Applications LTE handsets, data cards & mobile routers Band 7 2500-2570 MHz Uplink 2620-2690 MHz Downlink 8 Pin 1.6 x 2.0 mm Package Product Features Highly Selective LowDrift BAW Duplexer Low Insertion Loss Over Full Bandwidth and Operating Conditions High Isolation WiFi Co-existence Single-Ended (SE) 50ohm Receive & Transmit Ports Performance -20 to +85 ºC RoHS Compliant, Pb-Free Module Package Functional Block Diagram Antenna 7 6 5 8 4 1 2 3 Receive Transmit Top View General Description The is a high-performance Bulk Acoustic Wave (BAW) duplexer designed to meet the strict LTE requirements for use in Band 7 applications. is specifically designed to meet the high performance expectations of insertion loss, isolation and linearity for LTE systems over the bandwidth of B7 applications under all operating conditions. Due to the exceptional WLAN rejection performance, WiFi coexistence is enabled with this duplexer. Pin Configuration Pin # Label 1 Receive 3 Transmit 6 Antenna 2, 4, 5, 7, 8 (Ground*) Backside Center Pad (Ground*) *See application section for details on optimal grounding. The uses common module packaging techniques to achieve the industry standard 2.0 x 1.6 x 0.9 mm footprint. The duplexer exhibits excellent power handling capabilities. Ordering Information Part No. -EVB Description B7 BAW Duplexer Evaluation Board Standard T/R size = 10000 pieces on a 7 reel. Preliminary Datasheet: Rev. D 12-01-14-1 of 9 - Disclaimer: Subject to change without notice
Absolute Maximum Ratings Parameter Storage Temperature RF Input Power (CW, 50Ω,T = 25 C) Rating 40 to +85 C +29 dbm Operation of this device outside the parameter ranges given above may cause permanent damage. Recommended Operating Conditions Parameter Min Typ Max Units TCASE 20 +85 C The duplexer will function over the recommended range without degradation in reliability or permanent change in performance. Electrical Specifications (1) Antenna Transmit 20 C +25 C +85 C Parameter Conditions Min Max Min Typ Max Min Max Units Insertion Loss 2500-2570 MHz 3.3 2.5 2.8 3.2 db VSWR Attenuation 2nd Harmonics (2) 2500-2570 MHz (Ant Port) 2.1:1 1.8:1 2.0:1 2.1:1-2500-2570 MHz (Tx Port) 2.0:1 1.6:1 2:1 2:1-10 1565.42 MHz 30 37 30 1565.4 1585.4 MHz 40 45 40 1597.5 1605.9 MHz 40 44 40 1606 1680 MHz 37 41 37 1805 1880 MHz 30 36 30 1900 1920 MHz 30 35 30 2010 2025 MHz 30 34 30 2110 2170 MHz 30 35 30 db 2400 2460 MHz 36 39 36 2460 2474 MHz 28 30 28 2474 2480 MHz 26 28 18 2620 2690 MHz 45 49 45 5000 5140 MHz 25 34 25 5150 5850 MHz 20 27 20 5000 5140 MHz at 27.5 dbm, input modulation is LTE 5 MHz BW 25RB (signal source) and measurement RBW 1 MHz 33 dbm Preliminary Datasheet: Rev. D 12-01-14-2 of 9 - Disclaimer: Subject to change without notice
Electrical Specifications (1) Antenna Receive 20 C +25 C +85 C Parameter Conditions Min Max Min Typ Max Min Max Units Insertion Loss 2620 2690 MHz 2.7 1.9 2.5 2.5 db VSWR Attenuation 2620 2690 MHz (Ant Port) 2.5:1 1.7:1 2.0:1 2.0:1-2620 2690 MHz (Rx Port) 2.2:1 1.6:1 2.0:1 2.0:1-1 2380 MHz 18 35 18 2380 2450 MHz 33 35 33 2450 2484 MHz 45 49 45 2500 2570 MHz 48 52.5 48 db 2775 4000 MHz 32 57 32 4000 4500 MHz 27 36 27 4500 6000 MHz 40 45 40 Electrical Specifications (1) Transmit Receive 20 C +25 C +85 C Parameter Conditions Min Max Min Typ Max Min Max Units Isolation (3) 2500 2570 MHz 52 54 52 2620 2690 MHz 50 52 50 db Notes: 1. All specifications are based on the TriQuint schematic for the main reference design. 2. Additional 2 nd harmonic improvement can be achieved using appropriate application. Refer to product technical notes for details. 3. Integrated over a 10 MHz channel. Preliminary Datasheet: Rev. D 12-01-14-3 of 9 - Disclaimer: Subject to change without notice
-EVB Evaluation Board PC Board PCB routing detail Notes: 1. Top, middle & bottom layers: 1 oz copper. 2. Substrates: Rogers 4350B dielectric, 0.062 thick. 3. Finish plating: Nickel: 3-8µm thick, Gold:.03-.2µm thick. 4. Hole plating: Copper min.0008µm thick. Notes: 1. Light grey indicates metalized area. 2. Dark grey indicates pad areas. 3. This footprint represents a recommendation only. 4. For solder pad recommendation see mechanical information. 1 Rx ANT L 1 = 2.2 nh 6 L 2 = 3.3 nh C 1 =0.5 pf 2, 4,5,7, 8,9 3 L 3 = 1. 6 nh Tx Bill of Material -EVB Reference Des. Value Description Manuf. Part Number U1 N/A B7 BAW Duplexer TriQuint C1 0.5 pf Chip Capacitor, 0201, ± 5% Murata GRM0335C0G0R5C25Z500 L1 2.2 nh Chip Inductor, 0201, ± 0.1nH Murata LQP03TN2N2B02 L2 3.3 nh Chip Inductor, 0201, ± 0.1nH Murata LQP03TN3N3B02 L3 1.6 nh Chip Inductor, 0201, ± 0.1nH Murata LQP03TN1N6B02 PCB N/A 4-layer Preliminary Datasheet: Rev. D 12-01-14-4 of 9 - Disclaimer: Subject to change without notice
Receive Performance Plots -EVB Temp=25 C Preliminary Datasheet: Rev. D 12-01-14-5 of 9 - Disclaimer: Subject to change without notice
Transmit Performance Plots -EVB Temp=25 C Preliminary Datasheet: Rev. D 12-01-14-6 of 9 - Disclaimer: Subject to change without notice
Isolation/Antenna Return Loss -EVB Temp=25 C Preliminary Datasheet: Rev. D 12-01-14-7 of 9 - Disclaimer: Subject to change without notice
Mechanical Information Package Marking and Dimensions Marking: Part number 6027 Lot Code XXXX 0.10 0.430 2.05 (2.10 MAX) 1.85 0.430 (5) (6) (7) 0.30 1.45 0.275 0.275 (4) (3) Center Pad (9) (8) 0.60 (2) (1) 0.15 1.65 (1.70 MAX) 0.33 0.18 0.15 x 45 o 0.33 0.90 (0.92 MAX) ANT 2.05 (2.10 MAX) ANT 6027 RX XXXX TX 1.65 (1.70 MAX) Side View Pin 1 Mark & Product Designation Top View NOTES: 1. All dimensions are in millimeters. Angles are in degrees. 2. Except where noted, this part outline conforms to JEDEC standard MO-220, Issue E (Variation VGGC) for thermally enhanced plastic very thin fine pitch quad flat no lead package (QFN). 3. Dimension and tolerance formats conform to ASME Y14.4M-1994. 4. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012. Tape and Reel Information Standard T/R size = 10,000 units/reel. All dimensions are in millimeters Preliminary Datasheet: Rev. D 12-01-14-8 of 9 - Disclaimer: Subject to change without notice
Product Compliance Information ESD Sensitivity Ratings Caution! ESD-Sensitive Device Solderability Compatible with both lead-free (260 C max. reflow temperature) and tin/lead (245 C max. reflow temperature) soldering processes. Contact plating: Electrolytic plated Au over Ni ESD Rating: Class 1A Value: 250 V to < 500 V Test: Human Body Model (HBM) Standard: ESDA/JEDEC Standard JS-001-2012 ESD Rating: Class C3 Value: 1000 V Test: Charged Device Model (CDM) Standard: JEDEC Standard JESD22-C101F MSL Rating MSL Rating: Level 3 Test: 260 C convection reflow Standard: JEDEC Standard IPC/JEDEC J-STD-020 RoHs Compliance This part is compliant with EU 2002/95/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment). This product also has the following attributes: Lead Free Halogen Free (Chlorine, Bromine) Antimony Free TBBP-A (C15H12Br402) Free PFOS Free Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint: Web: www.triquint.com Tel: +1.407.886.8860 Email: info-sales@triquint.com Fax: +1.407.886.7061 For technical questions and application information: Email: fl.product.engineering@triquint.com Important Notice The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information contained herein. TriQuint assumes no responsibility or liability whatsoever for any of the information contained herein. TriQuint assumes no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. TriQuint products are not warranted or authorized for use as critical components in medical, life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Preliminary Datasheet: Rev. D 12-01-14-9 of 9 - Disclaimer: Subject to change without notice