Uncooled Mini-DIL 980nm Pump Laser Module LU97**2-R Features: Up to 300mW kink-free power over full operating temperature range Operating temperature range from 0 C to +70 C (case) Polarization maintaining (PM) fibre Low power dissipation Laser chip and package design with submarine reliability The II-VI LU97**2-R uncooled Mini-DIL 980nm pump laser module is the second generation uncooled pump module providing higher power for highly reliable amplification for metro, cross-connect or other single/multi-channel amplification applications. The LU97**2-R uses a Mini-DIL package enabling low-cost and small form-factor. The G07 ridge-waveguide laser diode inside has been designed for uncooled operation at high temperature and power levels. Submarine qualification of the G07 chip ensures high reliability even at 270mW operating power, 70 C. External Fiber Bragg Grating (FBG) stabilization provides excellent wavelength and power stability over the entire temperature operating range. Wavelength stabilized by fiber Bragg grating over entire operating range Centre wavelength at 974 and 976nm Applications: Telcordia GR-468-CORE compliant RoHS compliant EDFA or EDWA requiring low-tomedium optical power with low power consumption and small formfactor package
Optical Characteristics Conditions unless otherwise stated: Case temperature 0 to 70 C Monitor diode bias -5V CW operation Kink Free Power (mw) Operating Power (mw) (974nm product) (976nm product) 110 100 LU974C2-R LU976C2-R 120 110 LU974D2-R LU976D2-R 135 120 LU974E2-R LU976E2-R 145 130 LU974F2-R LU976F2-R 155 140 LU974G2-R LU976G2-R 165 150 LU974H2-R LU976H2-R 175 160 LU974J2-R LU976J2-R 190 170 LU974K2-R LU976K2-R 200 180 LU974L2-R LU976L2-R 210 190 LU974M2-R LU976M2-R 220 200 LU974N2-R LU976N2-R 230 210 LU974P2-R LU976P2-R 245 220 LU974R2-R LU976R2-R 255 230 LU974S2-R LU976S2-R 265 240 LU974T2-R LU976T2-R 275 250 LU974U2-R LU976U2-R 285 260 LU974V2-R LU976V2-R 300 270 LU974W2-R LU976W2-R Operating power assumes a 10% ageing margin: Operating Power = Kink-Free Power/1.1 Notes: Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by II-VI before they become applicable to any particular order or contract. In accordance with the II-VI policy of continuous improvement specifications may change without notice. Further details are available from any II-VI sales representative. 2
Product Specification Parameter Min Typ Max Unit Conditions Threshold current 55 80 ma At 70 C case temperature Operating current 100mW 110mW 120mW 130mW 140mW 150mW 160mW 170mW 180mW 190mW 200mW 210mW 220mW 230mW 240mW 250mW 260mW 270mW 225 240 255 270 290 305 320 335 350 370 385 400 415 430 445 460 475 490 260 280 305 325 345 365 390 410 430 455 475 500 520 540 560 585 605 620 ma At 0 C to 70 C case temperature Operating forward voltage 1.75 2.0 V 270mW, 70 C Centre wavelength LU974*2-R LU976*2-R 973 975 974 976 975 977 Spectral width at -13dB 0.2 1.0 nm nm 0 C to 70 C FBG temperature is 25 C Power in band ratio 90 % c±1.5nm; 0 C to 70 C Temperature dependence of peak wavelength Monitor diode responsivity 0.3 1.1 15 µa/mw 0.008 0.01 nm/c FBG temperature dependency Photodiode dark current 50 na -5V bias voltage Fibre power stability 10 270mW 0.10 0.15 db Peak-to-peak Time = 60sec DC to 50kHz Return loss (RL) 8 db 1500nm 1600nm Thermistor BETA value 3539 3575 3611 ±1% temperature variation Thermistor resistance 9.5 10.0 10.5 kω At case temperature set to 25 C Total power consumption 1.0 1.35 W Tcase= 70C, 270mW 3
Absolute Maximum Ratings Parameter Min Typ Max Unit Conditions Operating case temperature 0 70 C Storage temperature -40 85 C Storage relative humidity 5 95 % Operating relative humidity 5 85 % Pigtail axial pull force 10.0 N 3x10 seconds Pigtail side pull force 5.0 N 3x10 seconds Fiber bend radius 13 mm Lead soldering temperature 350 C 10 sec Laser diode forward current Tcase = 0 C Tcase = 25 C Tcase = 70 C 900 900 800 ma But not to exceed 0.024kg of water per 1.0kg of dry air Laser diode reverse current 10 μa Reverse voltage <2V Laser diode reverse voltage 2.5 V Photodiode reverse voltage 20 V Photodiode reverse current 5 ma ESD threshold 500 V HBM, C=100pF, R=1.5kΩ CW Fibre Specification Parameter Min Typ Max Unit Conditions Fibre type Nufern PM980-HP or Corning PM 98-U25A/D Cut-off wavelength 830 900 970 nm Mode field diameter 5.6 6.6 7.6 µm @ 980nm Cladding diameter 124 125 126 µm Fibre coating diameter 230 245 260 µm Grating recoat diameter 260 280 300 µm Core/cladding concentricity <0.5 µm Coating-clad offset 5 µm Fibre proof test 200 kpsi Fibre Bragg Grating proof test 150 kpsi Acrylate material, mechanically strippable Fibre termination; bare fibre with rough cleave. 4
Module Outline Drawing and Pin Connections Figure 1: Package Outline Drawing and Dimensions (mm) 5
RoHS Compliance II-VI is fully committed to environment protection and sustainable development and has set in place a comprehensive program for removing polluting and hazardous substances from all of its products. The relevant evidence of RoHS compliance is held as part of our controlled documentation for each of our compliant products. RoHS compliance parts are available to order, please refer to the ordering information section for further details. Ordering Information: Please refer to the product codes as given in the table. Kink Free Power (mw) Operating Power (mw) (974nm product) (976nm product) 110 100 LU974C2-R LU976C2-R 120 110 LU974D2-R LU976D2-R 135 120 LU974E2-R LU976E2-R 145 130 LU974F2-R LU976F2-R 155 140 LU974G2-R LU976G2-R 165 150 LU974H2-R LU976H2-R 175 160 LU974J2-R LU976J2-R 190 170 LU974K2-R LU976K2-R 200 180 LU974L2-R LU976L2-R 210 190 LU974M2-R LU976M2-R 220 200 LU974N2-R LU976N2-R 230 210 LU974P2-R LU976P2-R 245 220 LU974R2-R LU976R2-R 255 230 LU974S2-R LU976S2-R 265 240 LU974T2-R LU976T2-R 275 250 LU974U2-R LU976U2-R 285 260 LU974V2-R LU976V2-R 300 270 LU974W2-R LU976W2-R Contact Information www.laserenterprise.com Important Notice Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by II-VI before they become applicable to any particular order or contract. In accordance with the II-VI policy of continuous improvement specifications may change without notice. Further details are available from any II-VI sales representative. INVISIBLE LASER RADIATION AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION CLASS 4 LASER PRODUCT Maximum Power >500 mw Wavelength >970nm REFERENCE IEC 60825-1 Ed 2.0 2007 D00382-PB Issue 02. Mar. 2013 II-VI 2014. II-VI the II-VI, Inc. logo, and all other II-VI, Inc product names and slogans are trademarks or registered trademarks of II-VI, Inc. in the U.S.A. or other countries. Products described in this datasheet may be covered by one or more patents in the U.S.A. and abroad. Information in this datasheet is subject to change without notice. 6