Built-Up Pocket Door Frames 1750 Series For 1 1/8 to 1 3/8 Doors Maximum Door Weight 150 lbs.

Transcription

1 Built-Up Pocket Door Frames 1750 Series For 1 1/8 to 1 3/8 Doors Maximum Door Weight 150 lbs. Pocket Door Frames pen up rooms, creates more space and provides privacy. You can do it all with A&F Wood Produtcs Pocket Door Frames. Where a traditional swinging door would use up too much space, pocket doors fit right in to solve room planning problems. You get more usable space, more flexibility and better appearance. Installation is approximately 20 minutes, using just a few basic tools. Pocket Door Hardware A&F Wood Products offers a snap-in track and hanger system. Larger wheels and heavier gauge steel body design. *Four wheel ball bearing hardware is available to hold up to 250 lbs. Pocket Door ptions Miscellaneous options are available to customize your Pocket Door Frames. You can order separately Mullion Kits, Extension Kits, Jamb Kits and more. Stock is available in 4/0 widths, 7/0 & 8/0 heights as well as options for 2x6 walls, 5/8 drywall, and 13/4 doors. Built-Up Frames Fully assembled for quick and easy installation. All frames are designed to hold up to 150 lbs. for a standard 6 8 door PF101

2 K.D. Pocket Door Frames 2000 Series For 1 1/8 to 1 3/8 Doors Maximum Door Weight 150 lbs. Pocket Door Frames pen up rooms, creates more space and provides privacy. You can do it all with A&F Wood Produtcs Pocket Door Frames. Where a traditional door would use up too much space, pocket doors fit right in to solve room planning problems. You ge more usable space, more flexibility and better appearance. Installation is approximately 20 minutes, using just a few basic tools. Pocket Door Hardware A&F Wood Products offers a snap-in track and hanger system. Larger wheels and heavier gauge steel body design. *Four wheel ball bearing hardware is available to hold up to 250 lbs. Pocket Door ptions Miscellaneous options are available to customize your Pocket Door Frames. You can order separately Mullion Kits, Extension Kits, Jamb Kits and more. Stock is available in 4/0 widths, 7/0 & 8/0 heights as well as options for 2x6 walls, 5/8 drywall, and 13/4 doors. K.D. Frames ne size fits all up to 3/0 s, Knock Down Frames you can cut to size for your customize opening. Each K.D. is designed to hold 150 lbs. standard 6 8 door PF102

3 Built-Up Pockets 150 lb. & 250 lb. Pocket Door Hardware Specifications For installation of pocket or bi-parting doors up to 4 wide, 1 to 1-3/8 thick panels weighing up to 150 lbs. each and up to 8 high. Heavy gauge, steel stiffener reinforces split jambs. Four large 1 wheels for easy rolling action. Easy to install feature makes installation a snap. Supports panels weighing up to 150 lbs. Easy adjustment after installation. V-groove jump proof aluminum track. pening width equals door width multiplied by 2, add 2. For Bi Part: Sum of 2 doors multiplied by 2, add 2. For 6 8 Door: Height equals 84 from finished floor. For 7 0 Door: Height equals 88 from finished floor. For 8 0 Door: Height equals 100 from finished floor. Built-Ups can be ordered in 6 8, 7 8, or 8 0 door height. PDFC150N conforms to ANSI A type D8681 Cross Reference: Stanley 1750, Cox , Grant 7000 Series, Hager 9601/9701, Johnson 100, Lawrence 506/580 Track, Sterling 1601 Series. 250 lb. heavy duty hardware has four large 1 ball bearing wheels for easy rolling action. Support panels weighing up to 250 lbs. Complete Set: ne set consists of: 1 Track, 1 pair of Hangers, 2 Guides, 1 Bumper and 1 Wrench. WRENCH Wrench SPLIT FLR GUIDE 1 - Splitfloorguide BUMPER Bumper (already attached on Built-Up) HANGER HDW TRACK Track PF103

4 K.D. Pockets 150 lb. & 250 lb. K.D. Pocket Door Specifications For installation of pocket or bi-parting doors up to 3 width, weighing up to 150 lbs. each and up to 8 high Heavy gauge, wrap around steel stiffener reinforces split jambs Four large 1 wheels for easy rolling action Easy-to-install feature makes installation a snap Supports panels weighing up to 150 lbs. Cut marks on header make for easy sizing Easy adjustment after installation Cut marks on header make for easy sizing Non-handed steel header brackets for easy leveling of header assembly V-Groove jump proof aluminum track pening width equals door width multiplied by 2, add 1 1/4 For Bi Part: Sum of 2 doors multiplied by 2, add 1/4 Kits are sized for 3 0 door width and can be cut shorter at installation For 6 8 Door: Height equals 84 1/2 from finished floor For 7 0 Door: Height equals 88 1/2 from finished floor For 8 0 Door: Height equals 100 1/2 from finished floor Kits are sized for 6 8, 7 0, or 8 0 door height and can be cut shorter at installation PDFC150N conforms to ANSI A type D8671 Cross Reference: Stanley 735/ R/ , Crowder Crowderframe, Hager 9630/9631, Johnson 1500, Sterling lb. heavy duty hardware has four large 1 ball bearing wheels for easy rolling action. Supports panels weighing up to 250 lbs. Complete Set: ne set consists of: 1 Header Track, 2 Floor Plates, 1 Wrench, 2 Guides, 1 End Bracket, 1 Bumper, 1 Hanger, 2 Jamb Studs WRENCH Wrench BUMPER Bumper HEADER TRACK 1 - Header FLR PLATE SPLIT FLR GUIDE 2 - Floorplate 1 - Splitfloorguide END BRACKET 2 - Bracket HANGER HDW JAMB STUDS 1 - Jamb PF104

5 Converging Door Kit/Mullion Connector Instructions For Joining two #1750 Buil-Up Pockets or two #2000 Series K.D. Pocket Door Frames Step 1: Prepare Rough pening: Built-Up: 4 x Door + 2 Sample: 30 Door x = 122 K.D.: 4 x Door + 1/4 Sample: 30 Door x 4 + 1/4 = 120 1/4 Step 2: Built-Up: Cut 3/4 off opening end of header assembly, cut ends square to keep header straight. KD 1 Built-Up 3/4 K.D.: Cut 1 off opening end of header assembly, cut ends square to keep header straight. Step 3: Butt cut ends together and fasten using brackets in this kit as illustrated. Drill 1/4 holes for the 2 machine bolts and one in the center for lag screw. Step 4: Hang combined assembly and fasten to rough header with center lag screw. Adjust to level. Step 5: Install center stop bumper into ends of track. Final adjust after doors are in place. Step 6: Continue to install doors per instructions with Pocket door Frame PF105

6 Jamb Kit Instructions Fits all Built-Up and K.D. Pocket Door Frames #1755 Clear Pine Jamb Kit #1756 Paint Grade Pine Jamb Kit Pre-sanded jamb kits are available in stain or paint grade pine. Simply, cut to length and install. Jamb kits fit all standard 2x4 wall applications with 6 8 doors. Installation Instructions: 1. Install Pocket Door Frame according to instructions. nce drywall is installed around unit, measure height A (from floor to bottom of frame header). 2. pen door fully so door is extended into opening. Cut split jambs to B. Fasten to front edge of frame. Maintain minimum 3/16 clearance on both sides of door. Raise or lower hanger to plumb door with split jambs. 4. Cut split headers to C. Determine side of hangers with lock arm and fasten this header with screws for easy removal. Nail other side. Maintain 3/16 on each side of door. 5. Fasten bottom door guides so door stays in center of pocket and travels easily without bindings. 6. Finish with your choice of casings (not included). 3. Shim and plumb strinke jamb (wide piece) with door PF105A

7 Extention Kit #1752 & #1753 Instructions Built-Up Pocket Door Frame Fits all Built-Up Pocket Door Frames Installation Instructions Step 1: Step 2: Prepare Rough pening (Special Dimensions) Nominal Door Size Equation A R Door + 4 = Door + 4 = 100 Slip back extension over the top of the basket back. Then screw into basket on both sides of back with #6 x 1 screws. Step 3: Slip split jamb extension on the top of the basket split jamb. Steel on top of basket will fit under 4 split jamb material. While aligning and butting wood together, screw directly into steel and wood from the back side with #6 x 2 screws. Step 4: Continue with Step 2 on pocket instructions PF106

8 Extention Kit #752, #753 & #754 Instructions K.D. Pocket Door Frames Fits all K.D. Pocket Door Frames Installation Instructions Step 1: Prepare Rough pening (Special Dimensions) Nominal Door Size Equation A R Door + 4 1/2 = 88 1/2 8 0 Door + 4 1/2 = 100 1/2 9 0 Door + 41/2 = 112 1/2 Step 2: Step 3: Step 4: Prepare Split Members: Push wood filler out of steel split member 8. (Split members supplied in pocket door frame.) Cut wood off flush with steel. (Repeat on remaining split members. Four per pocket.) Install Extenders: At opposite end of cut, insert extenders. Continue with pocket frame installation Instructions PF107

9 PF108

10 Step 3. Knock the wall studs out of place with a 3-lb. Maul. The nails will bend when you hit the studs. Remove the floor plate too PF109

11 2000 K.D. Pocket Door Frame Assembly and Installation Instructions For any Doors weighing up to 150 lbs. We Supply: 1 Header and Track Assembly 4 Jamb Stiffeners 2 Floor Brackets 1 Snap-in Door Plates 1 Snap-in Hangers 1 Bumper 1 Wrench Fasteners 12 1 _ (3.81 cm) Screws 2 1 (2.54 cm) Screws 3 5/8 (1.59 cm) Screw 18 2 (5.08cm) Nails Bi-parting Bracket applications requires A 741 bi-parting bracket (not included) Step 2: Cut Header Assembly 1. The header assembly does not require cutting if your Door panel width is 36 (91 cm). For shorter widths, cut Header assembly as follows. Determine width of Door. Cut Nailing Strip at the premarked size indicators. If your Door dose not correspond with pre-marked sizes (go to Step 3). 2. Cut Track 2 shorter than Header to allow for end Bracket. NTE: Header assembly pre-marked Door width. Header markings accommodate inside Trim of Pocket. Step 3: For dd Size Doors These frames will accommodate the following doors 6/8 (203.2 cm) ( cm) 150 lb (68 kg) 7/0 (213.4 cm) ( cm) 150 lb (68 kg) 8/0 (243.8 cm) ( cm) 150 lb (68 kg) Step 1: Prepare rough opening. Finish Floor to Rough Header height should be minimum of (A) see Table and Figure 1. Determine width of rough opening by multiplying door width by 2 and adding 1-1/4 (31.8 mm). Example: For a cm) wide door, the rough door opening width is (30 x2) + 1-1/4 = 61-1/4. (66.20cm x 2) mm = cm). A. Cut the nailing strips to the size of the door panel width plus 7/8 (2.22 cm). Cut and remove excess strip X from the middle of the assembly, not from the end. B. At the other end, cut header Y to remove twice the amount X in step A. Cut the track 2 (5.08 cm) shorter than the header. Example: For a 26 (66.04 cm) door Nailing Strip is cut to 26-7/8 (68.25cm) Excess Nailing Strip X is 9-1/8 (23.18 cm) Excess Header Y is 18-1/4 (46.36cm) Cut Track 2 (5.08 cm) shorter Step 4: Install End Bracket Use 2 5/8 (1.6 cm) screws Door A A B Bi-parting Bracket /2 (214.6 cm) 83-1/2 (212.1 cm) 80-1/8 (203.5 cm) /2 (224.8 cm) 87-1/2 (222.3 cm) 84-1/8 (213.7 cm) Step 5: Install Header /2 (255.3 cm) 99-1/2 (252.7 cm) 96-1/8 (244.2 cm) PF110

12 Step 13: Install Door Doorby bylifting and andsnapping it itin in Step 6: Level the Header Assembly at the correct height and nail End Bracket to Jamb Installation is accomplished by snapping one Door Hanger and then the other. To remove door, activate tab in direction of white arrow with a flute back screw driver as shown. Step 7: Install Floor Brackets on the one side of Jamb. Ensure wood is exposed as illustrated Use 4-1-1/2 (d.81 cm) screws Step 14: Using the Wrench supplied, turn the adjustment Post so that the Door is Plumb and has proper floor clearance Step 8: Install Split Jamb and Stud Stand up split Jamb so it butts against nailing strip, with exposed wood side facing out on drywall side. Tack the top, plumb the Jamb, and then screw Bracket to the floor. Take remaining Split Jamb, slide onto the Floor Bracket prongs and nail to opposite side of header assembly. Repeat procedure for split stud positioning it in the middle pocket. Note: Split Jambs are manufactured with a slight bow. Step 15: Install Door Guide Fasten Door Guide to the split Jamb using 1 Screws with nylon guides projecting into the opening as shown. Step 9: Install Bumper Screw the Bumper to the rough Jamb at the back of pocket with 5/8 screw (1.6 cm) approximately 102 cm (40 ) from floor. Shim it out, if necessary, so that the front edge of Door will be flush with front edge of nylon Door guide. Step 10: Install Temporary Brace (ptional) Insert 1 (25mm) x 2-1/8 (54 mm) board through split Jamb and Stud as shown. Rest the board on top of the Bumper. Then nail a support leg to board as shown. (This provides added stiffness while wall material is being applied). This board will be removed prior to installing Door. The pocket may now be enclosed by applying wall sheathing, drywall, paneling, etc. as desired. Step 11: Install Hangers Step 16: Install Face Jamb The face jamb fits between the nailing strip and the rough floor. Butt the face jamb underneath the nailing strip and shim for plumb. Nail into position. Step 17: Install Door Pull (ptional) No Door Pulls are included in this kit, but you may choose from a variety of Door Pulls and Latch sets which are available through your dealer. Fasten the Hanger Plates on the top of the door panel. Hangers must be 7/8 (2.22 cm) in from the side edge, as shown Use 8 1 _ (3.81 cm) screws Step 12: Install Adjustable Bolt and Hangers Slide both Wheel Hanger assemblies into Track from the exposed end. Step 18: Install Door Trim Install Door Stop Trim (as for a Hinged Door) allowing 3/16 (5 mm) clearance between Door and Stops for possible Door warpage. Stop should be installed over Door Guide. Apply Door casing Trim as you would other Door installations. NTE: For best performance of your Pocket Door, the Track should not be painted. If you wish, a silicone lubricant may be applied for even smoother operation. A PF111

13 Bifold Track & Hardware Standard 30 lbs. Specifications 2 Door System 4 Door System 30 lb. Bifold PanelsItem Size # of Panels Units Price For installation of 2 or 4, 7/8 to 1 3/8 thick panels weighing up to 30 lbs. each Spring loaded top pivot and roller guide for easy installation Durable pre-painted track All metal components galvanized against corrosion Permanently lubricated roller guide Panel width equals known finished opening width divided by number of panels, less 1/4 pening Width equals known finished panel width plus 1/4 multiplied by number of panels Door Height equals 1 5/8 less than finished opening height BF30, BLC30 conforms to ANSI A type D8622 Cross Reference: Stanley 2800/2900 Series, Cox 43/48, Crowder CF-100, Grant 2600 Series, Henderson B Series, Johnson 1800, Sterling 9000 Standard grade bifold hardware system designed for li ghter weight doors. White pre-finished track to guide door through opening. Use with top pivot brackets on door penel. The Bottom Pivot provides vertical adjustment of doors. Slips into jamb brack at floor level and can be moved horizontally. The Guide Wheel provides door movement on the track and is spring loaded. Snuggers holds the doors snug for two or four panel doors. The Jamb Bracket is moves easily for horizontal adjustments. The Almond Plastic knob is used on the tow or four panel doors. Is easily used to open and close doors. 2 Panel Complete Packaged Contractor Sets ur doors are pre-sized to fit in standard wood and metal openings. Example: 48 x 84 pening = (4 11 3/4 x 82 1/2 ) ne set consists of: 1- Track, 1- Roller, 1- Top Pivot, 1 Pivot Lock, 1-Botom Pivot, 1- Floor Pivot Bracket, 1 Non-Mortise Lift-off Hinge, 1 four Door Aligner, Knob, Adjustment Wrench Top Pivot Bottom Pivot Guide Wheel Plastic Knob Snuggers Jamb Bracket Alligners PF112

14 Bifold Track & Hardware Heavy Duty - 75 lbs. Specifications 2 Door System 4 Door System Surface Mounted Bifold hardware for 1-1/8 to 13/4 panels up to 75 lbs each panel Commercial grade bifold hardware system designed for use with heavier than normal doors. Designed for panels up to 9/0 high. Precision extruded commercial grade aluminum track features line-design fascia to hide finger marks and scratches or to hold paint if desired. Patented tricycle hangers with large nylon 1 diameter ball bearing wheels, ride smoothly and quietly on convex shaped system facilitating easy mounting or dismount of door panels. Hangers are adjustable for height in case of settling. Floor bracket has an adjustable bottom pivot socket. System is supplied with nonmortise hinges that can be replaced with customer supplied mortise hinge gauge zinc dichromate plated steel parts. 2 Panel Complete Packaged Contractor Sets ur doors are pre-sized to fit in standard wood and metal openings. Example: 48 x 84 pening = (4 11 3/4 x 81 ) 2 Panel Complete Packaged Set 4 Panel Complete Packaged Set PF113

15 Bifold Door - 30 lbs. Assembly and Installation Instructions For Bifold 4 Panel Sets Set Contains 1-Track with Two Track Sockets 2-Bottom Pivots 2-Top Pivots 2-Jamb Brackets 2-Top Roller Guides 1-Snugger 2-Plastic Knobs 6-Bifold Non-Mortis Hinges 1-Set Door Aligners Necessary Fasteners *Track is less than opening to reduce need to cut track. You Supply Door Panel(s) as specified on the package chart, Screwdriver, Tape Measure, Drill, Clamp, Hammer. How to Install your Bifold Doors Please read the complete instructions carefully before you start installation. All instructions apply to any size of bifold door installation. The same instructions also apply to all type of door panels. 1. Door sizing Height Make doors 1 5/8 less than the net pening height. Width Divide net opening width by the number of Door panels (2 or 4) and subtract 1/4 to determine the net door panel width. For example: A 30 opening for a two door bifold requires door panels that are 14 3/4 wide. (30 2 = 15-1/4 = 14 3/4 ). A 48 opening with 4 panels requires door panels that are 11 3/4 wide (48 4 = 12-1/4 = 11 3/4 ). 2. Install non-mortise hinges to edge of doors 1 or more in thickness. Place panels of folding doors side by side with a 5/16 spacer between the panels and clamp together. Locate hinges approximately 6: from each end of doors and at their centers. The leaf position on the door is optional. Using the hinge as a template drill 3/32 holes approximately 7/8 3. Drill 7/16 diameter holes 1 7/8 deep for pivots and guides on center and 1 from the edge of door. 4. Locate the pivots and guide as shown. Tap parts into the holes with light hammer blows directly on the top of the pins. 5. Cut Track. If necessary, cut track to at least 1/8 less than the width of the finished opening. Use a fine tooth hack saw PF114

16 Bifold Door - 30 lbs. Assembly and Installation Instructions (cont d) 6. Top pivot bracket in each end of track should have pivot hole (A) closet to jamb. Fasten track to header. n two-door unit track should be firmly against jamb at guide end of track. Use track as template and mark screw locations. Drill 1/8 pilot holes to approximate length of screws. 7. Place jamb bracket so enter line is plumb with center line of track. Bottom leg should rest firmly on carpet or floor. To fasten jamb bracket, drill 7/64 pilot holes to approximate length of screws and apply fasteners. 8. To install hinged pair of doors, place pivot pin (B) in hole, lift doors (compressing pin spring) and seat bottom pin into jamb bracket slot. Compress wheel pin, swing door under track and release wheel into track channel. 9. Press self centering (4-dr) snugger into track between pairs of doors in 4 panel installations, or press (2-dr.) snugger into track between guide wheel and jamb in 2 panel installations. 10. Horizontal Adjustment: Use Phillips screw driver to reposition top pivot bracket in or out. Lift hinged pair of doors slightly to clear slot in bottom jamb bracket, move adjusting bolt in or out until doors are plumb with jamb, and reseat bolt in bracket slot. Adjust to obtain 1/8 gap between pairs of doors at center of opening (or doors and jamb in 2-door opening). Vertical Adjustment: Lift doors again and rotate adjusting wheel (D) clockwise to raise doors, counterclockwise to lower them. Adjust doors upwards for minimum clearance at the header. Reseat adjusting bolt in bracket slot being careful not to change horizontal positioning. Do not attempt to turn wheel with teeth engaged in the bracket. 11. To place knobs, drill 7/64 holes in center of guide doors about 36 from floor. 12. For 4-door installation only. Attach aligners to back of guide doors, 12 from floor. Adjust in or out in slatted holes until doors snap closed. Tighten screws. Drill 7/64 pilot holes to a depth approximately the length of screws PF115

17 Bifold Door - 75 lbs. Assembly and Instructions How to Install your Bifold Doors Please read the complete instructions carefully before you start installation. All instructions apply to any size bifold door installation. The same instructions also apply to all type of door panels. Prepare pening Carefully: Make sure corners are square, header is level and jambs are straight. 1. Cut Track to fit pening Width and fasten to header jamb with 1-1/4 Pan Head Screws. Note: Insert Parts in Track Before Mounting 2. Fasten Hinges to Doors (1606). (A) Stand pivot door on edge and mark a line at 7 from top of midpoint and 11 from the bottom. (B) Attach hinge half with pin at marks (hinge pin pointing up) with 1 flat head screws. (Note: with nylon knuckle at hinge flush against back side of door). (C) Place second door back-to-back against first door with top of doors even. Slip hinge half without pin over hinge half with pin. (D) Attach hinge half without pin to door. 3. Fasten Pivot Plates to top and bottom of doors as shown. Note: 1121 nylon locking arm must open towards rear of opening. 4. Fasten 1011 Floor Bracket to floor 9/16 from jamb face and 7/8 from jamb edge. Remove floor bracket and proceed to Step PF116

18 5. Hang Doors by (A) inserting 1001 Top Pivot into 1010 Top Pivot Socket. Lock into place with locking lever. Then (B) insert 1125 Hanger into 1121 Door Plate. Lock into place with locking arm. (C) Tilt doors slightly to allow 1011 Floor Bracket to slide under 1706 Bottom Pivot. Insert 1706 into hole of Reattach 1011 to floor 6. Mount Aligners (1808) on back side of lead doors. (4 Door Sets nly) 7. Check for Proper Door peration: clearance, alignment, adjustments, etc. should be made at this time. If adjustments are required, they can be made at Track Pivot Socket (1010) and Floor Bracket (1011). Setting, door warpage and other uncontrollable conditions may require later areadjustments. Note: Doors must be parallel with track for proper operation. 8. Attach Knobs drill 3/16 hole 36 from bottom, and in center of #2 and #3 doors. 9. ADJUST SNUBBER (1155) Close doors, slide 1155 until it touches pen doors. move #1155 1/8 closer to #1125 ant tighten PF117

19 Bipass Track & Hardware 150 lbs. & 250 lbs. 2 Door System 3 Door System 4 Door System 150 lbs & 250 lbs. Panel By-Pass Doors For installation of two bypassing doors with 1 3/8 or 1 3/4 thick panels weighing up to 150 lbs. each Large 1 wheels provide smooth rolling action Easy to install snap-in feature makes hangers a snap to install Vertical adjustments can be made after installations Supports panels weighing up to 150 lbs Durable V-groove aluminum track provides smooth, quiet operation Track spacer allows for easy installation of bypass and tripass doors Panel Width equals known finished opening width plus 1 per overlap, divided by number of panels pening Width equals known finished panel width multiplied by number of panels, less 1 per overlap Door Height equals 3 less than finished opening height For multi-panel sizing information, contact A & F Wood Products 250 lb. Large 1 Ball Bearing wheels provide smooth rolling action Supports panels weighing up to 250 lbs. 2 Door System: ne set consists of: 2- Track, 2- Spacers, 2- Hardware, 1- Floor Guide, 1- Wrench 3 Door System: ne set consists of: 2- Track, 2- Spacers, 3- Hardware, 2- Floor Guide, 1- Wrench 4 Door System: ne set consists of: 2- Track, 2- Spacers, 4- Hardware, 4- Floor Guide, 1- Wrench WRENCH Wrench SPLIT FLR GUIDE 1 - Splitfloorgu SPACER 1- Spacer HANGER HDW TRACK PF118

20 Bipass Track & Hardware 60 lbs. 2 Door System 3 Door System 4 Door System 60 lb. Panel Bi-Pass Doors For installation of 2 bi-passing doors, with 3/4 to 1 3/8 thick panels weighing up to 60 lbs. each Slotted hangers easy to adjust Self-aligning wheel system Permanently lubricated thermoplastic wheel Supports panels weighing up to 60 lbs. Vertical adjustments can be made after installation Hanger system allows for easy panel removal V-groove galvanized steel or aluminum track provides smooth, quiet operation Spring loaded top pivot and roller guide for easy installation Permanently lubricated roller guide Durable pre-painted track All metal components galvanized against corrosion Panel Width equals known finished opening width plus1 per overlap, divide by number of panels pening Width equals known finished panel width multiplied by number of panels, less 1 per overlap Door Height equals 1 3/4 less than finished opening height BPC60,PBC60APB60 conform to ANSI A type D8742; PBC60AF conforms to type D8752, BFC30 conforms to ANSI A type D Door System: ne set consists of: 1- Steel Track, 1-Pr. Hangers, 1- Floor Guide, 2-Finger Pulls 3 Door System: ne set consists of: 1- Steel Track, 2-Prs. Hangers, 2- Floor Guide, 3-Finger Pulls 4 Door System: ne set consists of: 1- Steel Track, 3-Prs. Hangers, 2- Floor Guide, 4-Finger Pulls TRACK HANGER SPLIT FLR GUIDE FINGER PULL PF119

21 Bipass Door Installation Instructions For Doors 150/250 lbs. This package contains all the necessary hardware components for complete installation of your sliding (Bi-Pass) Heavy Duty Door Set Contents Aluminum Track, Spacers Snap-in Hanters Snap in door Plates Floor Guide Fastners Wrench Facia option not included. Headroom Details Door Height= 3 less than the finished opening. How To Install (Read all steps prior to installation) Step 1 Insert (2) Hangers per track. Clip Track units together using Track Spacers one at each ed and one in the middle for Track 72 and over. See Figure 2. Position Track into opening. Pre-drill 3/32 Pilot Holes, fasten with screws provided. Secure all Screws in Track and remove plastic Track Spacers. Facia option not included PF120

22 Bipass Door Installation Instructions For Doors 150/250 lbs. (cont d) Step 2 (ptional) For easy access for hangers, same as Step #1 except Cut Track 1 less than finished opening and install Track to Header with 1 clearance at one Jamb. See Figure #4 and #5. Do Not Cut Fascia. Step 3 Position Hager Plates so edge of Hanger Plates are minimum of 5/8 from edge of door. Pre-drill 3/32 Pilot Holes. Screw Hanger Plates to top of door along center line using #8 x 1 Pan Head Screws provided. See Figure #6 Step 4 Install Floor Guide in the center of the opening plumb with center of the Track choosing hole combinations to set spaces for 1 3/8 or 1 3/4 doors. Step 5 Install Door Hangers, lift door in the upward motion, snapping the post in Hanger Plate. Turn the Post to adjust vertically for height and plumb using Wrench provided. (Do Not unscrew Post from Hanger). To remove door, activate label in direction of white arrow with a Flute back Screw Driver as shown. See figure PF121

23 Bipass 60 lbs. Installation Instructions For Steel Track - 1 3/8 doors, install 8902 or 8906 hangers on both front and rear doors. For 1 1 1/8 doors, install 8902 or 8906 hangers on front doors, 8901 or 8905 on rear doors. Aluminum Track (non-fascia) For 1 3/8 doors, install 8901/8905 hangers on front door, 8902/8906 on rear door. For 1 3/4 doors, reverse above hanger positions on doors: For 1 1 1/8 doors, install 8902/8906 hangers on both front and rear doors. Alum. Fascia Track For 1 3/8 doors, install 8902/8906 hangers on both front and rear doors. For 1-1 1/8 doors, install 8902/8906 on front door, 8901/8905 on rear door. Note: Make opening width a min. of 1 (25mm) less than set size indicated, to provide door overlap at center. Ex: For set No make opening a maximum of 47 (1.19m). With non-fascia track, track must clear fascia by (A) and shelves or drawers `by a minimum of (B). Fascia track mounts flush with front edge of head jamb. Door Size 3/ /8 1 3/8 Steel track A N/A 3/8 5/8 Alum track A 0 3/8 7/8 Shelf B 2 3/4 3 1/2 4 Step 1 - Screw track to head jamb with track centered between jambs. Allow 1 1/4 (32mm) minimum headroom at top for hardware, plus 1/4 to 5/8 (6-16mm) clearance between door and floor. To obtain this, the recommended door height is 1 3/4 (44mm) less than the finished opening height. This provides 5/16 (8mm) adjustment for plumbing to jamb. Step 2 - Hanger plate is self seating at top of door. With single wheel hangers, mount 1/2 (13mm) from edge of door; mount twin wheel hangers 1 3/4 (44mm) from edge. Place screws at arrows on hanger plate. Step 3 - Lift doors on track, installing the inside ore rear door first. Angle door aprox. 15 degrees to engage wheels in track. Step 4 - To align the doors back off on hanger screws slightly, insert screwdriver in hanger slot and adjust for height and plumb. Finally, tighten screws. Step 5 - When using adjustable floor guide (left below), insert nylon piece in metal plate slots corresponding to door size, then locate under doors at center of opening. If using one-piece nylon guide (opt.) for 1 3/8 doors only, position same as for adjustable guide PF122

24 Snap-In Track and Hanger System For Bifold, Bypass and Pocket Doors Easier installation than other Stanley or competitive models Simply lift door and snap hanger into place Unique design improves performance and handling No special handling or tools necessary to engage hanger Fewer components to handle more applications Patent pending Quick and easy as 1, 2, 3 convenient snap-in hanger for trouble-free alignment Larger wheels provide smoother, more quiet ride Track spacer facilitates installation of bypass doors Common track allows for reduced inventory and greater likelihood of having the correct product on the job when needed PF123

25 Item Description Size R.. Units List '0" x 6'8" Pocket 50" x 84" EA. Add for: '2" x 6'8" Pocket 54" x 84" EA. Johnson '4" x 6'8" Pocket 58" x 84" EA. #100 Track '6" x 6'8" Pocket 62" x 84" EA. and Hardware '8" x 6'8" Pocket 66" x 84" EA. $ '0" x 6'8" Pocket 74" x 84" EA '0" x 6'8" Pocket 98" x 84" EA For 1 3/8" Doors Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation Item Description Size R.. Units List '0" x 7'0" Pocket 50" x 88" EA. Add for: P '2" x 7'0" Pocket 54" x 88" EA. Johnson '4" x 7'0" Pocket 58" x 88" EA. #100 Track C '6" x 7'0" Pocket 62" x 88" EA. and Hardware K '8" x 7'0" Pocket 66" x 88" EA. $ E '0" x 7'0" Pocket 74" x 88" EA T '0" x 7'0" Pocket 98" x 88" EA For 1 3/8" Doors Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation D Item Description Size R. Units List '0" x 8'0" Pocket 50" x 100" EA. Add for: R '2" x 8'0" Pocket 54" x 100" EA. Johnson '4" x 8'0" Pocket 58" x 100" EA. #100 Track F '6" x 8'0" Pocket 62" x 100" EA. and Hardware R '8" x 8'0" Pocket 66" x 100" EA. $ A '0" x 8'0" Pocket 74" x 100" EA M '0" x 8'0" Pocket 98" x 100" EA For 1 3/8" Doors E Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation S p Item Description Size R.. Units List 2000 K.D. Pocket 6/8 Height '0" x 6'8" KD Pocket 49 1/4 x 84 EA. Add for: '2" x 6'8" KD Pocket 53 1/4 x 84 EA. Johnson '4" x 6'8" KD Pocket 57 1/4 x 84 EA. #100 Track '6" x 6'8" KD Pocket 61 1/4 x 84 EA. and Hardware '8" x 6'8" KD Pocket 65 1/4 x 84 EA. $ Marked for '0" x 6'8" KD Pocket 73 1/4 x 84 EA cutting to any Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation shorter length Item Description Size R.. Units List MULLI 2-2'0" x 6'8" Pocket 98" x 84" EA. $ MULLI 2-2'4" x 6'8" Pocket 112" x 84" EA. $ MULLI 2-2'6" x 6'8" Pocket 122" x 84" EA. $ MULLI 2-2'8" x 6'8" Pocket 130" x 84" EA. $ MULLI 2-3'0" x 6'8" Pocket 146" x 84" EA. $ Biparting 6'x8" Doors MULLI 2-4'0" x 6'8" Pocket 194" x 84" EA. $ Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation For 1 3/8" Doors Page PF124

26 Item Description Size R.. Units List MU 2-2'0" x 7'0" Pocket 98" x 88" EA. $ MU 2-2'4" x 7'0" Pocket 112" x 88" EA. $ MU 2-2'6" x 7'0" Pocket 122" x 88" EA. $ MU 2-2'8" x 7'0" Pocket 130" x 88" EA. $ MU 2-3'0" x 7'0" Pocket 146" x 88" EA. $ Biparting 7'x0" Doors MU 2-4'0" x 7'0" Pocket 194" x 88" EA. $ Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation For 1 3/8" Doors Item Description Size R.. Units List MU 2-2'0" x 8'0" Pocket 98" x 100" EA. $ P MU 2-2'4" x 8'0" Pocket 112" x 100" EA. $ MU 2-2'6" x 8'0" Pocket 122" x 100" EA. $ C MU 2-2'8" x 8'0" Pocket 130" x 100" EA. $ K MU 2-3'0" x 8'0" Pocket 146" x 100" EA. $ Biparting 8'x0" Doors E MU 2-4'0" x 8'0" Pocket 194" x 100" EA. $ T Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation For 1 3/8" Doors D Item Description Units List JAMBKIT 1755 Jamb Kit Clear Pine EA R Used for finish pocket door entry Cut to length for easy installation F Can be stained or painted R A M E Item Description Units List S JAMBKIT 1756 Jamb Kit Paint Grade EA Used for finish pocket door entry Cut to length for easy installation Can be stained or painted Item Description Units List 1-2X6WALL 2 X 6 Wall Pocket EA Used with 2 x 6 wall application 2 x 6 Wall Item Description Units List 1-5/8DRYWALL 5/8 Drywall for Pockets EA Used with 5/8" drywall application 5/8" Drywall Page PF125

27 Item Description Units List 1-FR13/4 1 3/4" Door pening EA on Pockets To provide opening for 1 3/4 door Warning: Do to constricting wall widths of 3 1/2" stud, doors may warp beyond pocket opening. 2 x 6 studs guarantes ample room for 1 3/4" doors. Item Description Units List 1-70EXTENTIN #1752 7/0 Extent ion Kit EA (for Built-Up Pockets) Used to add extra height to the standard 6/8 height frames Item Description Units List E 1-80EXTENTIN #1753 8/0 Extention Kit EA T (for Built-Up Pockets) Used for adding extra height to the standard D 6/8 height frames KIT # Extent ion Kit EA R (for 2000 K.D. Pockets) Used to add extra height to the standard A 6/8 height frames C C Item Description Units List E KIT # Extent ion Kit EA S (for 2000 K.D. Pockets) S Used to add extra height to the standard 6/8 height frames R I E Item Description Units List S KIT # Extention Kit EA (for 2000 K.D. Pockets) Used to add extra height to the standard 6/8 height frames P C K Baskets Description Size Units List BSKT 2'0" X 6'8" Basket EA BSKT 2'2" X 6'8" Basket EA BSKT 2'4" X 6'8" Basket EA BSKT 2'6" X 6'8" Basket EA BSKT 2'8" X 6'8" Basket EA BSKT 3'0" X 6'8" Basket EA BSKT 4'0" X 6'8" Basket EA Pre-Assembled basket to accept a slab door For 1 3/8" Doors Page PF126

28 Item Description Size Units List HEAD 2'0" Header EA HEAD 2'2" Header EA HEAD 2'4" Header EA HEAD 2'6" Header EA HEAD 2'8" Header EA HEAD 3'0" Header EA HEAD 4'0" Header EA KDHEAD K/D Header EA P Pre Assembled Header unit with cut marks on header make for easy sizing C K Item Description Unit List E 1-751CNNECTR #751 Mullion Connector EA T Joins 2 pocket door frames to make one large doorway D Can be used for Built Ups & K.D. Units R Item Description Size Units List Track H TRACK 2'0" Track 47 ¼" EA A TRACK 2'2" Track 52 ¼" EA R TRACK 2'4" Track 54 ¼" EA D TRACK 2'6" Track 58 ¼" EA W TRACK 2'8" Track 62 ¼" EA A TRACK 3'0" Track 70 ¼" EA R TRACK 4'0" Track 96 EA E TRACK 5'0" Track 120 EA TRACK 6'0" Track 144 EA KDTRACK K/D Track 69" EA Item Description Units List HDW 1750 Hardware #150lbs EA Four large wheels easy snap-in installation Use with 150 lbs bipass panels Pocket Hardware for single 1-1/8" to 1 3/4" door up to 150 lbs Set Includes: 1-Wrench, 2-Splitfloor guides, 2-Hangers Item Description Units List BALLBEAR 1750 Hardware #250 lbs EA Ball Bearing Four large wheels, easy snap-in installation Use with 250 lbs bipass panels Pocket Hardware for single 1-1/8" to 1 3/4" door up to 250 lbs Set Includes: 1-Wrench, 2-Splitfloor guides, 2-Ball Bearing Hangers Page PF127

29 Item Description Units List 100HDW 100 Hardware Set Johnson EA # wheel Pocket Hardware for single 1-1/8" to 1 3/4" door up to 125 lbs Set Includes: 1-Wrench, 2-Guides, 2-Hangers Item Description Units List 100HDWBB 100 Ball Bearing Hardware Set Johnson EA wheel Pocket Hardware for single 1-1/8" to 1 3/4" door up to 250 lbs Set Includes: 1-Wrench, 2-Guides, 2-Ball Bearing Hangers Item Description Units List E 1-BUMPER Bumper for Pocket EA T Plastic Finish D For Pocket Doors R Item Description Units List 1 WRENCH Adjustable Wrench EA H Used to adjust hardware A R D W Item Description Set List A 1-FLRBRACKET Floor brackets 1 set K.D. EA R 2 brackets, nails bumper screws t assemble kd pocket unit E P C K Item Description Units List 1-68KDSTIFFINE KD 6/8 Stiffener EA Steel Stiffener w/wood for K.D. Pocket 83 1/2" Length Item Description Units List 1-BU68STIFFINE Built Up 6/8 Stiffener EA Steel Stiffener for 6/8 built up Pocket 82 1/8" Length Page PF128

30 Item Description Units List 1-BU70STIFFENE Built Up 7/0 Stiffener EA Steel Stiffener for 7/0 built up Pocket 86 1/8" Length Item Description Units List 1-BU80STIFFENE Built Up 8/0 Stiffener EA Steel Stiffener for 8/0 built up Pocket 98 1/8" Length P C K Item Description Units List E 1-13/4FLRGUI #111 - Floor Guide 1 ¾) EA T adjusts to center door in pocket Adjustable D Guides bottom of door into pocket R Item Description Units List H 1-13/8FLRGUI #107 - Floor Guide 1 3/8) EA A Adjusts to center door of pocket R Guides Bottom of door into pocket D W A R E Item Description Units List 1-BRACKET Universal Bracket EA for K.D. End Brackets for K.D. Headers aka - wall bracket Item Description Units List 1-BUFLRPLATE Built-Up Floor Plate EA Floor plate for built up pocket aka spacer/sill plate Page PF129

31 Item Description Units List 1-SPLITFLRGU #113 Split Floor Guide EA Adjusts to center door in pocket Adjustable 1 Pair of split floor guides Item Description Units List P 1-MULLINSTP #115 Center Stop EA C K E T D Item Description Finish Units List Pocket Latches - Privacy R 263-PCKETP26D Pocket Door Latch Privacy US26D EA PCKETPUS3 Pocket Door Latch Privacy US3 EA H Privacy Sliding Door Lock A R D W A R E Item Description Finish Units List Pocket Latches - Pulls 263-PCKETL26D Pocket Pull US26D EA PCKETLUS3 Pocket Pull US3 EA Passage Sliding Door Lock Page PF130

32 30 lbs Bifold Track & Hardware Set for 1 1/8" to 1 3/8" panels Light Duty - Complete Set 2 Door System 4 Door System Item Description Size Units Panel List Price 26-20BIFSET 2'0" Bifold Track & Hdw Set 24 EA BIFSET 2'6" Bifold Track & Hdw Set 30 EA BIFSET 3'0" Bifold Track & Hdw Set 36 EA BIFSET 4'0" Bifold Track & Hdw Set 48 EA BIFSET 5'0" Bifold Track & Hdw Set 60 EA BIFSET 6'0" Bifold Track & Hdw Set 72 EA BIFSET 8'0" Bifold Track & Hdw Set 96 EA Complete Bifold Track & Hardware Set ne set consists of 1 Track, 2 Snuggers, 1 Top Pivot, 1 Guide Wheel, 1 Bottom Pivot, 1- Knob, 1 Jamb Bracket B I Item Description Size Units List Price F Track 30lbs 26-20BIFTR 2'0" Bifold Track 30 lbs 24 EA L 26-26BIFTR 2'6" Bifold Track 30 lbs 30 EA D 26-30BIFTR 3'0" Bifold Track 30 lbs 36 EA BIFTR 4'0" Bifold Track 30 lbs 48 EA D 26-50BIFTR 5'0" Bifold Track 30 lbs 60 EA BIFTR 6'0" Bifold Track 30 lbs 72 EA BIFTR 8'0" Bifold Track 30 lbs 96 EA R Item Description Units Panel List Price H Bifold Hardware Standard 30 Lbs A 26-BIFHDW 2 Panel Bifold Hardware EA 2p Set 5.91 R Set includes: 1-Track, 1-Roller,1-top Pivot, 1 Pivot Lock,1-Bottom Pivot,1-Floor Pivot Bracket, D 1-Non-Mortise Lift off Hinge, 1 4 Door Aligner, 1 Knob, 1-adjustment Wrench W Note: For a 4 panel door you need to order two packages of bifold hardware A R Item Description Units List Price E 26-TPPIVT Top Pivot 30lb Bifold Hdw EA 1.02 Used with top pivot brackets on door panel Item Description Units List Price 26-BTMPIVT Bottom Pivot 30lb Bifold Hdw EA 0.77 Provides vertical adjustment of doors Slips into jamb bracket at floor level and can be moved horizontally Item Description Units List Price 26-GUIDEWHE Guide Wheel 30lb Bifold EA 1.19 Provides door movement on track Item Description Units List Price 26-KNBPLAS Plastic Knob 30 lb Bifold EA 0.60 Use on two or four door panels pen and close doors easily Page PF131

33 Item Description Units List Price 26-SNUGGER Snugger 30 lb Bifold EA 2p Set 0.64 Holds doors snub 4p Set 0.81 Item Description Units List Price 26-JAMBBRAC Jamb Bracket 30 lb Bifold EA 1.06 Easy horizontal adjustment B Item Description Units List Price I F 26-ALLIGNER Alligner 30 lb Bifold EA 0.98 For use in four door installations L Use on all door sizes D Brings leading dor edges into alignment D Item Description Units List Price 26-BIFHINGE Non-Mortise Hinge EA 1.87 For surface mounting R No Mortising required H A 75 lbs Bifold Track & Hardware Set for 1 1/8" to 1 3/8" panels Heavy Duty - Complete Set R 2 Door System 4 Door System D Item Description Size Units Panel List Price W A BIFSET 3'0" Bifold Track & Hdw Set 75lbs 36 EA R BIFSET 4'0" Bifold Track & Hdw Set 75lbs 48 EA E BIFSET 5'0" Bifold Track & Hdw Set 75lbs 60 EA BIFSET 6'0" Bifold Track & Hdw Set 75lbs 72 EA BIFSET 8'0" Bifold Track & Hdw Set 75lbs 96 EA Heavy duty track and hardware for doors weighing over 75 lbs each panel ne set consists of: 1 Track, 3 Non-Mortise Hinges, 2 Bottom Pivots, 2 Knobs, 1 Hardware, 1 Bottom Pivot Bracket, 1 Wrench, 1 Installation Hardware, 2 Door Aligners, 1 Top Pivot Item Description Size units List Price Track 75 lbs BIFTR 3'0" Bifold Track 75 lbs. 36" EA BIFTR 4'0" Bifold Track 75 lbs. 48 EA BIFTR 5'0" Bifold Track 75 lbs. 60 EA BIFTR 6'0" Bifold Track 75 lbs. 72 EA BIFTR 8'0" Bifold Track 75 lbs. 96 EA Item Description Units Panel List Price Bifold Hardware Standard 75 Lbs 2601-HDWBIF2P #291 Hardware 75 Lbs Complete Set EA 2p Set HDWBIF4P #291 Hardware 75 Lbs Complete Set EA 4p Set Commercial Based Hardware Page PF132

34 Item Description Units List Price 2601-HDW #291 Hardware 75 Lbs Single Piece EA 6.63 Item Description Units List Price 2601-TPPIVT Top Pivot 75Lbs EA Top pivot bracket B I Item Description Units List Price F 2601-STP Track Stop 75 Lbs EA 1.62 Track stop L D Item Description Units List Price D 2601-BTMPIVT Bottom Pivot Bracket 75 Lbs EA 6.12 Provides vertical adjustment on doors R H Item Description Units List Price A R 2601-NNHING Non-Mortise Hinge 75 lbs EA 4.38 D For surface mounting W A R Item Description Units List Price E 2601-ALLIGNER Alligner 75lbs EA 0.94 Brings leading door into alignment Item Description Units List Price 2601-WRENCH Wrench 75lbs EA 0.47 Used for adjustments Item Description Units List Price 2601-KNB Plastic Knob 75lbs EA 0.55 pen and close doors easily Item Description Units List Price 2601-INSTHDW Installation Hardware 75lb EA 3.40 Packaged hardware Page PF133

35 Item Description Units Panel List Price 150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set 2 Door System BIPAS2D 4/0 Bipass Track & Hdw 150 lbs 2dr 48 pening EA BIPAS2D 5/0 Bipass Track & Hdw 150 lbs 2dr 60 pening EA BIPAS2D 6/0 Bipass Track & Hdw 150 lbs 2dr 72 pening EA BIPAS2D 8/0 Bipass Track & Hdw 150lbs 2dr 96 pening EA Set Includes: 2-Track, 2-Hardware, 2-Spacers, 1-Floor Guide, 1 Wrench B Item Description Units Panel List Price I 150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set P 3 Door System A S BIPAS3D 4/0 Bipass Track & Hdw 150 lbs 3dr 48 pening EA S BIPAS3D 5/0 Bipass Track & Hdw 150 lbs 3dr 60 pening EA BIPAS3D 6/0 Bipass Track & Hdw 150 lbs 3dr 72 pening EA D BIPAS3D 8/0 Bipass Track & Hdw 150lbs 3dr 96 pening EA Set Includes: 2-Track, 3-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench R Item Description Units Panel List Price H 150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set A 4 Door System R BIPAS4D 4/0 Bipass Track & Hdw 150 lbs 4dr 48 pening EA D BIPAS4D 5/0 Bipass Track & Hdw 150 lbs 4dr 60 pening EA W BIPAS4D 6/0 Bipass Track & Hdw 150 lbs 4dr 72 pening EA A BIPAS4D 8/0 Bipass Track & Hdw 150lbs 4dr 96 pening EA 4 R Set Includes: 2-Track, 4-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench E Item Description Units Panel List Price 250 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set 2 Door System BIPAS2D 4/0 Bipass Track & Hdw 250 lbs 2dr 48 pening EA BIPAS2D 5/0 Bipass Track & Hdw 250 lbs 2dr 60 pening EA BIPAS2D 6/0 Bipass Track & Hdw 250 lbs 2dr 72 pening EA BIPAS2D 8/0 Bipass Track & Hdw 250lbs 2dr 96 pening EA Set Includes: 2-Track, 2-Hardware, 2-Spacers, 1-Floor Guide, 1 Wrench Item Description Units Panel List Price 250 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set 3 Door System BIPAS3D 4/0 Bipass Track & Hdw 250 lbs 3dr 48 pening EA BIPAS3D 5/0 Bipass Track & Hdw 250 lbs 3dr 60 pening EA BIPAS3D 6/0 Bipass Track & Hdw 250 lbs 3dr 72 pening EA BIPAS3D 8/0 Bipass Track & Hdw 250lbs 3dr 96 pening EA Set Includes: 2-Track, 3-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench Page PF134

36 Item Description Units Panel List Price 250 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set 4 Door System BIPAS4D 4/0 Bipass Track & Hdw 250 lbs 4dr 48 pening EA BIPAS4D 5/0 Bipass Track & Hdw 250 lbs 4dr 60 pening EA BIPAS4D 6/0 Bipass Track & Hdw 250 lbs 4dr 72 pening EA BIPAS4D 8/0 Bipass Track & Hdw 250lbs 4dr 96 pening EA Set Includes: 2-Track, 4-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench Item Description Units List Price B Track 150 & 250 Lbs I TRACK 2'0" Track 48 48" EA 9.72 P TRACK 2'6" Track 60 60" EA A TRACK 3'0 Track 72 " 72" EA S TRACK 4'0" Track 96 96" EA S D Item Description Units List Price HDW #1750 Hardware Set EA R Four large ball bearing wheels, easy snap-in installation feature For use with panels weighing up to 150 lbs. H A R Item Description Units List Price D W BALLBEAR #1750 Ball Bearing Hardware Set EA A Four large ball bearing wheels, easy snap-in installation feature R For use with panels weighing up to 250 lbs. E Item Description Units List Price 1-WRENCH Adjusting Wrench EA 0.47 Item Description Units List Price 29-BIPASSPACE Bipass Track Spacer EA 7.95 Provides correct spacing between tracks for 1 ¾ doors Simplifies installation of 2 or more tracks Item Description Units List Price 29-BIPASSFLRGU Bipass Floor Guide Adjustable EA 6.97 Adjustable for 1 3/8 to 1 ¾ thick by passing doors Page PF135

37 Item Description Units Panel List Price 150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set 2 Door System BIPAS2D 4/0 Bipass Track & Hdw 150 lbs 2dr 48 pening EA BIPAS2D 5/0 Bipass Track & Hdw 150 lbs 2dr 60 pening EA BIPAS2D 6/0 Bipass Track & Hdw 150 lbs 2dr 72 pening EA BIPAS2D 8/0 Bipass Track & Hdw 150lbs 2dr 96 pening EA Set Includes: 2-Track, 2-Hardware, 2-Spacers, 1-Floor Guide, 1 Wrench B Item Description Units Panel List Price I 150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set P 3 Door System A S BIPAS3D 4/0 Bipass Track & Hdw 150 lbs 3dr 48 pening EA S BIPAS3D 5/0 Bipass Track & Hdw 150 lbs 3dr 60 pening EA BIPAS3D 6/0 Bipass Track & Hdw 150 lbs 3dr 72 pening EA D BIPAS3D 8/0 Bipass Track & Hdw 150lbs 3dr 96 pening EA Set Includes: 2-Track, 3-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench R Item Description Units Panel List Price H 150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set A 4 Door System R BIPAS4D 4/0 Bipass Track & Hdw 150 lbs 4dr 48 pening EA D BIPAS4D 5/0 Bipass Track & Hdw 150 lbs 4dr 60 pening EA W BIPAS4D 6/0 Bipass Track & Hdw 150 lbs 4dr 72 pening EA A BIPAS4D 8/0 Bipass Track & Hdw 150lbs 4dr 96 pening EA 4 R Set Includes: 2-Track, 4-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench E Item Description Units Panel List Price 250 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set 2 Door System BIPAS2D 4/0 Bipass Track & Hdw 250 lbs 2dr 48 pening EA BIPAS2D 5/0 Bipass Track & Hdw 250 lbs 2dr 60 pening EA BIPAS2D 6/0 Bipass Track & Hdw 250 lbs 2dr 72 pening EA BIPAS2D 8/0 Bipass Track & Hdw 250lbs 2dr 96 pening EA Set Includes: 2-Track, 2-Hardware, 2-Spacers, 1-Floor Guide, 1 Wrench Item Description Units Panel List Price 250 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set 3 Door System BIPAS3D 4/0 Bipass Track & Hdw 250 lbs 3dr 48 pening EA BIPAS3D 5/0 Bipass Track & Hdw 250 lbs 3dr 60 pening EA BIPAS3D 6/0 Bipass Track & Hdw 250 lbs 3dr 72 pening EA BIPAS3D 8/0 Bipass Track & Hdw 250lbs 3dr 96 pening EA Set Includes: 2-Track, 3-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench Page PF136