VEUE PIVOT ARM INSTALLATION MANUAL. February 2017
|
|
- Gavin Franklin
- 5 years ago
- Views:
Transcription
1 VEUE PIVOT ARM INSTALLATION MANUAL February 2017
2 CONTENTS February 2017 This manual is to be read in conjunction with the Product Specifications & Assembly manual SECTION NO. DESCRIPTION PAGE NO. SECTION 1 ITEMS REQUIRED 1.1 SECTION 2 INSTALLATION 2.1 PART A PREPARING INSTALLATION SPACE 2.1 PART B BOX INSTALLATION 2.2 PART C FASCIA INSTALLATION 2.4 PART D OPEN BRACKET INSTALLATION 2.6 PART E SHADE INSTALLATION 2.8 PART F ATTACH ARMS 2.10 PART G INSERT BOX / FASCIA 2.15 SECTION 3 TROUBLESHOOTING 3.1 DISCLAIMER INTRODUCTION This Installation manual has been produced by TEXTON to supply the necessary information for safe and correct installation of this system. INSTALLERS RESPONSIBILITY Before installing, please read & ensure you understand the safety information and installation instructions as defined in this installation manual. If you do not fully understand these instructions, contact TEXTON for clarification before installing. The Installer is responsible to ensure that all installation personnel have been adequately trained on the safe & correct installation and operation. The Installer is responsible to ensure that supporting structures are sound and can adequately support the load. The Installer is responsible to ensure that the devises used to anchor the product to the supporting structure are suitable for the application. SAFETY INFORMATION Ensure that electrical works are done only by a LICENSED ELECTRICIAN. DO NOT modify any of the components of this system. PERSONNEL REQUIREMENTS Only suitably trained/qualified personnel should undertake installation. DISCLAIMER TEXTON has used reasonable care in preparing the information included in this document, but makes no representations or warranties as to the completeness or accuracy of the information. Information is supplied upon the condition that the persons receiving the information will make their own determination as to its suitability for their purposes prior to use. TEXTON assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. TEXTON reserves the right to make changes without further notice to any products to improve reliability, function or design. COPYRIGHT COPYRIGHT TEXTON INC 2017 All rights reserved. No part of this document may be reproduced or utilized in any means, by any means, electronic or mechanical including photocopying, recordings, or by any information storage or retrieval system, without the express permission from TEXTON.
3 SECTION 1 ITEMS REQUIRED TOOLS REQUIRED Saw Saw Drill Screw Driver Philips Head & Flat Head Jaw Pliers Allen Key Set Mallet Scissors Measuring Tape Pencil ADDITIONAL ITEMS REQUIRED (NOT SUPPLIED) To assemble an VEUE PIVOT ARM, the following non-stocked items are required: Fasteners for Box/Open Brackets/Hardware (ensure appropriate fasteners are used to suit application) Trims to conceal packing (if required) Page 1.1
4 SHADE ITEMS REQUIRED BOX FASCIA or Fascia Bracket (RE xxx000) may be required as a centre support for larger spans OPEN BRACKETS or Page 1.2
5 SHADE ARMS Page 1.3
6 SECTION 2 INSTALLATION PART A PREPARING INSTALLATION SPACE STEP 1 CHECK FOR OBSTRUCTIONS Check for any obstructions that may interfere in installation. STEP 2 CHECK VERTICAL & HORIZONTAL INSTALLATION DIMENSIONS VERTICAL DIMENSIONS Check if top of installation space is level. If H1 H2, corrective actions may need to be considered prior to installation H1 H2 HORIZONTAL DIMENSIONS W1 If W2 W1, W1=Shade Width Note: Packing of Pivot Arm Bracket may be required W2 W1 If W2 < W1, by a value of: 0-20mm, Proceed to Part B (W1 = Shade Width) 20+, Consider corrective action to square installation space W2 Page 2.1
7 PART B BOX INSTALLATION STEP 1 INSTALL BOX TO WALL/CEILING WALL MOUNT Note: Use appropriate fasteners to suit application Ensure Box is Aligned and Level CEILING MOUNT Note: Use appropriate fasteners to suit application Ensure Box is Aligned and Level Page 2.2
8 INSIDE MOUNT Note: Use appropriate fasteners to suit application Ensure Box is Aligned and Level Page 2.3
9 PART C FASCIA INSTALLATION STEP 1 INSTALL END PLATES TO WALL/CEILING USING APPROPRIATE FASTENERS TO SUIT APPLICATION WALL MOUNT Fascia Bracket (RE xxx000) may be required as a centre support for larger spans Note: Use appropriate fasteners to suit application Ensure End Plates are aligned and level Measure brackets end to end to confirm measurement is correct CEILING MOUNT Fascia Bracket (RE xxx000) may be required as a centre support for larger spans Note: Use appropriate fasteners to suit application Ensure End Plates are aligned and level Measure brackets end to end to confirm measurement is correct Page 2.4
10 INSIDE MOUNT Fascia Bracket (RE xxx000) may be required as a centre support for larger spans Note: Use appropriate fasteners to suit application Ensure End Plates are aligned and level Measure brackets end to end to confirm measurement is correct Page 2.5
11 PART D OPEN BRACKET INSTALLATION STEP 1 INSTALL BRACKETS TO WALL/CEILING USING APPROPRIATE FASTENERS TO SUIT APPLICATION WALL MOUNT Note: Use appropriate fasteners to suit application Ensure Box is Aligned and Level Ensure brackets are aligned and level Measure brackets end to end to confirm measurement is correct CEILING MOUNT Note: Use appropriate fasteners to suit application Ensure Box is Aligned and Level Ensure brackets are aligned and level Measure brackets end to end to confirm measurement is correct Page 2.6
12 INSIDE MOUNT Note: Use appropriate fasteners to suit application Ensure Box is Aligned and Level Ensure brackets are aligned and level Measure brackets end to end to confirm measurement is correct Page 2.7
13 PART E SHADE INSTALLATION STEP 1 INSERT SHADE INTO BOX NOTE: Insert control end first Ensure shade is secure STEP 2 INSERT R-CLIP ONTO IDLER ADAPTER Ensure pin is clipped in securely Page 2.8
14 STEP 3 FEED THROUGH MOTOR CABLE (FOR MOTOR ONLY) STEP 4 RUN SHADE DOWN + CENTER STEP 5 TEST SHADE OPERATION For motor operation, ensure wiring is correct and motor is operating correctly. For gear operation, ensure operation is smooth. Once shade is operating correctly, proceed to SECTION 2 / Part G. Page 2.9
15 PART F ATTACH ARMS STEP 1 POSITION PIVOT ARMS X NOTE: FOR OPEN SHADE MEASURE FROM BOTTOM OF THE BRACKET PIVOT ARM POSITION ARM LENGTH 1m (39.37 ) 1.4m (55.12 ) TUBE OD 63mm (2.48 ) 78mm (3.07 ) 63mm (2.48 ) 78mm (3.07 ) X BOX 1050mm (41.33 ) 1030mm (40.55 ) 1450mm (57.09 ) 1430mm (56.30 ) OPEN 875mm (34.45 ) 880mm (34.65 ) 1275mm (50.20 ) 1280mm (50.39 ) Page 2.10
16 STEP 2 REMOVE BRACKET FROM PIVOT ARM BAR STEP 3 FIX ARM BRACKET AT PRE DETERMINED HEIGHT X X STEP 4 FIX PIVOT ARM BACK ONTO BRACKET Page 2.11
17 STEP 5 REMOVE CLAMP PIECE FROM PIVOT ARMS COMPLETE STEPS 5 8 IF THE CLAMP WAS NOT ALREADY ASSEMBLED ONTO THE BAR STEP 6 REMOVE ONE OF THE WEIGHT BAR END CAPS STEP 7 SLIDE PIVOT ARMS INTO WEIGHT BAR Page 2.12
18 STEP 8 INSTALL END CAP INTO WEIGHT BAR STEP 9 LOWER CLAMPS ON WEIGHT BAR ONTO PIVOT ARMS Page 2.13
19 STEP 10 TIGHTEN CLAMPS ONTO WEIGHT BAR STEP 11 REMOVE COVER OF PIVOT ARM PIVOT POINT AND REMOVE RETAINING PIN THEN RE INSTALL COVER NOTE: ARMS SHOULD BE FREE TO MOVE ONE PIN IS REMOVED Page 2.14
20 PART G INSERT BOX / FASCIA STEP 1 SWING BOX COVER INTO BOX TOP AND CLIP INTO PLACE STEP 2 SECURE COVER AT BOTH ENDS (IF REQUIRED) Page 2.15
21 STEP 3 TEST SHADE OPERATION NOTE: Ensure weight bar has correct clearance and that fabric does not rub against box cover. Page 2.16
22 INSTALLED WIRE GUIDE BOX OPEN Page 2.17
23 SECTION 3 TROUBLESHOOTING NO. PROBLEM CAUSE SOLUTION 1 Shade rolled up for an extended period of time. Installation is not square. Leave shade down for 1 4 hours; most ripples should disappear. Check box/brackets & shade roll are installed level. Ripples along sides of fabric 2 Shade does not fully open / jams 3 Uneven/twisted weight bar Fabric permanently damaged due to inadequate handling during assembly, transportation, installation or use. Spring inside pivot arms has been damaged. Crank may be damaged. Incorrect motor limits used. Shade roll is not level, thus weight bar appears uneven. Shade has been operated in excessive wind conditions. Fabric is not installed straight. Replace fabric and ensure it is handled with care. Replace arms. Replace crank. Refer to motor instructions to reset stop limits. Ensure shade is installed level. Check shade roll when the shade is fully raised. If ripples are evident on roll, open shade fully (without the presence of wind) to allow the shade to track down evenly. Raise and lower shade a number of times to check operation. Ensure fabric is assembled straight onto tube and weight bar. 4 Weight bar lifts up near bottom limit (motor control) Motor is FT (Fabric Tension) Mode Refer to motor instructions to deactivate FT Mode Page Copyright 2017
STRAIGHT DROP INSTALLATION MANUAL. February 2016
STRAIGHT DROP INSTALLATION MANUAL February 2016 CONTENTS February 2016 This manual is to be read in conjunction with the Product Specifications & Assembly manual SECTION NO. DESCRIPTION PAGE NO. SECTION
More informationZIPSCREEN EXTREME INSTALLATION MANUAL. May 2017
ZIPSCREEN EXTREME INSTALLATION MANUAL May 2017 CONTENTS May 2017 This manual is to be read in conjunction with the Product Specifications & Assembly manual SECTION NO. DESCRIPTION PAGE NO. SECTION 1 ITEMS
More informationRB12 AERO - SINGLE INSTALLATION MANUAL. April 2017
RB12 AERO - SINGLE INSTALLATION MANUAL April 2017 CONTENTS April 2017 This manual is to be read in conjunction with the Product Specifications & Assembly manual SECTION NO. DESCRIPTION PAGE NO. SECTION
More informationMOTORIZED STANDARD SHADE WITH CABLES Installation Instructions
Tools Needed Drill Measuring Tape Pencil 2 Level Plumb Line ¼ Masonry Drill Bit Hammer Linesmans Pliers Cable Cutters Phillips & Flat-Head Screw Driver 11/32 Socket or Open End Wrench 5/32 Allen Wrench
More informationInsolroll Clutch Operated Shades Installation Instructions Installation Instructions
All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.
More informationTools Needed Hardware Provided (per shade) Hardware Needed
Baby Grande or Grande Motorized (XQ5 Premium) Shade with Cables and Housing Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit Measuring Tape
More informationBaby Grande or Grande Crank Shade with Cables and Housing Installation Instructions
Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit Screwdriver (Flat & Phillips) Measuring Tape Pencil 4 Level Plumb Line ¼ Masonry
More informationBaby Grande or Grande Crank Shade with Cables and Housing Installation Instructions
Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit Screwdriver (Flat & Phillips) Measuring Tape Pencil 4 Level Plumb Line ¼ Masonry
More informationInstallation Operation Care
Installation Operation Care Provenance Woven Wood Shades Standard Cordlock CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount the
More informationBaby Grande with Crank, Housing, and Side Rails Installation Instructions
Baby Grande with Crank, Housing, and Side Rails Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil
More informationINSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger
INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger TOOLS REQUIRED FOR INSTALLATION: Drill motor, (1) 5/16 inch drill bit, (1) 13/64 drill bit, (1) 3/16 inch hex wrench (1) 3/32 inch hex wrench.
More informationInstallation Instructions Parasol Cellular Shades
Installation Instructions Parasol Cellular Shades SlideArch CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview... Mount the Installation s Inside
More informationBlackout Instructions. 4 R-Series Fascia Installation Outside Mount
Blackout Instructions 4 R-Series Fascia Installation Outside Mount 1 Components Needed page 3 Tools Needed page 4 System Diagram page 5 Instructions Step 1: Install Brackets. Page 6 Step 2: Mount Back
More informationInstallation And Care Instructions. Vertical Honeycomb Shades
Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...
More informationMotorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions
Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips
More informationVertical Honeycomb Shades
Step by Step Installation Instructions Vertical Honeycomb Shades Customer Service 800.248.8888 or visit us online at smithandnoble.com Thank you for purchasing from Smith+Noble. Your new shades have been
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5 Tools Required...6
More informationInstallation Operation Care
Installation Operation Care Provenance Woven Wood Shades Standard Cordlock CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview...3 Mount the Standard
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades 52 C8-10-3401 Rev 2/14 CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5
More informationInstallation Operation Care
Installation Operation Care Provenance Woven Wood Shades Standard Cordlock CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview...3 Mount the Standard
More informationInstallation Operation Care
Installation Operation Care Provenance Woven Wood Shades Standard Cordlock CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount the
More informationInstallation Operation Care. Solera Soft Shades EasyRise, UltraGlide, and LiteRise Lifting System
Installation Operation Care Solera Soft Shades EasyRise, UltraGlide, and LiteRise Lifting System CONTENTS GETTING STARTED Product Views...1 Tools and Fasteners Needed...3 INSTALLATION Installation Overview...4
More informationROOM FOLD SLIDING FOLDING INTERNAL DOORSET FITTING & FIXING GUIDELINES
EDITION 7 ROOM FOLD SLIDING FOLDING INTERNAL DOORSET IMPORTANT You can only assemble these door configurations by using the frame provided. Your warranty will be invalid if other alternatives are used.
More informationDeckRail A Product of DeckRite LLC 3912 East Progress North Little Rock, AR Phone: (501) Fax: (501)
Disclaimer: Deck Rail Glass Railing Installation Guide This guide is not intended to replace a trained professional installer. The drawings and instructions contained within are for demonstration purposes
More informationInstallation Operation Care. Sonnette Cellular Roller Shades. LiteRise Operating System
Installation Operation Care Sonnette Cellular Roller Shades LiteRise Operating System CONTENTS GETTING STARTED: Product View...1 Tools and Fasteners Needed...2 INSTALLATION: Installation Overview...3 Mount
More informationCorded Honeycomb Shades
Corded Honeycomb Shades Remove shade from package. Save packaging until shade is installed and working to your satisfaction. Level Tape Measure Pencil Power drill Screwdriver s for different mounting surface:
More informationHow to Install Custom Real Wood and Faux Wood Blinds
Before you begin your installation: READ ALL INSTALLATION INSTRUCTIONS! Make sure that you have all tools and hardware needed for installation. Check the installation surface (wall, ceiling, or window
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationN. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from
More informationInstallation, Operation and Care Instructions. Continuous Cord Loop Operating System
Installation, Operation and Care Instructions Continuous Cord Loop Operating System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3
More informationCordless Operable Sidelights
Installation Instructions Parasol Cellular Shades Cordless Operable Sidelights CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview... Mount the
More informationSetup. The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on series tables.
Faraday CageSetup, 2017 Setup The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on 63-500 series tables. Cage with a base plate for use on a
More informationSectional Door Installation Instructions
Sectional Door Installation Instructions 1. Check opening height and door size. a. 25-30mm overlap on each side and >10mm at top. b. At least 150mm side room required 2. Check headroom clearance, standard
More informationInstallation Operation Care
Installation Operation Care Designer Banded Shades Cassette with Custom Clutch and UltraGlide CONTENTS Getting Started Product View Custom Clutch... 1 Product View UltraGlide... 2 Tools and Fasteners Needed...
More informationMETAL BLINDS. Deluxe GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE
METAL BLINDS Deluxe GETTING STARTED OPTIONAL HARDWARE A few simple tools are required: Steel Tape Measure Pencil Level Hold Down Brackets with Screws Extension Bracket Power Drill and Drill Bits Flathead
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for Fortress Horizontal Cable Panel System with UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all
More informationQuick Fit Installation Guide Retractable Screen - Double Door
Quick Fit Installation Guide Retractable Screen - Double Door 1 REMOVE KIT PARTS FROM SHIPPING TUBE 2 Slide bolts 2 Rail receiver Clips 15 Mounting screws 1 Housing end cap screw 2 Handles 1 Housing end
More informationInstallation Operation Care
Installation Operation Care Designer Roller and Designer Screen Shades Standard and Cassette Cordless Lifting System CONTENTS Getting Started: Product Views... 1 Tools and Fasteners Needed... 3 Installation
More informationOwner s Guide. Roller Shades. Clutch Operated Standard Shades
Owner s Guide Roller Shades Clutch Operated Standard Shades CONTENTS Product View...4 Introduction...5 Getting Started...5 Tools And Fasteners Needed...5 Install The Mounting Brackets...6 Install The
More informationInstallation Operation Care. Duette Honeycomb Shades EasyRise Lifting System
Installation Operation Care Duette Honeycomb Shades EasyRise Lifting System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount the
More informationModel MSPPWRTW Large Flat Panel Single Arm Wall Mount
INSTALLATION INSTRUCTIONS Model Large Flat Panel Single Arm Wall Mount The is wall-mounted, rugged, versatile, and installer-friendly. The mount is compatible with the standard (14 x 14 ) PSB interface
More informationSolar & Roller Shades
STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades Cordless Control with Mounting Bar or Cordless Control with Cassette Table of Contents Step 1 - Getting Started.... 3 Everything You Need A
More informationClassic SportBar Camaro V6 or V8
Classic SportBar 2011-2015 Camaro V6 or V8 The Classic SportBar is intended for restyling purposes only and does NOT provide roll over protection. Read entire installation guide before starting. Component
More informationDeckRail A Product of DeckRite LLC 3912 East Progress North Little Rock, AR Phone: (501) Fax: (501)
Deck Rite Welded Picket Railing Installation Guide Disclaimer: This guide is not intended to replace a trained professional installer. The drawings and instructions contained within are for demonstration
More informationInstallation, Operation and Care Instructions. Retractable Cord Operating System
Installation, Operation and Care Instructions Retractable Cord Operating System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount
More informationDUETTE LITERISE SHADES INSTALLATION OPERATION CARE
DUETTE LITERISE SHADES INSTALLATION OPERATION CARE PRODUCT VIEW Installation Brackets Headrail with Fabric-Covered Valance End Cap Middle Rail Bottom Up Shade Bottom Rail Handle Duolite Not Shown: Top
More informationCloset Carousel Installation Instructions. Models TKA 5 Through TKA 14 Equipped with Footswitch Controls
Tools Required: Phillips Screwdriver (#2) Adjustable Wrench Level Tape Measure Utility Knife Electric Drill Drill Bits for Anchors Ladder (4 foot) Models TKA 5 Through TKA 14 Equipped with Footswitch Controls
More informationTRACK TYPE DISCLAIMER. THESE INSTRUCTIONS ARE INTENDED FOR PROFESSIONAL GARAGE DOOR INSTALLERS and only apply to the fittings
TRACK TYPE INSTALLTION INSTRUCTIONS DISCLAIMER THESE INSTRUCTIONS ARE INTENDED FOR PROFESSIONAL GARAGE DOOR INSTALLERS and only apply to the fittings Note: All references are taken from inside looking
More informationInstallation Operation Care
Installation Operation Care Applause Honeycomb Shades LiteRise Operating System with TrimKit Contents GETTING STARTED Product View... 1 Tools and Fasteners Needed... 2 INSTALLATION Installation Overview...
More informationRetractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors)
Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors) IMPORTANT: Please read before you begin. Table of Contents
More informationT-FITTINGS INSTALLATION INSTRUCTIONS
T-FITTINGS INSTALLATION INSTRUCTIONS DISCLAIMER THESE INSTRUCTIONS ARE INTENDED FOR PROFESSIONAL GARAGE DOOR INSTALLERS and only apply to the fittings Note: All references are taken from inside looking
More informationSolar & Roller Shades
STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades Cordless Control with Mounting Bar or Cordless Control with Cassette Everything You Need A Smooth Set-Up We want you to love your new window
More informationInstallation Operation Care
Installation Operation Care Applause Honeycomb Shades LiteRise Operating System Contents GETTING STARTED Product View...1 Tools and Fasteners Needed...2 INSTALLATION Installation Overview...3 Mount the
More informationINSTALLATION MANUAL PBL-UMP
INSTALLATION MANUAL PBL-UMP Table of Contents Warning Statements... 4 Parts List... 5 Installation Tools... 5 Features... 7 Projector Preparation... 8 Bracket Installation... 10 Leveling the Mounting Bracket...
More informationPremium Light Filtering Sheer Shade
Premium Light Filtering Sheer Shade Installation Instructions Email: customerservice@blindster.com Call us: (888) 256-8672 Mon - Fri 8am - 7pm (CT) Congratulations on purchasing a Premium Light Filtering
More informationFLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationInstallation Operation Care
Installation Operation Care Alustra Woven Textures Traditional Roman Shades Cordlock Lifting System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Mounting Types and Window
More informationDiva Acoustical Ceiling
Installation Instructions Diva Acoustical Ceiling CONTENTS Important User Information...........................2 Safety Precautions.................................3 Required Tools....................................3
More informationHeavy Duty Ceiling Tilt Mount Installation Manual
HD-CTM-5580 Heavy Duty Ceiling Tilt Mount Installation Manual *This Installation requires a minimum of two people. For your safety: Read the complete instruction manual before starting an installation
More informationQuick Fit Installation Guide Retractable Screen - Single Door
Quick Fit Installation Guide Retractable Screen - Single Door 1 REMOVE KIT PARTS FROM SHIPPING TUBE 15 Mounting screws 1 Housing end cap screw 2 Handles 1 Housing end cap 1 Bushing 1 Pull bar end cap 2
More informationNocturne+ E INSTRUCTIONS CAUTION. Motor Operated Exterior Projection Screen. 1¾ (45mm) END CAP. Wall Mounting Bracket. Wall Mounting Bracket
Motor Operated Exterior Projection Screen Wall ing Bracket INSTRUCTIONS INSTALLATION & OPERATION CAUTION Wall ing Bracket 1. Inspect all boxes to make sure you have received the proper screen and parts.
More informationArticulating TV/Monitor Wall Mount Model: WA300S (Butterfly Series)
P Articulating TV/Monitor Wall Mount Model: WA300S (Butterfly Series) Instruction Manual Images may different from actual product Disclaimer It is Dyconn s intention to have all the correct information
More informationOwner s Guide. Pirouette Window Shadings. Standard EasyRise Rectangular And Two-On-One Headrail Shadings
Owner s Guide Pirouette Window Shadings Standard EasyRise Rectangular And Two-On-One Headrail Shadings Contents Introduction...3 Product View...4 Getting Started...5 Mount The Installation Brackets...6
More informationa.k.a. casegoods instructions
a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly
More informationU.S. Rack, Inc Falcon Drive, Madera, CA APR17 INSTALLATION AND USE INSTRUCTIONS for SIDE-MOUNT LADDER RACK
U.S. Rack, Inc. 2850 Falcon Drive, Madera, CA 93637 15APR17 INSTALLATION AND USE INSTRUCTIONS for SIDE-MOUNT LADDER RACK WARNING: Do NOT attempt to install or use this rack without following all instructions.
More informationHANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT
HANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT Introduction SECTION 1 Thank you for purchasing one of our fine True Focus products. This manual covers the
More informationStar Trac Turbo Trainer Assembly & Setup
Star Trac Turbo Trainer Use the following procedures to unpack and assemble your Turbo Trainer manufactured by Star Trac. UNPACKING AND PARTS LIST Position the shipping carton so the Heavy End logo is
More informationWHISPER Cellular EasyRise Shades. Installation Operation Care
WHISPER Cellular EasyRise Shades Installation Operation Care 05/2013 CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mounting Types
More informationATLANTIS RAIL Contact Information
ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing
More informationPRODUCT INFORMATION MANUAL SECTION: 9F-1 DUETTE ULTRAGLIDE LIFTING SYSTEM DUETTE SIGNATURE ULTRAGLIDE LIFTING SYSTEM
DUETTE SIGNATURE ULTRAGLIDE LIFTING SYSTEM Product View Installation Brackets UltraGlide Standard Wand Top-Down/Bottom-Up Duolite REPLACES ISSUE DATE: APPROVED BY: D.ALTIPARMAKOVA PAGE 3 Thank you for
More informationESA-200 Fixed Sidelite
Exterior View Installation Instructions For use with ESA II Controller 1 Tools Required: Suggested Fasteners Required - (Not supplied) Screwdrivers Small Straight (FlatBlade) - for Terminal Block wiring
More informationLEGENDS RETRACTABLE DOOR SCREENS
LEGENDS RETRACTABLE DOOR SCREENS MAGNETIC LATCHING DESIGN SYSTEM 42 I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess
More informationx2 1/4 (6mm) Floor Anchor
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Straight Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm
More informationKwik-Lock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Installation Instructions Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationPRODUCT: LOKI INSTALLATION INSTRUCTIONS. Product is covered by U.S. patents. For more information visit
R INSTALLATION INSTRUCTIONS PRODUCT: LOKI CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED TOOLS
More informationInstallation Operation Care
Installation Operation Care Duette Honeycomb Shades UltraGlide Lifting System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount
More informationClearSpan Hydroponic Table Kit
ClearSpan Hydroponic Table Kit Hydroponic Table Kit (The 109314 (4' x 16') model is shown.) Designed to grow healthy plants without soil using mineral-nutrient solutions. 2009 ClearSpan All Rights Reserved.
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for FortressCable H-Series Cable Panel System With UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain
More informationTAMBOUR DOOR SYSTEMS. Construction Automotive Industry
TAMBOUR DOOR SYSTEMS C3 Installation instructions www.rehau.com Construction Automotive Industry C3 Parts Overview 8 1 Slats 2 Handle 6 7 3 Handle gliders 4 Track cover 5 1 9 5 Track base 6 End caps 4
More informationINSTRUCTION BOOK FOR. IDEA Screen & Panoramic for Nureva Span
INSTRUCTION BOOK FOR IDEA Screen & Panoramic for Nureva Span Disclaimer Milestone and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete.
More information00108/00110 INSTRUCTION MANUAL
00108/00110 INSTRUCTION MANUAL Removable and Adjustable Mudflap System IMPORTANT! Exhaust Systems Note: Any modifications to the factory installed exhaust system may void your manufacturer s warranty.
More informationInstallation Guide. Overview
Installation Guide Thank you for selecting a DuctSox SkeleCore Pull-Tight with Track System. This guide will be helpful for installing the system. The key to a successful SkeleCore Pull-Tight installation
More informationDeluxe Exterior Solar Shades
Deluxe Exterior Solar Shades Installation Instructions Email: customerservice@blindster.com Call us: (888) 256-8672 Mon - Fri 8am - 7pm (CT) Thank you for purchasing Deluxe Exterior Solar Shades from Blindster.
More informationReady-To-Assemble VersaRail INSTALLATION INSTRUCTIONS
FREEDOM-WEB Ready-To-Assemble VersaRail INSTALLATION INSTRUCTIONS Read all instructions prior to installing product. Refer to manufacturers safety instructions when operating any tools. To register your
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationInstallation Guide. Deckorum. Composite Decking
Installation Guide Deckorum Composite Decking 1. Introduction Welcome to Deckorum Installation Guide Please fully read the installation guide before commencing any installation works. This will provide
More informationTaurean Sectional Garage Door INSTALLATION INSTRUCTIONS
BEFORE YOU BEGIN MAKE SURE THESE INSTRUCTIONS ARE READ AND UNDERSTOOD COMPLETELY. THESE INSTRUCTIONS ARE INTENDED FOR PROFESSIONAL GARAGE DOOR INSTALLERS. ALL REFERENCES ARE TAKEN FROM THE INSIDE LOOKING
More informationSelect Lab Fixed Height Workstation
Assembly Instructions Select Lab Fixed Height Workstation Contents Important User Information.............................. 2 Safety Precautions.................................... 3 Required Tools........................................
More informationNew Roman Shades WARNING. Installation Operation Care. Retractable Cord Lifting System
CHILD SAFETY Warning WARNING For more safety information call 1-888-501-8364 in the U.S. or 1-866-662-0666 in Canada. Young children can wrap cords around their necks and STRANGLE. Always keep cords out
More informationClearSpan End Frame Kit 26' Wide x 12' High
ClearSpan End Frame Kit 26' Wide x 12' High Diagram shows the end frame kit for an end wall without a door. (Door and end panel are purchased separately.) Rafter and struts shown in the above diagram are
More informationRULTRACT RETRACTOR CABLE REPLACEMENT INSTRUCTIONS. Rultract, Inc. is the ONLY authorized service center in the U.S.A.
RULTRACT RETRACTOR CABLE REPLACEMENT INSTRUCTIONS Rultract, Inc. is the ONLY authorized service center in the U.S.A. When your Rultract instrument needs repair or service, contact Rultract Inc. or Rultract
More informationFigure A. Figure B. Figure C. Figure D
Xsite 1 Power/Data Tile and Components Tools Required Tape Measure Cordless Drill/Driver #2 Phillips Screw driver bit Rubber Mallet Flat Blade Screwdriver Figure A Hardware Required Provided as shown Installation
More informationInstallation Instructions for Vista Air Vertically Folding Walls
Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.
More informationMcCue Bumper Installation Instructions
McCue Bumper Installation Instructions McCue 8" Bumper Tools Required: Saw with 10-12" blade Tape measure Flat head screwdriver Phillips screw driver Pencil or chalk line Drill with Philips driver bit
More informationROLL-A-GLIDE INSULATED ROLLER DOOR
ROLL-A-GLIDE INSULATED ROLLER DOOR Installation Instructions 1. Motor 13. Brush / Wear Strips 2. Axle Assembly 14. Curtain Assembly 3. Rigid Link Collars 15. Door Laths 4. Octagonal Plug End 16. Locking
More informationBrother Industries, Ltd. Nagoya, Japan
4. 2001. This service manual has been compiled for explaining repair procedures of the MODEL XL-6562, XL6452, XR- 46. This was produced based on up-to-date product specifications at the time of issue,
More informationMETALWORKS Concealed. Installation Instructions
METALWORKS Concealed Installation Instructions 1. GENERAL 1.1 Product Description MetalWorks Concealed ceilings consist of perforated and unperforated panels that are downward accessible, and are designed
More informationTM TM DOG HOUSE Age 9+
TM TM DOG HOUSE Age 9+ Safety First! Use eye protection, always! Use ear protection with loud power tools Stay with kids while they work! Follow tool manufacturers safety guidelines This project is recommended
More information