ANCHORS - ADHESIVE AC100E Professional Kits Adhesive value pack for the professional has all the required accessories for post installed chemical anchors, this easy to handle all-in-one kit keeps all your adhesive accessories protected and easily accessible. Contained in a Durable Carry Case is the perfect Starter Kit for adhesive anchoring. 4 tubes of AC100E with all cleaning equipment, tooling and instruction leaflet ensure you will get the job done correctly. Powers AC100E polyester resin with no VOC is GECA approved, perfect for use on projects with Green Star requirements. Part Number Description 1 x Dispensing Gun 4 x Tubes of AC100e 1 Blow Pump 6 x Nozzles 4 x Metal Brushes 1 x Instruction Sheet 428 Fasteners - Adhesive Anchoring-Concrete & Masonry Polyester, Vinyl ester, Epoxy adhesive injection systems. Glass adhesive capsules containing two part epoxy resins. Threaded Studs for adhesive anchoring in zinc plated, galvanised and stainless steel materials 8mm to 24mm diameters in varied lengths. AC100E.CASE
ANCHORS - ADHESIVE AC100E Professional Kits Adhesive value pack for the professional has all the required accessories for post installed chemical anchors, this easy to handle all-in-one kit keeps all your adhesive accessories protected and easily accessible. Contained in a Durable Carry Case is the perfect Starter Kit for adhesive anchoring. 4 tubes of AC100E with all cleaning equipment, tooling and instruction leaflet ensure you will get the job done correctly. Powers AC100E polyester resin with no VOC is GECA approved, perfect for use on projects with Green Star requirements. Part Number Description 1 x Dispensing Gun 4 x Tubes of AC100e 1 Blow Pump 6 x Nozzles 4 x Metal Brushes 1 x Instruction Sheet 428 Fasteners - Adhesive Anchoring-Concrete & Masonry Polyester, Vinyl ester, Epoxy adhesive injection systems. Glass adhesive capsules containing two part epoxy resins. Threaded Studs for adhesive anchoring in zinc plated, galvanised and stainless steel materials 8mm to 24mm diameters in varied lengths. AC100E.CASE
ANCHORS- MASONRy Close to edge installs The Blue-Tip SCREWBOLT anchor cuts a thread into the base material. With no expansion forces, it can be installed closer to the edge than traditional mechanical anchors - no base material damage. Removable and reusable Easy to remove, leaving a neat clean hole. Unlike traditional anchors no grinding off of anchors is needed and no anchor components are left in the hole. It can be reused in the same hole. Immediate high strength loading Blue-Tip SCREWBOLT Anchors can be loaded immediately. Unlike adhesive anchors, there is no lengthy curing time. This allows for immediate completion of fastening applications. Shallow embedment Blue-Tip SCREWBOLT installs at shallower depths than traditional sleeve anchors reducing chances of striking rebar or cables. Drilling time and bit wear can be reduced resulting in significant savings. Fasteners - Mechanical Concrete & Masonry Anchors Light and Medium duty expansion anchors in varied head styles and materials. Nylon, zinc plated and galvanised carbon steel, stainless steel from 5mm to 10mm diameters. High-Tensile 5.8 and 8.8 grade Safety Anchors 10mm to 14mm bolt diameter range. Blue Tip ScrewBolts-concrete and masonry thread cutting concrete screw anchors in Zinc and Galvanised finish from 5.5mm to 16mm diameters in varied lengths. HEX HEAD - Carbon Steel Yellow Passivated Part Number Size Part Number Size BT550 5 x 50mm BT1060 10 x 60mm BT6530 6.5 x 30mm BT1075 10 x 75mm BT6550 6.5 x 50mm BT10100 10 x 100mm BT6575 6.5 x 75mm BT10120 10 x 120mm BT65100 6.5 x 100mm BT1275 12 x 75mm BT850 8 x 50mm BT12100 12 x 100mm BT860 8 x 60mm BT12150 12 x 150mm BT875 8 x 75mm BT16100 16 x 100mm BT8100 8 x 100mm BT16150 16 x 150mm Other Blue-Tip SCREWBOLT styles available in the range: Countersunk Eyebolt Mechanically Galvanised Hex Blue-Tip SCREwBOLT The Blue-Tip SCREWBOLT anchor is a one piece, heavy duty anchor with either a finished hex head or countersunk flat head. Easy to identify the Blue-Tip SCREWBOLT anchor also has many unique features and benefits that make it well suited for almost every application. Optimum performance is obtained using a combination of patented design concepts. The benefit to the designer is higher load capacities while the benefit to the user is ease of installation. Features: ratchet teeth for locking to fixture relief grooves for low installation torque providing dust extraction reverse parabolic threads provide high load capacity 30 helix angle allows it to be tightened quickly chamfered tip for easy centering East identification Blue-Tip SCREWBOLT anchors have both the diameter and length clearly embossed on the head of the anchor. This enables simple and easy inspection. Concrete, Block, Brick The Blue-Tip SCREWBOLT anchor is versatile and can be used in a variety of base materials. This reduces the need to stock assorted anchor types. BREMBOLT Bremick Brembolt Load Controlled Sleeve Anchors are heavy duty, one piece, torque controlled mechanical anchors, consisting of a high tensile threaded plow bolt and washer, a hardened cold formed cone with a heavy gauge carbon steel shear sleeve and nylon compression ring. Suitable for use in cracked and uncracked concrete, ETA Approved, Shock loading approved, Fire Rated and approved for use in Tilt Wall construction AS 3850. Masonry Screw Anchor The Bremick Masonry Screw Anchor is a highly versatile anchor providing the combined performance characteristics of mechanical anchors and those of chemical anchors, with the added benefit of being totally removable. Manufactured in one piece from high tensile steel it is capable of providing secure anchorage into concrete, hollow brick, block, stone and even timber. Suitable for installation at close centres and small edge distances. 429
ASSORTMENT KITS FASTENERS Sleeve Anchor Bremick Sleeve Anchors are available in a broad range of styles for medium duty applications, including, flange head, flush head, countersunk, hook, eye and suspension styles. Bremick Sleeve anchors are also available in a full range of materials including Stainless steel 316, Galvanised and zinc plated. Trade Packs Sturdy plastic box with clear lid 10 Compartment plastic storage box FASTENERS Through Bolt Bremick Through h Bolts are a single unit preassembled wedge type anchors available in zinc plate, galvanised and 316 stainless steel. Bremick through bolts are suitable for high load applications in concrete where through fastening, long thread lengths and small diameter drill holes are important. Drop In Anchor Bremick Drop In Anchors are medium m duty deformation controlled anchors for use in concrete where a flush internal threaded fixing is required. Bremick drop in anchors are available lipped to ensure flush setting to the concrete surface. Materials include Stainless steel 316 and zinc plated. 650 piece SPLIT PINS 10 sizes Metric - 1.6 x 22 mm to 4.0 x 45 mm Imperial - 7/64 x 50 mm & 9/64 x 50 mm Part Number: 102.110 720 piece Spring & internal star washers. 10 sizes Metric - M5 to M12 Part Number: 102.120 650 piece Flat steel washers. 10 sizes Metric - M5 to M12 Imperial - 3/16 to 1/12 Part Number: 102.130 750 piece Phillips drive pan head self tapper screws 8 sizes 6G x 1/2 to 12G x 1 Imperial - 3/16 to 1/12 Part Number: 102.135 650 piece Hexagon nuts. 7 sizes Metric - M3 to M12 Part Number: 102.150 145 piece Hexagon bolts. 10 sizes Metric - M5 x 12 mm to M10 x 70 mm Part Number: 102.155 575 piece Machine screw & hexagon nut Machine Screws: 7 sizes M4 x 16 mm to M6 x 40 mm Hexagon Nuts: 3 sizes M4, M5 & M6 Part Number: 102.276 ANCHORS - MASONARy - SySTEMS 430 BREMFIX The Bremfix Chemical anchoring systems comprise of a full range of adhesive anchoring products including, Bremfix Capsules, Bremfix Poly Injection, Bremfix StyFree EASF Injection and Bremfix Epoxy Injection Systems. Also available are high tensile stud bolts, Stainless steel 316 stud bolts, masonry sieves and cleaning tools. Master Packs Sturdy plastic box with clear lid Removable inserts 2825 piece Machine screws, nuts and washers Part Number: 102.534 1490 piece Self tapper assortment pack Part Number: 102.512 1395 piece Washer assortment Part Number: 102.567
BOLTS - PETROCHEMICAL FASTENERS - STAINLESS STEEL Petrochemical Stud Bolts Bremick manufactures and stocks a full range of certified stud bolts for the petrochemical industry all of which are conveniently packaged with two Heavy Hex. Nuts. Stud bolts, Hexagonal Headed Bolts and Heavy Hex Nuts from 1/2 diameter to 4 Diameter. Lengths up to 12ft. Grades, all grades. Coatings, all specified coatings available. All products are supplied with full certification. BOLTS & NuTS - HEX HEAD Stainless s Steel A comprehensive range of Stainless Steel Grade 316 and Stainless Steel Grade 304 fasteners are readily available for all fastening applications that are exposed to highly corrosive environments. Metric, UNC and BSW Bolts, Set Screws, Threaded Rod and Socket Screws are readily available. Also Self Tapping Screws, Metal Thread Screws, Nuts, Acorn Nuts, and Nyloc nuts. Mild Steel Bremick Mild Steel fasteners are manufactured in strict conformance with Australian Standards. Our range includes: Metric and BSW Bolt and Nuts, Metric and BSW Set Screws, Metric and BSW Cup Head Bolts, Coach Screws, Threaded Rods and a broad range of Nuts and Washers. Available in a full range of coatings including plain, zinc plated and galvanised. fasteners - forced entry powder & gas High Tensile Bremick High Tensile fasteners are used where high strength connections are paramount. Our range includes, UNC Grade 5, UNC Grade 8, UNF Grade 5, UNF Grade 8 and Metric Class 8.8 Nuts and Bolts, Set Screws and Threaded Rod. Plain, zinc plated and galvanised finishes are all readily available. Structural Assemblieses Bremick manufactures a full range of Structural Assemblies, all of which fully comply to AS 1252 for use in structural steel work. Each assembly consists of bolt, nut and hardened washer. Also available are Direct Tension Indicating Washers that make it possible to accurately and economically control bolt tension. Full conformance certification provided with all purchases. Fasteners - Forced Entry Powder and Gas Fasteners - Forced Entry Powder and Gas actuated drive pin systems for Concrete, Masonry and Steel. 27 caliber powder explosive tools. Gas fuel cell functioning tools for most trades with consumable concrete pins and trade specific fastening solutions. 431
NuTS & washers SCREwS Nuts and washers Bremick provides a full range of nuts and washers to meet all fastening needs. Nuts are available in all forms, all grades and with all thread forms, including locking nuts, nyloc nuts and wing nuts. Washers are also available in al sizes, grades, coatings and Stainless steel grades 316 and 304, including flat round, square and spring washers. RIVETS - POP Self Tapping Screws & Metal Threads The Bremick range of Metal Thread and Self Tapping Screws are available in either stainless Steel Grade 304 or Stainless steel Grade 316. Countersunk and Pan Head Metal Thread Screws are also available with metric or imperial thread forms up to M8 or _. Self Tapping screws are available in sizes from 4g to 14g SCREwS - COACH - HEX HEAD FASTENERS Rivets The Bremick Rivet offering is the largest in Australia and is available in a variety of packaging options, Bulk Cartons, Plastic Trade Packs or Retail Packs. Roofing and cladding rivets are available in a full range of pre painted colours. Other rivets include Marine grade aluminium 5056 and 5052, Stainless Steel, Steel and monel rivets. SCREw & RIVETING SOLuTIONS Coach Screws For secure fastening of heavy timbers the Bremick range of Coach Screws cover all application needs. Sizes available range from 6mm up to 20mm in diameter, with length from 25mm to 200mm. Bremick Coach Screws are also available to suit any corrosive environment with the choice of, zinc plated, galvanised and stainless steel grades 316 and 304. SCREwS - ROOFING VORTEX Roof VORTEX Roof is a universal screw engineered for steel roofing applications and is highly suitable for fastening both corrugated and square rib roofing profiles to timber, metal battens and steel purlins. Fully compliant with AS 3566 and is available in a full range of pre painted colours. 432 Self Drilling Screws for Metal & Timber Carbon Steel Self Drilling Screws for Metal and Timber in yellow zinc and class 4 finish. Type 17, Needle point, Chipboard and specialist decking screws. Bi-Metal 304 and 316 stainless steel self-drilling screws for metal. Tamper resistant self drilling screws in carbon and stainless steel materials for metal and timber. Muro stand up auto feed collated Screw driving system for ergonomic, cost effective screw fastening. Riveting solutions - general purpose, blind, sealed, truss, countersunk head, alum, steel, stainless steel, Monel and specialist rivets variants and all tooling. VORTEX Cyclone VORTEX Cyclone is a universal roofing assembly specifically engineered to withstand the most severe tropical cyclone and is suitable for fastening corrugated and square rib roofing profiles to timber, metal battens and steel purlins. Extensively tested and approved to Building Codes of Australia (BCA) 2008 specifications B 1.2 for use in buildings in cyclonic regions. Available in all colours.
SCREwS - SELF DRILLING SCREwS - SOCKET General Purpose Screws Whatever the application Bremick can provide the solution with a purpose made self drilling screw. For use in metal, timber, chipboard, treated pine, plasterboard or fibre cement, Bremick has the right screw. All fully compliant with Australian Standard AS 3566 Socket Screws Bremick provides a full range of Socket Screws in Carbon Steel, Stainless Steel Grade 316 and Stainless Steel Grade 304. Cap Screws, Flat Head counter Sunk, Button Head, Shoulder Screws and Grub Screws. THREADED ROD Self Drill l Screws for Metal Bremick manufactures a full range of, AS 3566 compliant,self drilling screws for metal applications including a comprehensive range of roofing and cladding screws. Metal drilling screws are available in zinc plate, AS 3566 Class 4 Galvanised, AS 3566 Class 3 galvanised or Stainless Steel. Roofing and cladding screws are also available, pre painted in all common roofing colours. Threaded Rod The Bremick range of Threaded Rod is readily available in all grades and thread forms in both metric and imperial. All of which is manufactured in compliance with international standards. Stainless Steel Grade 316 and 304. Mild Steel and High Tensile grades in: black, zinc plated and galvanised. Threads BSW,UNC, UNF and Metric. Lengths: 3ft, 12ft, 1m and 3m. Accessories: Nuts, washers, square washers and couplers. THREAD INSERTS Type 17 Screws Bremick manufactures a full range of, AS 3566 compliant, Type 17 self drilling screws for general fastening into timber including a comprehensive range of T17 roofing and cladding screws. Type 17 screws are available in zinc plate, AS 3566 Class 4 Galvanised, AS 3566 Class 3 galvanised or Stainless Steel. Roofing and cladding screws are also available, pre painted in all common roofing colours. wire Thread Insert System M2 M12 (1/8" 1/2") PowerCoil Thread Repair Kits include all the necessary components to successfully repair damaged threads. Kits include Drill, STI Tap, Inserts, Installation Tool and Tang Break-Off Tool. The PowerCoil Wire Thread Insert System includes a complete range of over 140 Thread Repair Kits; Free Running and Screw Locking inserts; Strip Feed Inserts; STI Hand & Machine Taps; Installation, Tang Break and Removal Tools. Stainless s Steel Screws For fastening applications ions in highly corrosive environments Bremick carries a broad range of self drilling stainless steel screws in both grade 304 and 316. Metal Drilling Screws Type 17 screws Decking screws Bugle Batten screws Self tapping screws and many more 433
THREAD RESTORERS PowerCoil Nes Adjustable Thread Restorers PowerCoil NES External and Internal thread restorers are ideal for simple, cost effective thread repair in maintenance, plumbing, construction, car repair and agricultural applications. PowerCoil NES hand tools automatically adjust to any thread diameter and pitch, can be used on left hand or right hand thread, both inch and metric with no need to measure the thread. PowerCoil NES External thread restorers are available in 3 sizes and can repair threads from 4mm (5/32") up to 128mm (5"). PowerCoil NES Internal thread restorers are available in 6 sizes and can repair threads from 8mm (5/16") up to 68mm (2-5/8"). PowerCoil NES restorers are available individually or in a range of convenient combination sets. FASTENERS washers - direct tension - structural Direct Tension Indictors Direct Tension Indicating Washers (DTI`s) are used with Bremick Structural Assemblies to ensure that the bolts are installed to the correct bolt tension as specified in the Australian Standard for Structural Steel (AS 4100). Bremick DTI`s are fully calibrated to and provide a simple and economic method to assist accurate installation and inspection of structural bolted connections. Bremick DTI`s are manufactured from Grade 8.8 steel, are galvanised and conform to ASTM F 959M and AS 4100. 434