Schedule B Technical Specifications Gujarat Energy Transmission Corporation Limited Year 2015-17 E-2472
Content 1. General Guidelines for Sourcing of Fabric.02 2. Fabric Specifications.....03 3. List of Fabric Defects.27 4. Specifications for Packing.28 5. Distribution of Uniform.. 29 6. Designs of Uniform (Design sketch of Fabric Pack)... 30 E-2472 1
General Guidelines for Sourcing of Fabrics 1. Fabric samples along with shade band and lab dips have to be approved prior to bulk production. 2. The shade band and lab dips will have to be approved before the commencement of fabric production. The shade will be matched visually. Any shade variation, from the approved shade will not be acceptable. 3. Test report will have to be attached along with samples. 4. All testing should be carried out by an independent accredited agency nominated by GETCO. 5. Lot wise Test report for the mentioned parameter will have to be submitted before dispatch of fabric 6. Fabric will be in the form of packed cut pieces as per specifications of Fabric pack No. 1/2/3 (Each applicable for the respective product) 7. No fabric defect of any nature is permissible in the fabric pack, refer Annexure No. 1 8. Fabric has to comply with all the mentioned test standards 9. Packing is as per the Annexure No. 2 10. Each Fabric Pack must be traceable to the lot Number. 11. Shade variation within the same piece is strictly unacceptable. 12. The fabric will be accepted only after a pre dispatch inspection by an independent accredited agency nominated by GETCO 13. Any other guideline that might be laid down to ensure the best quality of fabric /garment/ trim/accessory being procured. 14. All types of Fabric designs are available at office of the CE(Project), Gujarat Energy Transmission Corporation Limited, 8 th Floor, Sardar Patel Vidyut Bhavan, Race Course Circle, Vadodara, Gujarat. E-2472 2
GETCO- Staff Uniform: Specifications for Fabric Sourcing Fabric Specification Fabric pack: 1 Fabric code: TR-2-PC Garment type : Category of staff : Length of fabric: Trim/ accessory: Sketch of Design Formal trouser Style No. FT-01 ADM./TECHNICAL 5.00 mts per pack Nil Yes Fabric Swatch S. No. Name of Company Color code 1 GETCO FT-01 Page 1.1of 3 E-2472 F 3
GETCO- Staff Uniform: Specifications for Fabric Sourcing Fabric pack: 1 Fabric code: TR-2-PC Fabric specification Standard No. Tolerance Type PC suiting Content/ composition 65% polyester, 35%Cotton AATCC-20/20A +/- 2% Weave Twill EPI (Finished) 126 +/- 2.5% ASTM-D-3775 PPI (Finished) 68 +/- 2.5% Yarn count Warp 2/40s Weft 2/40s IS:3442 Yarn Type Blended with polyester Warp fiber/ intimate blend Blended with polyester Weft fiber/ intimate blend AATCC-20/20A Width 58 or 149 cm +/- 1 c.m. Weight in gms per sqm (GSM) 263 ASTM D - 3776 +/- 2% Tensile strength Warp 119 kg (Minimum) Grab method ISO-5081 Weft 63 kg (Minimum) 4 x6 Tear strength Warp 4900 gm (Minimum) Weft 2646 gm (Minimum) ASTMD 1424 Page 1.2of 3 E-2472 F 4
GETCO- Staff Uniform: Specifications for Fabric Sourcing Fabric pack: 1 Fabric code: TR-2-PC Fabric should confirm following quality standards: Tests Test Method Acceptable standard Fastness to sun light AATCC-16 4 Washing AATCC-61-2003 4 Colour fastness Crocking AATCC-8 4 Heat press AATCC-133 4 Perspiration AATCC-15-2002 4 Dimensional stability AATCC 135- (After 3 cycles) 2003 2% Bow/ skew ASTM D 3882 2% Shade Abrasion, 10000 cycles ASTM D 4966 change 4 Pilling 4 Washing shrinkage % Length 2% (Max) IS 63301A Width 1% Note: Banned dyes / chemicals not to be used Value for test results: 5: Negligible 4: Slight 3: Noticeable 2: Considerable 1: Sever Page 1.3of 3 E-2472 F 5
GETCO- Staff Uniform: Specifications for Fabric Sourcing Fabric pack: 2 Garment type: Category of staff : Formal Shirt Class I & II (Male) Class III & IV (Non-Tech) Length of fabric : Trim/ accessory: Sketch of Design 6.60 mtr per pack Nil Yes S. No. Name of company Color code 1 GETCO As per Sample Page 2.1of 3 E-2472 F 6
GETCO- Staff Uniform: Specifications for Fabric Sourcing Fabric pack: 2 Fabric specifications Standard No. Tolerance Type ETI Content/ composition 35% polyester, 65%Cotton Weave Plain EPI (Finished) 130-150 +/- 2% PPI (Finished) 60-70 +/- 2% 40s Micro Polyester Warp Fibre, Blended with cotton Fibre / intimate +/- 3% Yarn count Blend 40s Micro Polyester Weft Fiber, Blended with cotton Fiber / intimate Blend +/- 3% Yarn Type Warp 65%cotton:35% Polyester Blend +/- 3% Weft 65%cotton:35% Polyester Blend +/- 3% Width 58 or 149 cm +/- 2% Weight in gms per sqm (GSM) 130 ASTM D - 3776 +/- 5% Tensile strength Warp 46 kg (Minimum) ASTM D 5034 Grab Method strip size 20x5 cms Weft 23 kg (Minimum) ASTM D 5034 Tear strength Warp 1548 gm (Minimum) ASTM-D-1424 Weft 1274 gm (Minimum) ASTM-D-1424 Seam Slippage Warp Wt 19.8 kg Weft Wt No slim slippage ASTM D 434 Page 2.2 of 3 E-2472 F 7
GETCO- Staff Uniform: Specifications for Fabric Sourcing Fabric pack: 2 Fabric should confirm following quality standards: Tests Test Method Acceptable standard Fastness to sun light AATCC-16 3.5 Washing @ 49 0 C (Color Change) AATCC-61-2A 4 Water @ 37 0 C (Color Colour fastness Change) AATCC-107 4 Dry Rub AATCC - 8 4 Wet Rub AATCC 8 3 Heat press AATCC 133 4 Perspiration AATCC-15 4 Dimensional stability (After 3 cycles) AATCC 135-2003 +/- 1% Bow/ skew ASTM D 3882 2% Martindale Abrasion Abrasion Rev No Thread Break ASTM D 4966 Resistance (min) >19000 Note: 1. Banned dyes / chemicals not to be used 2. The Fabric should satisfy following criteria Wrinkle Free Perspiration absorbance should be high Low level of Dullness in color after washing Value for test results: 5: Negligible 4: Slight 3: Noticeable 2: Considerable 1: Sever Page 2.3of 3 E-2472 F 8
GETCO- Staff Uniform: Specifications for Fabric Sourcing Fabric pack: 3 Garment type : Category of staff : Work Shirt Class III & IV (Tech.) Length of fabric : 6.6 mtrs per pack Trim/ accessory: Retro reflecting piping 10 Mts. Sketch of Design Yes S. No. Name of company Color code 1 GETCO As per Sample Page 3.1of 3 E-2472 F 9
GETCO- Staff Uniform: Specifications for Fabric Sourcing Fabric pack: 3 Fabric specifications Standard No. Tolerance Type ETI Content/ composition 35% polyester, 65%Cotton Weave Plain EPI (Finished) 130-150 +/- 2% PPI (Finished) 60-70 +/- 2% 40s Micro Polyester Warp Fibre, Blended with cotton Fibre / intimate +/- 3% Yarn count Blend 40s Micro Polyester Weft Fiber, Blended with cotton Fiber / intimate Blend +/- 3% Yarn Type Warp 65%cotton:35% Polyester Blend +/- 3% Weft 65%cotton:35% Polyester Blend +/- 3% Width 58 or 149 cm +/- 2% Weight in gms per sqm (GSM) 130 ASTM D - 3776 +/- 5% Tensile strength Warp 46 kg (Minimum) ASTM D 5034 Grab Method strip size 20x5 cms Weft 23 kg (Minimum) ASTM D 5034 Tear strength Warp 1548 gm (Minimum) ASTM-D-1424 Weft 1274 gm (Minimum) ASTM-D-1424 Seam Slippage Warp Wt 19.8 kg Weft Wt No slim slippage ASTM D 434 Page 3.2of 3 E-2472 F 10
Fabric pack: 3 Fabric should confirm following quality standards: Tests Test Method Acceptable standard Fastness to sun light AATCC-16 3.5 Washing @ 49 0 C (Color Change) AATCC-61-2A 4 Water @ 37 0 C (Color Colour fastness Change) AATCC-107 4 Dry Rub AATCC - 8 4 Wet Rub AATCC 8 3 Heat press AATCC 133 4 Perspiration AATCC-15 4 Dimensional stability (After 3 cycles) AATCC 135-2003 +/- 1% Bow/ skew ASTM D 3882 2% Martindale Abrasion Abrasion Rev No Thread Break ASTM D 4966 Resistance (min) >19000 Note: 3. Banned dyes / chemicals not to be used 4. The Fabric should satisfy following criteria Wrinkle Free Perspiration absorbance should be high Low level of Dullness in color after washing Value for test results: 5: Negligible 4: Slight 3: Noticeable 2: Considerable 1: Sever Page 3.3of 3 E-2472 F 11
ANNEXURE 1 List of Fabric Defects Nature Yarn Defects Weaving Defects Defects Broken Filaments, Color flecks, Slubs, Knots Broken Ends, Broken Ends Woven in a Bunch, Broken Pattern, Double End, Float, Gout, Hole-Cut or Tear, Lashing-in, Local Distortion, Missing Ends, Oil or other Stain, Oily or Soiled Ends, Oily Weft, Reed Marks, Selvedge Defect, Slough Off, Smash, Snarls, Stitches, Untrimmed Loose threads, Weft Bar, Weft Crack. Processing Defects Bleaching spot, Blurred or Dark Patch, Defects caused by Hanging Thread, Dye Bar, Dyestuff Stain Misprint/Absence of Print, Patchy or Streaky or Uneven Dyeing, Pilling, Shading or Listing, Uneven Printing or Tinting, Water Mark, White Spot. Embroidery Defects Wrong Placement, Tilting of Embroidery, Broken threads, Incomplete embroidery, Shade Variation. Visual Defect Any visual defect that may affect, salability, serviceability, appearance of the fabric in a way that is significantly unacceptable for sale. E-2472 F 12
Specifications for packing: ANNEXURE 2 1. Pack should contain one pc. Of fabric length, sketch of design, trim etc. as mentioned in fabric Pack No.: 1 to 8 2. Ready Pack size 12 x10 ( +/- ½ ) 3. Material: Self adhesive poly bag, gauge: 200 4. Necessary warning should be printed in front side of bag to keep it away from the reach of children. 12 Warning This bag is not a toy. Keep it away from the reach of children This side up Sticker Hole Pack No: 16 font Fabric code: 14 font Colour code: 14 font Lot no: 12 font Sort No.: 12 font 10 E-2472 F 13
Design sketch of Fabric Packs E-2472 F 14
E-2472 F 15
E-2472 F 16