SBU Technlgy DCT 704x DIGITAL CABLE TUNER SPECIFICATION FEATURES Full frequency range frm 47 t 862 MHz Antenna lp thrugh functin Suitable fr lw and high data rates Lw phase nise Channel filter and IF AGC amplifier inside I2C bus cntrl Cmpatible t all majr sftware drivers MODEL DESCRIPTION PRODUCT REF. NO. DCT7042A DCT7043A DCT7046 DCT7047 with Channel filter and IF AGC amplifier inside, hrizntal munting, RH with Channel filter and IF AGC amplifier inside, hrizntal munting, LH with Channel filter and IF AGC amplifier inside, hrizntal munting, RH With F-cnnectr with Channel filter and IF AGC amplifier inside, hrizntal munting, LH With F-cnnectr 21415800 21421950 21467480 21477930 PRELIMINARY SPECIFICATION Page: 1/20
TABLE OF CONTENT 1 Brief descriptin... 3 2 Blck diagram... 3 3 Mechanical Specificatin... 4 3.1 Vertical munting... 4 3.2 DCT 7042A Hrizntal munting (Right hand pinning)... 5 3.3 DCT 7043A Hrizntal munting (Left hand pinning)... 6 4 Pin Definitins... 7 5 Operatinal Cnditins... 8 6 Standard Test Cnditins... 9 7 Electrical Characteristics... 10 7.1 Tuner... 10 7.2 Antenna Lp Thrugh... 11 8 Applicatin Infrmatin... 12 8.1 Tuner... 12 9 Electrstatic discharge... 13 9.1 Test... 13 9.2 Handling... 13 10 Reliability test prcedure & cnditins... 14 10.1 Heat lad test... 14 10.2 Humidity lad test... 14 10.3 Cld test... 15 10.4 Thermal shck... 15 10.5 Temperature cycle test... 15 10.6 Vibratin test... 16 10.7 Drp test... 16 10.8 Life test... 16 11 Appendix... 17 11.1 Packaging... 17 11.2 Identificatin / Trace ability... 18 11.3 Applicatin Circuit... 19 12 Revisin... 20 PRELIMINARY SPECIFICATION Page: 2/20
1 Brief descriptin The tuner DCT 704x is designed fr digital cable set tp bx applicatin in cmpliance with the Eurpean digital cable standard ETS 300 429. The tuner cnsists f a VHF/ UHF tuner, a SAW filter fr channel filtering, an IF amplifier with AGC and an antenna lp thrugh functin. The full frequency range frm 47 t 862 MHz is autmatically splitted int 3 bands and after gain setting and filtering cnverted t the standard IF frequency f 36 MHz by means f a mixer/scillatr IC. The tuner incrprates the Thmsn Universal Tuning System, which desn't require any band switching infrmatin. The unit is built n a lwlss printed circuit bard carrying all the cmpnents in a metal husing frame with tp and rear cvers. The aerial cnnectrs (IEC-male/female type) are munted n ne frame side; all ther cnnectins are made via pins at the bttm. The tuner cmplies with the requirements f radiatin, signal handling capability and immunity interference f CENELEC Eurpean standards EN55013 and EN55020. 2 Blck diagram SAW IF Amplifier Ant_in MOPLL TV_ut 1 1 RF_AGC +5V +33V I2C bus IF_ut IF_AGC PRELIMINARY SPECIFICATION Page: 3/20
3 Mechanical Specificatin 3.1 Vertical munting "!! PRELIMINARY SPECIFICATION Page: 4/20
3.2 DCT 7042A and DCT7046 Hrizntal munting (Right hand pinning) " # #% ()*+,--!$.*,(# &' #%!!#$!# * DCT7046 is with F-cnnectr (L=17.6) instead f IEC scket PRELIMINARY SPECIFICATION Page: 5/20
3.3 DCT 7043A and DCT7046 Hrizntal munting (Left hand pinning) 2.3() / #! # #!/ %1 & &!%/ /1/ # % %!/ 41// #% ()*+,--!$.*,(# &' #%!# %!# 4## # #!! &/&/!& /,56! #!'1 #$!!!/0/&&! #&!! ((()*+,--!!'1!1#!!# # #4## 7 &!%/ #$!!!/0/&&! * DCT7047 is with F-cnnectr (L=17.6) instead f IEC scket PRELIMINARY SPECIFICATION Page: 6/20
SBU Technlgy 4 Pin Definitins Pin Symbl Descriptin 1 RF_AGC Tuner AGC input 2 Vcc1 Supply vltage +5V (Antenna Lp Thrugh) 3 nc 4 Vcc2 Supply vltage +5V (Tuner) 5 nc 6 SCL I2C bus clck 7 SDA I2C bus data 8 AS Address select 9 Vt Tuning vltage +33V 10 Vcc3 Supply vltage +5V (IF amplifier) 11 IF_AGC IF AGC input 12 IF_ut + IF utput 13 IF_ut - IF utput PRELIMINARY SPECIFICATION Page: 7/20
SBU Technlgy 5 Operatinal Cnditins N Parameter Unit Min Typ Max Remarks 1. Supply vltage Vcc 1/2/3 V 4,75 5 5,25 ripple 20mVpp 2. Supply current Icc1 ma 50 65 3. Supply current Icc2 ma 86 110 4. Supply current Icc3 ma 125 150 5. Tuning vltage Vt V 31,5 33 34,5 ripple 10mVpp 6. Input signal at Ant_IN dbuv 60 7. RF AGC vltage V 0,1 4,0 0.2mA 8. IF AGC vltage V 0,1 2,0 0.2mA 9. IF utput Ω 1000 balanced 10. Ambient temperature C -10 60 11. Relative humidity % 90 Remark: The ripple vltage must be guaranteed in the final applicatin. The ripple frequency 100 Hz PRELIMINARY SPECIFICATION Page: 8/20
SBU Technlgy 6 Standard Test Cnditins N Parameter Unit Min Typ Max Remarks 1. Ambient temperature C 23 25 27 2. Relative humidity % 45 60 75 3. Vcc V 4,9 5 5,1 4. RF AGC vltage V 3,9 4,0 4,1 5. IF AGC vltage V 0 1,7 5. Vt V 31,5 33 34,5 6. Input impedance Ω 70 75 80 unbalanced 7. Output impedance Ω 1000 balanced Nte: A prper functin is guaranteed within the specified supply vltage and envirnmental cnditins but a certain deteriratin f perfrmance parameters may ccur at the limits f peratinal cnditins. PRELIMINARY SPECIFICATION Page: 9/20
7 Electrical Characteristics 7.1 Tuner N Parameters Unit Min Typ Max Remarks 1. Frequency range MHz 51 858 2. Frequency margin Lw end High end MHz 2 2 related t the center frequency f the channel 3. Input return lss db 8 Over full tuning range 4. Intermediate frequency MHz 36 5. Amplitude respnse curve f tuner part db 3 6. Vltage gain At IF utput db 95 7. Gain taper db 8 8. RF AGC range db 40 9. AGC range RF+IF db 80 center frequency, scillatr perates abve the input signal Difference in amplitude inside the channel bandwidth ±4 MHz. See nte 1 Max. vltage gain measured with Ant_In at 30dBuV wrt 1k hm lad Maximum value between AGC vltage 0,1...4,0 V Nte 1 RF AGC =4V (max.) IF AGC =1.7V (max.) 10. Nise figure db 8,5 AGC vltage = 4,0V 11. IF rejectin All channels except CH 02 db 12. Image rejectin db 50 acrss 20dB AGC range 13. 14. Oscillatr stability Oscillatr phase nise 15. Acquisitin time At 1 KHz At 10 KHz At 100 KHz Lw charge pump current 60 50 80 60 ppm ±50 dbc/hz ms -57-82 -100 120 0 C -60 C ambient temperature withut transmissin n SDA/SCL High charge pump 60 current CSO dbc 50 full spectrum f carriers at 16. Intermdulatin +75dBµV each, AGC set CTB dbc 50 fr 15dB gain reductin 17. IF utput level dbµv 111 balanced 18. IF bandwidth MHz 8 19. IF accuracy khz ±74 Nte1: Amplitude respnse may increase by 1dB, if vltage gain is reduced by 20dB. PRELIMINARY SPECIFICATION Page: 10/20
7.2 Antenna Lp Thrugh N Parameters Unit Min Typ Max Remarks 1. Frequency range MHz 47 858 2. Pwer Gain at TV ut db -1 3 3. Nise Figure at TV ut db 6 8,5 4. Return lss at TV ut db 6 5. Oscillatr leakage at TV ut <300MHz >300MHz dbµv 15 26 Antenna Input terminated with 75Ω 6. Islatin at TV ut/if ut 90 t 860MHz db 25 Test signals with same levels at ANT in and TV ut 7. 8. Islatin TV ut / ANT in Linearity at TV ut CSO CTB db 20 db db 57 61 In accrdance t CENELEC 50083-7 PRELIMINARY SPECIFICATION Page: 11/20
8 Applicatin Infrmatin 8.1 Tuner Write Data MSB LSB Address Byte 1 1 0 0 0 MA1 MA0 0 A Prg. Divider Byte 1 0 n14 n13 n12 n11 n10 n9 n8 A Prg. Divider Byte 2 n7 n6 n5 n4 n3 n2 n1 n0 A Cntrl Byte 1 1 CP 0 0 x RSA RSB 0 A Cntrl Byte 2 x x x x x x P1 P0 A CP Charge pump current CP=0 : I = 50uA (recmmended fr best phase nise perfrmance) CP=1 : I = 250uA Prgrammable Divider (Byte1 and Byte2) Divider rati: ( MHz) ( KHz) FOSC N = FREF with: N = 16384 N14 + 8192 N13 + 4096 N12 +... + 4 N 2 + 2 N1+ N 0 Address MA1 MA0 Vltage at Pin 8 C0 0 0 (0...0,1) * Vcc1 C2 0 1 pen circuit C4 1 0 (0,4...0,6) * Vcc1 C6 1 1 (0,9...1) * Vcc13 Cntrl Inf Byte1 Cntrl Inf Byte2 RSA RSB fref/min tuning step 1 1 62,5 KHz X 0 50,00 KHz 0 1 31,25 KHz Fsc P1 P0 [ 87 ~ 185 ] MHz 1 0 [ 185 ~ 465 ] MHz 0 1 [ 465 ~ 894 ] MHz 0 0 na 1 1 Nte: Fr infrmatin regarding general specificatin f I2C bus see datasheet f the IC CP3550 frm INFINEON. PRELIMINARY SPECIFICATION Page: 12/20
9 Electrstatic discharge 9.1 Test Each DUT must be capable f nrmal perfrmance fllwing its subjectin t the fllwing tests: MIL STD 883C HBM Test is perfrmed with a vltage discharge frm a 100 PF capacitr ver a 1500 Ω series resistance in the discharge path. There is a direct cntact between the test prbe head and the unit under test, using the test pints and cnditins detailed belw: Test t pins 1 thrugh 13 : 3 successive ESD discharges f ± 2 KVDC between each pin and the DUT frame. IEC 1000-4-2 Test is perfrmed with a vltage discharge frm a 150 PF capacitr ver a 330 Ω series resistance in the discharge path. There is a direct cntact between the test prbe head and the unit under test, using the test pints and cnditins detailed belw: Test fr antenna input scket ± 8 KVDC Test fr antenna utput scket ± 5 KVDC 9.2 Handling Anyne handling a Unit must wear a prperly grunded anti - static discharge bracelet t minimize ESD damage. After each Unit is aligned and tested, it will be packed with anti - static ply fam r material prir t transprtatin and strage. This prtective fam is t remain in place until the frnt-end is assembled and sldered nt the receiver main bard. PRELIMINARY SPECIFICATION Page: 13/20
10 Reliability test prcedure & cnditins Nte: Rm temperature = 25 C ± 2 C 10.1 Heat lad test Measure the DUTs at rm temperature Lad the DUTs int chamber f the fllwing cnditins: Temperature = 60 C Perid = 500 hrs Cycle = 1,5 hrs n; 0,5 hrs ff Quantity = 10 pcs Cl-dwn 0,5 hr at rm temperature, then measured the DUTs within 1 hr The test shall be cntinued t 1000 cycles fr infrmatin nly 10.2 Humidity lad test Measure the DUTs at rm temperature Lad the DUTs int chamber f the fllwing cnditins: Temperature = 40 ± 5 C Perid = 24 hrs Cycle = cnstantly n Quantity = 20 pcs Cl-dwn 0.5 hr at rm temperature, then measured the DUTs within 1 hr Lad the DUTs again int chamber f the fllwing cnditins: Temperature = 40 ± 5 C Humidity = 90 t 95 % Perid = 500 hrs Cycle = 1,5 hrs n; 0,5 hrs ff Quantity = 20 pcs Cl dwn 0.5 hr at rm temperature, then measured the DUTs within 1 hr PRELIMINARY SPECIFICATION Page: 14/20
10.3 Cld test Measure the DUTs at rm temperature Lad the DUTs int chamber f the fllwing cnditins: Temperature = - 20 ± 5 C Perid = 500 hrs Cycle = cnstantly n Quantity = 10 pcs Warm up fr 2 hrs at rm temperature, then measured the DUTs within 1 hr 10.4 Thermal shck Measure the DUTs at rm temperature Lad the DUTs int chamber f the fllwing cnditins: Temperature Perid Pwer Quantity = - 25 C fr 60 min 85 C fr 60 min = 200 cycles = pwer ff = 10 pcs Cl-dwn 0,5 hr at rm temperature then measured the DUTs within 1 hr 10.5 Temperature cycle test Measure the DUTs at rm temperature Lad the DUTs int chamber f the fllwing cnditins: Temperature Perid Cycle Quantity = -5 C fr 16 hrs then 60 C fr 8 hrs = 500 hrs = cnstantly n = 10 pcs Cl dwn 0.5 hr at rm temperature, then measured the DUTs within 1hr Lad the DUTs again int chamber f the fllwing cnditins: Temperature = 40±5 C Humidity =90 t 95% Perid = 500 hrs Cycle = 1,5hrs n; 0,5hrs ff Quantity = 10 pcs Cl dwn 0.5 hr at rm temperature, then measured the DUTs within 1hr PRELIMINARY SPECIFICATION Page: 15/20
10.6 Vibratin test (per FR-M-202 f Thmsn Green Bk, Vibratin test) Frequency: 3,5 Hz Vertical amplitude: 15 t 25 mm Duratin: 1 hr Quantity : 1 cartn 10.7 Drp test (per FP-M-204 f Thmsn Green Bk, Drp test) Packaged apparatus: < r = 50 kg Height: depend n weight per FP-M-204 1 crner + 3 edges + 6 faces Drp n the weakest crner (pint G) Drp n the shrtest edge in cntact with pint G Drp n average edge in cntact with pint G Drp n the lngest edge in cntact with pint G Drp flat wise n the side f minimum surface Drp flat wise n the side f ppsite minimum surface Drp flat wise n the side f average surface Drp flat wise n the side f ppsite average surface Drp flat wise n the side f maximum surface Drp flat wise n the side f ppsite maximum surface Quantity: 1 cartn 10.8 Life test Measure the DUTs at rm temperature Lad the DUTs int chamber f the fllwing cnditins: Temperature = 60 C Perid = 500 hrs Cycle = cnstantly n Quantity = 20 pcs Cl dwn 0.5 hr at rm temperature, then measured the DUTs within 1 hr PRELIMINARY SPECIFICATION Page: 16/20
11 Appendix 11.1 Packaging Tuner Cartn Bx PALLET (BIG) 1. TYPE Crrugated Paper Bx wd 2. QUANTITY TUNERS 1 65 5200 CARTONS 1 80 3. WEIGHT 50g 4Kg 340Kg (Apprximate) 4. DIMENSIONS L x H x D (in mm) 63 x 35.25 x 14.2 469 x 396 x 64 1200 x 1450 x 800 PRELIMINARY SPECIFICATION Page: 17/20
11.2 Identificatin / Trace ability Packaging Label DCT 7042A TOCOM NO. : 21415800 QTY. : 65 PCS CTN. NO. : Tuner Label DCT 7042A 21415800 21140100043 Frmat Y-WW-D-II-NNNNN e.g 2-11-4-01-00043 Nte: Y : Year Prduced WW : Week Prduced D : Day f the week Prduced II : Current Index NNNNN : Running number f the tuner PRELIMINARY SPECIFICATION Page: 18/20
11.3 Applicatin Circuit RF-AGC (0.1-4V) (I2C) SCL SDA AS Vt (33V) 1n 10k 2 X 100R 10k 1n NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 3x100nF 3x1uH t ADC 100n Vcc +5 V IF AGC (0.1-2V) PRELIMINARY SPECIFICATION Page: 19/20
12 Revisin Date f Changes Index Mdificatin 07-10-04 00 Preliminary Specificatin. (MOPLL CP3550) all 27-05-05 A Include new mdel DCT7046 and DCT7047 5,6 Pages PRELIMINARY SPECIFICATION Page: 20/20