OC9665R0TX Sewing Table-White Assembly Instruction For assistance with assembly contact: Southern Enterprises Inc. Customer Service 1-800-633-5096 service@seidal.com www.seidal.com
OC9665R0TX Sewing Table-White Parts List Please review all parts and hardware before disposing of any packaging. Call Customer Service if missing hardware. Do not return to store/retailer. Using a screw that is too long will cause damage. Before beginning assembly, separate each type of screw. Carefully study the screw diagrams below. You may receive extra hardware with your unit. A B C Left Wood Top Leaf Panel Upper Shelf D E Of 21 F Lower Shelf Large Shelf Back Panel G H I Leaf Support Right Side Panel Left Side Panel J K L Divider Bottom Front Stretcher Top stretcher
1 Of 28 2 1 3 1 Wood Dowel 8*30mm 4 Of 2 Cam Bolt 6.8*36mm 5 2 Cam Lock 15*12 6 2 Cover Large-Machine-screw1/4*2mm T-Bolt 7 Of 2 8 Of 2 9 Of 4 Unlocking Caster Locking Caster Small-Machine-screw M5 10 Of 4 11 2 12 Of 4 Screw Nut M5 Wood Screw 3*22mm Hinge 13 2 11 2 Small-Machine-screw M4 Screw Nut M4 Care and Cleaning Instructions: Before using, wipe with a clean, dry cloth. Periodically apply furniture wax to renew the finish. Avoid rubbing or scratching the surface with rough or abrasive objects. For replacement parts or questions, please call Customer Service at 1-800-633-5096. Do not return product to store. Please call manufacturer for assistance, questions or parts. Assembly Tool Required No.2 Phillips Screwdriver
OC9665R0TX Sewing Table-White Assembly Instruction Step 1: Put all parts on a soft surface to prevent scratches Tighten wood screws(11) through hinges(12) into predrilled holes on underside of large top panel and leaf panel(a,b) as shown. Step 2: Insert wood dowel(1) into predrilled hole on bottom edge of divider(j) and fit into corresponding hole on lower shelf(d). Insert T-bolt(6) into predrilled hole on divider(j), and tighten large machine screw(5) through predrilled hole on lower shelf(d) into T-bolt(6). Please note that if screw does not tighten of T-bolt are facing screw, then slide upper shelf(c) into groove on diver (J) as shown.
Step 3: Insert wood dowels(1)into predrilled holes on holes on edges of parts(c,d,j) and fit into corresponding holes on right side panel(h).insert T-bolts(6) into the holes on parts(c,d,j) and tighten large machine screw(5) through predrilled holes on right side panel(h) into T-bolts(6). Please note that if screws do not tighten, rotate T-bolts(6) so that threads of T-bolt are facing screw as shown. Step 4: Insert wood dowels (1) into predrilled holes on large shelf(e) and fit into corresponding holes on back panel(f). Insert T-bolt(6) into predrilled hole on underside of large shelf(e), and tighten large machine screw(5) through predrilled hole on back panel(f) into T-bolt(6). Please note that if screw does not tighten, rotate T-bolt(6) so that thread of T-bolt are facing screw as show. Attach cam bolt (2) to large shelf (E). Insert wood dowels(1)into predrilled holes on large shelf(e), and fit into corresponding holes on bottom front stretcher(l)
Step 5: Fit casters (7,8) on bottom edge on side panel (H,I) by using small machine screws (9) and screw nuts (10) Insert wood dowels (1) into predrilled holes on the inside of side panel (H,I) and fit into corresponding holes on ends of large shelf (E), bottom front stretcher(l),top stretcher(k) and back panel(f). Insert T-bolts(6)into the holes on parts(e,f) and tighten large machine screw(5) through predrilled holes on left side panel(i) into T-bolts(6).Please note that if screws do not tighten, rotate T-bolts(6) so that threads of T-bolts are facing the screws. Assemble tight side panel(h) in same manner as shown. Insert wood screws (13) through hinges(12) by using screw nut(14). And tighten into predrilled holes on leaf support (G) and outside of left side panel (I), then set the unit upright as shown..
Step 6: Insert wood dowels(1) and can-bolts(2) into predrilled holes on underside of parts(a,b) and fit into corresponding holes on top edges of parts(h,i,j,k). Insert cam-locks(3) into big holes on parts(h,i,j,k) with slot for screwdriver facing outward. Rotate cam-locks(3) clockwise to secure cam-bolts(2). Push covers(4) into cam-locks(3) as shown.
Parts Replacement Form Customer Information Name Address City/State/Zip Code Phone Number Please indicate where you purchased this item: Store/Website/Catalog Please indicate color/size/style number: Style No Parts Letter Parts Description Needed Please immediately examine this product carefully. Any request for missing parts or damage replacement must be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and we are not responsible for any damages due to product modification(s). If damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise. Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am 4pm Mon-Fri Central time if you have product issues or email us at service@seidal.com. Please ask for customer service representative for issues involving damages or replacement parts. Please ask for technical assistance representative for any issues with product and assembly/construction. Please contact the retailer that you purchased from for returns. Customer Service 1-800-633-5096 service@seidal.com Southern Enterprises, Inc.