JET DRILLING Belt Drive Drill Press.......................... 82 Variable Speed Drill Presses.................... 83 Geared Head Drill Presses..................... 85 Radial Arm Drill Presses....................... 88 Accessories................................. 89
20" FLOOR DRILL PRESS DRILLING 20" FLOOR DRILL PRESS Hinged metal belt and pulley cover coupled with quick adjustment motor mount allow rapid changing of spindle speeds Rotating, 45 tilting, crank-operated worktable with quick release clamp On/off switch located on front of the drill press head A 1/2" diameter external positive depth stop with three nut locking feature for quick adjustment Adjustable tension spindle return spring Spindle is supported by high quality ball bearings Built-in work lamp on all models, bulb not included. Drill chuck and key included JET DRILLING 82 354170 Model Number JDP-20MF Drills to Center of Circle (in.) 20-1/2 Drilling Capacity (in.) 1 Chuck Size (in.) 3/4 Spindle Travel (in.) 4-5/8 Spindle Distance to Base (in.) 46-3/4 Spindle Distance to Table (max/in): 29-1/8 Table Size (in.) 18-5/8 x 16-1/8 T-Slot Size (in.) 5/8 Spindle Taper MT-3 Column Diameter (in.) 3-3/8 Number of Spindle Speeds 12 Range of Spindle Speeds (RPM) 150 4,200 Base Size (in.) 13-5/8 x 22-3/8 Motor 1-1/2HP, 1Ph Floor Space Required (in./l x W x H) 33 x 19 x 67 Net Weight (lbs.) 288 jettools.com
DRILLING 20" VARIABLE SPEED DRILL PRESSES 20" VARIABLE SPEED DRILL PRESSES UL Listed motor Variable spindle speeds Spindle speeds are easily changed by means of a front-mounted dial Conveniently located operating controls Large production table and base Quick-release clamp on table. Easy-to-read internal depth gauge STANDARD EQUIPMENT T-slotted worktable Internal depth stop Tapping and reversing controls on JDP-20VS-3 JET DRILLING 354201 354203 354204 Model Number JDP-20VS-1 JDP-20VS-3/230 JDP-20VS-3/460 Drills to Center of Circle (in.) 20 20 20 Cast Iron Drilling Capacity (in.) 1-1/2 1-1/2 1-1/2 Steel Drilling Capacity (in.) 1-1/4 1-1/4 1-1/4 Cast Iron Tapping Capacity (in.) N/A 3/4 3/4 Column Diameter (in.) 4 4 4 Distance Spindle to Column (max./in.) jettools.com 10 10 10 Spindle Distance to Base 39 39 39 Spindle Distance to Table 28-1/2 28-1/2 28-1/2 Table Size (in.) 22 x 19-1/2 22 x 19-1/2 22 x 19-1/2 Table Travel (in.) 20 20 20 T-Slots (Number & Size) 2 & 5/8 2 & 5/8 2 & 5/8 T-Slot Centers (in.) 8-7/8 8-7/8 8-7/8 Work Table Capacity (lbs.) 110 110 110 Spindle Taper MT-3 MT-3 MT-3 Range of Spindle Speeds 300 2,000 150 2,000 150 2,000 Base Size (in.) 26 x 19 26 x 19 26 x 19 Base Work Table (in.) 13 x 15-1/2 13 x 15-1/2 13 x 15-1/2 Motor Floor Space Required (in./l x W x H) 1-1/2HP, 115/230V, 1Ph, Prewired 230 V 2HP, 230V, 3Ph, 2-speed 2HP, 460V, 3Ph, 2-speed 36 x 22 x 71 36 x 22 x 71 36 x 22 x 71 Net Weight (lbs.) 720 740 740 OPTIONAL EQUIPMENT Drill chucks Drill chuck arbors Vises 52pc. Clamping kit 660058 83
20" ELECTRONIC VARIABLE SPEED DRILL PRESSES DRILLING 20" ELECTRONIC VARIABLE SPEED DRILL PRESSES Runs quieter and smoother than a conventional variable speed head 230V model can run on single phase power Low maintenance head has less moving parts Incorporates a high-low gear box to maintain low speed torque Chrome molybdenum gears are hardened, ground, and shaved Quiet running and longer life Speed can be adjusted in each range during operation LED spindle RPM readout is conveniently mounted Tapping mode allows instantaneous spindle reversal Easy to read internal depth gauge Extra large emergency stop button adds to safe operation Table can be raised from the front or side Large production table and T-slotted dish-in base STANDARD EQUIPMENT Integrated tapping and reversing controls Complete coolant system T-slotted work table JET DRILLING OPTIONAL EQUIPMENT Vises 52 pc. Clamping kit 660058 Drill chucks Drill chuck arbors 84 354210 354212 Model Number JDP-20EVS/230 JDP-20EVS/460 Drills to Center of Circle (in.) 20 20 Cast Iron Drilling Capacity (in.) 1-1/2 1-1/2 Steel Drilling Capacity (in.) 1-3/8 1-3/8 Steel Tapping Capacity (in.) 3/4 3/4 Column Diameter (in.) 4-1/2 4-1/2 Distance Spindle to Column (max./in.) 10-7/16 10-7/16 Spindle Taper MT-3 MT-3 Spindle Travel (in.) 6 6 Number of Spindle Speeds Variable Variable Range of Spindle Speeds (RPM) 65 2000 65 2000 Distance Spindle to Base (max./in.) 44-1/4 44-1/4 Distance Spindle to Table (max./in.) 32-3/8 32-3/8 Table Size (in.) 22 x 18-3/4 22 x18-3/4 Table Weight (max./lbs.) 230 230 T-slot (Number & Size) (in.) 2 & 5/8 2 & 5/8 T-slot Centers 8-1/2 8-1/2 Main Motor 2HP, 230V, 3Ph 2HP, 460V, 3Ph Coolant Motor 1/8HP, 3Ph 1/8HP, 3Ph Floor Space Required (in./l x W x H) 37 x 37 x 82-1/4 37 x 37 x 82-1/4 Net Weight (lbs.) 722 722 jettools.com
DRILLING 20" GEARED HEAD DRILL PRESSES 20" GEARED HEAD DRILL PRESSES Heavy duty design allows a variety of precision drilling applications Easy to read internal depth gauge (GHD-20) Three power down feeds (GHD-20PF) Calibrated fine down feed built-in Built-in spindle lock Head tilts left or right Easy accessible table raiser Large production table and T-slotted base STANDARD EQUIPMENT T-slotted worktable Drill chuck arbor Draw bar JET DRILLING 354020 354024 Model Number GHD-20 GHD-20PF Drills to Center of Circle (in.) 20 20 Cast Iron Drilling Capacity (in.) 1-1/2 1-1/2 Steel Drilling Capacity (in.) 1-1/4 1-1/4 Column Diameter (in.) 4-1/2 4-1/2 Distance Spindle to Column (max./in.) 10 10 Spindle Taper MT-3 MT-3 Spindle Travel (in.) (GHD-20) 5 Spindle Travel (in.) (GHD-20PF) Manual 4-1/2 Spindle Travel (in.) (GHD-20PF) Auto 4-1/4 Quill Diameter (in.) 3 3 Spindle Distance to Base (in.) 44-3/8 44-3/8 Spindle Distance to Table (in.) 30-7/8 30-7/8 Table Size (in.) 21-1/4 x 18-1/2 21-1/4 x 18-1/2 T-slots, Number & Size (in.) 2 & 5/8 2 & 5/8 T-slot Centers (in.) 9 9 Number of Spindle Speeds 12 12 Range of Spindle Speeds (RPM ) Lo Speed Range of Spindle SPeeds (RPM) Hi Speed jettools.com 60, 130, 230, 450, 800, 1500 60, 130, 230, 450, 800, 1500 120, 260, 460, 900, 1600, 3000 120, 260, 460, 900, 1600, 3000 Number of Powerfeeds (GHD-20PF) 3 Range of Powerfeeds.004,.007,.01 Motor 2HP, 230V only, 3Ph, 2 Speed 2HP, 230V only, 3Ph, 2 Speed Floor Space Required (in./l x W x H) 32 x 24 x 71 32 x 24 x 71 Net Weight (lbs.) 660 660 354020 OPTIONAL EQUIPMENT Drill chucks Drill chuck arbors Rotary Phase converter Vises 52 pc. Clamping Kit 660058 85
20" GEARED HEAD DRILLING & TAPPING PRESSES DRILLING 20" GEARED HEAD DRILLING AND TAPPING PRESSES Heavy-duty design allows a variety of precision drilling and tapping applications Easy to read internal depth gauge Three power down feeds (GHD-20PFT) Calibrated fine down feed built-in Built-in spindle lock Head tilts left or right Easy accessible table raiser Large production table and T-slotted base STANDARD EQUIPMENT Integrated tapping and reversing controls T-slotted worktable Drill chuck arbor Draw bar TEFC Motor JET DRILLING 354026 OPTIONAL EQUIPMENT Drill chucks Drill chuck arbors Vises 52pc. Clamping Kit 660058 Rotary Phase converter Note: Use of static equipment will void warranty. 86 354022 354026 Model Number GHD-20T GHD-20PFT Drills to Center of Circle (in.) 20 20 Cast Iron Drilling Capacity (in.) 1-1/2 1-1/2 Cast Iron Tapping Capacity (in.) 13/16 13/16 Steel Drilling Capacity (in.) 1-1/4 1-1/4 Column Diameter (in.) 4-1/2 4-1/2 Distance Spindle to Column (max./in.) 10 10 Spindle Taper MT-3 MT-3 Spindle Travel Manual 5 4-1/2 Auto 4-1/4 Tapping 4-7/8 4-7/8 Quill Diameter (in.) 3 3 Spindle Distance to Base (in.) 44-3/8 44-3/8 Spindle Distance to Table (in.) 30-7/8 30-7/8 Table Size (in.) 21-1/4 x 18-1/2 21-1/4 x 18-1/2 T-slots, number & size 2 & 5/8 2 & 5/8 T-slot Centers 6-1/4 6-1/4 Number of Spindle Speeds 12 12 Range of Spindle Speeds (RPM) Lo Speed Range of Spindle Speeds (RPM) Hi Speed 60, 130, 230, 450, 800, 1500 60, 130, 230, 450, 800, 1500 120, 260, 460, 900, 1600, 3000 120, 260, 460, 900, 1600, 3000 Number of Powerfeeds 3 Range of Powerfeeds.004,.007,.01 Motor 2HP, 230V, 3Ph, 2-speed 2HP, 230V, 3Ph, 2-speed Floor Space Required (in./l x W x H) 32 x 24 x 71 32 x 24 x 71 Net Weight (lbs.) 670 670 jettools.com
DRILLING 20" GEARED HEAD DRILL PRESSES - SERIES E 20" GEARED HEAD DRILL PRESSES SERIES E Heavy-duty design allows a variety of precision drilling applications Helical gears for smooth, quiet operation Easy-to-read depth gauge Eight Spindle speeds T-slotted table with coolant trough Easy accessible table raiser Two position, high/low switch Emergency stop button 354125 JET DRILLING 354121 354121 354125 Model Number GHD20E-4 GHD20E-4PF Drills to Center of Circle (in) 20 20 Steel Drilling Capacity (in.) 1 1 Column Diameter (in.) 3-7/8 3-7/8 Distance Nose to Table (max./in) 30 30 Number of Spindle Speeds 8 8 Range of Spindle Speeds (RPM) jettools.com 130, 260, 420, 535, 840, 1070, 1745, 3490 130, 260, 420, 535, 840, 1070, 1745, 3490 Spindle Taper MT-3 MT-3 Spindle Travel (in.) 5 5 Quill Diameter (in.) 2-3/8 2-3/8 Quill Feed Manual Feed Power Feed Quill Feed Rates ( number & range) 4 (.004,.006,.009,.014) Spindle Distance to Base (in.) 44 44 Spindle Distance to Table (in.) 30 30 Table Size (in.) 15 x 15 15 x 15 Motor (Two Speed) 1.5HP / 1HP, 440V, 3Ph 1.5HP / 1HP, 440V, 3Ph Floor Space Required (in./l x W x H) 24 x 15-3/4 x 70 24 x 15-3/4 x 70 Net Weight (lbs) 450 690 OPTIONAL EQUIPMENT Drill chucks Drill chuck arbors 52 pc Clamping Kit 660058 Vises Rotary Phase converter 87
RADIAL ARM DRILL PRESS DRILLING JET DRILLING 88 RADIAL ARM DRILL PRESS Spindle head has hardened and ground gears mounted on a spline shaft Column designed for rigidity and minimal deflection The arm is ribbed to withstand stress and minimize deflection Arm is mounted with a ground sliding way which elevates easily with the touch of a switch High carbon steel spindle is spline driven and supported by large tapered roller bearings Base plate has T-slots and drain channels Coolant tank is incorporated into the casting Motor has an independent overload protection system Downfeed scale has satin chrome finish Spindle reversing switch is conveniently located Limit switches at lower and upper limits prevent over-travel of arm STANDARD EQUIPMENT Complete coolant system Worktable Amp meter Reversing controls Anchor bolt set Fluorescent worklight Tool box with tools 320032 Model Number JRD-1000 Steel Drilling Capacity (power feed/in.) 1-3/8 Cast Iron Drilling Capacity (in.) 2 Steel Tapping Capacity (in.) 3/4 Cast Iron Tapping Capacity (in.) 1 Steel Boring Capacity (in.) 3 Cast Iron Boring Capacity (in.) 4 Column Diameter (in.) 9 Distance Spindle to Column (min./in.) 16-1/2 Distance Spindle to Column (max./in.) 42-1/4 Head Travel on Arm (in.) 25-1/2 Distance Spindle to Bed (min./in.) 21-5/8 Distance Spindle to Bed (max./in.) 43-3/4 Vertical Movement of Arm (in.) 21-5/8 Size of Worktable (L xw x D/in.) 27 x 16-1/2 x 15 T-Slot (number & size/in.) 3 & 3/4 Spindle Taper MT-4 Spindle Travel (in.) 9 Number of Spindle Speeds 12 Range of Spindle Speeds (RPM) 44 1,500 Number of Feeds 3 Feed per Revolution (in./rev.) 002,.0035,.006 Spindle Motor 2HP, 230V, 3Ph Arm Elevation Motor 1HP Coolant Pump Motor 1/8HP Floor Space Required (in.) 62 x 27 x 80 Net Weight (lbs.) 3520 jettools.com
DRILLING DRILL PRESS VISES AND ACCESSORIES CENTER SLIDE BAR TYPE DRILL PRESS VISES The axial sleeve and movable jaw are cast in one single piece Allowable tolerance between the axial sleeve and center bar is 0.002" The manner in which the center slide bar is connected to the axial sleeve assures an even 360 contact Much more accurate and stable than the traditional screw and cross plate means of attaching the movable jaw to the vise bed 365523 365524 365525 365526 Model Number DPV-3BT DPV-4BT DPV-5BT DPV-6BT Jaw (in./w x D) 3 x 1 4 x 1-1/8 5 x 1-1/4 6 x 1-3/8 Jaw Opening (in.) 2-13/16 3-1/2 4-5/16 5-1/2 Base Width (in.) 5-1/2 6-9/16 7-1/2 9 Base Length (in.) 6-1/47 7 8-1/4 9-13/16 Overall Ht. (in.) 2-3/16 2-3/8 2-5/8 3 DRILL PRESS ANGLE VISES Adjusts quickly to a full 90 vertical or horizontal position High tensile iron casting is strong and heavy Two bolt slots on base provide easy positioning on drill press table 365533 365534 365535 Model Number DPAV-3 DPAV-4 DPAV-5 Jaw (in./w x D) 2-1/2 x 1-1/2 3-1/2 x 1-1/2 4-1/2 x 1-1/2 Jaw Opening (in.) 2-5/8 3-3/16 4 Base Width (in.) 3-5/16 4-1/2 5-1/2 Base Length (in.) 8-1/4 9-5/32 11-1/4 Overall Height (in.) 3-1/8 3-1/2 3-5/8 DRILL PRESS ANGLE VISES WITH SWIVEL BASE JET DRILLING Use with or without swivel base Swivels 360 Quickly adjusts to 90 vertical or horizontal position Constructed of high tensile cast iron 365543 365544 Model Number DPAV-3SB DPAV-4SB Jaw (in./w x D) 2-1/2 x 1-1/2 3-1/2 x 1-1/2 Jaw Opening (in.) 2-5/8 3-3/16 Base Width (in.) 4-1/2 5-5/8 Base Length (in.) 8-1/4 9-3/8 Overall Height (in.) 4-3/8 4-5/8 MORSE TAPER MOUNT DRILL Precision hardened and ground high grade alloy steel All sizes with drift tang MODEL NUMBER SIZE DCA-22 561763 MT-2 x JT-2 DCA-233 561764 MT-2 x JT-33 DCA-26 561765 MT-2 x JT-6 DCA-23 561766 MT-2 x JT-3 DCA-32 561770 MT-3 x JT-2 DCA-333 561771 MT-3 x JT-33 DCA-36 561772 MT-3 x JT-6 DCA-33 561773 MT-3 x JT-3 DCA-34 561774 MT-3 x JT-4 jettools.com 89
DRILL PRESS VISESAND ACCESSORIES DRILLING RAPID ACTION DRILL PRESS VISESES Instant setting by moving sliding steel bar and handle attached to movable jaw Locking the workpiece in the vise jaws is achieved by means of a cam action on the lead bar caused by a single strike of the locking lever 365560 365561 365562 Model Number QGV-3 QGV-4 QGV-6 Jaw (in./w x D) 3-1/4 x 1 4-5/16 x 1 6 x 1-1/4 Jaw Opening (in.) 2-3/4 4-1/4 6 Base Length (in.) 8-5/16 11 14-1/2 Width (in.) 4-1/2 6 9 HORIZONTAL/VERTICAL RAPID ACTION DRILL PRESS VISES Instant setting by moving sliding steel bar and handle attached to movable jaw Locking the workpiece in the vise jaws is achieved by means of a cam action on the lead bar caused by a single strike of the locking lever JET DRILLING 365564 365565 Model Number QGV-3A QGV-4A Jaw (in./w x D) 3-1/8 x 1 4-1/8 x 1 Jaw Opening (in.) 3 4-3/4 Base Length (in.) 9-1/2 12 Base Width (in.) 3-5/16 4-5/16 PRISMATIC PRISMATIC JAWS FOR JET RAPID ACTION DRILL PRESS VISES Instant setting by moving sliding steel bar and handle attached to movable jaw Locking the workpiece in the vise jaws is achieved by means of a cam action on the lead bar caused by a single strike of the locking lever 365566 365567 Model Number PJQ-3 PJQ-4 Fits Jaw Size (in.) 3 4 CLAMPING KITS Metal storage tray can be mounted on machine or wall Three complete sets to choose from 52-piece kit includes: Six T-slot nuts, Six Flange nuts, Four Coupling nuts, Six Step blocks, Six Step clamps, Twenty four Studs, four each (3", 4", 5", 6", 7" & 8" lengths) 660038 660012 660058 Model Number CK-38 CK-12 CK-58 Stud Size 3/8-16 T.P.I. 1/2-13 T.P.I. 5/8-11 T.P.I. T-slot Sizes (in.) 7/16 and 1/2 9/16 and 5/8 11/16 and 3/4 TAPER MOUNT DRILL CHUCKS All components are heat-treated high grade alloy steel Chuck jaws are precision fitted to withstand 115 PSI of torque without distortion All models meet JIS Specification: B4634E Grade 90 STOCK NUMBER TDC-375 TDC-500 TDC-501 TDC-625 TDC-750 Model Number 561702 561704 561706 561708 561709 Capacity (in.) 0-3/8 0-1/2 0-1/2 1/8-5/8 1/8-3/4 Taper Mount JT-2 JT-3 JT-33 JT-3 JT-4 Body Diameter (in.) 1-15/32 1-5/8 1-25/32 2-3/16 2-7/8 Overall Length (in.) 2-3/8 2-31/32 3-1/8 3-11/16 5 jettools.com
Belt Drive Drill Presses.......................... 92 Variable Speed Drill Presses...................... 94 Geared Head Drill Presses........................ 97 Direct Drive Drill Presses........................ 101 Radial Arm Drill Presses........................ 103 Accessories................................... 106
15" AND 20" DRILL PRESSES DRILLING 92 15" AND 20" DRILL PRESSES Cast iron head Large quill allows greater accuracy Head casting features a permanently lubricated ball bearing spindle assembly, using four heavy duty ball bearings mounted in an enclosed quill for extended life Massive T-slotted production work table (Model 2550 only) Table tilts 45 Large ground steel column diameter for maximum head and table support 3-3/8" stroke for deep hole applications Accurate depth stop for precise hole depths STANDARD EQUIPMENT 5/8" Drill chuck and arbor 2530 2500 2550 Type 15" Bench 15" Floor 20"Floor Drills to Center of Circle (in.) 15 15 20 Cast Iron Drilling Capacity (max./in.) 5/8 5/8 3/4 Steel Drilling Capacity (max./in.) 1/2 1/2 5/8 Quill Diameter (in.) 1-7/8 1-7/8 2-1/4 Quill Travel (in.) 3-3/8 3-3/8 4-3/4 Spindle Taper 2 MT 2 MT 3 MT Number & Range of Spindle Speeds (RPM) 12 (250, 340, 390, 510, 600, 650, 990, 1550, 1620, 1900, 2620, 3100) 12 (250, 340, 390, 510, 600, 650, 990, 1550, 1620, 1900, 2620, 3100) 12 (150, 260, 300, 440, 490, 540, 1150, 1550, 1840, 2220, 2950, 4200) Overall Table Size (in.) 10 x 10 10 x 10 18-1/2 x 16-1/2 Table Working Surface (in.) 10 x 10 10 x 10 14 x 16 T-slot Number & Size (in) N/A N/A 3 & 1/2 Column Diameter (in.) 2-7/8 2-7/8 3-5/8 Base Size (in.) 11 x 18-1/2 11 x 19-1/2 22-3/4 x 17-3/4 Spindle to Base (in.) 24-1/2 48-3/4 43-1/2 Motor 3/4HP, 115V, 1Ph, 1725 RPM 3/4HP, 115V, 1Ph, 1725 RPM 1-1/2HP, 115V, 1Ph, 1725 RPM Floor Space Required (in./l x W x H) 26 x 13-3/8 x 39 26 x 13-3/8 x 63-1/2 34 x 21 x 67 Net Weight (lbs.) 157 185 321 *Capacities for continuous production use will vary based on application 2530 2500 2550
DRILLING 15" 6- SPEED DRILL PRESSES 15" 6-SPEED DRILL PRESSES Constructed to provide a solid base for drilling Offers a greater range in spindle speeds than others in this class Larger quill provides greater accuracy Large production work table give the operator the room to work and support for the job 3" Column for head support, while the quill is also supported to lessen deflection STANDARD EQUIPMENT 1/2" Drill Chuck and arbor A3816 A3836 Type 15" Floor 15" Bench Drills to Center of Circle (in.) 15 15 Cast Iron Drilling Capacity (in.) 5/8 5/8 Steel Drilling Capacity (in.) 1/2 1/2 Quill Diameter (in.) 2-1/4 2-1/4 Spindle Travel (in.) 6 6 Number of Spindle Speeds 6 6 Spindle Speeds (RPM) Table Overall/Table Working Surface (in.) 375, 625, 1125, 1950, 3400, 5000 15-1/4 x 17-3/4/ 12-1/2 x 14-1/2 375, 625, 1125, 1950, 3400, 5000 14-1/4 x 12-3/8 / 10-5/8 x 12-3/8 T-slot Number & Size (in.) 2 & 1/2 2 & 1/2 Spindle to Table (in.) 41 Spindle to Base (in.) 47-1/2 11 Overall Height (in.) 67-1/2 36-1/2 Spindle Taper 2 MT 2MT Column Diameter (in.) 3 3 Table Capacity (max./lbs.) 100 100 Motor 1HP, 115/230V, 1Ph Prewired 115V Floor Space Required (in./l x W x H) 30 x 20 x 71 1HP, 115/230V, 1Ph Prewired 115V Net Weight (lbs.) 394 375 A3816 93
15" VARIABLE SPEED DRILL PRESSES DRILLING 15" VARIABLE SPEED DRILL PRESSES Speeds from 400 to 5,000 RPM Handwheel adjustment sets the speeds Large 2-1/4" quill allows greater accuracy 3" column diameter for maximum head support Full bearing support on quill for maximum spindle stiffness 6" stroke for deep hole applications Accurate depth stop for precise hole depths 1/2" Drill chuck and arbor Safety collar 94 A5816 A5836 A5816/A5818 A5836/A5838 Type 15" Floor 15" Bench Drills to Center of Circle (in.) 15 15 Cast Iron Drilling Capacity (max./in.) 5/8 5/8 Steel Drilling Capacity (max./in.) 1/2 1/2 Column Diameter (in.) 3 3 Quill Diameter (in.) 2-1/4 2-1/4 Spindle Taper 2 MT 2 MT Spindle Travel (in.) 6 6 Spindle Speeds (RPM) 400 to 5000 400 to 5000 Overall Table Size (in.) 15-1/4 x 17-3/4 14-1/4 x 21 Table Working Surface (in.) 12-1/2 x 14-1/2 10-5/8 x 12-3/8 T-slot Number & Size (in.) 2 & 1/2 2 & 1/2 Spindle to Table (in.) 41 Spindle to Base (in.) 47-1/2 11 Overall Height (in.) 67-1/2 36-1/2 Motor A5816/A5836 Motor A5818/A5838 1 HP, 115/230V, 1Ph, Prewired 115V 1HP, 230/460V, 3Ph, Prewired 230V Floor Space Required (in./l x W x H) 30 x 20 x 71 1 HP, 115/230V, 1Ph, Prewired 115V 1HP, 230/460V, 3Ph, Prewired 230V Net Weight (lbs.) 426 336 *Capacities for continuous production use will vary based on application wiltontool.com
DRILLING 20" VARIABLE SPEED DRILL PRESSES 20" VARIABLE SPEED DRILL PRESSES Variable spindle speeds from 300 to 2000 RPM External #3 Morse Taper Front mounted positive control depth stop 6" quill travel Massive 3" quill diameter Heavy duty cast iron design Large precision ground T-slot production table for easy set ups Front or side rack and worm gear table raiser Table rotates 360 around the column Machined T-slotted base Head is massively constructed for more accuracy and rigidity 2221VS 2223VS Drills to Center of Circle (in.) 20 20 Cast Iron Drilling Capacity (in.) 1-1/4 1-1/4 Steel Drilling Capacity (in.) 1 1 Column Diameter (in.) 4-1/2 4-1/2 Range of Spindle Speeds (RPM) 300 to 2000 300 to 2000 Distance Spindle to Column (max./in.) 10-7/16 10-7/16 Distance Spindle to Table (in.) 32-3/8 32-3/8 Spindle Travel (in.) 6 6 Spindle Taper 3 MT 3 MT Quill Diameter (in.) 3 3 Table Size (in.) 18-1/8 x 14-3/4 18-1/8 x 14-3/4 T-slot Number & Size (in.) 2 & 5/8 2 & 5/8 Table Travel (in.) 32-3/8 32-3/8 Base Working Surface (in.) 15-1/4 x 12-1/16 15-1/4 x 12-1/16 Base Slots Number & Size (in.) 2 & 5/8 2 & 5/8 Motor for 2221VS 2HP, 115/230V, 1Ph, Prewired 115V 2HP, 230/460V, 3Ph, Prewired 230V Floor Space Required (in./l x W x H) 34-1/4 x 27 x 77-1/4 34-1/4 x 27 x 77-1/4 Net Weight (lbs.) 715 715 * Capacities for continuous production use will vary based on application OPTIONAL EQUIPMENT Coolant system, 1/8HP pump, 115/220V, 1Ph 5512104 Coolant system, 1/8HP pump, 220/440V, 3Ph 5508071 Jacob's chuck, 3/16" 3/4", keyed with #3 arbor 5108010 95
ELECTRONIC VARIABLE SPEED DRILL PRESSES DRILLING ELECTRONIC VARIABLE SPEED DRILL PRESSES Variable spindle speeds from 65 to 2000 RPM #3 Morse taper spindle Latest AC inverter variable speed technology High torque at all speeds both forward and reverse Continuous speed adjustment while in operation Front mounted LED spindle RPM readout Forward and reverse for tapping Emergency stop Front mounted positive control depth stop Large precision ground T-slot production table for easy set ups Head is massively constructed for more accuracy and rigidity 96 OPTIONAL EQUIPMENT Coolant system, 1/8HP pump, 220V/440V, 3Ph Coolant system, 1/8HP pump, 115V/220V, 1Ph Jacob's chuck, 3/16" 3/4", keyed with #3 arbor 5508071 5512104 5108010 2232AC 2234AC Drills to Center of Circle (in.) 20 20 Cast Iron Drilling Capacity (in.) 1-1/2 1-1/2 Steel Drilling Capacity (in.) 1-3/8 1-3/8 Quill Diameter (in.) 3 3 Distance Spindle to Column (in.) 10-7/16 10-7/16 Distance Spindle to Table (max./in.) 32-3/8 32-3/8 Spindle Speeds (RPM) 65 to 2000 65 to 2000 Spindle Travel (in.) 6 6 Spindle Taper 3 MT 3 MT Quill Travel (in.) 6 6 Column Diameter (in.) 4-1/2 4-1/2 Table Working Surface (in.) 18-1/8 x 14-3/4 18-1/8 x 14-3/4 T-slot Number & Size (in.) 2 & 5/8 2 & 5/8 Table Travel (in.) 32-3/8 32-3/8 Table Overall Size (in.) 22 x 18-3/4 22 x 18-3/4 Base Working Surface (in.) 15-1/4 x 12-1/16 15-1/4 x 12-1/16 Base Slots Number & Size (in.) 2 & 5/8 2 & 5/8 Overall Base Size (in.) 27-2/4 x 20 27-2/4 x 20 Motor 2HP, 230V, 3Ph 2HP, 460V, 3Ph Floor Space Required (in./l x W x H) 37 x 27 x 82-1/4 37 x 27 x 82-1/4 Net Weight (lbs.) 792 792 wiltontool.com
DRILLING 20" WILTON/ARBOGA GEAR HEAD DRILL PRESSES 20" WILTON/ARBOGA GEAR HEAD DRILL PRESSES Helical gears for smooth, quiet operation Quick release drill ejector Safety latch to prevent head dropping when unclamped Eight spindle speeds T-Slotted table with coolant trough Head and table rotate 360 around column 2 position, High/Low switch 3-15/16" Column diameter English/Metric depth gauge A2608-1/ A2608-2/ A2608-4 A2608M-PF2/ A2608M-PF4 Drills to Center of Circle (in.) 20 20 Drilling Capacity Mild Steel (in.) 1-1/4 1-1/4 Tapping Capacity Mild Steel (in.) 1/2 1/2 Column Diameter (in.) 3-15/16 3-15/16 Distance Spindle to Table (max./in.) 35-5/8 35-5/8 Spindle Taper 3 MT 3MT Spindle Speeds (RPM) 8 (130, 260, 420, 840, 535, 1070, 1745, 3480) 8 (130, 260, 420, 840, 535, 1070, 1745, 3480) Quill Feed Manual Power Feed Quill Feed Rates (IPR) N/A (.004,.006,.009,.012) Quill Travel (in.) 5-1/8 5-1/8 Quill Diameter (in.) 2-3/8 2-3/8 Vertical Movement of Drill Head 8-5/8 8-5/8 Table Size (in.) 15-3/4 x 19-3/4 15-3/4 x 19-3/4 T-slot Number & Size (in) 2 & 9/16 2 & 9/16 Table Weight Capacity (lbs.) 350 350 Vertical Movement of Table (in.) 24-1/2 24-1/2 Motor for A2608-1 (2 speed) 3/4 to 1HP, 115V, 1Ph Motor for A2608-2 (2 speed) 1 to 1-1/2HP, 220V, 3Ph 1 to 1-1/2HP, 220V, 3Ph Motor for A2608-4 (2 speed) 1 to 1-1/2HP, 440/460V, 3Ph 1 to 1-1/2HP, 440/460V, 3Ph Floor Space Required (in./l x W x H) 24 x 22 x 72 24 x 22 x 72 Net Weight (lbs.) 475 600 A2608M-PF2 OPTIONAL EQUIPMENT Keyless drill chuck and arbor KDC130-MT3 Jacobs drill chuck, key and arbor 5108010 Foot operated start/stop switch 5245631A Flanged Quill 2G08459 5-speed forward/reverse switch* 1820061 Foot reversing switch* 5245631 * 3 phase machines only 97
25" WILTON/ARBOGA GEAR HEAD DRILL PRESSES DRILLING 25" WILTON/ARBOGA GEAR HEAD DRILL PRESSES Helical gears for smooth, quiet operation Quick release drill ejector English/Metric depth gauge T-Slotted table and base with coolant trough Automatic feed control buttons located on feed levers Electro-magnetic clutch power feed Head and table rotate 360 around column No-volt release prevents spindle start when power returns after shut down OPTIONAL EQUIPMENT Automatic spindle reverse 1T05030 Foot reversing switch 5245631 Foot operated start/stop switch 5245631A 98 A3808M-PF2 A3808M-PF4 Drills to Center of Circle (in.) 25 25 Drilling Capacity Mild Steel (in.) 1-3/8 1-3/8 Tapping Capacity Mild Steel (in.) 3/4 3/4 Column Diameter (in.) 4-15/16 4-15/16 Range of Spindle Speeds (RPM) 8(90, 190, 320, 640, 530, 1060, 1790, 3610) 8(90, 190, 320, 640, 530, 1060, 1790, 3610) Spindle Taper 4MT 4MT Quill Feed Power Feed Power Feed Distance Spindle to Table (max./in.) 32 32 Quill Feed Rates (IPR) 4 (.004,.006,.009,.012) 4 (.004,.006,.009,.012) Quill Travel (in.) 5-1/8 5-1/8 Quill Diameter (in.) 2-3/8 2-3/8 Vertical Movement of Drill Head (in.) 9 9 Table Size (in.) 15-3/4 x 19-1/2 15-3/4 x 19-1/2 T-slot Number & Size (in) 2 & 9/16 2 & 9/16 Table Weight Capacity (lbs.) 350 350 Vertical Movement of Table (in.) 24-1/2 24-1/2 Motor 2-1/4 to 3HP, 220V, 3Ph, 2-Speed 2-1/4 to 3HP, 460V, 3Ph Floor Space Required (in./l x W x H) 26 x 23 x 71 26 x 23 x 71 Net Weight (lbs.) 640 640 wiltontool.com
DRILLING 26" WILTON/ARBOGA GEAR HEAD DRILL PRESSES 26" WILTON/ARBOGA GEAR HEAD DRILL PRESSES Helical gears for smooth, quiet operation Quick release drill ejector English/Metric depth gauge Machined, T-Slotted base plate Head and table rotate 360 around column No-volt release prevents spindle start when power returns after shut down Fully enclosed spindle MODEL NUMBER A3008-2/ A3008-4 A3008M-PF2/ A3008M-PF4 Drills to Center of Circle (in.) 26 26 Drilling Capacity Mild Steel (in.) 1-1/4 1-1/4 Tapping Capacity Mild Steel (in.) 5/8 5/8 Distance Spindle to Table (max./in.) 35 35 Spindle Taper 3MT 3MT Range of Spindle Speeds (RPM) 8(90, 190, 320, 530,640, 1060, 1790, 3610) 8 (90, 190, 320, 530,640, 1060, 1790, 3610) Column Diameter (in.) 4-1/2 4-1/2 Quill Feed Manual Power Feed Quill Feed Rates (IPR) 4 (.004,.006,.009,.012) Quill Travel (in.) 6 6 Quill Diameter (in.) 2-7/16 2-7/16 Vertical Movement of Drill Head (in.) 9 9 Table Size (in.) 15-3/4 x 19-3/4 15-3/4 x 19-3/4 T-slot Number & Size (in) 2 & 9/16 2 & 9/16 Table Weight Capacity (lbs.) 450 450 Vertical Movement of Table 30 30 Motor for A3008-2/ A3008M-FP2 (2 speed) 1-1/2 to 2HP, 220V, 3Ph 1-1/2 to 2HP, 220V, 3Ph Motor for A3008-4/ A3008M-FP4 (2 speed) 1-1/2 to 2HP, 440/460V, 3Ph 1-1/2 to 2HP, 440/460V, 3Ph Floor Space Required (in./l x W x H) 28 x 24 x 72 28 x 24 x 72 Net Weight (lbs.) 565 600 A3008M-PF2 OPTIONAL EQUIPMENT Flanged Quill 1T08019 Automatick spindle reverse 1T05030 Foot reversing switch 5245631 Foot operated start/stop switch 5245631A 99
26" WILTON/ARBOGA GEAR HEAD DRILL PRESSES DRILLING 26" WILTON/ARBOGA GEAR HEAD DRILL PRESSES Helical gears for smooth, quiet operation Quick release drill ejector English/Metric depth gauge Machined, T-Slotted base plate Head and table rotate 360 around column No-volt release prevents spindle start when power returns after shut down Fully enclosed spindle Large T-Slotted Table A4008-2 OPTIONAL EQUIPMENT Foot operated start/stop switch 5245631A Automatic spindle reverse 1T05030 Foot reversing switch 5245631 Flanged Quill 2GO8599 100 A4008-2 / A4008-4 A4008M-PF2/ A4008M-PF4 Drills to Center of Circle (in.) 26 26 Drilling Capacity Mild Steel (in.) 1-7/8 1-7/8 Tapping Capacity Mild Steel (in.) 1 1 Column Diameter (in.) 5-1/2 5-1/2 Range of Spindle Speeds (RPM) 8 (108, 162, 240, 360, 528, 805, 1175, 1800) 8 (105, 162, 240, 360, 528, 805, 1175, 1800) Spindle Taper 4 MT 4 MT Quill Feed Manual Power Feed Quill Feed Rates (IPR) 4 (.004,.006,.009,.013 ) Quill Travel (in.) 8 8 Quill Diameter (in.) 2-3/4 2-3/4 Distance Spindle to Table (max./in.) 32 32 Table Size (in.) 20 x 24 20 x 24 Table Weight Capacity (lbs.) 550 550 Vertical Movement of Table (in.) 25 25 Motor for A4008-2/ A4008M-PF2 Motor for A4008-4/ A4008M-PF4 Floor Space Required (in./l x W x H) 3HP, 220V, 3Ph 3HP, 440/460V, 3Ph 3HP, 220V, 3Ph 3HP, 440/460V, 3Ph 23 x 28 x 81 23 x 28 x 81 Net Weight (lbs.) 700 750 wiltontool.com
DRILLING DIRECT DRIVE ROUND COLUMN DRILL PRESSES DIRECT DRIVE ROUND COLUMN DRILL PRESSES WITH MECHANICAL CLUTCH Two speed forward and reverse switch Mechanical Powerfeed clutch engagement Heavy duty quill and spindle Tempered, ground spindle with internal taper mounted in precision bearings for maximum accuracy, minimizing deflection Speed and feed selectors are located on one side of the drill head for convenience and ease of operation Oversized base is precision ground with T-slots for added versatility and stability Spindle gear box is equipped with steel hardened, ground, shafts and gears Spindle gear box is internally lubricated in a continuous oil bath for long term smooth operation Tilting table, 45 left and right Powerfeed can be disengaged manually STANDARD EQUIPMENT Automatic tool ejector Manual quill lock Coolant system Low voltage at switch 2360 2350 2360 2380 Drills to Center of Circle (in.) 28 30 33 Cast Iron Drilling Capacity (in.) 1-7/8 2-5/32 2-7/8 Steel Drilling Capacity (in.) 1-3/4 2 2-3/4 Cast Iron Tapping Capacity (in.) 1-3/4 2 2-3/8 Steel Tapping Capacity (in.) 1-9/16 1-3/4 2-1/8 Quill Diameter (in.) 3.228 3.465 3.78 Distance Spindle to Column (max./in.) 14 15 16-1/2 Number & Range of Spindle Speeds (RPM) 9 (82, 120, 180, 240, 354, 528, 678, 1026, 1524) 9 (55, 98, 156, 198, 346, 456, 576, 822, 1338) 12 (42, 58, 86, 116, 154, 249, 304, 412, 554, 748, 1098, 1458) Automatic Feeds (in.).004,.008,.012,.016.003,.006,.010,.014.002,.004,.006,.008,.014,.020 Spindle Travel (in.) 9 10 11 Spindle Distance to Base (in.) 49 50 51 Spindle Distance to Table (min./in.) 2.67 2-3/4 2-3/4 Spindle Distance to Table (max./in.) 30-1/2 30-1/2 30-1/2 Table Size (in.) 22 x 19 22 x 19 23-1/2 x 23-1/2 T-Slot Size (in.) 1/2 5/8 5/8 Work Table Capacity (lbs) 400 400 400 Spindle Taper 4MT 4MT 5MT Base Slots Size (in.) 5/8 5/8 5/8 Motor 3HP, 230/460V, 3Ph Prewired 230V 4HP, 230/460V, 3Ph Prewired 230V 7-1/2HP, 230/460V, 3Ph Prewired 230V Floor Space Required (in./ L x W x H) 40 x 30 x 95 53 x 30 x 108 55 x 33 x 110 Net Weight (lbs) 1840 2405 3065 101
DIRECT DRIVE ROUND COLUMN DRILL PRESSES DRILLING DIRECT DRIVE ROUND COLUMN WITH ELECTRO-MAGNETIC CLUTCH DRILL PRESSES Push button control panel Power feed gear box fitted with an electro-magnetic clutch for power feed engagement and overload protection Heavy duty quill and spindle with manual quill locking Tempered, ground spindle with internal taper mounted in precision bearings for maximum accuracy, minimizing deflection Speed and feed selectors are located on one side of the drill head for convenience and ease of operation Oversized base is precision ground with T-slots for added versatility and stability Coolant tank and pump integrated into base Spindle gear box is equipped with steel hardened, ground, shafts and gears Spindle gear box is internally lubricated in a continuous oil bath for long term smooth operation STANDARD EQUIPMENT Automatic tool ejector Manual quill lock Coolant system Low voltage at switch 2455 102 2401/2402* 2404* 2444/2445* 2455/2456* 2475/2476* Drills to Center of Circle (in.) 28 28 30 33 33 Steel Drilling Capacity (in.) 1-3/8 1-3/4 2 2-3/8 2-3/4 Steel Tapping Capacity (in.) 1-1/2 1-9/16 1-3/4 2 2-1/8 Quill Diameter (in.) 3.228 3.228 3.465 3.465 3.78 Distance Spindle to Column (max./in.) 14 14 15 16-1/2 16-1/2 Number & Range of Spindle Speeds (RPM) 8(112, 160, 245, 358, 532, 762, 1164) 9 (82, 120, 180, 354, 528, 678, 1026, 1524) 9 (55, 98, 156, 198, 346, 456, 576, 822, 1338) Automatic Feeds (in.) 3 (.004,.007,.010) 4 (.004,.008,.012,.016) 4 (.003,.006,.010,.014) 12 (48, 72, 96, 144, 186, 234, 288, 360, 480, 804, 996, 1278) 6 (.002,.004,.006,.008,.014,.020) 12 (42, 58, 86, 116, 154, 249, 304, 412, 554, 748, 1098, 1485) 6 (.002,.004,.006,.008,.014,.020) Spindle Travel (in.) 7 9 10 10 11 Spindle Distance to Base (in.) 48 49 50 51 51 Spindle Distance to Table (min./in.) 1.37 2.67 2.75 2.95 2.75 Spindle Distance to Table (max./in.) 30-1/2 30-1/2 30-1/2 30-1/2 30-1/2 Table Size (in.) 22 x 19 22 x 19 33-1/2 x 23-1/2 33-1/2 x 23-1/2 33-1/2 x 23-1/2 T-slot Number & Size (in.) 3 & 1/2 3 & 1/2 3 & 5/8 3 & 5/8 3 & 5/8 Work Table Capacity (lbs.) 575 575 575 750 750 Spindle Taper 4MT 4MT 4MT 5MT 5MT Motor 2HP, 230/460V, 3Ph Prewired 230V 3HP, 230/460V, 3Ph Prewired 230V 4HP, 230/460V, 3Ph Prewired 230V 5-1/2HP, 230/460V, 3Ph Prewired 230V 7-1/2HP, 230/460V, 3Ph Prewired 230V Floor Space Required (in./ L x W x H) 50 x 27 x 98 50 x 27 x 98 53 x 30 x 108 53 x 33 x 109 55 x 33 x 115 Net Weight (lbs.) 1632 1632 2405 2800 2536 * Equipped with Automatic Tapping Control wiltontool.com
DRILLING 3' ARM RADIAL DRILL PRESS wiltontool.com 720R Steel Drilling Capacity (in.) 1-1/2 Cast Iron Drilling Capacity (in.) 2 Steel Tapping Capacity (in.) 3/4 Cast Iron Tapping Capacity (in.) 1 Steel Boring Capacity (in.) 2-3/4 Cast Iron Boring Capacity (in.) 4 Column Diameter (in.) 8-1/4 Distance from Column to Spindle (max./in.) 29-1/2 Distance from column to spindle center, Min. (in.) 8-5/8 Travel of head (Horizontal) (in.) 20-7/8 Distance from base to spindle end, Max. (in.) 41-3/4 Distance from base to spindle end, Min. (in.) 9-5/8 Travel of arm (Vertical) (in.) 23-13/16 Table Size (in.) 23-5/8 x 17-1/2 x 15 T-slot Number & Size (in) 3 & 3/4 Base Dimensions (in.) 49-5/8 x 25-3/16 x 6-9/32 Spindle Taper 4 MT Spindle Stroke (in.) 8-1/4 Range of Spindle Speeds (RPM) 6 (88 1500) Feed Rates (IPR).002,.004,.006 Motor Elevating Motor Coolant Pump Motor 3HP, 230/460V, 3Ph, Prewired 230V 1HP 1/8HP Machine Height from Floor (max./in.) 85-7/16 Floor Space Required (in./l x W x H) 64 x 32 x 85 Shipping Weight (lbs.) 2970 3' ARM RADIAL DRILL PRESSES The power train gears and spline shafts are made of the finest quality, heat treated and ground nickel chrome steel giving extra strength and smoothness to high torque loads The spindle is made of the finest case hardened steel, for extra strength and wear The spindle is supported by double row taper roller and thrust ball bearings at the nose, with thrust and radial axis bearings at the top Built to withstand exceptionally heavy drilling and boring loads and to insure maximum accuracy Arm raising safety device prevents arm from dropping Counter balanced mechanism for spindle return 6 speeds/3 feed rates make exotic materials easier to drill, bore and tap Centralized control center Automatic tool ejector Independent arm electric clamping system, which locks and unlocks the head and column Push button controls are all reduced to 110V Electrical circuits are located in the built-in control box at the rear of the arm--this keeps the controls dust-and-humidity-free while making them easily accessible for maintenance Entire frame is made of Meehanite and high tensile strength cast iron to handle the heaviest of jobs STANDARD EQUIPMENT Built-in work light Coolant pump Tool kit Box table 103
4' ARM RADIAL DRILL PRESSES DRILLING 104 1230R 4' ARM RADIAL DRILL PRESSES Power train gears and spline shafts are made of the finest quality, heat treated and ground nickel chrome steel giving extra strength and smoothness to high torque loads The spindle is made of the finest case hardened steel, for extra strength and wear The spindle is supported by double row taper roller and thrust ball bearings at the nose, with thrust and radial axis bearings at the top The spindle is built to withstand exceptionally heavy drilling and boring loads and to insure maximum accuracy Push button controls are all reduced to 110V Electrical circuits are located in the built-in control box at the rear of the arm this keeps the controls dust and humidity free while making them easily accessible for maintenance Entire frame is made of Meehanite and high tensile strength cast iron to handle the heaviest of jobs Arm raising safety device prevents arm from dropping Counter balanced mechanism for spindle return 12 speeds/3 feed rates make exotic materials easier to drill, bore and tap Centralized control center Automatic tool ejector Independent manual arm clamping system, which locks and unlocks the head and column STANDARD EQUIPMENT Built-in work light Coolant pump Tool kit Box table 1100R 1100R-4 1230R 1230R-4 Steel Drilling Capacity (in.) 1-3/4 1-3/4 1-7/8 1-7/8 Cast Iron Drilling Capacity (in.) 2-1/4 2-1/4 2-5/16 2-5/16 Steel Tapping Capacity (in.) 1 1 1 1 Cast Iron Tapping Capacity (in.) 1-1/4 1-1/4 1-1/2 1-1/2 Steel Boring Capacity (in.) 3-3/8 3-3/8 3-3/8 3-3/8 Cast Iron Boring Capacity (in.) 4-3/4 4-3/4 4-3/4 4-3/4 Column Diameter (in.) 10-1/4 10-1/4 11-13/16 11-13/16 Distance from Column to Spindle (max./in.) 43-5/16 43-5/16 46 46 Distance from Column to Spindle (min./in.) 9-5/8 9-5/8 13-3/4 13-3/4 Travel of head (Horizontal) (in.) 33-5/8 33-3/8 35 35 Distance Base to Spindle (max./in.) 50-3/8 50-3/8 54 54 Distance Base to Spindle (min./in.) 12-5/8 12-5/8 19-3/8 19-3/8 Travel of arm (Vertical/in.) 24 24 34-5/8 34-5/8 Table Dimensions (in.) 24-3/4 x 20-1/2 x 16-1/2 24-3/4 x 20-1/2 x 16-1/2 27-7/8 x 20-1/2 x 16-1/2 27-7/8 x 20-1/2 x 16-1/2 T-slot Number & Size (in.) 3 & 3/4 3 & 3/4 3 & 3/4 3 & 3/4 Base Dimensions (in.) 67-3/4 x 28 x 6-1/2 67-3/4 x 28 x 6-1/2 67-3/4 x 28 x 6-1/2 67-3/4 x 28 x 6-1/2 Spindle Taper 4 MT 4MT 4 MT 4 MT Quill Travel (in.) 9 9 9-7/8 9-7/8 Spindle Travel w/power Feed Engaged (in.) 4 4 4 4 Spindle Speeds (RPM) 12 (44 1500) 12 (44 1500) 12 (45 1550) 12 (45 1550) Feed Rates (IPR) 3 (.002,.004,.006) 3 (.002,.004,.006) 3 (.002,.004,.006) 3 (.002,.004,.006) Motor (2-Speed) (Low & High) 1-1/2 to 3HP, 230V, 3Ph 1-1/2 to 3HP, 460V, 3Ph 2-1/2 to 5HP, 230V, 3Ph 2-1/2 to 5HP, 460V, 3Ph Elevating Motor 1HP 1HP 1HP 1HP Coolant Pump Motor 1/8HP 1/8HP 1/8HP 1/8HP Machine Height from Floor (in.) 100 100 109-1/2 109-1/2 Floor Space Required(in./L x W x H) 74 x 34 x 89 74 x 34 x 39 80 x 39 x 89 80 x 39 x 89 Shipping Weight (lbs.) 4290 4290 4620 4620
DRILLING 5' ARM RADIAL DRILL PRESS wiltontool.com 1600R Drilling Capacity (in.) 2-1/2 Cast Iron Drilling Capacity (in.) 2-7/8 Steel Tapping Capacity (in.) 2 Cast Iron Tapping Capacity (in.) 2-3/8 Steel Boring Capacity (in.) 5 Cast Iron Boring Capacity (in.) 7-3/8 Column Diameter (in.) 17 Distance from Column to Spindle (max./in.) 63 Distance from Column to Spindle (min./in.) 17 Travel of head (Horizontal) (in.) 49-5/8 Distance Base to Spindle (max./in.) 63 Distance Base to Spindle (min./in.) 13 Travel of arm (Vertical/in.) 50 Table Dimensions (in.) 27-7/8 x 19-5/8 x 15-3/4 T-slot Number & Size (in.) 3 & 7/8 Base Dimensions (in.) 97-5/8 x 41-11/32 x 8-1/4 Spindle Taper 5 MT Quill Travel (in.) 14-9/16 Spindle Travel w/power Feed Engaged (in.) 13 Range of Spindle Speeds (RPM) 12 (40 1920) Feed Rates (IPR) Motor Elevating Motor Clamping Motor Coolant Pump Motor 6 (.003.038 IPR) 7-1/2HP, 230/460V, 3Ph, Prewired 230V 2HP 1HP 1/2HP Machine Height from Floor (in.) 124-58/64 Floor Space Required(in./L x W x H) 116 x 55 x 112 Shipping Weight (lbs.) 11,220 5' ARM RADIAL DRILL PRESSES The power train gears and spline shafts are made of the finest quality, heat treated and ground nickel chrome steel giving extra strength and smoothness to high torque loads The spindle is made of the finest case hardened steel, for extra strength and wear The spindle is supported by double row taper roller and thrust ball bearings at the nose, with thrust and radial axis bearings at the top The spindle is built to withstand exceptionally heavy drilling and boring loads and to insure maximum accuracy Push button controls are all reduced to 110V Electrical circuits are located in the built-in control box at the rear of the arm this keeps the controls dust-and-humidity-free while making them easily accessible for maintenance Entire frame is made of Meehanite and high tensile strength cast iron to handle the heaviest of jobs Arm raising safety device prevents arm from dropping Counter balanced mechanism for spindle return 12 speeds/6 feed rates make exotic materials easier to drill, bore and tap Centralized control center Automatic tool ejector Hydraulic head and column clamping STANDARD EQUIPMENT Built-in work light Coolant pump Tool kit Box table 105
DRILL PRESS VISES DRILLING CAM ACTION DRILL PRESS VISES Simple push or pull on the center bar knob sets the jaw in position Easy press locking lever cams the jaw ahead 3/32", exerting a holding pressure that is adjustable from 400 to 1100 lbs. Base is designed for clear through drilling applications Unique top locking lever can be raised or lowered to tighten or loosen against the workpiece STOCK NUMBER MODEL NUMBER JAW WIDTH (IN.) JAW OPENING (IN.) SUPER PRECISION DRILL PRESS VISES JAW DEPTH (IN.) SHIP WEIGHT (LBS.) 13400 1203 3 3 1-1/4 10 13401 1204 4 4-11/16 1-5/16 18 13402 1206 6 6-3/16 1-13/16 34 13403 1208 8 8-3/16 2 51 Rugged design makes these vises perfect for even the most difficult of drilling, tapping and reaming operations Body made from close grain aged cast iron Ground vise bed for smooth and cons i stent jaw movement Jaws are hardened and grounded, with cross patterned 90 V-grooves in the stationary jaw facilitating holding of round pieces both horizontally and vertically Hardness of jaws-55+3hrc STOCK NUMBER MODEL NUMBER JAW WIDTH (IN.) VERSATILE DRILL PRESS VISES Made from high grade cast iron Ground vise bed for smooth, consistent jaw movement Hardened top V-groove jaws JAW OPENING (IN.) Rugged design and large workload capacity JAW DEPTH (IN.) SHIP WEIGHT (LBS.) 11718 DPV/80 3-3/16 3-1/2 1 13 11719 DPV/100 4 4 1-1/4 20 STOCK NUMBER Continuous Nut MODEL NUMBER JAW WIDTH (IN.) JAW OPENING (IN.) JAW DEPTH (IN.) SHIP WEIGHT (LBS.) 63238 1335 3 2-3/4 1-7/8 6 63239 1345 4 4 2-1/8 12 63240 1360 5 5 2-1/8 24 Rapid Acting Nut 63241 1435 3-1/2 4-1/4 1-3/4 11 63242 1445 4-1/2 4-3/4 1-7/8 15 63243 1460 6 6-3/4 2-1/8 28 STANDARD & ANGLE DRILL PRESS VISES Precision grinding of sides and front side face permits additional mounting positions for drilling, tapping or reaming Combining a smooth moveable jaw plate with a cross-patterned 90 V-groove stationary jaw The vise is recommended for general use STOCK NUMBER MODEL NUMBER JAW WIDTH (IN.) JAW OPENING (IN.) JAW DEPTH (IN.) SHIP WEIGHT (LBS.) 106 Standard Models 12800 25 2-1/2 2-9/16 1-1/2 6 12860 30 3 3-1/8 1-3/4 10 Angle Models 12850 25A 2-1/2 2-1/2 1-1/2 12 12870 30A 3-1/8 3-1/8 1-3/4 17 wiltontool.com
DRILLING DRILLING ACCESSORIES KEYLESS DRILL CHUCKS WITH INTEGRAL SHANK Integral shank design eliminates the possiblilty of the chuck slipping on its arbor It is ideal for all your drill press and machining center operations All parts are precision ground, heat treated and balanced with each one being precision tested to.0019" T.I.R. CAPACITY (IN.) MALE TAPER WEIGHT (LBS.) KDC80-MT2 0 5/16 MT-2 1-1/2 KDC130-MT3 0 1/2 MT-3 2-1/2 KDC130-MT4 0 1/2 MT-4 2-3/4 KDC160-MT3 1/8 5/8 MT-3 3-1/2 KDC160-MT4 1/8 5/8 MT-4 4 PRECISION KEYLESS DRILL CHUCKS-TAPPER MOUNTED These chucks incorporate a unique self-tightening feature, whick allows them to grip the cutting tool tighter as more torque is applied Even when high torque is applied, the chucks can be easily opened by hand Extremely high accurachy and precision design make these chucks suitable for use on machining centers, CNC machines and conventional equuipment All parts are precision ground, heat treated and balanced with each chuck being precision tested to.0019" T.I.R. CAPACITY (IN.) TAPER MOUNT WEIGHT (LBS.) KDC100-JT2 0 3/8 JT2 1-1/2 KDC100-JT33 0 3/8 JT33 1-1/2 KDC130-JT33 0 1/2 JT33 2 KDC130-JT6 0 1/2 JT6 2 KDC160-JT6 1/8 5/8 JT6 2-1/2 KDC160-JT3 1/8 5/8 JT3 2-1/2 ARBORS Precision CNC machined and ground arbors provide high accuracy and close tolerance fits For best accuracy and fit we recommend mounting Wilton keyless drill chucks on Wilton arbors CHUCK TAPER SHANK TAPER WEIGHT (OZ.) DCA2-JT2 JT2 MT-2 5 DCA2-JT33 JT33 MT-2 5 DCA2-JT6 JT6 MT-2 5 DCA2-JT3 JT3 MT-2 7 DCA3-JT33 JT33 MT-3 11 DCA3-JT6 JT6 MT-3 11 DCA3-JT3 JT3 MT-3 12 DCA4-JT6 JT6 MT-4 21 DCA4-JT3 JT3 MT-4 23 107
DRILLING ACCESSORIES DRILLING REVERSIBLE TAPPING HEADS Pre-selective torque drive prevents tap breakage 1.75: 1 reverse ratio increases productivity Self-feed ensures gauge perfect threads Re-entry cushion eliminates cross threading Right hand tapping only STANDARD EQUIPMENT Tap holder Two morse taper arbors Two keys Brake rod Hex wrench Packaged in wooden box with latch TAPPING CAPACITY HEAD WEIGHT PACKAGE WEIGHT WTH25 5/64 1/4 2-1/2 5 WTH50 3/16 7/16 5-1/4 9-3/4 WTH75 5/16 3/4 10 16-1/4 MILLING TABLES Highest quality meehanite castings Table and ways precision ground Adjustable keys and locks for added rigidity Leadscrews supported by axial ball bearings Table accuracy on horizontal plane within 0.001" Leadscrew accuracy 0.0005" 3 T-Slots 5104561 5107901 Working Surface (in.) 22-9/16 x 9-7/16 17-23/32 x 9-7/16 Longitudinal Feed (in.) 14-49/64 14-49/64 Crossfeed (in.) 6-1/8 6-1/8 Length of Bedplate (in.) 10-13/64 10-13/64 Width of Bedplate (in.) 9-7/32 9-7/32 Total Height (in.) 4-1/2 4-1/2 Net Weight (lbs.) 123 165 ADAPTER PLATE WITH STUD For use with all WILTON/ARBOGA Gear Head Drill Presses. Fits directly onto the standard table knee. Will not fit ARBOGA Model A4008. DESCRIPTION 5107980 Adapter plate with stud ADAPTER PLATE WITH STUD Can be used on all WILTONdrill presses with 18" x 25" tables. These adapter plates bolt directly onto Wilton's standard T-slot production table. 108 DESCRIPTION 5046110 Box Plate Adapter wiltontool.com