REMOTE RECEIVER DIMENSION : L = 90 MM X H = 75 X D = 38 MM. R F RANGE FOR TRANSMITTER AND RECEIVER IS 20 TO 30 METERS IN CLOSED AREA R F SIGNAL CROSSED WOODEN, R C C WALL, GLASS, AND METAL DOORS REMOTE RECEIVER INSTALLATION = INSTALL REMOTE RECEIVER IN WOODEN CABINET, PLASTIC CASING OR FALSE CEILING AREA DON T KEEP IN METAL CASING.
ARRANGE 230 V A C SUPPLY FOR 12 V S M P S POWER SUPPLY. POWER SUPPLY FOR RECEIVER = 12 VOLT DC 2 AMP FOR LOCK DRIVE ONLY. OUT PUT = 12V DC OUT WITH DRY CONTACT OUTPUT COM, NC, NO. ARRANGE 14/36 GAUGE 4 CORE FLEXIBLE WIRE FOR REMOTE RECEIVER TO LOCK 2 CORE WIRE FOR LOCK AND OTHER 2 CORE WIRE FOR BUZZER OR LED INDICATION. SYSTEM MODE = ON, OFF OR DELAY WHICH IS CHANGEABLE BY JUMPER SETTING. DELAY TIME = 2.5 SEC, 5 SEC, 7.5 SEC, AND 10 SEC.SECONDS CAN BE SET BY JUMPER SETTING. DELAY MODE = ALL 4 BUTTON A, B, C & D WILL WORK WITH DELAY MODE. ON OFF MODE = REMOTE TRANSMITTER HAVING 4 SWITCHES A, B, C & D. A OR B FOR LOCK TURN TO ON AND C OR D FOR LOCK TURN TO OFF. PANIC ALARM = SAME FOR DC 12V OPERATED HOOTER OR SIREN MANUAL OPERATION = RECEIVER IS WORKING WITH CONNECTING PUSH TO ON SWITCH FOR DELAY AND ON OFF MODE ( GRAY AND WHITE WIRE ) THIS REMOTE RECEIVER WILL WORK WITH ANY ACCESS CONTROL SYSTEMS FOR OUT SIDE ENTRY ACCESS CONTROL WILL WORK AND FOR INSIDE REMOTE CONTROL WILL WORK GENERALLY WHEN WE USE ACCESS CONTROL, LOCK IS ALREADY CONNECTED WITH ACCESS CONTROL AFTER THAT WE ONLY HAVE TO CONNECT DRY CONTACT WIRE GREEN AND BLUE PARALLEL TO ACCESS CONTRAL EXIT SWITCH WIRE AT THAT TIME DELAY TIME MUST SET 2.5 SECONDS.
IN THIS REMOTE RECEIVER WE CAN PROGRAMME MAXIMUM 8 TRANSMITTER REMOTE TRANSMITTER PROGRAMMING PROCEDURE 1 ALL 1 TO 8 TRANSMITTER WILL BE KEPT READY FOR PROGRAMMING. 2 TURN REMOTE RECEIVER POWER ON. 3 PRESS PROGRAMME SW 5 SECOND. 4 YELLOW LED WILLBLINK ON AND OFF. 5 WITH IN 3 SECONDS PRESS REMOTE TRANSMITTER A BUTTON FOR 2 SECONDS YELLOW LED WILL BLINK ON AND OFF THEN RELEASE A BUTTON. THIS PROCEDURE WILL REPEAT 8 TIMES, AFTER 8 TIMES PRESS AND RELEASE TRANSMITTER A BUTTON, BOTH BLUE AND YELLOW LED WILL BLINK ON AND OFF THAT MEANS ALL 1 TO 8 TRANSMITTER PROGRAMMED SUCCESSFULLY. 6 FOR EXAMPLE : IF PROGRAMME 2 TRANSMITTER 7 PRESS PROGRAMME SW 5 SECOND. 8 BLUE LED WILL BLINK ON AND OFF 9 WITH IN 3 SECOND PRESS 1 ST REMOTE TRANSMITTER A BUTTON FOR 2 SECOND YELLOW LED WILL GO ON AND OFF RELEASE A BUTTON, AGAIN PRESS 1 ST TRANSMITTER A BUTTON FOR 2 SECONDS AGAIN YELLOW LED WILL GO ON AND OFF THIS PROCEDURE FOR 1 ST REMOTE TRANSMITTER 4 TIME AND ANOTHER 4 TIME FOR 2 ND TRANSMITTER TO
COMPLETE REMOTE TRANSMITTER PROGRAMMING BOTH YELLOW AND BLUE LED WILL BLINK ON AND OFF. 10 IF 3 TRANSMITTER PROGRAMMING. 11 1 ST TRANSMITTER A, A, BUTTON PRESS, 2 ND TRANSMITTER A, A, 3 RD TRANSMITTER A, A, AGAIN 1 ST TRANSMITTER A, A BUTTON PRESS BOTH BLUE AND YELLOW LED WILL GO ON AND OFF. 12 IF 4 TRANSMITTER PROGRAMMING 13 1 ST TRANSMITTER A, A BUTTON PRESS, 2 ND TRANSMITTER A, A, 3 RD TRANSMITTER A, A, AND 4 TH TRANSMITTER A A BUTTEN PRESS, BOTH YELLOW AND BLUE LED WILL GO ON AND OFF.THAT MEANS ALL 4 TRANSMITTER IS PROGRAMMED SUCCESSFULLY. WIRING CONNECTION FOR REMOTE RECEIVER 1.BLACK WIRE : TO 0 VOLT SMPS POWER SUPPLY 2.BROWN WIRE : TO 12 VOLT DC + SMPS POWER SUPPLY 3. RED WIRE : +12 VOLT DC OUT FOR YALE TYPE DOOR STRIKE 4. ORANGE WIRE : 0 VOLT FOR DORR STRIKE, E M LOCK OR DROP BOLT 5. YELLOW WIRE : +12 VOLT OUT FOR E M LOCK OR DROP BOLT LOCK 6.GREEN WIRE : N O DRY CONTACT OUT PUT 7.BLUE WIRE : COM DRY CONTACT OUT PUT 8.VIOLET WIRE : N C DRY CONTACT OUT PUT 9.GRAY WIRE : PUSH TO ON SWITCH ( DRY CONTACT ) 10.WHITE WIRE : PUSH TO ON SWITCH ( DRY CONTACT )
REMOTE RECEIVER WITH ACCESS CONTROL WIRING CONNECTION WITH LOCK. LOCK CONNECD WITH ACCESS CONTROL. REMOTE RECEIVER WIRING CONNECTION WITH LOCK EXIT SW AND S M P S REMOTE RECEIVER WITH ACCESS CONTROL WIRING CONNECTION WITH LOCK. LOCK CONNECTED WITH REMOTE RECEIVER.