Order #xxxxx - P20 - Ben Jamin - General Layout Step Page of 8
Order #xxxxx - P20 - Ben Jamin - Backwall Assembly Step Part Number 1 2 3A 3 4 Description Left w/ A10 Clamps Attached Middle Upper Curved Vertical w/ A10 Clamps Attached Upper Curved Vertical 23 w Horizontal Step 1 NOTE: When assembling horizontals they should be placed approximately one inch from TOP and BOTTOM. 4 Slide horizontal into groove Assure that a good connection is made and tighten to secure. Step 1: NOTE: Can be assembled either face down on floor then lifted upright or upright as shown in drawings. A) Connect vertical leg assemblies [1 and 2] together by connecting horizontal extrusions [4] between assemblies tightening BLACK knobs on backside of extrusion making sure Velcro faces toward BACK and placing it about one inch up from bottom and tightening. B) Connect vertical extrusions [3 and 3A] to leg assemblies [1 and 2] using vertical connection bar as shown. C) Connect upper horizontal extrusion [4] between verticals [3 and 3A] placing it about one inch down from top. 3A 3 NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully engage, gently rock lock and extrusion while turning knob until lock fully opens. Rear View of Display 1 Vertical Connection Bar 2 Slide Connection Bar into lower leg assembly. Slide upper vertical over bar and secure both. Step stool may be required for assembly. STAR indicates location of knobs on BACKSIDE of unit. Black Knob 4 Turn Knob Clockwise to Tighten Lock Page of 8
Order #xxxxx - P20 - Ben Jamin - Backwall Assembly cont d Step 2 Part Number 5 6 7 8 Description Right Upper Curved Vertical 69 w Horizontal w/ Hinge Facing UP 69 w Horizontal w/ Hinge Facing DOWN Step 2 4 NOTE: When assembling horizontals they should be placed approximately one inch from TOP and BOTTOM. Slide horizontal into groove Assure that a good connection is made and tighten to secure. Step 2: NOTE: Can be assembled either face down on floor then lifted upright or upright as shown in drawings. A) Connect vertical extrusion [6] to leg assembly [5] using vertical connection bar as shown. B) Connect horizontal extrusions [7 and 8] between vertical assemblies by tightening BLACK knobs on backside of extrusion making sure Velcro faces toward BACK. NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully engage, gently rock lock and extrusion while turning knob until lock fully opens. 3A 3 8 6 Rear View of Display 1 2 Slide Connection Bar into lower leg assembly. Slide upper vertical over bar and secure both. STAR indicates location of knobs on BACKSIDE of unit. 5 Black Knob Turn Knob Clockwise to Tighten Lock 4 Hinge Extrusion Top Horizontal Hinge faces down. Bottom Horizontal Hinge faces up. 7 Page 2 of 8
Order #xxxxx - P20 - Ben Jamin - Backwall Assembly (Cont d) Step Part Number 9 10 11 12 Description Middle Upper Curved Vertical 69 w Horizontal w/ Hinge Facing UP 69 w Horizontal w/ Hinge Facing DOWN Step 3 NOTE: When assembling horizontals they should be placed approximately one inch from TOP and BOTTOM. Slide horizontal into groove Assure that a good connection is made and tighten to secure. Step 1: NOTE: Can be assembled either face down on floor then lifted upright or upright as shown in drawings. A) Connect vertical extrusion [10] to leg assembly [9] using vertical connection bar as shown. B) Connect horizontal extrusions [11 and 12] between vertical assemblies by tightening BLACK knobs on backside of extrusion making sure Velcro faces toward BACK. 6 12 NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully engage, gently rock lock and extrusion while turning knob until lock fully opens. 10 Slide Connection Bar into lower leg assembly. Slide upper vertical over bar and secure both. Step stool may be required for assembly. Rear View of Display 5 Vertical Connection Bar STAR indicates location of knobs on BACKSIDE of unit. 9 Black Knob Turn Knob Clockwise to Tighten Lock Hinge Extrusion Top Horizontal Hinge faces down. Bottom Horizontal Hinge faces up. 11 Page of 8
Order #xxxxx - P20 - Ben Jamin - Backwall Assembly (Cont d) Step Part Number 13 14 15 Description Right w/ A10 Clamps Attached Upper Curved Vertical w/ A10 Clamps Attached 23 w Horizontal Step 4 NOTE: When assembling horizontals they should be placed approximately one inch from TOP and BOTTOM. Slide horizontal into groove Assure that a good connection is made and tighten to secure. 12 Step 2: NOTE: Can be assembled either face down on floor then lifted upright or upright as shown in drawings. A) Connect vertical extrusion [14] to leg assembly [13] using vertical connection bar as shown. B) Connect horizontal extrusions [15] between vertical assemblies by tightening BLACK knobs on backside of extrusion making sure Velcro faces toward BACK. NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully engage, gently rock lock and extrusion while turning knob until lock fully opens. 6 10 15 13 Rear View of Display 5 Slide Connection Bar into lower leg assembly. Slide upper vertical over bar and secure both. STAR indicates location of knobs on BACKSIDE of unit. Black Knob 9 14 11 Turn Knob Clockwise to Tighten Lock 15 Page of 8
Order #xxxxx - P20 - Ben Jamin - Blade and Wing Assembly Step 5 Decorative Blade Attachment (if accidently removed) Slide A10 Clamp into groove of square extrusion. A10 When desired location is found, tighten set screw to secure. Attach decorative wing and blades to A10 s attached to Backwall as shown. Set- Screw Tighten black plastic set screw to secure Wing in place. Black Plastic Set-screw Hex Key Tool Flathead Screwdriver (if necessary) Page 5 of 8
Order #xxxxx - P20 - Ben Jamin - Header, Shelf and Cubby Assembly Step 6 Accessary Attachment Attach Header support to Backwall then attach header to support by Velcroing it. Header Light Connection Attach Lights to Backwall where desired and tighten in place. Header Accessary Attachment Header Cubby Attachment Shelf attaches to section 5 by setting atop pins located on right side and securing into place with thumbscrew on left. Shelf attaches to back of sections 1 and 2 by setting atop pins located on back left side. Pins Slide onto back pin first. Thumbscrew When attaching counter you will need to first slide shelf onto back pin then set down on front pin. Page 6 of 8
Order #xxxxx - P20 - Ben Jamin - Workstation Assembly - Qty. 2 Step Part Number A B C D Description Left Right Horizontal Extrusion Horiontal Extrusion w/ Door Stopper Step 1: A) Connect lower horizontal extrusion [C] between bottom of leg assemblies [A and B] as shown. B) Insert Laminated infill into grooves of leg assemblies [A and B]. C) Attach extrusion door between leg assemblies [A and B] and atop laminated infill. D) Attach upper horizontal extrusion w/ door stopper [D] between leg assemblies [A and B], and set flush with top of legs [A and B]. D (w/ Door Stopper) Knobs face INSIDE of workstation NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully engage, gently rock lock and extrusion while turning knob until lock fully opens. DOOR A (left) B (right) Knobs face INSIDE of workstation Pins are located on INSIDE FRONT vertical of Leg Assemblies Laminated Infill Black Knob C Knobs face FORWARD Turn Knob Clockwise to Tighten Lock Align with bottom of leg assemblies [A and B]. Page of 8
Order #xxxxx - P20 - Ben Jamin - Workstation Assembly cont d Step 8 Part Number E F Description Horizontal Extrusion Horizontal Extrusion Step 2: A) Attach horizontal extrusion [E] between vertical leg assemblies [A and B] as shown below. B) Insert Laminated infill into grooves of vertical leg assemblies [A and B]. C) Attach upper horizontal extrusion [F] between vertical leg assemblies [A and B] atop infill. D) Place internal shelf into assembled pedestal atop pins. E) Set Counter atop assembled pedestal and secure with Velcro straps attached to underside of top. Knobs face INSIDE of workstation F Place internal shelf into workstation then place counter atop assembled workstation. Internal Shelf Laminated Infill Knobs facing FORWARD E Page 8 of 8
Order #xxxxx - P20 - Ben Jamin - Backwall Case Packing - 6 Total Cases Case #1 - Backwall Components Cutout for A10 Clamp Vertical Connection Bar Cutout for A10 Clamp Top View of each Level A10 s Attached Horizontal Extrusion Header Supports Horizontal Extrusion Vertical Connection Bar Blade Wing Horizontal Extrusions Wing Attachment Header Level 5 Cutout for A10 Clamp Level 4 Vertical Connection Bar Level 3 Level 2 Level 1
Order #xxxxx - P20 - Ben Jamin - Backwall Case Packing - 6 Total Cases Case # 2 - Backwall Components Cutout for A10 Clamp Vertical Connection Bar Cutout for A10 Clamp Top View of each Level A10 s Attached Horizontal Extrusion Horizontal Extrusion Vertical Connection Bar Blade Wing Horizontal Extrusions Header Wing Attachment Level 4 Cutout for A10 Clamp Cutout for A10 Clamp Level 3 Level 2 Level 1
Order #xxxxx - P20 - Ben Jamin - Backwall Case Packing - 6 Total Cases Case #3 - Backwall Components Top View of each Level Backside Shelf Wings and Header Cubby Level 2 Level 1
Order #xxxxx - P20 - Ben Jamin - Backwall Case Packing - 6 Total Cases Case # 4 - Backwall Components Top View of each Level Backside Shelf Wings and Header Cubby Level 2 Level 1
Order #xxxxx - P20 - Ben Jamin - Workstation Case Packing - 6 Total Cases Case # 5 -Workstation Components Top View of each Level Connection Bar for Verticals Horiz. Extrusion E A Horiz. Extrusion F B Internal Shelf Inserts Horiz. Extrusion C Horiz. Extrusion D Door Counter Level 5 Level 4 Level 3 Level 2 Level 1
Order #xxxxx - P20 - Ben Jamin - Workstation Case Packing - 6 Total Cases Case # 6 - Workstation Components Top View of each Level Connection Bar for Verticals Horiz. Extrusion E A Horiz. Extrusion F B Internal Shelf Inserts Horiz. Extrusion C Horiz. Extrusion D Door Counter Level 5 Level 4 Level 3 Level 2 Level 1