Squares Tote Finished Size: 15" x 20" x 5" Supplies Needed Paris Collection 2 pkgs. Fabric Palette Paris Charms (5" x 5") 3 Fabric Palette Singles ( x 21") 2 matching for lining & 1 for handles and tabs 19" x 45" Fusible Fleece Coordinating thread 1 Sew-on snap (large) 5" x 14" Heavy cardboard & glue Rotary cutter, mat and acrylic ruler Removable fabric marker Basic sewing supplies Sewing machine Iron and pressing surface B efore you begin Read all instructions before beginning project. Do not pre-wash fabrics. Press fabrics with a dry iron on cotton setting before cutting. Use a ¼" seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Press seams in the directions of the arrows. Cutting 2 Singles: 2 x 21" (lining) 1 Single: 2 4" x 21" (handles); 8 2" x 2 ½" (handle tabs); 1 8" x (cardboard bottom cover) Fusible Fleece: 2 x 22 ½" Sewing Note: Bag as shown is made from the Paris fabric collection. Follow fabric key below or arrange fabric as desired. To make this bag from other fabric collections, simply substitute the fabrics and arrange as desired. A B C D E F G 2016 Fabric Editions, Inc. Fabric Palette is a trademark of Fabric Editions, Inc. page 1
1. Refer to Diagram A to arrange the Charms in four rows of five each as shown or arrange as desired to make the Tote front. Sew the Charms (RST) in rows; press. Sew the rows together, nesting the seams; press. The pieced Tote front should measure x 22 ½". Repeat to make the Tote back. A B C D E F G Dia. A Row 1 Row 2 Row 3 Row 4 A B C F D B D E G A B C E F G A C D E F x 22 ½" 2. Place the Tote front and back wrong side up on a flat surface, layer the fusible batting ( x 22 ½") glue side down on each. Fuse according to the manufacturer s directions (Dia. B). Dia. B Batting Tote Fuse batting to wrong side of tote front and back 3. To cut the Tote shape, fold the front side edges together and press a crease to mark the center. At the top edge, measure 10 ½" from the center on each side and make a mark. At the bottom edge, measure 9 ½" from the center on each side and make a mark. Draw a line from the top to the bottom mark on each side and cut along the lines. Note: The cut piece should measure 21" top width, 19" bottom width and side length. Repeat for the Tote back (Dia. C). Dia. C Fold 10 ½" 10 ½" 21" 9 ½" Wrong side of Tote front and back 9 ½" 19" to size page 2
4. Repeat Step 3 to cut the lining pieces the same size (Dia. D). Dia. D Fold 10 ½" 10 ½" 21" 9 ½" 9 ½" Lining front and back 19" Repeat for lining 5. Pin the Tote front and back (RST) around the sides and bottom so the Charm seams match; sew and press seams open. Tip: Use a rolled up towel inside the bag to press the seams open. Repeat to sew the two lining pieces, leaving a 6" opening in the bottom to turn right side out (Dia. E). Dia. E Tote Leave 6" opening Lining 6. To box the bottom, bring center bottom seam to the side seam RST. Mark 2 ½" from the point and stitch from edge to edge. the point to a ½" seam (Dia. F). Repeat for the other side. Turn bag right side out. Press the bottom edges square. Repeat to square the bottom of the lining. Note: Do not turn lining right side out. Dia. F 2 ½" Wrong side Wrong side to ½" 7. Press a handle piece (4" x 21") in half, wrong sides together so long edges meet. Open and press the long edges to the center fold. Fold the handle so pressed edges meet and topstitch close to both edges (Dia. G). Repeat for the second handle. Dia. G Fold to center Center fold Fold to center 8. Measure in ¼" from each side of a handle tab along the bottom edge and make a mark. Draw a line from the mark to the top corner on each side. Cut along the drawn lines so handle tab measures 2" along the bottom edge. Repeat for a total of eight. Place two shapes RST and sew with a ¼" seam around all sides; trim the corners. Carefully cut a plus in one side only. Turn right side out through the cut opening. Gently push out the corners; press flat. Repeat to make a total of four (Dia. H). Dia. H 2 ½" 2" 2" Make 8 Cut one side only Make 4 page 3
9. Position the ends of the handles 1 ¾" from the top edge and 3 ¼" from the center on each side. Pin and baste in place (Dia. I). Dia. I Center 1 ¾" 3 ¼" 10. Center one handle tab over the ends of each handle with the wide edge facing the top of the Tote and the cut plus face down. Pin in place; topstitch close to the edge around all four sides to secure the tabs and anchor the ends of the handles (Dia. J). Dia. J 11. Place the Tote inside the lining RST matching the side seams; pin and sew around the top edge. Note: Check that the handles are kept free of the seam. Turn right side out through the opening in the lining (Dia. K). Sew the opening in the lining closed. Dia. K page 4
12. Press the top edge flat then topstitch ¼" from the edge, keeping the handles free (Dia. L). Dia. L Finishing 13. Center the two sides of a large snap on each side of the lining ½" from the top edge, sew by hand to attach. 14. Wrap the cardboard bottom cover (8" x ) around the back of the piece of cardboard (5" x 14"); glue in place. Place in bottom of Tote. Finished Care Instructions: Wipe with damp cloth when needed. page 5