Optocoupler, Low Input Current, Phototransistor Output FEATURES Temperature range - 55 C to + 11 C Rated impulse voltage (transient overvoltage) V IOTM = 6 kv peak Isolation test voltage (partial discharge test voltage) V pd = 1.6 kv Rated isolation voltage (RMS includes DC) V IOWM = 6 V RMS Rated recurring peak voltage (repetitive) V IORM = 85 V peak Thickness through insulation.4 mm Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 A C 1 4 2 3 E C 17918_1 DESCRIPTION The consists of a phototransistor optically coupled to a gallium arsenide infrared-emitting diode in a 4 pin plastic dual inline package. AGENCY APPROVALS (All parts are certified under base model ) BSI: EN 665:22, EN 695:2 DIN EN 6747-5-5, available with option 1 FIMKO EN 665, EN 6335-1, EN 695-1 UL file no. E52744 cul tested to CSA 22.2 bulletin 5A CQC GB4943.1-211, GB8898-211 APPLICATIONS Circuits for safe protective separation against electrical shock according to safety class II (reinforced isolation): for appl. class I - IV at mains voltage 3 V for appl. class I - IV at mains voltage 6 V according to table 1 of IEC 6664-1, suitable for: - Switch-mode power supplies - Line receiver - Computer peripheral interface - Microprocessor system interface ORDERING INFORMATION V O 6 1 A - # X # # T DIP-# PART NUMBER CTR BIN PACKAGE OPTION TAPE AND REEL 7.62 mm Option 6 Option 7 1.16 mm >.6 mm Option 8 Option 9 AGENCY CERTIFIED/PACKAGE CTR (%) BSI, FIMKO, UL, cul 4 to 8 63 to 125 1 to 2 16 to 32 DIP-4-1 -2-3 - SMD-4, option 7 - - -3X7T - SMD-4, option 8 - - -3X8T -4X8T SMD-4, option 9 - - -3X9T - VDE, BSI, FIMKO, UL, cul 4 to 8 63 to 125 1 to 2 16 to 32 DIP-4 - - -3X1 - DIP-4, 4 mil, option 6 - - -3X16 - SMD-4, option 7 - - - -4X17T SMD-4, option 8 - - -3X18T - SMD-4, option 9-1X19T - -3X19T -4X19T Note Additional options may be possible, please contact sales office Rev. 1.7, 18-Feb-13 1 Document Number: 81775 9.27 mm > 8 mm
ABSOLUTE MAXIMUM RATINGS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage V R 6 V Forward current I F 6 ma Forward surge current t p 1 μs I FSM 1.5 A LED power dissipation at 25 C P diss 1 mw OUTPUT Collector emitter voltage V CEO 7 V Emitter collector voltage V ECO 7 V Collector current I C 5 ma Collector peak current t p /T =.5, t p 1 ms I CM 1 ma Output power dissipation at 25 C P diss 15 mw COUPLER Isolation test voltage (RMS) t = 1 min V ISO 5 V RMS Operating ambient temperature range T amb - 55 to + 11 C Storage temperature range T stg - 55 to + 125 C Soldering temperature (1) 2 mm from case, 1 s T sld 26 C Notes Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted parts (SMD), and wave profile for soldering conditions for through hole parts (DIP), please go to Assembly Instructions (www.vishay.com/doc?854). ELECTRICAL CHARACTERISTICS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage I F = 5 ma V F 1.25 1.6 V Reverse current V R = 6 V I R 1 μa Junction capacitance V R =, f = 1 MHz C j 5 pf OUTPUT Collector emitter voltage I C = 1 ma V CEO 7 V Emitter collector voltage I E = 1 μa V ECO 7 V Collector emitter cut-off current V CE = 2 V, I F = A I CEO 1 1 na COUPLER Collector emitter saturation voltage I F = 1 ma, I C = 1 ma V CEsat.3 V Cut-off frequency V CE = 5 V, I F = 1 ma, R L = 1 f c 11 khz Coupling capacitance f = 1 MHz C k.6 pf Note Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Rev. 1.7, 18-Feb-13 2 Document Number: 81775
CURRENT TRANSFER RATIO (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT -1 CTR 13 3 % V CE = 5 V, I F = 1 ma -2 CTR 22 45 % -3 CTR 34 7 % I C /I F -4 CTR 56 9 % -1 CTR 4 8 % V CE = 5 V, I F = 1 ma -2 CTR 63 125 % -3 CTR 1 2 % -4 CTR 16 32 % SAFETY AND INSULATION RATED PARAMETERS PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Partial discharge test voltage - routine test 1 %, t test = 1 s V pd 1.6 kv Partial discharge test voltage - lot test (sample test) t Tr = 6 s, t test = 1 s, (see figure 2) V pd 1.3 kv V IO = 5 V R IO 1 12 Insulation resistance V IO = 5 V, T amb = 1 C R IO 1 11 V IO = 5 V, T amb = 15 C (construction test only) R IO 1 9 Rated impulse voltage V IOTM 6 kv Max. working voltages Recurring peak voltage V IORM 85 V peak Forward current I SI 13 ma Power dissipation P SO 265 mw Safety temperature T si 15 C Creepage distance 7.6 mm Note According to DIN EN 6747-5-5 (VDE 884), 7.4.3.8.2 (see figure 2). This optocoupler is suitable for safe electrical isolation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits. 3 25 2 Phototransistor P so (mw) V IOTM t 1, t 2 = 1 s to 1 s t 3, t 4 = 1 s t test = 1 s t stres = 12 s 15 1 V pd V IOWM V IORM 5 IR-diode I si (ma) 94 9182-2 25 5 75 1 125 T si - Safety Temperature ( C) 15 1393 t 1 t Tr = 6 s t 3 t test t 4 t 2 t stres t Fig. 1 - Derating Diagram Fig. 2 - Test Pulse Diagram for Sample Test according to DIN EN 6747-5-5 (VDE884), IEC 6747 Rev. 1.7, 18-Feb-13 3 Document Number: 81775
SWITCHING CHARACTERISTICS (T amb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Delay time Rise time Fall time Storage time Turn-on time Turn-off time Turn-on time Turn-off time V S = 5 V, I C = 2 ma, R L = 1, V S = 5 V, I C = 2 ma, R L = 1, V S = 5 V, I C = 2 ma, R L = 1, V S = 5 V, I C = 2 ma, R L = 1, V S = 5 V, I C = 2 ma, R L = 1, V S = 5 V, I C = 2 ma, R L = 1, V S = 5 V, I F = 1 ma, R L = 1 k, (see figure 4) V S = 5 V, I F = 1 ma, R L = 1 k, (see figure 4) t d 3 μs t r 3 μs t f 4.7 μs t s.3 μs t on 6 μs t off 5 μs t on 9 μs t off 1 μs I F I F I F + 5 V IC = 2 ma; adjusted through input amplitude I C 1 % 9 % t p t R G = 5 Ω t p T =.1 t p = 5 µs 95 184 5 Ω 1 Ω Channel I Channel II Oscilloscope R L = 1 MΩ C L = 2 pf 1 % t p t d t r t on (= t d + t r ) t r t d t on Pulse duration Delay time Rise time Turn-on time t s t f t off t s t f t off (= t s + t f ) t Storage time Fall time Turn-off time 96 11698 Fig. 3 - Test Circuit, Non-Saturated Operation Fig. 5 - Switching Times I F I F = 1 ma + 5 V I C R G = 5 Ω t p T =.1 t p = 5 µs 5 Ω 1 kω Channel I Channel II Oscilloscope R L 1 MΩ C L 2 pf 95 1843 Fig. 4 - Test Circuit, Saturated Operation Rev. 1.7, 18-Feb-13 4 Document Number: 81775
PACKAGE DIMENSIONS in millimeters 6.5 ±.3 Pin 1 identifier 4.58 ±.3 7.62 to 9.5.4 ±.1 3.5 ±.3 4.5 ±.3 1.3 ±.1 to 15 2.8 ±.5.5 ±.1.25 typ. i17827-11 2.54 typ. Option 6 Option 7 Option 8 Option 9 1.3 max. 2.7 min. 3.5 ±.3.1 min..6 min. 8 min. 4.3 ±.3.6 min..25 ±.1 3.5 ±.3 9.27 min..1 ±.1 3.6 ±.3 1.3 max. 12.1 max..6 min. 8 min. 1.16 typ. 282-38 2.54 1.52 8 min. 11.5 R.25 1.78.76 2.54 1.52 9.95 min. 13. R.25 1.78.76 2.54 1.52 7.7 11.5 R.25 1.78.76 PACKAGE MARKING (Example of VO617A-3X18T) -3 Note Only options 1, 7, and 8 are reflected in the package marking. The VDE logo is only printed on option 1 parts. Tape and reel suffix (T) is not part of the package marking. V YWW 24 Rev. 1.7, 18-Feb-13 5 Document Number: 81775
PACKING INFORMATION DEVICE PER TUBE TYPE UNITS/TUBE TUBES/BOX UNITS/BOX DIP-4, standard and option 6 1 4 4 Top cover tape 17998 Embossed carrier Fig. 6 - Tape and Reel Shipping Medium Embossment 1 pitch cumulative tolerance on tape ±.2.35 ±.1 2 ±.1 4 ±.1 1.55 +.1 1.75 ±.1 7.5 ±.1 4.65 ±.1 16 ±.3 5 max. 5 max. X X 12 ±.1 1.5 ±.1 4.55 ±.1 1.3 ±.1 Section X-X Fig. 7 - Tape and Reel Packing for Option 7 and Option 9 (1 units per reel) Rev. 1.7, 18-Feb-13 6 Document Number: 81775
.35 ±.1 2 ±.1 4 ±.1 1.5 ±.1 1.75 ±.1 11.5 ±.1 12.5 ±.1 24 ±.3 5 max. 5 max. X X 8 ±.1 1.5 ±.1 3.9 ±.1 4.65 ±.1 Section X-X R.76 Fig. 8 - Tape and Reel Packing for Option 8 (2 units per reel) Rev. 1.7, 18-Feb-13 7 Document Number: 81775
Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 217 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 8-Feb-17 1 Document Number: 91