HMC754SGE v.49 Typical Applications The HMC754SGE is ideal for: CATV / Broadband Infrastructure Test & Measurement Equipment Line Amps and Fiber Nodes Customer Premise Equipment Functional Diagram Output ip2: +7 m High Gain: 14.5 High Output ip3: +3 m 75 Ohm Impedance Single Positive Supply: +5V Robust 1V esd, Class 1C soic- smt Package General Description The HMC754SGE is a GaAs/InGaP HBT Dual Channel Gain Block mmic SMT amplifier covering DC to 1 GHz. This versatile product contains two gain blocks, packaged in a single lead plastic soic-, for use with both amplifiers combined in push-pull configuration using external baluns to cancel out second order non-linearities and improve IP2 performance. In this configuration, the HMC754SGE offers high gain, very low distortion & simple external matching. This high linearity amplifier consumes only 16mA from a single positive supply. Electrical Specifications, T A = +25 C, Vcc1 = Vcc2 = 5V, Zo = 75 Ohm [1] Gain Parameter Min. Typ. Max. Units.5 -.5 GHz.5 -.7 GHz.7-1. GHz Gain Variation Over Temperature.5 -.7 GHz. / C Input Return Loss Output Return Loss.5 -.5 GHz.5 -.7 GHz.5 -.5 GHz.5 -.7 GHz Reverse Isolation.5 -.7 GHz 23 Output Power for 1 Compression (P1).5 -.7 GHz 19.5 21 m Output Third Order Intercept Point (IP3) (Pout= m per tone, 1 MHz spacing) 13.5 12.7 12.1 14.7 14.2 13.4 17 1 1 2.5 -.7 GHz 3 m Output Second Order Intercept Point (IP2).5 -.5 GHz 7 m Composite Second Order (CSO) [2].5 -.7 GHz -1 c Composite Triple Beat (CTB) [2].5 -.7 GHz -75 c Cross Modulation (XMOD) [2].5 -.7 GHz -67 c Noise Figure.5 -.5 GHz.5 -.7 GHz Supply Current (Icc1 + Icc2) 145 16 175 ma [1] Data taken with dual amplifiers combined in push-pull (default) configuration [2] Input level +15 mv, 133 channels - with analog modulation Features 5.5 6.5-1 For price, delivery and to place orders: Hittite Microwave Corporation, For price, 2 delivery, Alpha and Road, to place Chelmsford, orders: Analog MA Devices, 124Inc., One Technology Way, P.O. Box 916, Norwood, MA 262-916 Phone: 97-25-3343 Fax: 97-25-3373 Order Phone: On-line 71-329-47 at www.hittite.com Application Support: Phone: 97-25-3343 Application or apps@hittite.com Support: Phone: 1--ANALOG-D
v.49 HMC754SGE Gain & Return Loss 2 1 Gain vs. Temperature 1 15 RESPONSE () -1-2 -3 S21 S11 S22-4 Input Return Loss vs. Temperature RETURN LOSS () -5-1 -15-2 -25 5C -4C -3 Output IP3 vs. Temperature 42 4 GAIN () 12 9 6 3 5C -4C Output Return Loss vs. Temperature RETURN LOSS () -5-1 -15-2 -25 5C -4C -3 Output IP2 vs. Temperature 1 9 IP3 (m) 3 36 34 32 5C -4C IP2 (m) 7 6 5C -4C 3 5.5.1.15.2.25.3.35.4.45.5 For price, delivery and to place orders: Hittite Microwave Corporation, For price, 2 delivery, Alpha and Road, to place Chelmsford, orders: Analog MA Devices, 124Inc., One Technology Way, P.O. Box 916, Norwood, MA 262-916 Phone: 97-25-3343 Fax: 97-25-3373 Order Phone: On-line 71-329-47 at www.hittite.com Application Support: Phone: 97-25-3343 Application or apps@hittite.com Support: Phone: 1--ANALOG-D - 2
v.49 HMC754SGE Noise Figure vs. Temperature NOISE FIGURE () 1 6 4 2 5C -4C Reverse Isolation vs. Temperature REVERSE ISOLATION () -5-1 -15-2 -25 5C -4C -3 P1 vs. Temperature Output IP2 vs. Output Power CSO / CTB / XMOD @ +15 mv input, 133 channels (Analog) RESPONSE (c) -5-6 -7 - P1 (m) IP2 (m) 25 2 15 1 5 5C -4C 9 6 2 7 74 Pout = -3m Pout = m Pout = 3m Pout = 6m 7.5.1.15.2.25.3.35.4.45.5 CSO- CSO+ CTB XMOD -9-1 - 3 For price, delivery and to place orders: Hittite Microwave Corporation, For price, 2 delivery, Alpha and Road, to place Chelmsford, orders: Analog MA Devices, 124Inc., One Technology Way, P.O. Box 916, Norwood, MA 262-916 Phone: 97-25-3343 Fax: 97-25-3373 Order Phone: On-line 71-329-47 at www.hittite.com Application Support: Phone: 97-25-3343 Application or apps@hittite.com Support: Phone: 1--ANALOG-D
v.49 HMC754SGE Output IP3 vs. Frequency IP3 (m) 42 4 3 36 34 32 Option 1 - Improved Input Return Loss & Gain Flatness (with Lower IP2) Application Gain & Return Loss RESPONSE () 2 1-1 -2-3 S21 S11 S22-4 3 25 P1 vs. Frequency Output IP2 vs. Frequency IP2 (m) Noise Figure vs. Frequency NOISE FIGURE () 1 9 7 6 5 1 9 7 6 5 4 3 2 1.5.1.15.2.25.3.35.4.45.5 2 P1 (m) 15 1 5 For price, delivery and to place orders: Hittite Microwave Corporation, For price, 2 delivery, Alpha and Road, to place Chelmsford, orders: Analog MA Devices, 124Inc., One Technology Way, P.O. Box 916, Norwood, MA 262-916 Phone: 97-25-3343 Fax: 97-25-3373 Order Phone: On-line 71-329-47 at www.hittite.com Application Support: Phone: 97-25-3343 Application or apps@hittite.com Support: Phone: 1--ANALOG-D - 4
Gain & Return Loss 2 1 v.49 Option 2-1 to 1 MHz Application Output IP3 vs. Frequency 42 4 HMC754SGE RESPONSE () Noise Figure vs. Frequency NOISE FIGURE () -1-2 -3-4 1 2 3 4 5 6 7 9 1 1 9 7 6 5 4 3 2 1 S21 S11 S22 FREQUENCY (MHz) 1 2 3 4 5 6 7 9 1 FREQUENCY (MHz) IP3 (m) P1 vs. Frequency P1 (m) 3 36 34 32 3 25 2 15 1 5 1 2 3 4 5 6 7 9 1 FREQUENCY (MHz) - 5 For price, delivery and to place orders: Hittite Microwave Corporation, For price, 2 delivery, Alpha and Road, to place Chelmsford, orders: Analog MA Devices, 124Inc., One Technology Way, P.O. Box 916, Norwood, MA 262-916 Phone: 97-25-3343 Fax: 97-25-3373 Order Phone: On-line 71-329-47 at www.hittite.com Application Support: Phone: 97-25-3343 Application or apps@hittite.com Support: Phone: 1--ANALOG-D
v.49 HMC754SGE Absolute Maximum Ratings Collector Bias Voltage (Vcc) RF Input Power (rfin) Outline Drawing +5.5 Vdc +1 m Junction Temperature 15 C Continuous Pdiss (T = 5 C) (derate 1.69 mw/ C above 5 C) Thermal Resistance (junction to ground paddle) 1.21 W 53.5 C/W Storage Temperature -65 to +15 C Operating Temperature -4 to +5 C ESD Sensitivity (HBM) Package Information Class 1C Part Number Package Body Material Lead Finish msl Rating Package Marking [3] [2] HMC754 HMC754SGE RoHS-compliant Low Stress Injection Molded Plastic 1% matte Sn msl1 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 26 C [3] 4-Digit lot number XXXX NOTES: ELECTROSTATIC sensitive Device OBserve HANDlinG precautions 1. leadframe MATeriAL: copper AlloY 2. Dimensions ARE in inches [millimeters] 3. Dimension Does not include moldflash of.15mm per side. 4. Dimension Does not include moldflash of.25mm per side. 5. ALL GROUND leads AND GROUND PADDLE MUST BE soldered TO pcb rf GROUND. For price, delivery and to place orders: Hittite Microwave Corporation, For price, 2 delivery, Alpha and Road, to place Chelmsford, orders: Analog MA Devices, 124Inc., One Technology Way, P.O. Box 916, Norwood, MA 262-916 Phone: 97-25-3343 Fax: 97-25-3373 Order Phone: On-line 71-329-47 at www.hittite.com Application Support: Phone: 97-25-3343 Application or apps@hittite.com Support: Phone: 1--ANALOG-D - 6
v.49 HMC754SGE Pin Descriptions Pin Number Function Description Interface Schematic 1, 4 RFIN1, RFIN2 5, RFOUT1/vcc1, RFOUT2/vcc2 2 GND 3, 6, 7 N/C These pins are DC coupled. An off chip DC block capacitor is required. RF Output and DC bias for the output stage. These pins and package bottom must be connected to RF/ DC ground. No connection. These pins may be connected to RF ground. Performance will not be affected. - 7 For price, delivery and to place orders: Hittite Microwave Corporation, For price, 2 delivery, Alpha and Road, to place Chelmsford, orders: Analog MA Devices, 124Inc., One Technology Way, P.O. Box 916, Norwood, MA 262-916 Phone: 97-25-3343 Fax: 97-25-3373 Order Phone: On-line 71-329-47 at www.hittite.com Application Support: Phone: 97-25-3343 Application or apps@hittite.com Support: Phone: 1--ANALOG-D
v.49 HMC754SGE Application Circuit for Push-Pull Operation Components for Selected Options Tune Options Standard Option 1 Option 2 Evaluation PCB Number 12463 126311 12425 T1 [1] ETC 1-1-13 MABACT39 ETC1-1T-5TR T2 [1] ETC 1-1-13 ETC 1-1-13 ETC1-1T-5TR L1, L2 1 nh 1 nh 1 uh C13 Open 1.1 pf Open [1] 1:1 Transformer For price, delivery and to place orders: Hittite Microwave Corporation, For price, 2 delivery, Alpha and Road, to place Chelmsford, orders: Analog MA Devices, 124Inc., One Technology Way, P.O. Box 916, Norwood, MA 262-916 Phone: 97-25-3343 Fax: 97-25-3373 Order Phone: On-line 71-329-47 at www.hittite.com Application Support: Phone: 97-25-3343 Application or apps@hittite.com Support: Phone: 1--ANALOG-D -
v.49 HMC754SGE Evaluation PCB - Standard and Option 2 Application List of Materials for Evaluation PCB [1] Item Description J1, J2 F-Connector J3 - J6 C1 - C6 DC pin 1 nf Capacitor, 42 Pkg. C7, C 4.7 µf Capacitor, Tantalum, 63 Pkg. C9, C11 6 pf Capacitor, 42 Pkg. C1, C12 1 nf Capacitor, 42 Pkg. L1, L2 [2] Inductor, 63 Pkg. R1, R2 Ohm Resistor, 63 Pkg. T1, T2 [2] 1:1 Transformer U1 PCB [3] HMC754SGE Amplifier 12461 Evaluation pcb [1] When requesting an evaluation board, please reference the appropriate evaluation pcb number listed in the table Components for Selected Options. [2] Please refer to Components for Selected Options table for values [3] Circuit Board Material: Rogers 435 or Arlon 25FR The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 75 ohm impedance while the package ground leads and package bottom should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. - 9 For price, delivery and to place orders: Hittite Microwave Corporation, For price, 2 delivery, Alpha and Road, to place Chelmsford, orders: Analog MA Devices, 124Inc., One Technology Way, P.O. Box 916, Norwood, MA 262-916 Phone: 97-25-3343 Fax: 97-25-3373 Order Phone: On-line 71-329-47 at www.hittite.com Application Support: Phone: 97-25-3343 Application or apps@hittite.com Support: Phone: 1--ANALOG-D
v.49 HMC754SGE Evaluation PCB - Option 1 Application List of Materials for Evaluation PCB [1] Item Description J1, J2 F-Connector J3 - J6 C1 - C6 DC pin 1 nf Capacitor, 42 Pkg. C7, C 4.7 µf Capacitor, Tantalum, 63 Pkg. C9, C11 6 pf Capacitor, 42 Pkg. C1, C12 1 nf Capacitor, 42 Pkg. C13 1.1 pf Capacitor, 42 Pkg. L1, L2 1 nh Inductor, 63 Pkg. R1, R2 Ohm Resistor, 63 Pkg. T1, T2 [2] 1:1 Transformer U1 PCB [3] HMC754SGE Amplifier 12639 Evaluation pcb [1] When requesting an evaluation board, please reference the appropriate evaluation pcb number listed in the table Components for Selected Options. [2] Please refer to Components for Selected Options table for values [3] Circuit Board Material: Rogers 435 or Arlon 25FR The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 75 ohm impedance while the package ground leads and package bottom should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, For price, 2 delivery, Alpha and Road, to place Chelmsford, orders: Analog MA Devices, 124Inc., One Technology Way, P.O. Box 916, Norwood, MA 262-916 Phone: 97-25-3343 Fax: 97-25-3373 Order Phone: On-line 71-329-47 at www.hittite.com Application Support: Phone: 97-25-3343 Application or apps@hittite.com Support: Phone: 1--ANALOG-D - 1