Simulation of Distributed Power-Flow Controller (Dpfc)

Similar documents
A Facts Device: Distributed Power-Flow Controller (DPFC)

Shunt Active Filters (SAF)

Research on Controller of Micro-hydro Power System Nan XIE 1,a, Dezhi QI 2,b,Weimin CHEN 2,c, Wei WANG 2,d

Figure.1. Basic model of an impedance source converter JCHPS Special Issue 12: August Page 13

STUDY OF MATRIX CONVERTER BASED UNIFIED POWER FLOW CONTROLLER APPLIED PI-D CONTROLLER

Micro-grid Inverter Parallel Droop Control Method for Improving Dynamic Properties and the Effect of Power Sharing

Design of Shunt Active Filter for Harmonic Compensation in a 3 Phase 3 Wire Distribution Network

antenna antenna (4.139)

To: Professor Avitabile Date: February 4, 2003 From: Mechanical Student Subject: Experiment #1 Numerical Methods Using Excel

High Speed ADC Sampling Transients

A method to reduce DC-link voltage fluctuation of PMSM drive system with reduced DC-link capacitor

ECE 2133 Electronic Circuits. Dept. of Electrical and Computer Engineering International Islamic University Malaysia

Modelling and Simulation of STATCOM for Reactive Power and Voltage Control.

Calculation of the received voltage due to the radiation from multiple co-frequency sources

Modeling and Control of a Cascaded Boost Converter for a Battery Electric Vehicle

Voltage Quality Enhancement and Fault Current Limiting with Z-Source based Series Active Filter

High Speed, Low Power And Area Efficient Carry-Select Adder

Active and Reactive Power Control of DFIG for Wind Energy Conversion Using Back to Back Converters (PWM Technique)

TECHNICAL NOTE TERMINATION FOR POINT- TO-POINT SYSTEMS TN TERMINATON FOR POINT-TO-POINT SYSTEMS. Zo = L C. ω - angular frequency = 2πf

Improvement of System Reliability & Power Transfer Capability using Distributed Power- Flow Controller (DPFC)

Walsh Function Based Synthesis Method of PWM Pattern for Full-Bridge Inverter

PRACTICAL, COMPUTATION EFFICIENT HIGH-ORDER NEURAL NETWORK FOR ROTATION AND SHIFT INVARIANT PATTERN RECOGNITION. Evgeny Artyomov and Orly Yadid-Pecht

Dual Functional Z-Source Based Dynamic Voltage Restorer to Voltage Quality Improvement and Fault Current Limiting

A Current Differential Line Protection Using a Synchronous Reference Frame Approach

Comparative Analysis of Reuse 1 and 3 in Cellular Network Based On SIR Distribution and Rate

The Effect Of Phase-Shifting Transformer On Total Consumers Payments

NATIONAL RADIO ASTRONOMY OBSERVATORY Green Bank, West Virginia SPECTRAL PROCESSOR MEMO NO. 25. MEMORANDUM February 13, 1985

IEE Electronics Letters, vol 34, no 17, August 1998, pp ESTIMATING STARTING POINT OF CONDUCTION OF CMOS GATES

IDENTIFICATION AND MITIGATION OF POWER QUALITY DISTURBANCES USING IUPQC BASED ON PSODV TECHNIQUE

Passive Filters. References: Barbow (pp ), Hayes & Horowitz (pp 32-60), Rizzoni (Chap. 6)

Low Switching Frequency Active Harmonic Elimination in Multilevel Converters with Unequal DC Voltages

High Gain Soft-switching Bidirectional DC-DC Converters for Eco-friendly Vehicles

A Single-Phase Dual-Stage PV-Grid System with Active Filtering

RC Filters TEP Related Topics Principle Equipment

A Novel Soft-Switching Two-Switch Flyback Converter with a Wide Operating Range and Regenerative Clamping

POWER FLOW ANALYSIS OF POWER SYSTEM EMBEDDED WITH UPFC USING PSASP PROGRAM

FAST ELECTRON IRRADIATION EFFECTS ON MOS TRANSISTOR MICROSCOPIC PARAMETERS EXPERIMENTAL DATA AND THEORETICAL MODELS

Modeling and Analysis of DPFC to Improve Power Quality

Control of Chaos in Positive Output Luo Converter by means of Time Delay Feedback

Time-frequency Analysis Based State Diagnosis of Transformers Windings under the Short-Circuit Shock

29. Network Functions for Circuits Containing Op Amps

Study on Shunt Active Power Filter with Improved Control Method Yaheng Ren1,a*, Xiaozhi Gao2,b, Runduo Wang3,c

Implementation of Fan6982 Single Phase Apfc with Analog Controller

Digital Transmission

Comparison of Reference Compensating Current Estimation Techniques for Shunt Active Filter

MTBF PREDICTION REPORT

Fuzzy Logic Controlled Shunt Active Power Filter for Three-phase Four-wire Systems with Balanced and Unbalanced Loads

Strain Gauge Measuring Amplifier BA 660

An Improved Active Filter Technique for Power Quality Control under Unbalanced Dynamic Load Condition

AFV-P 2U/4U. AC + DC Power Solutions. series. Transient Generation for Disturbance Tests. only. High Performance Programmable AC Power Source

A study of turbo codes for multilevel modulations in Gaussian and mobile channels

ECE315 / ECE515 Lecture 5 Date:

Triferential Subtraction in Strain Gage Signal Conditioning. Introduction

Controller Design Using Coefficient Diagram Methods for Matrix Converter Based Unified Power Flow Controllers

Model Reference Current Control of a Unipolar Induction Motor Drive

Development of a High Bandwidth, High Power Linear Amplifier for a Precision Fast Tool Servo System

Aalborg Universitet. Published in: I E E E Transactions on Industrial Electronics. DOI (link to publication from Publisher): /TIE.2014.

Unified Power Quality Conditioner (UPQC) During Voltage Sag and Swell

Improvement of the Shunt Active Power Filter Dynamic Performance

Closed Loop Topology of Converter for Variable Speed PMSM Drive

Interharmonic Mitigation Using Boost Converter In Variable Speed Drives

Static Voltage and Frequency Regulation of Standalone Wind Energy Conversion System

Sensors for Motion and Position Measurement

Soft-Switched CCM Boost Converter with High Voltage Gain for High Power Applications

Available online at ScienceDirect. Procedia Engineering 202 (2017)

Converter Rating Powers of Unified Power Flow Controller

Dynamic Optimization. Assignment 1. Sasanka Nagavalli January 29, 2013 Robotics Institute Carnegie Mellon University

An active damper for stabilizing power electronics-based AC systems Wang, Xiongfei; Blaabjerg, Frede; Liserre, Marco; Chen, Zhe; He, J.; LI, Y.

Graph Method for Solving Switched Capacitors Circuits

Performance Of Distributed Power Flow Controller (DPFC) Under Fault Condition

Latency Insertion Method (LIM) for IR Drop Analysis in Power Grid

Designing Of Distributed Power-Flow Controller

HARMONIC ANALYSIS USING SHUNT ACTIVE FILTER

Evolutionary Programming for Reactive Power Planning Using FACTS Devices

Power Flow Control Analysis of Transmission Line Using Static VAr Compensator (SVC)

CHAPTER 4 INSTANTANEOUS SYMMETRICAL COMPONENT THEORY

HIGH STEP-UP DC-DC CONVERTER FOR FUEL CELL POWERED RESIDENTIAL POWER GENERATION SYSTEM

Three-Phase Low-Frequency Commutation Inverter for Renewables

An Adaptive Over-current Protection Scheme for MV Distribution Networks Including DG

Selective Harmonic Mitigation Technique for Cascaded H-Bridge Converters with Equal DC Link Voltages

Control of Venturini Method Based Matrix Converter in Input Voltage Variations

Digital Differential Protection of Power Transformer Using Matlab

THE ARCHITECTURE OF THE BROADBAND AMPLIFIERS WITHOUT CLASSICAL STAGES WITH A COMMON BASE AND A COMMON EMITTER

Uncertainty in measurements of power and energy on power networks

A Simple, Efficient, and EMI-Optimized Solar Array Inverter

Impact of Multi-Terminal HVDC Grids on Enhancing Dynamic Power Transfer Capability

Customer witness testing guide

Application of Intelligent Voltage Control System to Korean Power Systems

Title Power electronic interfaces in Micro grids. Dejene

The Power Quality Compensation Strategy for Power Distribution System Based on Hybrid Parallel Active Power Filters

AC-DC CONVERTER FIRING ERROR DETECTION

Smart Grid Technologies for Reactive Power Compensation in Motor Start Applications

Research of Dispatching Method in Elevator Group Control System Based on Fuzzy Neural Network. Yufeng Dai a, Yun Du b

Harmonic Balance of Nonlinear RF Circuits

A Comparison of Two Equivalent Real Formulations for Complex-Valued Linear Systems Part 2: Results

POLYTECHNIC UNIVERSITY Electrical Engineering Department. EE SOPHOMORE LABORATORY Experiment 1 Laboratory Energy Sources

Equivalent Circuit Model of Electromagnetic Behaviour of Wire Objects by the Matrix Pencil Method

Error of Varhour Meter s Registration in the Presence of Harmonics

D-STATCOM Optimal Allocation Based On Investment Decision Theory

Fractional order PI based STATCOM and UPFC controller to diminish subsynchronous resonance

Transcription:

RESEARCH INVENTY: Internatonal Journal of Engneerng and Scence ISBN: 2319-6483, ISSN: 2278-4721, Vol. 2, Issue 1 (January 2013), PP 25-32 www.researchnventy.com Smulaton of Dstrbuted Power-Flow Controller (Dpfc) Sarmalla Pedakotaah and Santosh A Abstract: Ths paper descrbes the steady-state response and control of power n transmsson lne equpped wth FACTS devces. Detaled smulatons are carred out on two-machne systems to llustrate the control features of these devces and ther nfluence to ncrease power transfer capablty and mprove system relablty. The DPFC s derved from the unfed power-flow controller (UPFC) and DPFC has the same control capablty as the UPFC. The DPFC can be consdered as a UPFC wth an elmnated common dc lnk. The actve power exchange between the shunt and seres converters, whch s through the common dc lnk n the UPFC, s now through the transmsson lnes at the thrd-harmonc frequency. The nteracton between the DPFC, the network and the machnes are analyzed. Keywords: FACTS, DPFC, modellng, power transmsson, AC-DC power converson, semconductor devces, power system control. I. Introducton The flexble ac trans msson system (FACTS) technology s the applcaton of power electroncs n transmsson systems. The man purpose of ths technology s to control and regulate the electrc varables n the power systems. Ths s acheved by usng converters as a controllable nterface between two power system termnals. The resultng converter representatons can be useful for a varety of confguratons. Bascally, the famly of FACTS devces based on voltage source converters (VSCs) conssts of a seres compensator, a shunt compensator, and a shunt/seres compensator. The statc Compensator (STATCOM) s a shunt connected devce that s able to provde reactve power support at a network locaton far away from the generators. Through ths reactve power njecton, the STATCOM can regulate the voltage at the connecton node. The statc synchronous seres compensator (SSSC) s a seres devce whch njects a voltage n seres wth the transmsson lne. Ideally, ths njected voltage s n quadrature wth the lne current, such that the SSSC behaves lke an nductor or a capactor for the purpose of ncreasng or decreasng the overall reactve voltage drop across the lne, and thereby, controllng the transmtted power. In ths operatng mode, the SSSC does not nterchange any real power wth the system n steady-state. The unfed power-flow controller (UPFC) s the most versatle devce of the famly of FACTS devces, snce t s able to control the actve and the reactve power, respectvely, as well as the voltage at the connecton node. The Unfed Power Flow Controller (UPFC) s comprsed of a STATCOM and a SSSC, coupled va a common DC lnk to allow b-drectonal flow of actve power between the seres output termnals of the SSSC and the shunt output termnals of the STATCOM. Each converter can ndependently generate (or) absorb reactve power at ts own AC termnal. The two converters are operated from a DC lnk provded by a DC storage capactor. The UPFC s not wdely appled n practce, due to ther hgh cost and the susceptblty to falures. Generally, the relablty can be mproved by reducng the number of components; however, ths s not possble due to the complex topology of the UPFC. To reduce the falure rate of the components, selectng components wth hgher ratngs than necessary or employng redundancy at the component or system levels. Un fortunately, these solutons ncrease the ntal nvestment necessary, negatng any cost related advantages. Accordngly, new approaches are needed n order to ncrease relablty and reduce cost of the UPFC. The same as the UPFC, the DPFC s able to control all system parameters lke lne mpedance, transmsson angle and bus voltage. The DPFC elmnates the common dc lnk between the shunt and seres converters. The actve power exchange between the shunt and the seres converter s through the transmsson lne at the thrd-harmon c frequency. The seres converter of the DPFC emp loys the dstrbuted FACTS (D- FACTS) concept. Comparng wth the UPFC, the DPFC have two major advantages: 1) Low cost because of the low voltage solaton and the low component ratng of the seres converter and 2) Hgh relablty because of the redundancy of the seres converters and hgh control capablty. DPFC can also be used to mprove the power qualty and system stablty such as power oscllaton dampng, Voltage sag restoraton or balancng asymmetry. 25

II. Dpfc Topology: By ntroducng the two approaches outlned n the prevous secton (elmnaton of the common DC lnk and dstrbuton of the seres converter) nto the UPFC, the DPFC s acheved. Smlar as the UPFC, the DPFC conssts of shunt and seres connected converters. The shunt converter s smlar as a STATCOM, whle the seres converter employs the DSSC concept, whch s to use multple sngle -phase converters nstead of one three-phase converter. Each converter wthn the DPFC s ndependent and has ts own DC capactor to provde the requred DC voltage. The confguraton of the DPFC s shown n Fgure 1. Fgure 1: DPFC confguraton As shown, besdes the key components - shunt and seres converters, a DPFC also requres a hgh pass flter that s shunt connected to the other sde of the transmsson lne and a transformer on each sde of the lne. The reason for these extra components wll be explaned later. The unque control capablty of the UPFC s gven by the back-to-back connecton between the shunt and seres converters, whch allows the actve power to freely exchange. To ensure the DPFC has the same control capablty as the UPFC, a method that allows actve power exchange between converters wth an elmnated DC lnk s requred. III. Dpfc Operatng Prncple Actve Power Exchange Wth Elmnated Dc Lnk Wthn the DPFC, the transmsson lne presents a common connecton between the AC ports of the shunt and the seres converters. Therefore, t s possble to exchange actve power through the AC ports. The method s based on power theory of non-snusodal co mponents. Accordng to the Fourer analyss, nonsnusodal voltage and current can be expressed as the sum of snusodal functons n dfferent frequences wth dfferent ampltudes. The actve power resultng from ths non-snusodal voltage and current s defned as the mean value of the product of voltage and current. Snce the ntegrals of all the cross product of terms wth dfferent frequences are zero, the actve power can be expressed by: P V I cos (1) 1 Where VI and I are the voltage and current at the th harmonc frequency respectvely, and s the correspondng angle between the voltage and current. Equaton (1) shows that the actve powers at dfferent frequences are ndependent from each other and the voltage or current at one frequency has no nfluence on the actve power at other frequences. The ndependence of the actve power at dfferent frequences gves the possblty that a converter wthout a power source can generate actve power at one frequency and absorb ths power from other frequences. By applyng ths method to the DPFC, the shunt converter can absorb actve power from the grd at the fundamental frequency and nject the power back at a harmonc frequency. Ths harmonc actve power flows through a transmsson lne equpped wth seres converters. Accordng to the amount of requred actve powe r at the fundamental frequency, the DPFC seres converters generate a voltage at the harmonc frequency, there by absorbng the actve power from harmonc components. Neglectng losses, the actve power generated at the fundamental frequency s equal to the power absorbed at the harmonc frequency. For a better understandng, Fgure 2 ndcates how the actve power s exchanged between the shunt and the seres converters n the DPFC system. The hgh-pass flter wthn the DPFC blocks the fundamental frequency components and allows the harmonc components to pass, thereby provdng a return path for the harmonc components. The shunt and seres converters, the hgh pass flter and the ground form a closed loop for the harmonc current. 26

IV. Usng Thrd Harmonc Components Fgure 2: Actve power exchange between DPFC converters Due to the unque features of 3rd harmonc frequency components n a three-phase system, the 3rd harmonc s selected for actve power exchange n the DPFC. In a three-phase system, the 3rd harmonc n each phase s dentcal, whch means they are zero -sequence components. Because the zero-sequence harmonc can be naturally blocked by trans- formers and these are wdely ncorporated n power systems (as a means of changng voltage), there s no ext ra flter requred to prevent harmonc leakage. As ntroduced above, a hghpass flter s requred to make a closed loop for the harmonc current and the cut off frequency of ths flter s approxmately the fundamental frequency. Because the voltage solaton s hgh and the harmonc frequency s close to the cut off frequency, the flter wll be costly. By usng the zero-sequence harmonc, the costly flter can be replaced by a cable that connects the neutral pont of the transformer on the rght sde n Fgure 2 wth the ground. Because the -wndng appears open-crcut to the 3rd harmonc current, all harmonc current wll flow through the Y- wndng and concentrate to the groundng cable as shown n Fgure 3. Therefore, the large hgh-pass flter s elmnated. Fgure 3: Utlze grounded transformer to flter zero-sequence harmonc Another advantage of usng the 3rd harmonc to exchange actve power s that the groundng of the transformers can be used to route the harmonc current n a meshed network. If the network requres the harmonc current to flow through a specfc branch, the neutral pont of the the sde opposte to the shunt converter, wll be grounded and vce versa. transformer n that branch, at Fgure 4 shows a smple example of routng the harmonc current by usng the groundng of the transformer. Because the floatng neutral pont s located on the transformer of the lne wthout the seres converter, t s an open-crcut for 3rd harmonc components and therefore no 3rd harmonc current wll flow through ths lne. Fgure 4: Route the harmonc current by usng the groundng of the transformer 27

The harmonc at the frequences lke 3rd, 6th, 9th... are all zero-sequence and all can be used to exchange actve power n the DPFC. However, the 3rd harmonc s selected, because t s the lowest frequency among all zero-sequence harmoncs. The relatonshp between the exchanged actve power at the th harmonc frequency P and the voltages generated by the converters s expressed by the well known the power flow equaton and gven as: V V sh, se, P sn( sh, se, X ) (2) Where X s the lne mpedance at th frequency, and s the voltage magntudes of the harmonc of the shunt and seres converters, and s the angle dfference between the two voltages. As shown, the mpedance of the lne lmts the actve power exchange capacty. To exchange the same amount of actve power, the lne wth hgh mpedance requres hgher voltages. Because the transmsson lne mpedance s mostly nductve and proportonal to frequency, hgh transmsson frequences wll cause hgh mpedance and result n hgh voltage wthn converters. Consequently, the zero -sequence harmonc wth the lowest frequency - the 3rd harmonc - has been selected. V. Dpfc Control To control multple converters, a DPFC conssts of three types of controllers: central control, shunt control and seres control, as shown n Fgure 5. Fgure 5: DPFC control block dagram The shunt and seres control are localzed controllers and are responsble for mantanng ther own converters parameters. The central control takes care of the DPFC functons at the power system level. The functon of each controller s lsted: Central control: The central control generates the reference sgnals for both the shunt and seres converters of the DPFC. Its control functon depends on the specfcs of the DPFC applcaton at the power system level, such as power flow control, low frequency power oscllaton dampng and balancng of asymmetrcal components. Accordng to the system requrements, the central control gves correspondng voltage reference sgnals for the seres converters and reactve current sgnal for the shunt converter. All the reference sgnals ge nerated by the central control concern the fundamental frequency components. Seres control: Each seres converter has ts own seres control. The controller s used to mantan the capactor DC voltage of ts own converter, by usng 3 rd harmonc frequency components, n addton to generatng seres voltage at the fundamental frequency as requred by the central control. Shunt control: The objectve of the shunt control s to nject a constant 3 rd harmonc current nto the lne to supply actve power for the seres converters. At the same tme, t mantans the capactor DC voltage of the shunt converter at a constant value by absorbng actve power from the grd at the fundamental frequency and njectng the requred reactve current at the fundamental frequency nto the grd. VI. Laboratory Results Smulaton Model of the seres converter control 28

RESEARCH INVENTY: Internatonal Journal of Engneerng and Scence ISBN: 2319-6483, ISSN: 2278-4721, Vol. 2, Issue 1 (January 2013), PP 25-32 www.researchnventy.com An expermental setup has been bult to verfy the prncple and control of the DPFC. One shunt converter and sx sngle phase seres converters are bult and tested n a scaled network, as shown n Fg. 7. Two solated buses wth phase dfference are connected by the lne. Wthn the expermental setup, t he shunt converter s a sngle-phase nverter that s connected between the neutral pont of the Y Δ transformer and the ground. The nverter s powered by a constant dc-voltage source. The specfcatons of the DPFC expermental setup are lsted n the Table I. Fg. 7. DPFC expermental setup crcut Table I: Specfcaton Of The Dpfc Expermental Setup Wthn the setup, multple seres converters are controlled by a central controller. The central controller gves the reference voltage sgnals for all seres converters. The voltages and currents wthn the setup are measured by an osclloscope and processed n computer by usng the MATLAB To verfy the DPFC prncple, two stuatons are demonstrated: the DPFC behavour n steady state and the step response. In steady state, the seres converter s controlled to nsert a voltage vector wth both d- and q- component, whch s Vse,d,ref = 0.3 V and Vse,q,ref = 0.1 V. Fgs. 8-10 show one operaton pont of the DPFC setup. For clarty, only the waveforms n one phase are shown. The voltage njected by the seres converter, the current through the lne, and the voltage and current at the Δ sde of the transformer are llustrated. Fg. 8. DPFC operaton n steady state: lne current. Fg. 9. DPFC operaton n steady state: seres converter voltage. 29

Fg. 10. DPFC operaton n steady state: bus voltage and current at the Δ sde of the transformer. The constant thrd-harmonc current njected by the shunt converter evenly dsperses to the three phases and s supermposed on the fundamental current, as shown n Fg. 8. The voltage njected by the seres converter also contans two frequency components n Fg. 9. The ampltude of the pulse wdth modulated (PWM) waveform represents the dc-capactor voltage, whch s well mantaned by the thrd-harmonc component n steady state. As shown, the dc voltage has a small oscllaton; however, t does not nfluence the DPFC control. Fg. 10 demonstrates the thrd-harmonc flterng by the Y Δ transformers. There s no thrdharmonc current or voltage leakng to the Δ sde of the transformer. The DPFC controls the power flow through transmsson lnes by varyng the voltage njected by the seres converter at the fundamental frequency. Fgs. 11-15 llustrate the step response of the expermental setup. A step change of the fundamental reference voltage of the seres converter s made, whch conssts of both actve and reactve varatons, as shown n Fg. 11. As shown, the dc voltage of the seres converter s stablzed before and after the step change. To verfy f the seres converter can nject or absorb actve and reactve power from the grd at the fundamental frequency, the power s calculated from the measured voltage and current n Fgs. 12 and 13. The measured data n one phase are processed n the computer by usng MATLAB. To analyze the voltage and current at the fundamental frequency, the measured data that contans harmonc dstorton are fltered by a low-pass dgtal flter wth the 50-Hz cut off frequency. Because of ths flter, the calculated voltage and current at the fundamental frequency have a 1.5 cycle delay to the actual values, thereby causng a delay of the measured actve and reactve power. Fg. 14 llustrated the actve and reactve power njected by the seres converter. A comparson s made between the measured power and the calculated power. We can see that the seres converters are able to absorb and nject both actve and reactve power to the grd at the fundamental frequency. Fg. 11. Reference voltage for the seres converters. Fg. 12. Step response of the DPFC: seres converter voltage. Fg. 13. Step response of the DPFC: lne current. 30

Fg. 14. Step response of the DPFC: actve and reactvse power njected by the seres converter at the fundamental frequency. Fg. 15. Step response of the DPFC: bus voltage and current at the Δ sde of the transformer. Concluson Ths paper has presented a new concept called DPFC. The DPFC emerges from the UPFC and nherts the control capablty of the UPFC, whch s the smultaneous adjustment of the lne mpedance, the transmsson angle, and the bus-voltage magntude. The common dc lnk between the shunt an d seres converters, whch s used for exchangng actve power n the UPFC, s elmnated. Ths power s now transmtted through the transmsson lne at the thrd-harmonc frequency. The seres converter of the DPFC employs the D-FACTS concept, whch uses multple s mall sngle-phase converters nstead of one large-sze converter. The relablty of the DPFC s greatly ncreased because of the redundancy of the seres converters. The total cost of the DPFC s also much lower than the UPFC, because no hgh -voltage solaton s requred at the seres-converter part and the ratng of the components of s low. The DPFC concept has been verfed by an expermental setup. It s proved that the shunt and seres converters n the DPFC can exchange actve power at the thrd-harmonc frequency, and the seres converters are able to nject controllable actve and reactve power at the fundamental frequency. References [1] Y.-H. Song and A. Johns, Flexble ac Transmsson Systems (FACTS) (IEE Power and Energy Seres), vol. 30. London, U.K.: Insttuton of Electrcal Engneers, 1999. [2] N. G. Hngoran and L. Gyugy, Understandng FACTS: Concepts and Technology of Flexble AC Transmsson Systems. New York: IEEE Press, 2000. [3] L.Gyugy, C.D. Schauder, S. L.Wllams, T. R. Retman,D. R. Torgerson, And A. Edrs, The unfed power flow controller: A new approach to power transmsson control, IEEE Trans. Power Del., vol. 10, no. 2, pp. 1085 1097, Apr. 1995. [4] A.-A. Edrs, Proposed terms and defntons for flexble ac transmsson system (facts), IEEE Trans. Power Del., vol. 12, no. 4, pp. 1848 1853, Oct. 1997. [5] K. K. Sen, Sssc-statc synchronous seres compensator: Theory, modelng, and applcaton, IEEE Trans. Power Del., vol. 13, no. 1, pp. 241 246, Jan. 1998. [6] M. D. Deepak, E. B. Wllam, S. S. Robert, K. Bll, W. G. Randal, T. B. Dale, R. I. Mchael, and S. G. Ian, A dstrbuted statc seres compensator system for realzng actve power flow control on exstng power lnes, IEEE Trans. Power Del., vol. 22, no. 1, pp. 642 649, Jan. 2007. [7] D. Dvan and H. Johal, Dstrbuted facts A new concept for realzng grd power flow control, n Proc. IEEE 36th Power Electron. Spec. Conf. (PESC), 2005, pp. 8 14. [8] Y. Zhhu, S.W. H. de Haan, and B. Ferrera, Utlzng dstrbuted power flow controller (DPFC) for power oscllaton dampng, n Proc. IEEE Power Energy Soc. Gen. Meet. (PES), 2009, pp. 1 5. [9] Y. Zhhu, S. W. H. de Haan, and B. Ferrera, Dpfc control durng shunt converter falure, n Proc. IEEE Energy Convers. Congr. Expo. (ECCE) 2009, pp. 2727 2732. [10] Y. Sozer and D. A. Torrey, Modelng and control of utlty nteractve nverters, IEEE Trans. Power Electron., vol. 24, no. 11, pp. 2475 2483, Nov. 2009. 31

BIOGRAPHY Sarmalla Pedakotaah, II-M.Tech P.E, Department of EEE, SV Engneerng College, Suryapet. Santosh A, M.Tech P.E, Department of EEE, SV Engneerng College, Suryapet. 32