DPS Series 5W, 1W, 18W AC/DC DI Rail Power Supplies AC - DC din rail mountable 5W, 1W and 18W class 2 power supplies E A R G U A R A T E E z U, cu, CE z Universal input 9~265VAC z High efficiency up to 2% z Short circuit protection z Internal input filter z 3 ear warranty Specificaton Model DPS-1-5-24 DPS-1-1-24 DPS-1-18-24 Input Voltage 9~265VAC Output Wattage 5W 1W 18W Output Voltage 24VDC (Other output voltages available on request) Output 21mA 42mA 5mA Efficiency (min/typ) /2% 4/6% 5/% General Specification frequency khz voltage 3VAC resistance MΩ @ 5VDC Ambient temperature -1 to +1 C Derating (from 61 to 1 C) 2.5%/ C 3%/ C 3%/ C Storage temperature -25 to +85 C Relative humidity 2 to 95% RH Cooling Free air convection Dimensions 9 x W22.5 x D mm Weight g 12g 15g Case material Plastic Input Specifications Rated input voltage to 24VAC Input voltage range 9 to 265VAC, 12 to 3VDC ine frequency 4 to 63Hz Inrush current 1A @ VAC, 18A @ 23VAC Output Specifications Output voltage accuracy ±1% Minimum load % ine regulation ±1% oad regulation ±2% Transient recovery time 3µS @ 5% load, step changed Temperature coefficient ±.2%/ C Ripple & noise 5mV Hold up time 3mS @ VAC, 13mS @ 23VAC Voltage trim range -1 to +2% DC O indicator threshold at start up 21.6VDC DC OW indicator threshold after start up 18 to 21.6VDC Control and Protection Input fuse T2A / 25VAC internal Rated over load protection 11 to 135% Over voltage protection 125 to 145% Output short circuit Hiccup mode Approvals and Standards CE, U/cU DPS-1-5-1-18//
DPS Series 5W, 1W, 18W AC/DC DI Rail Power Supplies Dimensions (mm) 9 Key Description V+ (1) Positive output terminal 22.5 V- (2) egative output terminal 22.5 2(3) 1 Ground this terminal to minimize high-frequency emissions (4) Input terminals 2 1 (neutral conductor, no polarity at DC input) (5) Input terminals (phase conductor, no polarity at DC input) V - V+ O DC Output Operation indicator ED V - V+ O O DC OW DC Output indicator ED O Trimmer-potentiometer for Vout adjustment O O Construction Installation 9 Easy, safe and secure snap-on, snap-off DI-Rail mounting (TS35/.5 or TS35/15) 3 4 5 3 4 5 Ventilation/Cooling ormal convection All sides 25mm free space for cooling recommended Terminal size range 2 Solid:.2-2.mm (AWG24-14) (use copper conductors only) 9 2 1 V - 22.5 V+ DC Output O O 3 4 5 Derating 5 5 DPS-1-5 DPS-1-1 DPS-1-18 -1 61 1-1 61 1-1 61 1-1 61 1 Connections ine Inrush imiter and Inrush ine imiter and Control Control Output evel DC O (Green ED) Output DC OW evel (Red ED) DC O (Green ED) DC OW (Red ED) DPS-1-5-1-18//
DPS Series 3W, 6W AC/DC DI Rail Power Supplies AC - DC DI rail mountable 3W and 6W class 2 power supplies E A R G U A R A T E E z U, cu, CE z Universal input 85~264VAC z High efficiency z Short circuit protection z Internal input filter z 3 ear warranty Specificaton Model DPS-1-3-24 DPS-1-6-24 Input Voltage 85~264VAC Output Wattage 3W 6W Output Voltage 24VDC (Other output voltages available on request) Output 125mA 25mA Efficiency (min/typ) 83/86% 86/89% General Specification voltage 3VAC resistance MΩ @ 5VDC Ambient temperature -1 to +1 C Derating (from 61 to 1 C) 2.5%/ C Storage temperature -25 to +85 C Relative humidity 2 to 9% RH Cooling Free air convection Dimensions 9 x W4.5 x D mm Weight 29g 36g Case material Plastic Input Specifications Rated input voltage to 24VAC Input voltage range 85 to 264VAC, 9 to 35VDC ine frequency 4 to 63Hz Inrush current 2A @ VAC, 4A @ 23VAC 3A @ VAC, 6A @ 23VAC Output Specifications Output voltage accuracy ±1% Minimum load % ine regulation.5% oad regulation.5% Turn on time ms after AC applied to input at full resistive load Voltage fall time 15mS Voltage rise time 15mS at full resistive load Hold up time 2mS @ VAC, 3mS @ 23VAC Temperature coefficient ±.2%/ C Ripple & noise 5mV Voltage trim range 24 to 28VDC DC O indicator threshold at start up 19.2VDC Control and Protection Rated over load protection 11 to 14% 11 to 15% Over voltage protection 3 to 33VDC Output short circuit Fold forward Approvals and Standards CE, U/cU DPS-1-3-6//
9 DC O DPS Series 3W, 6W AC/DC DI Rail Power Supplies 6 Dimensions (mm) 8 Pin connections 5 9 5 4 3 2 1 - - 4.5 DC O + +Rdy 6 8-1 61 1 Connections 9 22.5 2 1 3 4 5 ine V - V+ Inrush DC Output imiter and O 5 O 9 5 4 3 2 1-6 - 4.5 DC O + +Rdy 8 Rdy -Vout Rdy -Vout Output evel -1 61 1 Key Description Rdy (1) DC OK output for relay (24V models only) + R (2) >Ω Positive output terminal + (3) Positive output terminal - (4) egative output terminal - (5) egative output terminal (6) Ground terminal to minimize high-frequency emissions () Input terminals (neutral conductor, no polarity at DC input) (8) Input terminals (phase conductor, no polarity at DC input) a) DC Relay O Operation indicator ED Trimmer-potentiometer for Vout adjustment 2.2K.5W Installation Ventilation/Cooling ormal 5.1K convection.3w All sides 25mm free space for cooling recommended b) 5V signal Terminal size range 2 Solid:.2-2.mm (AWG24-14) (use copper conductors only) DC O (Green ED) RD(Open Collector)* Rdy -Vout Rdy -Vout Construction Easy, safe and secure snap-on, snap-off DI-Rail mounting (TS35/.5 or TS35/15) R >Ω a) Relay 2.2K.5W 5.1K.3W b) 5V signal Derating Rdy connections 5 ine Inrush imiter and DPS-1-3-6// -1 61 1-1 61 Output evel 1 DC O (Green ED) RD(Open Collector)*
DPS Series 12W AC/DC DI Rail Power Supplies AC - DC DI rail mountable 12W power supplies E A R G U A R A T E E z Compact design z High efficiency up to 86% z function available z Parallel function available (switch) z Input voltage /23VAC auto select z 3 ear warranty Specificaton Model DPS-1-12-24 Input Voltage /23VAC Output Wattage 12W Output Voltage 24VDC (Other output voltages available on request) Output 5A Efficiency (min/typ) 84/86% General Specification voltage 3VAC resistance MΩ @ 5VDC Ambient temperature -25 to +1 C Derating (from 61 to 1 C) 2.5%/ C Storage temperature -25 to +85 C Relative humidity 2 to 95% RH Cooling Free air convection Dimensions 123.6 x W63.2 x D123.6 mm Weight 92g Case material Metal Input Specifications Rated input voltage Input voltage range Rated input current ine frequency Inrush current Output Specifications Output voltage accuracy /23VAC V: 9 to 132VAC, 23V: 186 to 264VDC 2.8/1.4A 4 to 63Hz 24A @ VAC, 48A @ 23VAC. @ 23VAC to 1% (adjusted pre-shipment) Minimum load % ine regulation ±.5% oad regulation Hold up time Temperature coefficient Ripple & noise Voltage trim range DC O indicator threshold at start up DC O indicator threshold after start up Parallel operation Control and Protection Input fuse ±1% single mode, ±5% parallel mode 25mS @ VAC, 3mS @ 23VAC ±.3%/ C 5mV 22.5 to 28.5VDC 1.6 to 19.4VDC 1.6 to 19.4VDC up to 3 units T3.15A/25VAC internal Rated over load protection 11 to 145% Power Rdy (24V model only) Electrical isolation: 5VDC Threshold volt. contact closed (start up): 1.6 to 19.4VDC Contact rating:.3a @ 6VDC Over voltage protection 125 to 145% Output short circuit Approvals and Standards limited CE, U/cU DPS-1-12//
DPS Series 12W 63.2 AC/DC DI Rail Power 9 Supplies Dimensions (mm) Pin connections 6 - - S P DC O DC O 63.2 1 ++ Rdy 9 Inrush imiter, and Auto /23VAC 123.6 116.6. Smoothing Key Description Rdy(1,2) DC O output for relay (24V models only) + (3) Positive output terminal + (4) Positive output terminal - (5) egative output terminal - (6) egative output terminal () Ground terminal to minimize Single/Parallel high-frequency emissions (8) Reference Input terminals & (phase conductor, no polarity at DC input) (9) Input terminals (neutral conductor, no polarity at DC input) DC O Operation indicator ED DC O DC low voltage indicator ED Trimmer-potentiometer for Vout adjustment DC O (Green ED) S/P Single/Parallel Output select evelswitch DC O (Red ED) RD (Relay Contact)* Installation Construction Derating Ventilation/Cooling ormal convection All sides 25mm free space for cooling recommended Easy, safe and secure snap-on, snap-off DI-Rail mounting (TS35/.5 or TS35/15) Screw Terminal 1-24AWG flexible/solid cable Strip cable ends by 8mm 5 123-25 61 1 Connections Inrush imiter, and Auto /23VAC Smoothing Single/Parallel Output evel DC O (Green ED) DC O (Red ED) RD (Relay Contact)* DPS-1-12//
DPS Series 24W AC/DC DI Rail Power Supplies AC - DC DI rail mountable 24W power supplies E A R G U A R A T E E z Compact design z High efficiency up to 89% z function available z Parallel function available (switch) z Input voltage /23VAC auto select z 3 ear warranty Specificaton Model DPS-1-24-24 Input Voltage /23VAC Output Wattage 24W Output Voltage 24VDC Output 1A Efficiency (min/typ) 8/89% General Specification voltage 3VAC resistance MΩ @ 5VDC Ambient temperature -1 to +1 C Derating (from 61 to 1 C) 2.5%/ C Storage temperature -25 to +85 C Relative humidity 2 to 95% RH Cooling Free air convection Dimensions 125 x W83 x D126 mm Weight g Case material Metal Input Specifications Rated input voltage Input voltage range Rated input current ine frequency Inrush current Output Specifications Output voltage accuracy /23VAC V: 93 to 132VAC, 23V: 186 to 264VDC 5.4/2.2A 4 to 63Hz 3A @ VAC, 6A @ 23VAC. @ 23VAC to 1% (adjusted pre-shipment) Minimum load % ine regulation ±.5% oad regulation Hold up time Temperature coefficient Ripple & noise Voltage trim range DC O indicator threshold at start up DC O indicator threshold after start up Parallel operation Control and Protection Input fuse ±1% single mode, ±5% parallel mode 25mS @ VAC, 3mS @ 23VAC ±.2%/ C mv 22.5 to 28.5VDC 1.6 to 19.4VDC 1.6 to 19.4VDC up to 3 units T6.3A/25VAC internal Rated over load protection 12 to 145% Power Rdy Electrical isolation: 5VDC Threshold volt. contact closed (start up): 1.6 to 19.4VDC Contact rating:.3a @ 6VDC Over voltage protection 12 to 145% Output short circuit Approvals and Standards limited CE, U/cU DPS-1-24//
DPS Series 24W 83 AC/DC DI Rail Power Supplies Dimensions (mm) Pin connections S P 6 83 1 Inrush - -++ Rdy imiter, and Auto /23VAC DC O DC O 9 125 Smoothing 116 1 Key Description Rdy(1,2) DC O output for relay (24V models only) + (3) Positive output terminal + (4) Positive output terminal - (5) egative output terminal - (6) egative output terminal () Ground terminal to minimize Single/Parallel high-frequency emissions (8) Reference Input terminals & (phase conductor, no polarity at DC input) (9) Input terminals (neutral conductor, no polarity at DC input) DC O Operation indicator ED DC O DC low voltage indicator ED Trimmer-potentiometer for Vout adjustment DC O (Green ED) S/P Single/Parallel Output select evelswitch DC O (Red ED) RD (Relay Contact)* Installation Construction Derating Ventilation/Cooling ormal convection All sides 25mm free space for cooling recommended Easy, safe and secure snap-on, snap-off DI-Rail mounting (TS35/.5 or TS35/15) Screw Terminal 1-24AWG flexible/solid cable Strip cable ends by 8mm 5 1 9-1 61 1 Connections Inrush imiter, and Auto /23VAC Smoothing Single/Parallel Output evel DC O (Green ED) DC O (Red ED) RD (Relay Contact)* DPS-1-24//
DPS Series 48W AC/DC DI Rail Power Supplies AC - DC DI rail mountable 48W power supplies E A R G U A R A T E E z Compact design z High efficiency up to 89% z function available z Parallel function available (switch) z Universal input voltage z 3 ear warranty Specificaton Model DPS-1-48-24 Input Voltage 9~264VAC Output Wattage 48W Output Voltage 24VDC Output 2A Efficiency (min/typ) 86/89% General Specification voltage 3VAC resistance MΩ @ 5VDC Ambient temperature -25 to +1 C Derating (from 56 to 1 C) 2.5%/ C Storage temperature -25 to +85 C Relative humidity 2 to 95% RH Cooling Free air convection Dimensions 125 x W15 x D123 mm Weight 192g Case material Metal Input Specifications Rated input voltage Input voltage range Rated input current ine frequency Inrush current Output Specifications Output voltage accuracy /23VAC 9 to 264VAC (23VAC typ.), 12 to 3VDC A @ VAC, 3.5A @ 23VAC 4 to 63Hz 25A @ VAC, 5A @ 23VAC.99 @ 23VAC to 1% (adjusted pre-shipment) Minimum load % ine regulation ±.5% oad regulation Hold up time Temperature coefficient Ripple & noise Voltage trim range DC O indicator threshold at start up DC O indicator threshold after start up Parallel operation Control and Protection Input fuse ±.5% single mode, ±5% parallel mode 3mS ±.2%/ C mv 22.5 to 28.5VDC 1.6 to 19.4VDC 1.6 to 19.4VDC up to 3 units 1A/25VAC internal Rated over load protection 12 to 14% Power Rdy Over voltage protection Output short circuit Approvals and Standards Electrical isolation: 5VDC Threshold volt. contact closed (start up): 1.6 to 19.4VDC Contact rating:.3a @ 6VDC 3 to 33V Continuous current limited CE, U/cU DPS-1-48//
1 DC O DC O Rdy++ - - P DPS Series 48W S Vout 9 AC/DC DI Rail Power Supplies adj. 1 6 15 Dimensions (mm) Derating 62.5 9 Bridge DC O DC O Rdy++ - - 15 P S 1 6 DC O DC O 125 63.2-25 56 9 1 S P Active 6 - - 1 ++ Rdy 123.6 116. 116.6. Pin connections Key Description Rdy(1,2) DC O output for relay (24V models only) + (3) Positive output terminal + (4) Positive output terminal - (5) egative output terminal - (6) egative Single/Parallel output terminal () Ground terminal to minimize high-frequency emissions (8) Input terminals (neutral conductor, no polarity at DC input) (9) Input terminals (phase conductor, no DC polarity O (Green at DC ED) input) Output evel DC O Operation indicator ED DC O (Red ED) DC O DC low voltage indicator ED RD (Relay Contact)* Trimmer-potentiometer for Vout adjustment S/P Single/Parallel select switch Installation Ventilation/Cooling ormal convection All sides 25mm free space for cooling recommended Screw Terminal 1-24AWG flexible/solid cable Strip cable ends by 8mm Construction Easy, safe and secure snap-on, snap-off DI-Rail mounting (TS35/.5 or TS35/15) Connections Inrush imiter, and Auto /23VAC Smoothing Single/Parallel Output evel DC O (Green ED) DC O (Red ED) RD (Relay Contact)* DPS-1-48//