area and then send an alarm signal automatically. The flash warning notice "MOTION!!!" will be displayed in the upper left corner of the screen. When the camera is moved, the flash warning notice "MOVING!!!" will be displayed in the upper left corner of the screen System When selecting, the following submenu will appear. COLOR SPACE [COLOR1~3] : Select different color settings for a warmer or a colder image. Rev.1.3 (June, 2013) 32

33 FRAME RATE [25 FPS, 30 FPS] : Choose a frame rate. CVBS [PAL, NTSC] : Select the video format that matches the present TV system RESET [ON ] : All settings will be restored to factory default. Press the Set button in the exit menu to save the current settings and exit the Set Up menu Exit Press the Set button in the exit menu to save the current settings and exit the Set Up menu. Rev.1.3 (June, 2013) 33