TP00 OWNER S MANUAL INCH THICKNESS PLANER For Your Safety: Read all instructions carefully Save this manual for future reference SP PrintedinTaiwan
Parts List for " Thickness Planer Model. TP00 Figure Always order by Part Number - t by Number.. 0-0 0 0 - - - Cord w/plug * Screw Pan Hd M x 0.- Housing Switch Gasket Foam Motor (Includes Brushes) Holder Brush Brush Cap Brush *ScrewHexSocSet M x 0.- Label D RIDGID * Lockwasher M Lead Ground * Standard Hardware Item - May be purchased locally. These replacement parts are available where you purchased your Planer. - 0 0 0 AC00 - *ScrewPanHdTy TT M x 0.- Rod Motor Pivot Switch Reset (Includes Nut) Bezel Switch Switch Locking Switch Screw Special Clamp Cord * Washer. x x *ScrewPanHd.Mx0.-0 Guard Cord
Parts List for " Thickness Planer Model. TP00 Figure 0 0 0 0 0 0
Parts List for " Thickness Planer Model. TP00 Figure Always order by Part Number - t by Number 0 0 0- - - - - - - 0 0 0-0 - AC0 Scr Hex Soc Butt Hd M x.0- Cap Left Scale Length Cover Upper Cap Right Pad Upper Ring Retaining C Worm Gear L.H. Plate Lock Left * Scr Hex Soc Cap M x 0.- Sleeve Plate Lock Right Shaft Transmission Washer. x x NutLockMx.0 Support * Washer x x * Scr Soc Set Cup Pt M x 0.- Worm Elevation Handle Knob Snipe * Scr Hex Soc Cap M x 0.- Chute Dust Knob Chute Cover Shroud *ScrPanHdMx0.- * Washer. x x 0. Manifold Air Gasket Rear Gasket Right Gasket Left Cover Worm Gear R.H. Bushing Screw Elevating R.H. *ScrPanHdMx0.- Plate Dust Chute Clamp Cord Spring /Plunger Frame Upper Block Support Lock Cutter Head Spacer Cutter Head Lock *ScrPanHdMx0.- Knife Planer 0 * Standard Hardware Item - May be purchased locally. These replacement parts are available where you purchased your Planer. 0 0 0 - - - 0 - - - 0-0 - - - - - - 0-0 - - SP Bar Knife Lock Screw Knife Lock * xmm Collar Knife * Scr Hex Soc Cap M x 0.- Pulley Cutter head Belt Drive Nut Hex M x.0 L.H. Pulley Motor Retainer Bearing Bearing Ball ZZ Head Cutter (Includes Collar knife, Retainer Bearing, Bearing Ball and Gear Pinion) Pin Spring x mm * Screw Hex Hd M x 0.- *NutHexMx0. Rod Step Nut Special M x. Indicator Depth Scr Pan Hd M x 0.- Rod Pointer Elevating Spring Coil.XX0. Cover Pointer Scr Pan Cr M x 0.- Housing Pointer Pointer Nut Lockwasher Ext Tooth M Scr Pan Hd TY TT M x 0.- Gear Pinion Gear Box Asm * Scr Hex Soc Cap M x 0.- * Scr Hex Soc Cap M x 0.-0 Spacer x x Sprocket Chain Ring Retaining Ext STW Lockwasher M Scr Hex Soc Hd Lock M Scr Hex Soc Hd Lock Mx0.- Lockwasher M Scr Soc Set Cup Pt M x 0.- Bushing. x x Owners Manual
Parts List for " Thickness Planer Model. TP00 Figure 0 0 0 SeeFigure 0
0-0 - 0-0 - - - * Standard Hardware Item - May be purchased locally. Parts List for " Thickness Planer Model. TP00 Figure Always order by Part Number - t by Number Ring Retaining Sprocket Chain Spring Coil Left Block Bearing Plate Retainer Left Roller Outfeed Spring Coil Right Plate Retainer Right * Scr Hex Soc Cap M x 0.- Roller Infeed * Washer. x x Worm Gear L.H. Screw Elevating L.H. Rail Guide Plate Wear Table Rear Case Knife (Knives not included) * Washer M x x *ScrewHexHdMx.- *ScrPanHdTy TT Mx0.- Plate Stiffener Spring Torsion PlateSideGuard Cover Side Right Hub Handwheel Knob Handwheel * Scr Hex Soc Cap M x 0.- * Lockwasher M Screw Hex Soc.Fl Hd M x.0-0 0 0 0-00 0 - - - 0 - - - - Cover Side RH Scale Thickness Spring Coil.x.x0. Ball Steel Block Guard Block Step Knob Step Pin Step Block * Nut Hex M x.0 * Scr Pan Hd M x 0.- Spring Flat Base Bolt Adjustment Nut Hex Special M x. Pad Base * Scr Hex M x.0- Table Front * Nut Hex M x. NutLockMx. Rod Support *ScrPanHdTy TT Mx0.- Cover Side Left Holder Tool Tool Knife * Wrench Hex L mm Wrench Box M & M Cover Tool Box Scr Hex Soc Cap Mx0.- Rod Pivot Repair Parts
Wiring Diagram Black Switch Motor Lead White Over Load Motor Lead Motor Power Cord Green Grounding Wire Troubleshooting Problem Possible Cause Remedy Snipe (Gouging at ends of board) Fuzzy Grain Torn Grain Rough Raised Grain Uneven Depth Cut Side to Side Cutter head Elevation Adjusts with Difficulty Board Thickness Does t Match Depth of Cut Scale Chain Jumping Motor does not start Dust chute is blocked. Dull knives. Inadequate support of long boards. Lumber not butted properly. Extensions misaligned. Planing wood with a high moisture content. Too heavy a cut. Knives cutting against grain. Dull knives. Dull knives. Too heavy a cut. Moisture content too high. Replace knives per instructions (See Replacing Knives section). Support long boards. Butt end to end each piece of stock as boards pass through planer. Adjust extension supports. Remove high moisture content from wood by drying. Review Depth of Cut section. Review Feeding the Work section. Replace knives per instructions. Replace knives per instructions. Review Depth of Cut. Dry the wood or use dried wood. Blade projection not uniform. Check that end of knife is fully seated in the cutter head.. Elevation screws dirty.gearsorscrewsworn. Friction between casing and covers. Indicator not set correctly. Knife projection incorrect. Sprockets worn. Chain worn. Switch malfunction. Overload protector tripped. Supply fuse opens. Brushes worn. Other. Build up of resin under dust chute. Large debris. Clean and lubricate elevation screws. Replace. Clean, lubricate. Adjust indicator/securely tighten. Set knife projection correctly (See Replacing Knives section).. Replace sprockets. Replace chain. Have a qualified electrician replace the ON/ OFF switch.. Turn power switch off. When planer temperature adequately cools (allow -0 minutes) press overload protector reset button.. Replace fuse with a amp time delay fuse, or circuit breaker.. See Maintenance section, Changing Brushes. Get authorized service.. Clean dust chute and exhaust area.. Clear debris.