AUTODESK INVENTOR Trial Projects
|
|
|
- Percival Price
- 6 years ago
- Views:
Transcription
1 AUTODESK INVENTOR Trial Projects Drawing Creation Create detailed drawings of a collar flange
2 PART 1: CREATING DRAWING VIEWS page: Start by clicking the Projects icon in the ribbon. Navigate to where you saved the project files and select Collar-Flange- Assembly.ipj. Then open Collar-Flange-Assembly.iam. 4. Select the Flanged-Collar component in the model window and right click to bring up the marking menu. Select open. With Flanged-Collar.ipt open, select File and choose New from the ribbon menu. In the dialog, select the Metric folder and choose ANSI (mm).dwg as the drawing template. In the model browser on the left of the screen, right click Sheet:1 and choose Edit Sheet....
3 PART 1: CREATING DRAWING VIEWS page: Change the sheet size to C and select OK. 8. In the model window, right click to open the marking menu and choose Base View.... Change the scale to 2:1 and ensure the style is set to Hidden Line as shown. Drag the view towards the left side of the drawing and use the arrows on each side of the ViewCube to orient the model as shown (down arrow, then the right arrow) and click OK. With the base view selected, start Projected View from the marking menu. Move your cursor and click in each direction to place the views and then right click and select Create.
4 PART 1: CREATING DRAWING VIEWS page: With the base view selected, open Section View from the marking menu. Draw a vertical line through the middle of the part as shown. Right click and select Continue. 12. Slide your cursor to the right and click to place the view. Break the forced alignment by right clicking on the view, selecting Alignment and choosing Break. After breaking the alignment, move the view to the upper right quadrant of the drawing as shown.
5 PART 1: CREATING DRAWING VIEWS page: To remove the display of the selection line through the part in the Base view, right click the line and uncheck Show Entire Line. 16. To create a detail view, right click inside the Section A-A view and select Detail View from the marking menu. Draw out the circle as shown to specify the area of the detail view. Click to set the circle diameter, and then move your cursor to the location on the sheet where you want the detail view placed.
6 PART 2: DRAWING ANNOTATIONS page: Using the same drawing created in Part 1, select Centerline Bisector from the Annotate tab in the ribbon. 4. Select the edges as highlighted (green and red) to create a centerline in Section A-A. Repeat to add centerlines in the Base and Right views of the part. Start the Center Mark command from the Annotate tab in the ribbon. Select the holes in the Base, Top, and Right views as highlighted in red in the image above.
7 PART 2: DRAWING ANNOTATIONS page: Start the Centerline command from the Annotate tab in the ribbon. 8. In the top view, select each of the four holes highlighted in green above. Select the hole you picked first a second time to complete the centerline. Right click and select Create. In the Base, Right, and Section A-A views, adjust the centerline length beyond the part by clicking the line and moving the green handle. In Section A-A, right click to open the marking menu and select General Dimension. Choose the line as shown and click where you want to place the dimension. Click OK in the dialog.
8 PART 2: DRAWING ANNOTATIONS page: Repeat the process to add the dimensions shown. (Move the Section A-A title down if needed). Select the two points shown to create an additional dimension. Place below the 30mm diameter dimension In the dialog box, add a Diameter symbol at the beginning of the text field and select OK. Right click in the model window and select OK to finish the dimension command. On the Annotate tab in the ribbon, select the drop down arrow next to Ordinate and start the Ordinate Set command.
9 PART 2: DRAWING ANNOTATIONS page: Pick the corner as shown and then right click to select Continue. Place the.00 dimension to the left as shown. Select the points needed to add the additional dimensions as shown. Right click in the window and select Create Looking at the Detail B view, right click and select General Dimension. Pick the corners of the slot to create the dimension shown. In the dialog box, open the Precision and Tolerance tab. Select Deviation as the method and enter 0.05 as the upper limit.
10 PART 2: DRAWING ANNOTATIONS page: Repeat for the height dimension, this time using 0.02 as the upper limit. 20. Looking at the Top view, right click and choose General Dimension. Detail the drawing as shown above. Note: Angular dimensions can be created by clicking the centerlines of the holes. In the Annotate tab inside the ribbon, select Hole and Thread. Select the hole in the top left of the part and place the dimension.
11 PART 2: DRAWING ANNOTATIONS page: Inside the Base view, right click select Retrieve Dimensions from the marking menu. This brings up all dimensions that were used to define the 3D model. 24. Window select the area shown to bring up dimensions associated with those features. In the dialog box, click the arrow next to Select Dimensions. Choose the 6mm diameter dimension and click OK. Move the dimension to the right side of the view. Right click on the 6mm diameter dimension and choose Edit Model Dimension from the marking menu. With this, you can change 3D model parameters from within the drawing view.
12 PART 2: DRAWING ANNOTATIONS page: Change the Hole Diameter to 7mm and click OK. The drawing will update immediately and the change will be carried over to the 3D model as well. For additional practice, you can fully detail the Base and Right views as shown above using the techniques previously used. Save and close the drawing when complete.
13 PART 3: ASSEMBLY DRAWING page: Reopen Collar-Flange-Assembly.iam. Create a new drawing by selecting New from the ribbon menu and select the same drawing template as before, ANSI (mm).dwg. 4. In the model browser, right click on Sheet:1 and choose Edit Sheet.... Change the sheet size to C. Open Base View from the marking menu. Set the style to Hidden Line and Scale to 2:1. Click to place the view in the top left corner and then click below to create the side view. Right click inside the Top view and select Section View. Draw the line as shown above to define the section, right click and select continue.
14 PART 3: ASSEMBLY DRAWING page: Place the view to the right. Right click inside Section A-A and select Automated Centerlines. Select Cylindrical Features in the dialog and check both boxes in Projection. Click OK. 8. Repeat the Automated Centerlines operation with the same settings in both the Top and Front views of the drawing. Start the General Dimension command from the marking menu and add the dimensions as shown in the Front view. Right click in the model window and select Base View again from the marking menu. In the dialog, click the folder icon to open a view from an existing file.
15 PART 3: ASSEMBLY DRAWING page: Select Collar-Flange-Assembly.ipn and click Open. 12. Click the corner of the ViewCube as shown to change to an isometric view of the exploded assembly. Move the view to the top right corner of the sheet. In the Style section of the dialog, make sure both Hidden Lines Removed and Shaded are selected and select OK. In the Annotate tab in the ribbon, select Auto Balloon.
16 PART 3: ASSEMBLY DRAWING page: Click on the exploded view to Select View Set and then window select all the parts for Add or Remove Components. 16. Choose the Select Placement button in the dialog and click to place the balloons below the view. Click OK in the dialog to complete the command. Window select the balloons and then right click to bring up the marking menu. Go to the Align pop out and select To Edge. Select the edge of the flange highlighted in red as shown and then drag the balloons away from the part to their final placement to complete the drawing.
17 Autodesk, Autodesk Inventor, and the Autodesk logo are registered trademarks or trademarks of Autodesk, Inc., and/or its subsidiaries and/or affiliates in the USA and/or other countries. All other brand names, product names, or trademarks belong to their respective holders. Autodesk reserves the right to alter product offerings and specifications at any time without notice, and is not responsible for typographical or graphical errors that may appear in this document Autodesk, Inc. All rights reserved.
Quick Start for Autodesk Inventor
Quick Start for Autodesk Inventor Autodesk Inventor Professional is a 3D mechanical design tool with powerful solid modeling capabilities and an intuitive interface. In this lesson, you use a typical workflow
AutoDesk Inventor: Creating Working Drawings
AutoDesk Inventor: Creating Working Drawings Inventor allows you to quickly and easily make quality working drawings from your 3D models. This tutorial will walk you through the steps in creating a working
Introduction to Autodesk Inventor for F1 in Schools (Australian Version)
Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital
ME Week 2 Project 2 Flange Manifold Part
1 Project 2 - Flange Manifold Part 1.1 Instructions This project focuses on additional sketching methods and sketching commands. Revolve and Work features are also introduced. The part being modeled is
Creo: Hole, Fillet, and Round Layout/Dimension Tutorial. By: Matthew Jourden Brighton High School
Creo: Hole, Fillet, and Round Layout/Dimension Tutorial Layout of a Part with Holes 1. Open a blank drawing with your border and title block By: Matthew Jourden Brighton High School 2. Place the front,
User Guide V10 SP1 Addendum
Alibre Design User Guide V10 SP1 Addendum Copyrights Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement or
Toothbrush Holder. A drawing of the sheet metal part will also be created.
Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson; Sketch (Line, Centerline, Circle, Add Relations, Smart Dimension,), Extrude Boss/Base, and Edit
8 Working Drawings in AutoCAD
8 Working Drawings in AutoCAD Most engineering designs consist of more than a single part. Usually there are a several or many parts that must fit and work together. When we are creating the drawings of
Solid Part Four A Bracket Made by Mirroring
C h a p t e r 5 Solid Part Four A Bracket Made by Mirroring This chapter will cover the following to World Class standards: Sketch of a Solid Problem Draw a Series of Lines Finish the 2D Sketch Extrude
Engineering Technology
Engineering Technology Introduction to Parametric Modelling Engineering Technology 1 See Saw Exercise Part 1 Base Commands used New Part This lesson includes Sketching, Extruded Boss/Base, Hole Wizard,
Certified SOLIDWORKS Professional Advanced Preparation Materials
Includes Preparation for Five Advanced Certification Exams Certified SOLIDWORKS Professional Advanced Preparation Materials Sheet Metal, Weldments, Surfacing, Mold Tools and Drawing Tools SOLIDWORKS 2016
Introduction to Parametric Modeling AEROPLANE. Design & Communication Graphics 1
AEROPLANE Design & Communication Graphics 1 Object Analysis sheet Design & Communication Graphics 2 Aeroplane Assembly The part files for this assembly are saved in the folder titled Aeroplane. Open an
Creating Transparency for Glass in an Illustration with. SketchBook Designer
Autodesk Design Suite 2012 Autodesk SketchBook Designer 2012 Tip Guides Creating Transparency for Glass in an Illustration with SketchBook Designer In this section you will learn the following: How to
Beginner s Guide to SolidWorks Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS
Beginner s Guide to SolidWorks 2008 Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Part Modeling
To start a new drawing Select File New then from the dialog box, which appears select Normal.dft followed by OK.
Draft Tutorial This tutorial provides step-by-step instructions for the detailing of a drawing of the anchor block shown opposite. As you create this drawing, you will use the following drafting techniques:
NX9 Manual Drafting. BINDE Training
Extract of 82 pages NX9 Manual Drafting Drafting K Table of contents 1 K - Drafting K1 Start Drafting K1-1 Create Drawing K1-3 Drawing Navigator K1-4 Drafting Ribbon Bar K2 Drawing Sheet K3 Views K3-1
Appendix R5 6. Engineering Drafting. Broken View
Updating Using Autodesk Inventor to Release 5 Appendix R5 6 Engineering Drafting Chapter 6 delineates the concepts of engineering drafting. You output orthographic views from solid parts and orthographic
Getting Started. Chapter. Objectives
Chapter 1 Getting Started Autodesk Inventor has a context-sensitive user interface that provides you with the tools relevant to the tasks being performed. A comprehensive online help and tutorial system
Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder
Inventor (10) Module 1E: 1E- 1 Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder In this Module, we will explore the topic
Creating a Sketchbook in Sketchbook Designer based on a photo and Reusing it in AutoCAD
Autodesk Design Suite 2012 Autodesk SketchBook Designer 2012 Tip Guides Creating a Sketchbook in Sketchbook Designer based on a photo and Reusing it in AutoCAD In this section you will learn the following:
Revit Structure 2012 Basics:
SUPPLEMENTAL FILES ON CD Revit Structure 2012 Basics: Framing and Documentation Elise Moss autodesk authorized publisher SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Structural
Drawing a Plan of a Paper Airplane. Open a Plan of a Paper Airplane
Inventor 2014 Paper Airplane Drawing a Plan of a Paper Airplane In this activity, you ll create a 2D layout of a paper airplane. Please follow these directions carefully. When you have a question, reread
DRAFT Solid Edge ST4 Update Training Draft
DRAFT Solid Edge ST4 Update Training Draft Presented by: Steve Webb Topics Parts List Table Titles Column Headers Headers Merging Header Rotate Cell Aspect Ratio Cell Formatting Overriding Disabled Cells
Chapter 2. Drawing Sketches for Solid Models. Learning Objectives
Chapter 2 Drawing Sketches for Solid Models Learning Objectives After completing this chapter, you will be able to: Start a new template file to draw sketches. Set up the sketching environment. Use various
AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.
AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and
When you complete this assignment you will:
Objjectiives When you complete this assignment you will: 1. sketch and dimension circles and arcs. 2. cut holes in the model using the cut feature of the extrusion command. 3. create Arcs using the trim
Drawing and Detailing with SolidWorks 2014
r n fo io n at io c at tifi ar er ep c pr WT es D R u d Pcl In C S W e th W E N Drawing and Detailing with SolidWorks 2014 Referencing the ASME Y14 Engineering Drawing and Related Documentation Practices
GEN20604 Intelligent AutoCAD Model Documentation Made Easy
GEN20604 Intelligent AutoCAD Model Documentation Made Easy David Cohn 4D Technologies Learning Objectives Learn how to create base views and projected views from 3D models Learn how to create and control
What s New in Autodesk Inventor 2018
What s New in Autodesk Inventor 2018 Welcome & Agenda Introduction to Inventor 2018 Professional- Grade Design Enhancements Expanded I nteroperability The I nventor Experience Autodesk Inventor 2018 I
SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI
SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered
Chapter 5 Sectional Views
Chapter 5 Sectional Views There are a number of different types of sectional views that can be drawn. A few of the more common ones are: full sections, half sections, broken sections, rotated or revolved
Activity 7.1 More Dimensioning
Activity 7.1 More Dimensioning Introduction The basic standard dimensioning method established by the American National Standards Institute and the American Society of Mechanical Engineers (ANSI or ASME)
Getting Started. Before You Begin, make sure you customized the following settings:
Getting Started Getting Started Before getting into the detailed instructions for using Generative Drafting, the following tutorial aims at giving you a feel of what you can do with the product. It provides
Assignment 5 CAD Mechanical Part 1
Assignment 5 CAD Mechanical Part 1 Objectives In this assignment you will apply polyline, offset, copy, move, and rotated dimension commands, as well as skills learned in earlier assignments. Getting Started
Lesson 4 Holes and Rounds
Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information
Making an Architectural Drawing Template
C h a p t e r 8 Addendum: Architectural Making an Architectural Drawing Template In this chapter, you will learn the following to World Class standards:! Starting from Scratch for the Last time! Creating
Dimension Properties. Student Web Site
Dimension Properties All sketch dimensions added to a sketch contain specific individual dimension properties. Most dimension properties are predefined by default or are specified in the Modeling Dimension
Creo Revolve Tutorial
Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate
Alibre Design Exercise Manual Introduction to Sheet Metal Design
Alibre Design Exercise Manual Introduction to Sheet Metal Design Copyrights Information in this document is subject to change without notice. The software described in this documents is furnished under
Below are the desired outcomes and usage competencies based on the completion of Project 4.
Engineering Design with SolidWorks Project 4 Below are the desired outcomes and usage competencies based on the completion of Project 4. Project Desired Outcomes: An understanding of the customer s requirements
Engineering Design with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P.
Engineering Design with SolidWorks 2003 A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard SDC PUBLICATIONS www.schroff.com www.schroff-europe.com
When you complete this assignment you will:
Objjectiives When you complete this assignment you will: 1. sketch and create models using new work planes and the loft command. 2. sketch and create models using the revolve command. 3. sketch and dimension
Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece
1 Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece In this Module, we will explore the method of adding dovetail seams to curved edges such as the circumferential edge of a
Assemble This! [Part 1]
![Assemble This! [Part 1]](/thumbs/74/69963588.jpg "Assemble This! [Part 1]")
11/30/2006-3:00 pm - 4:30 pm Room:Marcello - 4401 (MSD Campus) Assemble This! [Part 1] Alan Kalameja - Trident Technical College and Kevin Robinson (Assistant); Patrik Chartrand (Assistant) MA34-1L This
Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated)
Inventor (5) Module 2: 2-1 Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated) In this tutorial, we will learn how to build a 3D model
Assembly Receiver/Hitch/Ball/Pin to use for CAD LAB 5A and 5B:
MECH 130 CAD LAB 5 SPRING 2017 due Friday, April 21, 2016 at 4:30 PM All of LAB 5 s hardcopies will be working drawing layouts. Do not print out from the part file. We will be using the ME130DRAW drawing
Shaft Hanger - SolidWorks
ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Shaft Hanger - SolidWorks BY: DR. HERLI SURJANHATA ASSIGNMENT Submit TWO isometric views of the Shaft Hanger with your report, 1. Shaded view of the trimetric
Revit Structure 2014 Basics
Revit Structure 2014 Basics Framing and Documentation Elise Moss Authorized Author SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit
An Introduction to Dimensioning Dimension Elements-
An Introduction to Dimensioning A precise drawing plotted to scale often does not convey enough information for builders to construct your design. Usually you add annotation showing object measurements
On completion of this exercise you will have:
Prerequisite Knowledge To complete this exercise you will need; to be familiar with the SolidWorks interface and the key commands. basic file management skills the ability to rotate views and select faces
AutoCAD Inventor - Solid Modeling, Stress and Dynamic Analysis
PDHonline Course G280 (15 PDH) AutoCAD Inventor - Solid Modeling, Stress and Dynamic Analysis Instructor: John R. Andrew, P.E. 2012 PDH Online PDH Center 5272 Meadow Estates Drive Fairfax, VA 22030-6658
Making Standard Note Blocks and Placing the Bracket in a Drawing Border
C h a p t e r 12 Making Standard Note Blocks and Placing the Bracket in a Drawing Border In this chapter, you will learn the following to World Class standards: Making standard mechanical notes Using the
An Introduction to Autodesk Inventor 2011 and AutoCAD Randy H. Shih SDC PUBLICATIONS. Schroff Development Corporation
An Introduction to Autodesk Inventor 2011 and AutoCAD 2011 Randy H. Shih SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation An Introduction to Autodesk Inventor 2011 and AutoCAD 2011
Modeling an Airframe Tutorial
EAA SOLIDWORKS University p 1/11 Difficulty: Intermediate Time: 1 hour As an Intermediate Tutorial, it is assumed that you have completed the Quick Start Tutorial and know how to sketch in 2D and 3D. If
Drawing and Detailing
Drawing and Detailing with SolidWorks 2005 By David C. Planchard and Marie P. Planchard Referencing the ASME Y14 Engineering Drawing and Related Documentation Practices SDC PUBLICATIONS Schroff Development
Assignment 12 CAD Mechanical Part 2
Assignment 12 CAD Mechanical Part 2 Objectives In this assignment you will learn to apply the hidden lines, isometric snap, and ellipses commands along with commands previously learned.. General Hidden
AutoCAD Architecture 2018 Fundamentals
Elise Moss Autodesk AutoCAD Architecture 2018 Fundamentals SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites
Making an Architectural Drawing Template
C h a p t e r 8 Addendum: Architectural Making an Architectural Drawing Template In this chapter, you will learn the following to World Class standards: 1. Starting from Scratch 2. Creating New Layers
1. Respect yourself, your associates, and your school.
Classroom rules Tuesday, August 30, 2011 2:16 PM Rules 1. Respect yourself, your associates, and your school. 2. Enter the room, be seated, and check the board before the bell rings. 3. 4. 5. 6. 7. Eyes
Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge
Inventor (10) Module 1G: 1G- 1 Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge In Module 1A, we have explored
Lesson 6 2D Sketch Panel Tools
Lesson 6 2D Sketch Panel Tools Inventor s Sketch Tool Bar contains tools for creating the basic geometry to create features and parts. On the surface, the Geometry tools look fairly standard: line, circle,
ENGINEERING GRAPHICS ESSENTIALS
ENGINEERING GRAPHICS ESSENTIALS with AutoCAD 2012 Instruction Introduction to AutoCAD Engineering Graphics Principles Hand Sketching Text and Independent Learning CD Independent Learning CD: A Comprehensive
< Then click on this icon on the vertical tool bar that pops up on the left side.
Pipe Cavity Tutorial Introduction The CADMAX Solid Master Tutorial is a great way to learn about the benefits of feature-based parametric solid modeling with CADMAX. We have assembled several typical parts
Full Section Tutorial Creating a Part
Full Section Tutorial Creating a Part 1. Create a block with the following measures a. Length=4.00 b. Depth=4.00 c. Height= 2.00 2. Place a Counterbore hole on the top view at the center of the block with
Create all plan and profile sheets in the current drawing. Create all plan and profile sheets in individual drawings.
NOTES Module 18 Roadway Plan Production In this module, you learn how to work with Roadway Plan Production tools in AutoCAD Civil 3D. The Plan Production tools are used to automate the generation of plan
Making a Drawing Template
C h a p t e r 8 Addendum: Metric Making a Drawing Template In this chapter, you will learn the following to World Class standards: 1. Starting from Scratch 2. Creating New Layers in an progecad Drawing
Technical What s New. AutoCAD. Mechanical 2011
AutoCAD Mechanical 2011 Welcome to AutoCAD Mechanical 2011 Contents Content Library...3 General Enhancements...3 Localization...3 Improved International Standards...3 Update Content Selectively...3 Part
Extracting Drawings - DEMO
Extracting Drawings - DEMO Although most demos are implemented with word documents, this demo employs slides so that more details can be shown to the students as the drawing is constructed. College of
Engineering & Computer Graphics Workbook Using SolidWorks 2014
Engineering & Computer Graphics Workbook Using SolidWorks 2014 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)
SolidWorks 2005 Tutorial. and MultiMedia CD. A Step-by-step Project Based Approach Utilizing 3D Solid Modeling
INSIDE: MultiMedia CD An audio/visual presentation of the tutorial projects SolidWorks 2005 Tutorial and MultiMedia CD A Step-by-step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard
Plant Design work flow Using Autodesk Plant Design Suite Ultimate. Carlos Caminos CAD Manager - Venture Engineering & Construction, Inc.
Plant Design work flow Using Autodesk Plant Design Suite Ultimate Carlos Caminos CAD Manager - Venture Engineering & Construction, Inc. Class Summary In this class, you will learn about a proven oil and
When you complete this assignment you will:
Objjectiives When you complete this assignment you will: 1. create an engineering drawing file using the management file menu. 2. dimension the engineering file using the drawing annotation menu. 3. produce
Chair. Bottom Rail. on the Command Manager. on the Weldments toolbar.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
Engineering & Computer Graphics Workbook Using SOLIDWORKS
Engineering & Computer Graphics Workbook Using SOLIDWORKS 2017 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)
Lesson 6: Drawing Basics
6 Lesson 6: Drawing Basics Goals of This Lesson Understand basic drawing concepts. Create detailed drawings of parts and assemblies:. Before Beginning This Lesson Create Tutor1 and Tutor2 parts and the
Getting started with. Getting started with VELOCITY SERIES.
Getting started with Getting started with SOLID EDGE EDGE ST4 ST4 VELOCITY SERIES www.siemens.com/velocity 1 Getting started with Solid Edge Publication Number MU29000-ENG-1040 Proprietary and Restricted
Name: Date Completed: Basic Inventor Skills I
Name: Date Completed: Basic Inventor Skills I 1. Sketch, dimension and extrude a basic shape i. Select New tab from toolbar. ii. Select Standard.ipt from dialogue box by double clicking on the icon. iii.
Up to Cruising Speed with Autodesk Inventor (Part 1)
11/29/2005-8:00 am - 11:30 am Room:Swan 1 (Swan) Walt Disney World Swan and Dolphin Resort Orlando, Florida Up to Cruising Speed with Autodesk Inventor (Part 1) Neil Munro - C-Cubed Technologies Ltd. and
Anchor Block Draft Tutorial
Anchor Block Draft Tutorial In the following tutorial you will create a drawing of the anchor block shown. The tutorial covers such topics as creating: Orthographic views Section views Auxiliary views
Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.
Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.
Foreword. If you have any questions about these tutorials, drop your mail to
Foreword The main objective of these tutorials is to give you a kick start using Solidworks. The approach to write this tutorial is based on what is the most important knowledge you should know and what
Starting a 3D Modeling Part File
1 How to Create a 3D Model and Corresponding 2D Drawing with Dimensions, GDT (Geometric Dimensioning and Tolerance) Symbols and Title Block in SolidWorks 2013-2014 By Edward Locke This tutorial will introduce
Evaluation Chapter by CADArtifex
The premium provider of learning products and solutions www.cadartifex.com EVALUATION CHAPTER 2 Drawing Sketches with SOLIDWORKS In this chapter: Invoking the Part Modeling Environment Invoking the Sketching
The Revolve Feature and Assembly Modeling
The Revolve Feature and Assembly Modeling PTC Clock Page 52 PTC Contents Introduction... 54 The Revolve Feature... 55 Creating a revolved feature...57 Creating face details... 58 Using Text... 61 Assembling
Autodesk AutoCAD Architecture 2015 Fundamentals
Autodesk AutoCAD Architecture 2015 Fundamentals Elise Moss SDC P U B L I C AT I O N S Authorized Author Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the
IT, Sligo. Equations Tutorial
Equations Tutorial Parametric Modelling: SolidWorks is a parametric modelling system where parameters, such as dimensions and relations, are used to create and control the geometry of the modelled part.
Activity 1.5.5a Pegboard Toy Working Drawings
Activity 1.5.5a Pegboard Toy Working Drawings Introduction Having the ability to take something that you have designed and create a 3D model of it is exciting and fun to do. In the last activity, you made
Generative Drafting (ISO)
CATIA Training Foils Generative Drafting (ISO) Version 5 Release 8 January 2002 EDU-CAT-E-GDRI-FF-V5R8 1 Table of Contents (1/2) 1. Introduction to Generative Drafting Generative Drafting Workbench Presentation
Nut and Bolt Tutorial
Thread Representations Nut and Bolt Tutorial Parts to a Thread Thread Dimensioning Major Diameter Thread Series (IE UNC, UNF, ACME, etc) ½ - 13 UNC 2 A or B A = External B = Internal Threads per Inch Class
Drawing and Detailing
Drawing and Detailing with SolidWorks 2007 By David C. Planchard and Marie P. Planchard Referencing the ASME Y14 Engineering Drawing and Related Documentation Practices SDC PUBLICATIONS Schroff Development
The Benefits of Using the Electrical Toolset in AutoCAD
The Benefits of Using the Electrical Toolset in AutoCAD A productivity study detailing the differences between AutoCAD and the Electrical toolset. Built specifically to create and modify electrical controls
REVIT - RENDERING & DRAWINGS
TUTORIAL L-15: REVIT - RENDERING & DRAWINGS This Tutorial explains how to complete renderings and drawings of the bridge project within the School of Architecture model built during previous tutorials.
Creo Parametric Primer
Creo Parametric Primer Creo Parametric Primer Education Editions 2 C2-SE-L1-004-1.0 Written by Tim Brotherhood and Adam Haas Conditions of use Acknowledgements Feedback tbrotherhood@ptc.com Product code
SolidWorks 95 User s Guide
SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents
Engineering Design with
Engineering Design with SOLIDWORKS 2016 and Video Instruction A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard, CSWP, SOLIDWORKS Accredited Educator SDC PUBLICATIONS
1: INTRODUCTION TO AUTOCAD
AutoCAD syllabus 1: INTRODUCTION TO AUTOCAD Starting AutoCAD AutoCAD Screen Components Drawing Area Command Window Navigation bar Status bar Invoking Commands in AutoCAD Keyboard Ribbon Application Menu
Upcoming Events This Week : LPQ
Upcoming Events This Week : LPQ Extracting Drawings - DEMO Although most demos are implemented with word documents, this demo employs slides so that more details can be shown to the students as the drawing
Laboratory Demonstration Exercises
Laboratory Demonstration Exercises 3-1 Lab Demo 1 - Plus Block Open SolidWorks, click on new document part OK. Right Click on Front Plane, click on Sketch icon (pencil w/ axes). In the sketch toolbar on
Table of Contents. Lesson 1 Getting Started
NX Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard