- ($ 0$$/ PP-,( /$( WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Part SP SAVE THIS MANUAL FOR FUTURE REFERENCE Printed in Taiwan
Parts List for RIDGID -/" Jointer/Planer Model JP0 Figure 0 0 0 0
Parts List for RIDGID -/" Jointer/Planer Model JP0 Figure Always order by Part Number - Not by Number Part Part 0 - - - 0-0 0 0- - - - Guard Cutter Table Infeed Pointer Indicator * Screw Pan Hd. - x / Knob Retainer Knob * Screw Pan Hd / x / Spring Retainer * Screw Pan Hd M x 0.- Gib * Screw Set /-0 x * Nut Hex /-0 Screw Elevation Washer Brass Clamp * Screw Set /-0 x / Collar Handwheel Screw Pan Hd /-0 x / * Lockwasher mm * Screw Cap /- x -/ Base Block Asm Depth 0 0 - - - - AC0 0 0-0 0- SP Screw Cap /- x / Knob Plunger Housing Plunger Spring Plunger Knob Outfeed Screw Wing /-0 x Pin Spring x 0 Slide Fence Washer / x 0mm x mm * Screw Cap /- x / Pin Roll mm x 0mm Table Outfeed Push Block Angle Gauge - Part A Angle Gauge - Part B * Wrench Hex L M * Wrench Box M/M Washer Flat mm Operator s Manual * Standard hardware item, may be purchased locally These replacement parts are available where you purchased your jointer.
Parts List for RIDGID -/" Jointer/Planer Model JP0 Figure 0 0
Parts List for RIDGID -/" Jointer/Planer Model JP0 Figure Always order by Part Number - Not by Number Part 0 0 Part 0-00 0-0 0-0 Holder Fence * Washer. x -/ x / Knob Fence Sleeve Fence Nut Tee Fence Plate Stop Bolt Shoulder mm x mm * Screw Hex Hd /- x -/ Plate Fence Pivot Screw Pivot Nut Hex Jam /- Knob Fence Tilt * Screw Hex Hd /- x * Nut Hex Jam /- Stud Pivot * Standard hardware item, may be purchased locally 0 0 0-0 0 0 0-0- 0 0-0 * Nut Hex Jam /-0 Fence * Screw Flat Hd Soc /- x -/ Nut Handle Bolt Shoulder x Nut Pivot Stop Fence * Nut Hex Jam /- Shaft Lock Collar Lock * Washer Flat / x / x / * Screw Pan Cr /-0 x / Handle Asm Bracket Fence Washer. I.D. x -/ x / * Screw Hex Hd /- x -/
Parts List for RIDGID -/" Jointer/Planer Model JP0 Figure 0
Parts List for RIDGID -/" Jointer/Planer Model JP0 Figure Always order by Part Number - Not by Number Part Part 0 - - Guard Pulley Screw Pan Cr Serr /- x / Panel Rear Panel Asm Right (Includes ) Grommet Bolt Rd Hd Sh Neck /- x / Nut Hex Flange /- Panel Asm Front * Standard hardware item, may be purchased locally 0-0- * Nut Hex /- Washer mm I.D. Foot Leveling / Panel Asm Left Chute Dust Screw Wing Bracket Motor Screw Hex Ser Fl /- x /
Parts List for RIDGID -/" Jointer/Planer Model JP0 Figure Always order by Part Number - Not by Number Part Part AC00 0-0- - Screw /- x mm Wedge Blade Screw Flat Hd Hex Soc M x 0.- Bearing Support Bearing 0- - 0 0- - * Soc Set Screw /-0 x / Pulley * Lockwasher M Screw Hex /- x -/ Cutter head Bearing Support Bearing These parts are available where you purchased your jointer.
Parts List for RIDGID -/" Jointer/Planer Model JP0 Figure 0 Always order by Part Number - Not by Number Part Part - 0-0 - Switch Switch Locking * Screw Ty AB M x.- Bezel Switch * Screw Pan Hd #- x / * Lockwasher # Plate Switch Bezel * Nut #- Box Switch Strain Relief P- 0 - - - 0-0 - - - Cord w/plug V-Belt A- Pulley Screw Set /-0 x / Motor * Bolt Rd Hd Sh /- x / Cord Motor Strain Relief N- Nut * Standard hardware item, may be purchased locally
Maintenance and Lubrication Maintenance Do not allow pitch to accumulate on the tables, the fence, the cutter guard, the cutterhead or the knives. Clean them with an appropriate solvent. Apply a thin coat of paste type wax to the tables and the fence so that the wood slides easily while feeding. This also deters rusting. Do not allow chips to accumulate on the underside of the jointer/planer. If power cord is worn, cut, or damaged in any way, have it replaced immediately. Lubrication WARNING: Unplug the jointer/planer. Unit could start suddenly. You could be badly hurt. The ball bearings in this machine are packed with grease at the factory. They required no further lubrication. Disassembly of the motor should only be done by an Authorized Service Center. Disregarding this may void your tools warranty. NOTE: The speed of this motor cannot be regulated or changed. Motors used on woodworking tools are particularly susceptible to the accumulation of sawdust and wood chips and should be blown out or vacuumed frequently to prevent interference with normal motor ventilation. The following parts should be oiled occasionally with SAE 0 or 0 engine oil.. Dovetail spacer and dovetail slide.. Elevation screw (first clean if necessary). Wiring Diagram Motor Junction Box Motor Junction Box White Green Black Wire Nut Black White Green Wire Nut 0V Wiring 0V Power Cord 0V Power Cord 0V Wiring