Unit 3 - Wireless Propagation and Cellular Concepts

Similar documents
Unit 4 - Cellular System Design, Capacity, Handoff, and Outage

Unit 8 - Week 7 - Computer simulation of Rayleigh fading, Antenna Diversity

Unit 7 - Week 6 - Wide Sense Stationary Uncorrelated Scattering (WSSUS) Channel Model

Unit 5 - Week 4 - Multipath Fading Environment

12/29/2017 Introduction to Wireless and Cellular Communications - - Unit 2 - Overview of Cellular Evolution and Wireless Technologies

ELEC-E7120 Wireless Systems Weekly Exercise Problems 5

NOISE, INTERFERENCE, & DATA RATES

03_57_104_final.fm Page 97 Tuesday, December 4, :17 PM. Problems Problems

EITN85, FREDRIK TUFVESSON, JOHAN KÅREDAL ELECTRICAL AND INFORMATION TECHNOLOGY. Why do we need UWB channel models?

Level 6 Graduate Diploma in Engineering Wireless and mobile communications

UWB Channel Modeling

WIRELESS COMMUNICATIONS PRELIMINARIES

Chapter 4 Radio Communication Basics

Revision of Lecture One

Written Exam Channel Modeling for Wireless Communications - ETIN10

Revision of Lecture One

MSIT 413: Wireless Technologies Week 3

Performance Evaluation of Uplink Closed Loop Power Control for LTE System

Introduction to Wireless and Mobile Networking. Hung-Yu Wei g National Taiwan University

EC 551 Telecommunication System Engineering. Mohamed Khedr

King Fahd University of Petroleum & Minerals Computer Engineering Dept

Project = An Adventure : Wireless Networks. Lecture 4: More Physical Layer. What is an Antenna? Outline. Page 1

Channel Modeling ETI 085

Selected answers * Problem set 6

Solution: NF=6 db, B=2.1 GHz, SNR min =7dB T=290 k, P in,1db = 10.5 dbm

Noise and Interference Limited Systems

The Friis Transmission Formula

Wireless Physical Layer Concepts: Part II

HY448 Sample Problems

High Speed Data Downlink for NSF Space Weather CubeSats

Direct Link Communication II: Wireless Media. Motivation

ECC Report 276. Thresholds for the coordination of CDMA and LTE broadband systems in the 400 MHz band

FREQUENCY SPECTRUM MANAGEMENT PANEL (FSMP) Fifth Working Group Meeting SUMMARY

EECS 380: Wireless Technologies Week 7-8

Co-existence. DECT/CAT-iq vs. other wireless technologies from a HW perspective

EEG473 Mobile Communications Module 2 : Week # (6) The Cellular Concept System Design Fundamentals

College of Engineering

Direct Link Communication II: Wireless Media. Current Trend

MSIT 413: Wireless Technologies Week 3

Radio Network Planning for Outdoor WLAN-Systems

Adaptive Modulation, Adaptive Coding, and Power Control for Fixed Cellular Broadband Wireless Systems: Some New Insights 1

Antennas and Propagation. Chapter 5

TSEK02: Radio Electronics Lecture 6: Propagation and Noise. Ted Johansson, EKS, ISY

Multiple access and cellular systems

ECE6604 PERSONAL & MOBILE COMMUNICATIONS

3.1. Historical Overview. Citizens` Band Radio Cordless Telephones Improved Mobile Telephone Service (IMTS)

Week 2. Topics in Wireless Systems EE584-F 03 9/9/2003. Copyright 2003 Stevens Institute of Technology - All rights reserved

Spring 2017 MIMO Communication Systems Solution of Homework Assignment #5

TSEK02: Radio Electronics Lecture 6: Propagation and Noise. Ted Johansson, EKS, ISY

Chapter 15: Radio-Wave Propagation

We are IntechOpen, the world s leading publisher of Open Access books Built by scientists, for scientists. International authors and editors

Redline Communications Inc. Combining Fixed and Mobile WiMAX Networks Supporting the Advanced Communication Services of Tomorrow.

Wireless Technology for Aerospace Applications. June 3 rd, 2012

SATELLITE LINK DESIGN

Noise and Propagation mechanisms

Path-loss and Shadowing (Large-scale Fading) PROF. MICHAEL TSAI 2015/03/27

Antennas and Propagation. Chapter 5

We are IntechOpen, the world s leading publisher of Open Access books Built by scientists, for scientists. International authors and editors

Chapter 4 The RF Link

Vehicle Networks. Wireless communication basics. Univ.-Prof. Dr. Thomas Strang, Dipl.-Inform. Matthias Röckl

Satellite Link Budget 6/10/5244-1

Antennas & Propagation. CSG 250 Fall 2007 Rajmohan Rajaraman

Ad hoc and Sensor Networks Chapter 4: Physical layer. Holger Karl

Outline / Wireless Networks and Applications Lecture 3: Physical Layer Signals, Modulation, Multiplexing. Cartoon View 1 A Wave of Energy

Using the epmp Link Budget Tool

CS-435 spring semester Network Technology & Programming Laboratory. Stefanos Papadakis & Manolis Spanakis

Link Budget Calculation

Opportunistic Vehicular Networks by Satellite Links for Safety Applications

Experimental Evaluation Scheme of UWB Antenna Performance

Announcement : Wireless Networks Lecture 3: Physical Layer. A Reminder about Prerequisites. Outline. Page 1

Mobile and Personal Communications. Dr Mike Fitton, Telecommunications Research Lab Toshiba Research Europe Limited

EXAM QUESTION EXAMPLES

Wireless Communication System

Announcements : Wireless Networks Lecture 3: Physical Layer. Bird s Eye View. Outline. Page 1

NATIONAL INSTITUTE OF TECHNOLOGY, Arunachal Pradesh

CS263: Wireless Communications and Sensor Networks

November 24, 2010xx. Introduction

Coexistence Between UWB and Narrowband Cellular Systems

Wireless Transmission in Cellular Networks

REPORT ITU-R M Characteristics of broadband wireless access systems operating in the land mobile service for use in sharing studies

Advanced Antenna Technology

Unit 2: Mobile Communication Systems Lecture 8, 9: Performance Improvement Techniques in Cellular Systems. Today s Lecture: Outline

Exploiting Link Dynamics in LEO-to-Ground Communications

CHAPTER 6 THE WIRELESS CHANNEL

ECS455 Chapter 2 Cellular Systems

Lecture 7/8: UWB Channel. Kommunikations

GTBIT ECE Department Wireless Communication

The Radio Channel. COS 463: Wireless Networks Lecture 14 Kyle Jamieson. [Parts adapted from I. Darwazeh, A. Goldsmith, T. Rappaport, P.

ECE6604 PERSONAL & MOBILE COMMUNICATIONS

UNIVERSITI MALAYSIA PERLIS Pusat Pengajian Kejuruteraan Komputer dan Perhubungan Semester 1, 2011/12 DKT 211 Basic Communication Engineering

Assignment 11: Problems on Multiuser CDMA Networks

Chapter 8 Multiuser Radio Communications

Impact of UWB interference on IEEE a WLAN System

Mobile & Wireless Networking. Lecture 4: Cellular Concepts & Dealing with Mobility. [Reader, Part 3 & 4]

Antennas and Propagation

6 Uplink is from the mobile to the base station.

Assignment 11: Solutions to problems on Multiuser CDMA Networks

Power-control-based Band Allocation in Multiband CDMA

David Tipper. Graduate Telecommunications and Networking Program

Unit-1 The Cellular Concept

Transcription:

X Courses» Introduction to Wireless and Cellular Communications Unit 3 - Wireless Propagation and Cellular Concepts Course outline How to access the portal Assignment 2. Overview of Cellular Evolution and Wireless Technologies Wireless Propagation and Cellular Concepts Lec 5: Basic Cellular Terminology Lec 6: Introduction to Antennas and Propagation Models Lec 7: Link budget, Fading margin, Outage Lec 8: Cellular Concept Lec 9: Cellular system design and analysis This assignment is based on Lectures 5-9 (Unit 3). Covers basic cellular concepts, propagation models, antenna gain, Link budget and cluster design related problems 1) In lecture 5, the uplink and downlink frequency bands of different systems were discussed. For a GSM system, the channel bandwidth is 200 KHz. The downlink frequency is at 955 MHz, then the uplink frequency should be at 820 MHz 910 MHz 935 MHz None of the above 910 MHz 2) An isotropic antenna is radiating at a frequency of 9MHz. What is the free space path loss at a distance of 3 kms from the transmitter antenna? 54 db 54 dbw 61 db 72 db Matlab basics Quiz : Assignment 2 Lec5_notes Lec6_notes Lec7_notes Lec8_notes Lec9_notes Feedback for week 2 61 db 3) Assuming Free space propagation model, If the transmit power is 1000 mw and the received power is 10-9 mw, what is the distance between the transmitter and the receiver. The carrier frequency is 900 MHz. 26.54 km 31.6 km 3.16 km 15.43 km https://onlinecourses.nptel.ac.in/noc17_cs37/unit?unit=14&assessment=22 1/6

Assignment 2 Solutions Cellular System Design, Capacity, Handoff, and Outage Week 4 - Multipath Fading Environment Week 5 - BER Performance in Fading Channels Week 6 - Wide Sense Stationary Uncorrelated Scattering (WSSUS) Channel Model Week 7 - Computer simulation of Rayleigh fading, Antenna Diversity Week 8 - Fading Channels - Diversity and Capacity Week 9 - Capacity and Introduction to CDMA Week 10 - Introduction to CDMA Week 11 - CDMA Receivers 26.54 km 4) Assuming Free Space propagation model, the transmit power is 10 mw and the received power is 10-7 mw. What is the carrier frequency if the distance between the transmitter and the receiver antennas is 3 km? 561.53 MHz 79.62 MHz 8.24 MHz 14.35 MHz 79.62 MHz 5) The received power at the receiver is -95 dbm. The distance between the receiver and transmitter is 4 kms and the wavelength of propagation is 0.5 meters. Assuming the free space propagation model, what is the transmitted signal power? 10 db 10 dbm 5 dbw 5 dbm 5 dbm 6) Consider a transmitter antenna. The output power of the transmitter amplifier is 30 W and the transmit antenna gain is 15 db. The feeder attenuation is 5 db. What is the EIRP (Equivalent Isotropic Radiated Power)? 25 dbw 25 db 55 dbw 55 db Week 12 MATLAB 25 dbw 7) IEEE 802.11a (WLAN standard) uses 64 QAM modulation to achieve a data rate of 54 Mbps. Suppose an / = 38 db is required to achieve the target BER of 10-6. For this data rate, what is the sensitivity of the receiver, if the noise figure = 8 db. -55 dbm -67.3 dbm -80.7 dbw -75.4 dbw -80.7 dbw 8) IEEE 802.11a (WLAN standard) uses 64 QAM modulation to achieve a data rate of 54 Mbps. Suppose an = 38 db is required to achieve the target BER of 10-6 https://onlinecourses.nptel.ac.in/noc17_cs37/unit?unit=14&assessment=22 2/6

. For this data rate, what is the sensitivity of receiver, if receiver has implementation loss of 3 db and noise figure of 8 db. - 53 dbw -47.7 dbm -33.7 dbm -55.3 dbw -47.7 dbm 1. 9) An ultra-wideband (UWB) radio system transmits at a power level of 1 mw using a BW of 1 GHz. Assume that the transmitted power is uniformly spread over the utilized BW and that the UWB transmitter is at a distance of 10 m from a cellular phone. Evaluate if the interference spectral density (Watts/Hz) caused by the UWB transmitter to a cellular phone with NF = 8 db is higher/lower than the Thermal Noise floor (N0). Assume that UWB spectrum overlaps cellular band & isotropic antennas are used & free space propagation model can be applied. Carrier frequency = 1.5 GHz Interference spectral density is stronger than noise spectral density by 20 db Noise spectral density is stronger than Interference spectral density by 20 db Noise spectral density is stronger than Interference spectral density by 30 db Insufficient information to compare the two spectral densities Interference spectral density is stronger than noise spectral density by 20 db 10) Assuming Break-point propagation model, calculate the range over which signal can be transmitted securely when the total pathloss available is 150 db. Carrier frequency is 900 MHz and breakpoint d break = 100 meters. Path loss exponent is n = 3. 30 km 41.3 km 12.7 km 8.8 km 41.3 km 11) In lecture 7, gain of a parabolic antenna was defined. Find the gain of a parabolic antenna with radius 2 meters and efficiency factor ƞ = 0.6. The carrier frequency is 600 MHz. 36.28 dbi 17.39 dbi 22.6 dbi 25.78 dbi 25.78 dbi 12) Consider a cascaded system consisting of three amplifiers blocks at the receiver. The gain and noise figures of the three blocks are described below. G 1 = 10 db G 2 = 10 db G 3 = 60 db F 1 = 3 db F 2 = 10 db F 3 = 10 db https://onlinecourses.nptel.ac.in/noc17_cs37/unit?unit=14&assessment=22 3/6

Find the overall Noise figure F overall of the cascaded system 3 db 3.5 db 4.76 db 5.3 db 4.76 db 13) Let's say two towers A and B are "d" meter apart with tower A transmitting twice as much power as B. There is a user connected to tower A moving towards tower B. Find the distance from Tower A when the user observes 0 db Signal to Interference ratio. Consider free space propagation i.e the path loss exponent = 2. 0.585 d 0.24 d 0.75 d 0.12 d 0.585 d 14) In a city, cell planning is done with clusters of size 4. There are 100 channels available per cell. Each cluster covers 4 sq.km area. If the city spans over 100 sq.km then calculate the capacity of the designed cellular system. 5000 10000 1000 12000 10000 15) For questions 15 to 20 use the information described below. Consider a cellular network built with 7-cell clusters, as described in Lecture No. 9 / starting from Slide 3. There is no interference across cells within a cluster, as two cells in a cluster do not share the same channel. However, there is interference from neighbouring clusters that use the same set of carrier frequencies but in a fashion that minimizes the maximum interference between two cells that use the same frequency (Cochannel cells). Assume that the Base Station transmits at 1W power and a Free-Space-Path-loss model, 4 π d 2 ( λ ), R = 1km and Carrier frequency = 2.4 MHz(for the channel of interest) Do not approximate unless stated otherwise, for Q15-20. What is the co-channel reuse ratio for the cellular network. 5.29 4.58 4.24 3.14 https://onlinecourses.nptel.ac.in/noc17_cs37/unit?unit=14&assessment=22 4/6

4.58 16) Calculate the worst-case SINR due to only Tier-1 interferers, without any approximations. Hint: Use a slightly different (u,v) coordinate system from the one described in class. 5.44 db 5.67 db Insufficient information 17) What is the worst-case SINR due to only Tier-2 interferers? Choose the closest value among the given options. (Hint: Approximate. Calculate distances from the center of the cells ) 3.01 db 7.2 db 7.78 db 8.45 db 7.78 db 18) What will be the worst-case Tier-1 SINR if the path loss exponent increases to 4. Again, choose the closest answer. 17.82 db 18.7 db 20.17 db Insufficient Information 17.82 db 19) Assume that a thermal noise (AWGN) of -54 dbm is added to the signal at the receiver(ue). What will be the Signal-to-Noise(interference+AWGN) of the user, considering only Tier-1 interferers with path loss exponent = 2. 7.62 db 4.17 db None of these 20) (19 contd. ) How will the SNR change for the above scenario, if the path loss exponent changes to 4. https://onlinecourses.nptel.ac.in/noc17_cs37/unit?unit=14&assessment=22 5/6

SNR increases to 17.82 db SNR decreases to 3.72 db SNR remains the same None of the above SNR decreases to 3.72 db https://onlinecourses.nptel.ac.in/noc17_cs37/unit?unit=14&assessment=22 6/6