Applications Zero Voltage Switching SMPS Telecom and Server Power Supplies Uninterruptible Power Supplies Motor Control applications SMPS MOSFET PD - 9445A HEXFET Power MOSFET V DSS R DS(on) typ. Trr typ. I D 600V 385mΩ 30ns 5A Features and Benefits SuperFast body diode eliminates the need for external diodes in ZVS applications. Lower Gate charge results in simpler drive requirements. Enhanced dv/dt capabilities offer improved ruggedness. Higher Gate voltage threshold offers improved noise immunity. TO-247AC Absolute Maximum Ratings Parameter Max. Units I D @ T C = 25 C Continuous Drain Current, V GS @ V 5 I D @ T C = 0 C Continuous Drain Current, V GS @ V 9.7 A I DM Pulsed Drain Current c 60 P D @T C = 25 C Power Dissipation 280 W Linear Derating Factor 2.3 W/ C V GS Gate-to-Source Voltage ±30 V dv/dt Peak Diode Recovery dv/dt e V/ns T J Operating Junction and -55 to 50 T STG Storage Temperature Range C Soldering Temperature, for seconds 300 (.6mm from case ) Mounting torque, 6-32 or M3 screw.() N m (lbf in) Diode Characteristics Symbol Parameter Min. Typ. Max. Units Conditions I S Continuous Source Current 5 MOSFET symbol (Body Diode) A showing the I SM Pulsed Source Current 60 integral reverse (Body Diode)Ãc p-n junction diode. V SD Diode Forward Voltage.5 V T J = 25 C, I S = 5A, V GS = 0V f t rr Reverse Recovery Time 30 200 ns T J = 25 C, I F = 5A 240 360 T J = 25 C, di/dt = 0A/µs f Q rr Reverse Recovery Charge 450 670 nc T J = 25 C, I S = 5A, V GS = 0V f 80 620 T J = 25 C, di/dt = 0A/µs f I RRM Reverse Recovery Current 5.8 8.7 A T J = 25 C t on Forward Turn-On Time Intrinsic turn-on time is negligible (turn-on is dominated by LSLD) www.irf.com G D S 08/26/04
Static @ T J = 25 C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Units V (BR)DSS Drain-to-Source Breakdown Voltage 600 V V (BR)DSS / T J Breakdown Voltage Temp. Coefficient 0.39 V/ C R DS(on) Static Drain-to-Source On-Resistance 385 460 mω V GS(th) Gate Threshold Voltage 3.0 5.0 V I DSS Drain-to-Source Leakage Current 50 µa 2.0 ma I GSS Gate-to-Source Forward Leakage 0 na Gate-to-Source Reverse Leakage -0 R G Internal Gate Resistance 0.79 Ω Dynamic @ T J = 25 C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Units gfs Forward Transconductance 8.3 S Q g Total Gate Charge 0 Q gs Gate-to-Source Charge 30 nc Q gd Gate-to-Drain ("Miller") Charge 46 t d(on) Turn-On Delay Time 20 t r Rise Time 44 ns t d(off) Turn-Off Delay Time 28 t f Fall Time 5.5 C iss Input Capacitance 2720 C oss Output Capacitance 260 C rss Reverse Transfer Capacitance 20 pf C oss eff. Effective Output Capacitance 20 C oss eff. (ER) Effective Output Capacitance 0 (Energy Related) Avalanche Characteristics Symbol Parameter Typ. Max. Units E AS Single Pulse Avalanche Energyd 320 mj I AR Avalanche Currentc 5 A E AR Repetitive Avalanche Energy c 28 mj Thermal Resistance Symbol Parameter Typ. Max. Units R θjc Junction-to-Caseh 0.44 R θcs Case-to-Sink, Flat, Greased Surface 0.24 C/W R θja Junction-to-Ambienth Conditions V GS = 0V, I D = 250µA Reference to 25 C, I D = ma V GS = V, I D = 9.0A f V DS = V GS, I D = 250µA V DS = 600V, V GS = 0V V DS = 480V, V GS = 0V, T J = 25 C V GS = 30V V GS = -30V f = MHz, open drain Conditions V DS = 50V, I D = 9.0A I D = 5A V DS = 480V V GS = V, See Fig. 7 & 5 f V DD = 300V I D = 5A R G =.8Ω V GS = V, See Fig. a & b f V GS = 0V V DS = 25V ƒ =.0MHz, See Fig. 5 V GS = 0V,V DS = 0V to 480V g Notes: Pulse width 300µs; duty cycle 2%. Repetitive rating; pulse width limited by C oss eff. is a fixed capacitance that gives the same charging time max. junction temperature. (See Fig. ) as C oss while V DS is rising from 0 to 80% V DSS. Starting T J = 25 C, L = 2.9mH, R G = 25Ω, C oss eff.(er) is a fixed capacitance that stores the same energy I AS = 5A, dv/dt = V/ns. (See Figure 2a) as C oss while V DS is rising from 0 to 80% V DSS. ƒ I SD 5A, di/dt 650A/µs, V DD V (BR)DSS, R θ is measured at T J approximately 90 C T J 50 C. 2 www.irf.com 40
I D, Drain-to-Source Current (Α) I D, Drain-to-Source Current (A) R DS(on), Drain-to-Source On Resistance I D, Drain-to-Source Current (A) (Normalized) 00 0 VGS TOP 5V 2V V 9.0V 8.0V 7.0V 6.0V BOTTOM 5.0V 0 VGS TOP 5V 2V V 9.0V 8.0V 7.0V 6.0V BOTTOM 5.0V 5.0V 0. 5.0V 0. 0.0 0.00 20µs PULSE WIDTH Tj = 25 C 0. 0 V DS, Drain-to-Source Voltage (V) 0.0 20µs PULSE WIDTH Tj = 50 C 0. 0 V DS, Drain-to-Source Voltage (V) Fig. Typical Output Characteristics Fig 2. Typical Output Characteristics 00 0 3.0 2.5 I D = 5A V GS = V T J = 50 C 2.0.5 0. 0.0 T J = 25 C V DS = 50V 20µs PULSE WIDTH 4 6 8 2 4 6 V GS, Gate-to-Source Voltage (V).0 0.5 0.0-60 -40-20 0 20 40 60 80 0 20 40 60 T J, Junction Temperature ( C) Fig 3. Typical Transfer Characteristics Fig 4. Normalized On-Resistance vs. Temperature www.irf.com 3
V GS, Gate-to-Source Voltage (V) C, Capacitance(pF) I SD, Reverse Drain Current (A) Energy (µj) 0000 000 V GS = 0V, f = MHZ C iss = C gs C gd, C ds SHORTED C rss = C gd C oss = C ds C gd C iss 25 20 00 5 C oss 0 C rss 5 0 00 0 0 0 200 300 400 500 600 700 V DS, Drain-to-Source Voltage (V) V DS, Drain-to-Source Voltage (V) Fig 5. Typical Capacitance vs. Drain-to-Source Voltage Fig 6. Typ. Output Capacitance Stored Energy vs. V DS 2.0.0 8.0 I D = 5A V DS = 480V V DS = 300V V DS = 20V 0.00.00 T J = 50 C 6.0 4.0.00 T J = 25 C 2.0 0.0 0 20 30 40 50 60 70 Q G Total Gate Charge (nc) V GS = 0V 0. 0.2 0.4 0.6 0.8.0.2.4.6 V SD, Source-to-Drain Voltage (V) Fig 7. Typical Gate Charge vs. Fig 8. Typical Source-Drain Diode Gate-to-Source Voltage Forward Voltage 4 www.irf.com
I D, Drain-to-Source Current (A) Drain Current (A) I D, 00 OPERATION IN THIS AREA LIMITED BY R DS (on) 6 4 0 2 0µsec 8 6 0. Tc = 25 C Tj = 50 C Single Pulse msec msec 0 00 000 V DS, Drain-to-Source Voltage (V) 4 2 0 25 50 75 0 25 50 T C, Case Temperature ( C) Fig 9. Maximum Safe Operating Area Fig. Maximum Drain Current vs. Case Temperature R G V GS V V DS Pulse Width µs Duty Factor 0. % R D D.U.T. - V DD V DS 90% % V GS t d(on) t r t d(off) t f Fig a. Switching Time Test Circuit Fig b. Switching Time Waveforms www.irf.com 5
V GS(th) Gate threshold Voltage (V) Thermal Response ( Z thjc ) D = 0.50 0. 0.0 0.20 0. 0.05 0.02 0.0 P DM 0.00 SINGLE PULSE ( THERMAL RESPONSE ) Notes: t t 2. Duty factor D = t / t 2 2. Peak T J = P DM x Z thjc T C 0.000 E-006 E-005 0.000 0.00 0.0 0. t, Rectangular Pulse Duration (sec) Fig 2. Maximum Effective Transient Thermal Impedance, Junction-to-Case 5.0 4.5 4.0 3.5 I D = 250µA 3.0 2.5 2.0-75 -50-25 0 25 50 75 0 25 50 75 T J, Temperature ( C ) Fig 3. Threshold Voltage vs. Temperature 6 www.irf.com
E AS, Single Pulse Avalanche Energy (mj) 600 500 400 I D TOP 6.7A 9.5A BOTTOM 5A 300 200 0 0 25 50 75 0 25 50 Starting T J, Junction Temperature ( C) Fig 4a. Maximum Avalanche Energy vs. Drain Current 5V V (BR)DSS V DS L DRIVER tp R G 20V tp D.U.T I AS 0.0Ω - V DD A I AS Fig 4b. Unclamped Inductive Test Circuit Current Regulator Same Type as D.U.T. Fig 4c. Unclamped Inductive Waveforms 2V.2µF 50KΩ.3µF D.U.T. V - DS V GS V Q GS Q G Q GD V GS V G 3mA I G I D Current Sampling Resistors Fig 5a. Gate Charge Test Circuit Charge Fig 5b. Basic Gate Charge Waveform www.irf.com 7
Peak Diode Recovery dv/dt Test Circuit D.U.T ƒ - Circuit Layout Considerations Low Stray Inductance Ground Plane Low Leakage Inductance Current Transformer - - R G dv/dt controlled by R G Driver same type as D.U.T. I SD controlled by Duty Factor "D" D.U.T. - Device Under Test - V DD Driver Gate Drive Period P.W. D = P.W. Period V GS =V * D.U.T. I SD Waveform Reverse Recovery Current Body Diode Forward Current di/dt D.U.T. V DS Waveform Diode Recovery dv/dt V DD Re-Applied Voltage Inductor Curent Body Diode Forward Drop Ripple 5% I SD * V GS = 5V for Logic Level Devices Fig 6. For N-Channel HEXFET Power MOSFETs 8 www.irf.com
TO-247AC Package Outline Dimensions are shown in millimeters (inches) TO-247AC Part Marking Information EXAMPLE: THIS IS AN IRFPE30 WITH ASSEMBLY LOT CODE 5657 AS S EMBLED ON WW 35, 2000 IN THE ASSEMBLY LINE "H" Note: "P" in assembly line position indicates "Lead-Free" INT ERNATIONAL RECTIFIER LOGO ASSEMBLY LOT CODE IRFPE30 035H 56 57 PART NUMBER DATE CODE YEAR 0 = 2000 WEEK 35 LINE H TO-247AC package is not recommended for Surface Mount Application. Data and specifications subject to change without notice. This product has been designed and qualified for the Industrial market. Qualification Standards can be found on IR s Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (3) 252-75 TAC Fax: (3) 252-7903 Visit us at www.irf.com for sales contact information.08/04 www.irf.com 9