H-Pile & Wide Flange C C () Flange Width () + 1 E Max (C) FLNGES OU OF SQ. MX WE OFF CENER MX EPH NY CROSS SEC. ll Up to 12- Over 12- /16 is measured at center line of web, is measured parallel to flange, C is measured parallel to web * hrough 426 lbs/ft, over 426 lbs/ft, /16-. permissible variations in LENGH from Specified Length for Lengths Given 30-FOO N 30-FOO 24-Inch and Under in Nominal 3/8 plus 1/16 for each additional feet or fraction thereof 3/8 24-Inch in Nominal Length & Columns plus 1/16 for each additional feet or fraction thereof
merican Standard/Channel 1 * S Shapes () Flange Width () Max (C) Sections Nominal Size (Inches) OU OF SQURE PER INCH OF IN INCHES S Shapes 3-7 Over 7-14 Over 14 3/32- - - 1/16-3/32- - - /32- - - /32- - 1/32-1/32-1/32- Channel Shapes 3-7 Over 7-14 Over 14 3/32- - - 1/16-3/32- - - - - - /32- - 1/32-1/32-1/32- is measured at center line of web permissible variations in LENGH UP O 30 F (with 30 ft included) from Specified Length for Lengths Given 30 F O 40 F 40 F O 0 F (with 0 ft included) 0 F O 6 F (with 6 ft included) 6 F S Shapes & 2 es 2 es 2 es 2 es 2 es S Shapes &
H-Pile/Wide Flange/Standard/Channel Camber Sweep Camber Sweep Horizontal Surface W, HP Shapes permissible variations in Camber & sweep in Inches Length CMER SWEEP with flange width equal to or greater than 6 es ll x total length (in feet) with flange width equal to or greater than 6 es ll x total length (in feet) x total length (in feet) Certain sections with flange width approximately equal to depth & specified on order as columns 4 Ft. and Under Over 4 Ft. x total length (in feet) (with 3/8 max) x total length (in feet) 3/8 + other tolerances for H-pile & wide flange Variation in Weight ± 2.% of theoretical or published weight Ends out of Square 1/64 per of depth, or flange width if it is greater than depth other tolerances for Standard & Channel Variation in Weight ± 2.% of theoretical or published weight Camber x total length (in feet) Ends out of Square 1/64 per of depth, or flange width if it is greater than depth Sweep x total length (in feet)
ngles () Flange Width () E Nominal Size FLNGES OU OF SQ. MX WE OFF CENER MX L ngles 3-4 (including 4) Over 4-6 (including 6) Over 6-8 (including 8) - 3/32-3/128- * - - 3/128- * - 1-8- 3/128- * * 3/128- per = 1 degrees. permissible variations in LENGH from Specified Length for Lengths Given UP O 30 F (with 30 ft included) 30 F O 40 F 40 F O 0 F (with 0 ft included) 0 F O 6 F (with 6 ft included) 6 F L ngles - 3/4-1- 1-1 - L ngles - - - - - CMER straightness in Inches CMER HORIZONL SURFCE x total length (in feet) Sweep tolerances are subject to negotiation for the individual shapes involved.
Structural ees Generally, any w or s shape from 6 to 36 es in depth can be split to form tees ee ee Shape - ee Shape ee Shape Center Splitting Off-Center Splitting wo Lines of Cut Nominal W-Shape in Inches 6 to 16 es (excluding 16) 16 to 20 es (excluding 20) 20 to 24 es (excluding 24) 24 es and Over Variation from ee Over and Under in Inches /16 3/8 ll weight, length and ends out of square variations for split tees are the same as those applicable to the shape from which the tees are split. Straightness in Inches CMER x total length (in feet)