SHOOTING BENCH OWNERS MANUAL & USAGE INSTRUCTIONS INCLUDES BENCH MODELS: AR02-B The Deluxe Shooting Bench AR03-B The Swivel Action Shooting Bench
AR02-B DELUXE SHOOTING BENCH WARNING: Do not use without inserting mounting pin (under platform) into hole in rear leg. (see fig. ) Keep fingers away from pivot point between back and front legs to prevent pinching. STEP. Using the front leg-lower piece and front leg-upper piece, assemble the front leg. Secure with (2) flange bolts and tighten securely. NOTE: The front leg support brace and seat support brace should be on the same side of the assembly. (see fig. ) STEP 2. Attach shooting platform to front leg assembly by inserting pivot axle through holes in platform and tube on front leg assembly. NOTE: To insure proper alignment, the shooting platform should rest on same side as both support braces. Fasten with (2) /2" nylock nuts. (see fig. ) STEP 3. Slide the rear leg-upper piece around the front leg assembly. Attach rear leg-lower piece. Secure with (2) flange bolts; tighten securely. (see fig. ) STEP 4. Secure legs together by inserting the 3/8" x 5 7/8" bolt and (2) steel washers through the top hole of each leg. NOTE: One washer should be placed between rear leg-upper piece and bolt. Other washer should be placed between rear leg-upper piece and nut. Fasten with 3/8" nylock nut; tighten securely. NOTE: To insure proper alignment when bench is upright, leg support braces should both be facing upward. (see fig. ) STEP 5. Stand bench up using special care to insure that mounting pin (welded under the platform) is inserted into hole in rear leg. (see fig. ) STEP 6. Using (4) flange bolts, attach swivel assembly to seat cushion. (see fig. ) STEP 7. Insert swivel assembly through /2" Id bushing, hole on seat support and other /2" Id bushing. Secure with /2" nylock nut. Then, attach seat support to the bench using seat pin. NOTE: Three holes are provided for an adjustable seat position. STEP 8. Thread 3/8" stop nut onto the gun rest-upper piece and the /2" stop nut onto the gun rest-lower piece. Then, thread the upper piece and lower piece together forming the complete gun rest. Insert the entire assembly into shooting platform. (see fig. ) STEP 9. Attach shooting platform cover and enjoy your shooting bench. FOR FLAT STORAGE: Remove seat support by pulling pin. Pull up on shooting platform to disengage the mounting pin, and fold legs flat. Reinsert seat support and push pin through all holes to stabilize. Parts List (AR02-B) Part # UP0-0578 UP0-0579 UP0-0580 UP0-058 UP0-0582 UP0-0583 UP0-0584 UP0-0585 UP0-0586 UP0-0587 UP0-0588 UP0-0589 UP0-0590 UP77-000 UP77-0050 UP77-005 UP77-0055 UP77-002 UP77-0054 UP77-0063 UP77-0062 UP77-0053 Description Shooting Platform Front Leg-Lower Front Leg-Upper Rear Leg-Lower Rear Leg-Upper Seat Cushion Seat Support Qty Swivel Assembly Gun Rest-Upper Gun Rest-Lower Pivot Axle Platform Cover Instruction Manual /4" x 5/8" Flange Bolt 3/8" x 5 7/8" Bolt 3/8" Nylock Nut /2" Nylock Nut Seat Pin 3/8" Wing Nut 8 3 /2" Wing Nut /2" Id Bushing 2 Steel Washer 2 2
AR02-B FIGURE Gun Rest-Upper Gun Rest-Lower Shooting Platform Mounting Pin Pivot Axle Rear Leg-Upper Steel Washer Seat Cushion Steel Washer Seat Support Brace Swivel Assembly Front Leg-Upper Rear Leg Support Brace Rear Leg-Lower Seat Pin Seat Support Front Leg-Lower Front Leg Support Brace 3
AR03-B SWIVEL ACTION SHOOTING BENCH STEP. Using the outer holes on the hub assembly attach the legs using (3) 5/6" x 2 /4" hex bolts [C] and (3) 5/6" nylock nuts. Next, using the inner holes of the hub assembly insert (3) snap pins underneath the legs. (see fig. ) STEP 2. Insert the mainframe into the hub assembly. Then, insert the platform connectors into the horizontal tube on the mainframe. (see fig. ) STEP 3. Next, connect the shooting platform to the platform connectors using (2) /4" flange nuts. (see fig. ) STEP 4. Attach the platform support to the shooting platform using () 5/6" x 7/8" hex bolt [B] and () 5/6" nylock nut. Then, connect the opposite end of the platform support to the mainframe using () snap pin. (see fig. ) STEP 5. Next, attach the seat cushion to the seat support using (3) /4" x 7/8" hex bolts [A]. Then, connect the seat support to the mainframe using () 5/6" x 2 3/4" hex bolt [D] and () 5/6" nylock nut. (see fig. ) NOTE: Three holes are provided in mainframe for an adjustable seat height. STEP 6. Thread 3/8" wing nut onto the gun rest-upper piece and the /2" wing nut onto the gun rest-lower piece. Then, thread the upper piece and lower piece together forming the completed gun rest. Thread the entire assembly into shooting platform. (see fig. ) NOTE: Gun rest may be adjusted for height and direction to accommodate personal preference. STEP 7. Attach the platform cover to the shooting platform. NOTE: The shooting platform lock on the mainframe can be adjusted for optimal stability. FOR EASY TRANSPORT: Snap pins may be removed from platform support and hub assembly to allow the bench top and legs to be folded flat. Reinsert snap pins for secure storage until next use. Parts List (AR03-B) Part # Description Qty UP0-059 UP0-0592 UP0-0593 UP0-0594 UP0-0595 UP0-0596 Shooting Platform Mainframe Hub Assembly Inner Hub Assembly Bushing Seat Support Leg 3 UP0-0649 Platform Support UP0-0650 Seat Cushion UP0-0597 Platform Connector 2 UP0-0586 Gun Rest-Upper UP0-0587 Gun Rest-Lower UP0-0598 Platform Cover UP0-0590 Instruction Manual UP77-0022 UP77-0040 UP77-0044 UP77-0047 UP77-0007 UP77-0029 [A] /4" x 7/8" Hex Bolt [B] 5/6" x 7/8" Hex Bolt [C] 5/6" x 2 /4" Hex Bolt [D] 5/6" x 2 3/4" Hex Bolt /4" Flange Nut 5/6" Nylock Nut UP77-0054 3/8" Wing Nut UP77-0063 /2" Wing Nut 2 UP77-003 5/6" x 4" Snap Pin 2 8 3 4
AR03-B FIGURE Gun Rest-Upper Gun Rest-Lower Shooting Platform B Platform Connectors Seat Cushion Mainframe Snap Pin Platform Support A A A Seat Support Snap Pin C D C Snap Pin C Hub Assembly Inner Hub Assembly Bushing *this is placed inside hub assembly during manufacturing. You should not need to assemble this. Snap Pin Leg Leg Leg 5
STANDARD LIMITED WARRANTY Warranty: BGHA, Inc. warrants all Big Game Hunting Accessories treestands or climbing system products to be free from defects in material and workmanship for a period of twelve months from the original date of retail purchase. BGHA, Inc. warrants the enclosed hardware (where applicable) is delivered to be free from physical defects for a period of twelve months from the original date of retail purchase. Repair Procedures, Exclusive Remedy: BGHA, Inc. will at its option, repair, or replace products not conforming to this limited warranty at no charge. THIS IS THE SOLE AND EXCLUSIVE REMEDY AVAILABLE FOR BREACH OF WARRANTY OR UNDER ANY OTHER LEGAL THEORY WITH RESPECT TO BIG GAME HUNTING ACCESSORIES PRODUCTS. If you find a product to be defective, contact the customer service department at 800-268-5077. When you receive authorization, return the product as directed at your expense. Product repairs not covered by warranty, and product updates, will be provided at a set rate. Limitations: This warranty is void if the product is damaged by improper or abnormal use or by accident; if the product is altered or modified in any way other than those directed by official Big Game Hunting Accessories instructions; or if any attempt is made to repair the product without authorization from BGHA, Inc. It is solely the purchaser s responsibility to determine the suitability of these products for each particular application. Big Game Hunting Accessories products are intended for hunting and hunting only. Big Game Hunting Accessories are in all events not suitable, and are not authorized, for use in any situations that might pose potentially injurious to life and health, other than those situations that the products are intended for. This warranty is not assignable or transferable. No Other Warranties: EXCEPT AS PROVIDED IN THIS LIMITED WARRANTY SET FORTH IN THE WARRANTY CARD SUPPLIED WITH REMINGTON TREESTANDS AND INSTRUCTION SHEETS ARE PROVIDED AS IS. ALL OTHER WARRANTIES AND REPRESENTATIONS, ORAL OR WRITTEN, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED AND DO NOT APPLY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HERE OF. Except as required by law, no representative, agent, or employee of BGHA, Inc. is authorized to make warranties, representations, or obligations inconsistent with, or in addition to, those set forth in this limited warranty. No Damages: IN NO EVENT WILL BGHA, INC. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF WARRANTY OR UNDER ANY LEGAL THEORY, even if advised of the possibility of such damages. In no event will BGHA, Inc. be liable for sums in excess of the purchase price of the product. BGHA, Inc. is thus not liable for lost profits or goodwill; downtime; damage or destruction of items or equipment used with, or in conjunction with, BGHA, Inc.; personal injury or loss; or any other damages. General: (a) This agreement is the entire agreement between you and BGHA, Inc.; supersedes any prior or different agreements, representations, or proposals; and may be changed only by written agreement with BGHA, Inc. (b) Waiver by any party of any default or breach of this agreement will not constitute a waiver of any subsequent default or breach of the same or different kind. (c) The invalidity of any provision of this agreement shall not affect the validity of the other provisions hereof. (d) This agreement shall be governed by the laws of the State of Minnesota, U.S.A.
To activate your product s warranty, please mail in your registration card or submit it online at www.biggametreestands.com PRODUCT REGISTRATION Product Purchased Model Number Serial Number Owner s Name Street Address City State Zip Code Email Address Phone Owner s Age (optional) Sex (optional) Male Female Date Purchased Purchased From (Dealer Name) How did you hear about us: Catalog Webpage Friend Magazine Other, please explain Are you a: Bow Hunter Gun Hunter Both Treestand Preference: Fixed Position Climbing Ladderstand REGISTRATION INFORMATION Although Big Game Treestands are manufactured with the highest standards, regular maintenance is required for the up-keep of your product. Regular maintenance is the responsibility of the consumer. If at any time there is a defect with any part of your treestand, we insist that you replace the part prior to using the stand. Improper or incorrectly performed maintenance or repair, including the use of unauthorized replacement parts, will void all warranties. Replacement parts may be ordered on our website at www.biggametreestands.com or by calling our Customer Service Department at 800-268-5077. OWNER S RECORD Product Name Model Number Serial Number Purchase Date Purchased From (Dealer Name) Keep the OWNER S RECORD for your reference. YOU MUST RETURN THE COMPLETED REGISTRATION CARD WITHIN (30) DAYS OF THE PURCHASE IN ORDER TO ACTIVATE THE LIMITED WARRANTY COVERAGE. (Make sure to include date purchased on the card!)
PO Box 382 820 North Redding Avenue Windom, MN 560 Toll Free: 800-268-5077 www.biggametreestands.com