EE C245 - ME C218 Introduction to MEMS Design Fall Today s Lecture

Similar documents
EE C245 - ME C218 Introduction to MEMS Design Fall Today s Lecture

PROBLEM SET #7. EEC247B / ME C218 INTRODUCTION TO MEMS DESIGN SPRING 2015 C. Nguyen. Issued: Monday, April 27, 2015

Surface Micromachining

AN INTEGRATED MICROELECTROMECHANICAL RESONANT OUTPUT GYROSCOPE

Mechanical Spectrum Analyzer in Silicon using Micromachined Accelerometers with Time-Varying Electrostatic Feedback

EE C245 ME C218 Introduction to MEMS Design

RF Micro/Nano Resonators for Signal Processing

Digitally Tuned Low Power Gyroscope

EE C245 ME C218 Introduction to MEMS Design Fall 2007

Lecture 10: Accelerometers (Part I)

EE C245 ME C218 Introduction to MEMS Design

INF 5490 RF MEMS. LN10: Micromechanical filters. Spring 2012, Oddvar Søråsen Department of Informatics, UoO

EE C245 ME C218 Introduction to MEMS Design

The Design of 2.4GHz Bipolar Oscillator by Using the Method of Negative Resistance Cheng Sin Hang Tony Sept. 14, 2001

Wafer Level Vacuum Packaged Out-of-Plane and In-Plane Differential Resonant Silicon Accelerometers for Navigational Applications

Reference Diagram IDG-300. Coriolis Sense. Low-Pass Sensor. Coriolis Sense. Demodulator Y-RATE OUT YAGC R LPY C LPy ±10% EEPROM TRIM.

Micromechanical Circuits for Wireless Communications

INF 5490 RF MEMS. L12: Micromechanical filters. S2008, Oddvar Søråsen Department of Informatics, UoO

MEMS Reference Oscillators. EECS 242B Fall 2014 Prof. Ali M. Niknejad

Miniaturising Motion Energy Harvesters: Limits and Ways Around Them

Introduction to Microeletromechanical Systems (MEMS) Lecture 12 Topics. MEMS Overview

Non-linear frequency noise modulation in a resonant MEMS accelerometer

EE C245 ME C218 Introduction to MEMS Design

INF 5490 RF MEMS. LN10: Micromechanical filters. Spring 2011, Oddvar Søråsen Jan Erik Ramstad Department of Informatics, UoO

Integrated Dual-Axis Gyro IDG-1215

Reconfigurable 4-Frequency CMOS Oscillator Based on AlN Contour-Mode MEMS Resonators

CRYSTAL oscillators are widely used to generate precision

Integrated Dual-Axis Gyro IDG-1004

A Vacuum Packaged Surface Micromachined Resonant Accelerometer

Designing a 960 MHz CMOS LNA and Mixer using ADS. EE 5390 RFIC Design Michelle Montoya Alfredo Perez. April 15, 2004

RF MEMS for Low-Power Communications

Design of Temperature Sensitive Structure for Micromechanical Silicon Resonant Accelerometer

RFIC DESIGN EXAMPLE: MIXER

ISSCC 2006 / SESSION 16 / MEMS AND SENSORS / 16.1

K-BAND HARMONIC DIELECTRIC RESONATOR OS- CILLATOR USING PARALLEL FEEDBACK STRUC- TURE

Integrated Dual-Axis Gyro IDG-500

VIBRATING mechanical tank components, such as crystal. High-Order Medium Frequency Micromechanical Electronic Filters

MICRO YAW RATE SENSORS

EE C245 ME C218 Introduction to MEMS Design Fall 2010

A Doubly Decoupled X-axis Vibrating Wheel Gyroscope

ETI , Good luck! Written Exam Integrated Radio Electronics. Lund University Dept. of Electroscience

Michael S. McCorquodale, Ph.D. Founder and CTO, Mobius Microsystems, Inc.

EE12: Laboratory Project (Part-2) AM Transmitter

PART MAX2605EUT-T MAX2606EUT-T MAX2607EUT-T MAX2608EUT-T MAX2609EUT-T TOP VIEW IND GND. Maxim Integrated Products 1

Semiconductor Detector Systems

A Self-Sustaining Ultra High Frequency Nanoelectromechanical Oscillator

A HIGH FIGURE-OF-MERIT LOW PHASE NOISE 15-GHz CMOS VCO

Lab 4. Crystal Oscillator

The steeper the phase shift as a function of frequency φ(ω) the more stable the frequency of oscillation

System Level Simulation of a Digital Accelerometer

In order to suppress coupled oscillation and drift and to minimize the resulting zero-rate drift, various devices have been reported employing indepen

MEMS Technologies and Devices for Single-Chip RF Front-Ends

Index. bias current, 61, 145 critical, 61, 64, 108, 161 start-up, 109 bilinear function, 11, 43, 167

Dr.-Ing. Ulrich L. Rohde

Vibrating MEMS resonators

Last Name Girosco Given Name Pio ID Number

Noise Reduction in Transistor Oscillators: Part 3 Noise Shifting Techniques. cross-coupled. over other topolo-

MEMS-FABRICATED ACCELEROMETERS WITH FEEDBACK COMPENSATION

MEMS Real-Time Clocks: small footprint timekeeping. Paolo Frigerio November 15 th, 2018

A Real-Time kHz Clock Oscillator Using a mm 2 Micromechanical Resonator Frequency-Setting Element

IN-CHIP DEVICE-LAYER THERMAL ISOLATION OF MEMS RESONATOR FOR LOWER POWER BUDGET

77 GHz VCO for Car Radar Systems T625_VCO2_W Preliminary Data Sheet

CMOS-Electromechanical Systems Microsensor Resonator with High Q-Factor at Low Voltage

Behavioral Modeling and Simulation of Micromechanical Resonator for Communications Applications

EVALUATION KIT AVAILABLE 10MHz to 1050MHz Integrated RF Oscillator with Buffered Outputs. Typical Operating Circuit. 10nH 1000pF MAX2620 BIAS SUPPLY

easypll UHV Preamplifier Reference Manual

Symmetrical and decoupled nickel microgyroscope on insulating substrate

Low-Power Ovenization of Fused Silica Resonators for Temperature-Stable Oscillators

6.776 High Speed Communication Circuits and Systems Lecture 14 Voltage Controlled Oscillators

EE C245 ME C218 Introduction to MEMS Design

Low Cost 100 g Single Axis Accelerometer with Analog Output ADXL190*

High-Q and Wide Dynamic Range Inertial MEMS for North-Finding and Tracking Applications

Lab 4. Crystal Oscillator

Evaluating and Optimizing Tradeoffs in CMOS RFIC Upconversion Mixer Design. by Dr. Stephen Long University of California, Santa Barbara

Electrically coupled MEMS bandpass filters Part I: With coupling element

SP 22.3: A 12mW Wide Dynamic Range CMOS Front-End for a Portable GPS Receiver

Phase Noise Modeling of Opto-Mechanical Oscillators

PYKC 7 Feb 2019 EA2.3 Electronics 2 Lecture 13-1

Wafer-level Vacuum Packaged X and Y axis Gyroscope Using the Extended SBM Process for Ubiquitous Robot applications

Quadrature GPS Receiver Front-End in 0.13μm CMOS: The QLMV cell

Understanding VCO Concepts

THE rapid growth of portable wireless communication

Differential Amplifier : input. resistance. Differential amplifiers are widely used in engineering instrumentation

Micro-nanosystems for electrical metrology and precision instrumentation

Receiver Architecture

Switch-less Dual-frequency Reconfigurable CMOS Oscillator using One Single Piezoelectric AlN MEMS Resonator with Co-existing S0 and S1 Lamb-wave Modes

Vibrating RF MEMS for Low Power Wireless Communications

High Performance, Wide Bandwidth Accelerometer ADXL001

6.976 High Speed Communication Circuits and Systems Lecture 11 Voltage Controlled Oscillators

AN MSI MICROMECHANICAL DIFFERENTIAL DISK-ARRAY FILTER. Dept. of Electrical Engineering & Computer Science, University of Michigan, Ann Arbor, USA 2

ISSCC 2006 / SESSION 11 / RF BUILDING BLOCKS AND PLLS / 11.9

OBSOLETE. High Accuracy 1 g to 5 g Single Axis imems Accelerometer with Analog Input ADXL105*

High Accuracy 1 g to 5 g Single Axis imems Accelerometer with Analog Input ADXL105*

Communication Systems. Department of Electronics and Electrical Engineering

Frequency-Selective MEMS for Miniaturized Low-Power Communication Devices. Clark T.-C. Nguyen, Member, IEEE. (Invited Paper)

Micro and Smart Systems

Piezo-Ceramic Glossary

Optoelectronic Oscillator Topologies based on Resonant Tunneling Diode Fiber Optic Links

i. At the start-up of oscillation there is an excess negative resistance (-R)

High-Q UHF Micromechanical Radial-Contour Mode Disk Resonators

Transcription:

EE 45 ME 8 Introduction to MEMS Design Fall 003 Roger Howe and Thara Srinivasan Lecture 6 Micromechanical Resonators I Today s Lecture ircuit models for micromechanical resonators Microresonator oscillators: sustaining amplifiers, amplitude limiters, and noise Resonant inertial sensors: accelerometers and gyroscopes

Reading/Reference List. T.. Nguyen, h.d. Thesis, Dept. of EES, U Berkeley, 994. T. A. Roessig, R. T. Howe, A.. isano, and J. H. Smith, Surfacemicromachined resonant accelerometer, Transducers 97, hicago, Ill., June 69, 997, pp. 85986. A. A. Seshia, R. T. Howe, and S. Montague, An integrated microelectromechanical resonantoutput gyroscope, IEEE MEMS 00, Las egas, Nevada, January 00. net lecture. T.. Nguyen, Transceiver frontend architectures using vibrating micromechanical signal processors, Topical Meeting on Silicon Monolithic Integrated ircuits in RF Systems, Sept. 4, 00, pp. 33. J. Wang, Z. Ren, and. T.. Nguyen, Selfaligned.4 GHz vibrating radialmode disk resonator, Transducers 03, Boston, Mass., June 8, 003, pp. 947950. B. Bircumshaw, et al, The radial bulk annular resonator: towards a 50Ω RF MEMS filter, Transducers 03, Boston, Mass., June 8, 003. M. U. Demirci, M. A. Abdelmoneum, and. T.. Nguyen, Mechanically cornercoupled square microresonator array for reduced series motional resistance, Transducers 03, Boston, Mass., June 8, 003, pp. 955958.. Kaaakari, et al, Squareetensional mode singlecrystal silicon micromechanical RFresonator, Transducers 03, Boston, Mass., June 8, 003, pp. 89894. 3 ombdrive Lateral Resonator Anchor connects ground plane and resonator Typical bias: I O 0 D voltage across drive and sense electrodes to resonator. T.. Nguyen, h.d. Thesis, EES Dept., U Berkeley, 994 4

The Lateral Resonator as a Twoort. T.. Nguyen, h.d. Thesis, EES Dept., U Berkeley, 994 5 Input urrent Input current i t is the derivative of the charge q v D dv i t v dt d dt D D The capacitance has a D component and a timevarying component due to the motion of the structure t o m m t t linearized case t Substitute to find the input current: vd t I v t v t 6 3

4 7 Input Motional Admittance Y w hasor form of the motional current i : I Y The displacementtovoltage ratio can be reepressed in terms of the drive force F d The input motional admittance inverse of impedance is the ratio of the phasor motional current to the ac drive voltage: X I F F X Y d d F F X Y d d 8 Input Admittance ont. The electrostatic force component at the drive frequency is: t v t v t f D d, The mechanical response of the resonator is Lecture 9: F d F X d The input admittance is: I

Series LR Admittance The current through an LR branch is: I L I / o R o L R Match terms in motional admittance find equivalent elements 9 Equivalent ircuit for Input ort A series LR circuit results in the identical epression find equivalent values L,, and R m L η η k km R η Qη electromechanical coupling coefficient I o L R At resonance, the impedances of the inductance and the capacitance cancel out I R 0 5

6 Output ort Model onsider first the current due to driving the input set v 0 t t t i In phasor form, / / Q k X I o o I and I are related by the forward current gain φ : I I φ model by a currentcontrolled current source Twoort Equivalent ircuit v 0 L R o I φ I 0 I

omplete Twoort Model I L L I o φ I φ I o R R Symmetry implies that modeling can be done from port, with port shorted superimpose the two models 3 Equivalent ircuit for Symmetrical Resonator f f. T.. Nguyen, h.d., U Berkeley, 994 4 7

455 khz ombdrive Resonator alues L assumes vacuum not small huge! mindboggling!. T.. Nguyen, h.d., U Berkeley, 994 5 DoubleEnded Tuning Fork Resonators i 0 urrent through structure more resistance decreases Q more feedthroughto substrate T. Roessig, h.d.,me, U Berkeley, 997 6 8

Ideal Tuning Fork Twoort Response hase change of 80 o at resonance pins the frequency, with drifts in the feedback amplifier having little effect Response assumes no feedthroughcapacitance between input and output ports T. Roessig, h.d.,me, U Berkeley, 997 7 Tuning Fork Response with apacitive Feedthrough f Feedthroughcapacitance results in a null in the amplitude response and an added sense current which increases with frequency and which can obscure the resonance entirely! R int drive v d int f R eq L eq eq o o structure node R int int i s Net lecture: f and its control sense T. Roessig, h.d.,me, U Berkeley, 997 8 9

Microresonator Oscillator. T.. Nguyen and R. T. Howe, IEEE J. SolidState ircuits, 34, 440454 999. 9 urrenttooltage or Transresistance Amplifier R f i in i 0 v out The feedback resistor can be implemented using a MOSFET biased in the triode region 0 0

Microresonator Oscillator Schematic Transresistance amplifier:. T.. Nguyen and R. T. Howe, IEEE J. SolidState ircuits, 34, 440454 999. Integrated 6.5 khz Microresonator Oscillator MOS with tungsten metallization olysi lateral resonator. T.. Nguyen and R. T. Howe, IEEE J. SolidState ircuits, 34, 440454 999. Erratic chaotic behavior observed for high D biases in this and other MEMS oscillators was later eplained by Kim Turner h.d. ornell, 999, now USB

ierce Oscillator Schematic crystal doubleended tuning fork Advantage over transr configuration: A. A. Seshia, et al, MSM0, San Juan, uerto Rico 3 TuningFork Oscillator Neararrier Spectrum ierce Topology output power dbc/hz Measured rmsnoise thermal electronic noise A. A. Seshia, et al, IEEE MEMS0. frequency 0 5 Hz 4

Differential Resonant Accelerometer Inertial force is coupled from a proof mass through a leverage system to two DETF oscillators in a pushpull manner tension compression T. Roessig, h.d.,me, U Berkeley, 997 5 Leverage Mechanism DETF oscillators are etremely stiff to forces along their length, which makes mechanical amplification feasible In the ideal case of a perfect pivot, Archimedes F out / F in r in / r out T. Roessig, h.d.,me, U Berkeley, 997 6 3

Resonant Accelerometer erformance Fractional RA measures instability of an oscillator as a function of integration time. RA min 6 0 8 at τ sec for 70 khz DETF oscillators f min 0.004 Hz. Sensitivity 45 Hz/g a min 90 µg T. Roessig, h.d.,me, U Berkeley, 997 7 ResonantOutput Rate Gyroscope frame suspension outer frame direction of motion tuning fork oscillator proof mass oscillator lever arm tuning fork oscillator F c Ω z z fied free y drive fleure sense direction A. A. Seshia, h.d. Thesis EES Dept., U Berkeley May 00 8 4

ResonantOutput Gyro: Mechanical Element reference resonator proof mass fleure tuning fork force sensor tuning fork force sensor proof mass error correction outer frame selftest electrodes lever arm A. A. Seshia, et al, IEEE MEMS0. 9 ResonantOutput Gyroscope Die Shot Tuning Fork Drive Electronics roof Mass Drive Electronics Mechanical Structure 4.5 mm z y A. A. Seshia, et al, IEEE MEMS0. Sandia IMEMS MEMSfirst process 30 5

Sideband Modulation by oriolis Force Oscillator output power dbm A. A. Seshia, et al, IEEE MEMS0. DETF oscillator output oriolis offset Nominal peak Frequency 0 5 Hz oriolis offset sideband output in presence of an applied deg/sec rotation rate at 6 Hz. Output sideband power dbµ Output sideband power dbµ 40 35 30 5 0 5 0 5 0 5 0 5 0 5 Rotation rate signal Offset 540 550 560 570 580 590 600 60 60 630 640 Frequency offset from carrier Hz 35 30 5 0 5 0 5 0 5 sideband output in the absence of rotation 50 540 560 580 600 60 640 Frequency offset from carrier Hz 3 6