www.hafeleindia.com www.hafeleindia.com
INTRODUCTION Intuitive furniture is the need of the hour. In times like these where every extra square meter is considered as good as gold, installing versatile home interiors becomes crucial. You will be surprised at the amount of functionality that can be brought in by some intelligent furniture fittings. Häfele brings to you its spontaneous range of Extendable Table Fittings that grants you the liberty to design your dream abode as envisaged and in fact helps create more space. These fittings simply blend into your interiors when closed but once released they end up making quite a statement. Discover Häfele s latest addition to the extendable table fitting range - OPLÀ TOP which is ideal for kitchens with small worktops thus optimizing space. Along with OPLÀ TOP, Häfele reintroduces its efficient and ergonomic extendable table fittings: LUNCH and PARTY MENSOLA. Häfele s range of extendable table fittings consists of : OPLÀ TOP (NEW) : a small fitting that enables the table top to be pulled out of the drawer unit in a manner such that it flushes with the kitchen counter-top. This fitting can be used as a small table for breakfast or as an extension to the kitchen worktops in small kitchens and kitchenettes LUNCH: a small two leaf table top fitting that can be used as a study table in rooms, as a dining table or as an extension to the kitchen worktops in small kitchens and kitchenettes etc. PARTY MENSOLA: a comparatively larger sized, four leaf, table top fitting with a higher weight carrying capacity. It is ideal for use as dining tables in kitchens, as desks in offices etc. This product communication takes you through the following details : TOPIC PAGE NO. OPLA TOP 3 Product Specifications 6 Technical Specifications 7 Installation Specifications 8-11 LUNCH 12 Product Specifications 15 Technical Specifications 16 Installation Specifications 17-18 PARTY MENSOLA 19 Product Specifications 22 Technical Specifications 23 Installation Specifications 24-29 ORDERING INFORMATION 30
This space-saving system enables the table top to be pulled out of the drawer unit in a manner such that it flushes with the kitchen counter-top. Hidden inside a cabinet when not in use, OPLÀ table optimizes space in a small kitchen thus making it Ideal for kitchens with small worktops. It guarantees a very useful additional area to be used as a small table for breakfast or as an extension to the kitchen worktop in small kitchens and kitchenettes
OPLÀTOP : 505.73.934 & 505.73.935 Number of plane : 1 Weight carrying capacity : 40 Kg (evenly distributed) Material (sliding guides) : Aluminum Finish : Stainless Steel Dimensions : 600 mm (width) x 512 mm (length) 900 mm (width) x 512 mm (length) Functioning Steps : Closed Panel pulled out Panel adjusts to the same height as the counter
S ST L2 = Space between the slides L4 = Rod Length L3 = Distance between fixing plane holes L1 = Internal Width TECHNICAL SPECIFICATIONS OPLÀ TOP: 505.73.934 & 505.73.935 General Dimensions: ^ ^ 89.5 mm 52.25 mm Overall Height = 55 mm ^ ^ 89.5 mm 52.25 mm General Cabinet Dimensions: Maximum Length Opened E E1 x H C P Specifications For Width 600 mm For Width 900 mm Side Panel Thickness (L) 18 mm 20 mm 18 mm 20 mm Cabinet Internal Width (L1) = Width (Lx2) 564 mm 560 mm 864 mm 860 mm Space between the slides (L2) = (L1 104.5) 459.5 mm 455.5 mm 759.5 mm 755.5 mm Distance between fixing plane holes (L3) = (L1-179) 385 mm 381 mm 685 mm 681 mm Bar length (L4) 445.5 mm 445.5 mm 745.5 mm 745.5 mm Plane width (Z) = L1 5 559 mm 555 mm 859 mm 855 mm Plane thickness (S) 20 60 mm Min. vertical free space requirement (H) = 60 mm + S Min. internal free space requirement (P) Top thickness (ST) Protrusion (X) : (Refer note 2) Opening plane (E) Complete top length (E1) = (E -X) Opening mechanism (C) : 80 120 mm 540 mm 20 60 mm 18 20 mm 530 mm 510 512 mm 505 mm Note1: Side Thickness of panels can vary from 15-20 mm. The table demonstrated above shows you measurements of 2 commonly used side thicknesses. Note 2: Protrusion (X) depends on the thickness of the side panel, will vary between 15 20 mm.
53 L3 (distance between fixing plane holes) 1 mm Z (plane width) INSTALLATION SPECIFICATIONS OPLÁTOP: 505.73.934 & 505.73.935 Plane Size : 180 151.4 Damper D Ø 12 Ø 10 E1 (Length plane) S (Plane thickness) I Accessories : Damper M6 Brass bushes (Dimension: Ø8 x 12 mm) M5 x 10 Screw Drilling holes for Mechanism Position E = Position of M6 bushes (Dimension of hole to be drilled: Ø 8 x 12) I = Position of M5 x 10 screws for fixing the spacers (Dimension of hole to be drilled : Ø 10 x 5) For cabinet sides less than 20 mm, fix the recommended number of side spacers (included) on to the external slides (optional) J= Side spacers For: Side thickness 20 mm No Spacer Side thickness 19 mm 1 Spacer Side thickness 18 mm 2 Spacers Side thickness 17 mm 3 Spacers Side thickness 16 mm 4 Spacers Side thickness 15 mm 5 Spacers I I E E Here, S = Plane thickness ST =Top thickness Y = Distance of the second bush E from the top Y0 = 68.5 mm (fixed) Note: If the plane thickness (S) and the top thickness (ST) are equal, then the distance of the second bush from the top (Y) will be equal to Y0, i.e. 68.5 mm. However if there is a difference between S and ST, then in that case the difference will be added to Y0 to arrive at Y.
INSTALLATION SPECIFICATIONS OPLÀ TOP: 505.73.934 & 505.73.935 Mounting the mechanism onto the cabinet M6 Brass Bushes (Dimension:Ø8 x 12 mm) As shown in the image, you need to drill four holes (ø 8 13 mm) on each cabinet side for installing the brass bushes. External slide Allen key M5x12 Tapered screw Fix the external slides on to the right side of the cabinet (or vice - versa) by using Socked Head Screws and use the Allen key to tighten them M6x12 Socked head cap screws Place and fix the stabilizing rod with a tapered screw to the attached external slide, as shown in the image Attach the other external slide to the left side of the cabinet (or vice-versa) and to the other end of the stabilizing rod
INSTALLATION SPECIFICATIONS OPLÀ TOP: 505.73.934 & 505.73.935 Fixing the plane to the mechanism M6 Brass Bushes (Dimension:Ø8 x 12 mm) M6x12 Socked head cap screws Washers (Dimension: Ø12x1.35 ) Drill four holes at the bottom side of the plane for installing the brass bushes and two holes on the inner edge for the dampers Mount the plane on to the fixed external slides by placing the washers and using the Socked Head Screws. Tighten them using an Allen key Adjustments The position of the plane can be adjusted in order to achieve a flushed look with the table top. The plane, once partially fixed in position with the Socked Head Screws, can be adjusted vertically for it to reach the table top while the rotating wheel on the external guides can be adjusted clockwise and anti-clockwise in order to flush the plane with the table top. Once the adjustments are done, tighten the Socked Head Screws with an Allen key Attaching the spring and dampers to the fitting Dampers Spring After fixing the plane on the external guides, attach the spring below the plane on both sides, for smooth operation and insert the dampers to achieve seamless transitions of the plane
INSTALLATION SPECIFICATIONS OPLÀ TOP: 505.73.934 & 505.73.935 BOM Components Sliding guides Quantity: 2 Stabilizing rod Quantity: 1 Socked head cap screw (M6x12) Quantity: 12 Washer (Ø12x1.35 ) Quantity: 4 Tapered screw (M5x12) Quantity: 2 M6 Brass bushes (Ø8x12 mm) Quantity: 12 Screw (M5x10 ) Quantity: 8 Side spacers Quantity: 20 Springs Quantity: 2 Dampers Quantity: 2 Allen Key Quantity: 2 Using hinges for the cabinet door To mount the cabinet door, you can use any auto hinge or flap hinge with a magnetic catch of your choice, but its total height should not be more than 18 mm.
This space-saving system consists of a pull-out tabletop fitting stored in a space normally used for a drawer. The table fitting pulls out instantly by simply opening the hinged front of the drawer space. Created to cater to the needs of functionality in small spaces, this runner is ideal for small kitchens and kitchenettes needing a tabletop for breakfast or simply as an extension of the worktop for preparing meals.
PRODUCT SPECIFICATIONS LUNCH : 505.73.944 Number of planes : 2 Weight carrying capacity : 60 Kgs. (evenly distributed) Material (sliding guides) : Natural Anodised Aluminium Finish : Stainless Steel Dimensions : 600 mm (width) 969 mm (length) Functioning Steps : Closed Slides Opening Plane Tilting Push the red locking lever to close the mechanism Opened
(D) (E) (C) (P) TECHNICAL SPECIFICATIONS LUNCH : 505.73.944 (A) (B) (F) Specifications Side Panel Thickness (L) L = 15 mm L = 18 mm L = 20 mm Overall width (A) = 600 (L 2) : 570 mm 564 mm 560 mm Space between the slides (B) : 436 mm 430 mm 426 mm Handle length (C) = A 158 412 mm 406 mm 402 mm Distance between fixing plane holes (D) = A 82 488 mm 482 mm 478 mm Length of sliding guides : 789 mm 789 mm 789 mm Plane Thickness (S) : 18 mm 18 mm 18 mm Width of the planes (P) = 600 [[L 2] + 3] 567 mm 561 mm 557 mm Min. vertical free space requirement (E) = 62 + [S 2] 98 mm 98 mm 98 mm Min. internal free space requirement (F) : 540 mm 540 mm 540 mm Note: Side Thickness of panels can vary from 15-20 mm. The table demonstrated above shows you measurements of 3 commonly used side thicknesses.
INSTALLATION SPECIFICATIONS LUNCH : 505.73.944 Drilling measurements for external slide You need to drill four holes (ø 8 13 mm) on each cabinet side for installing the brass bushes. Brass bushes (included in the pack) Dimension: (ø 8 12 mm) Mounting the mechanism onto the cabinet Screw (M6 x12) Screw (M5 x 6) When this product is delivered to you, the sliding guides come attached as a single mechanism. Hence, in order to mount the mechanism onto the cabinet, it is necessary to first disassemble the two external slides from the rest of the mechanism. To do this, you need to unscrew the two screws in the rear of the second profile. You can now fix the external slides onto the cabinet sides using the included screws (M6 12). Lastly, insert or slide in the mechanism on the mounted external slides and tighten the two screws (one on each side of the second profile). Finally you must screw under the front part of each external slide with (M5x6) screws for additional stability.
INSTALLATION SPECIFICATIONS LUNCH : 505.73.944 Plane dimensions Brass bushes (included in the pack) Dimension: (ø 8 12 mm) Screw (M6 x 60) To install the fixed plane onto the sliding guides, you need to first drill four holes (ø 8 13 mm) under the fixed plane for fitting in the brass bushes. The fixed plane can then be mounted by inserting the screws (M6 60) properly into the holes on the central slide. Note: This system can either be mounted in a cabinet of a base unit or can be mounted in a cabinet that is suspended by the help of wall hanging brackets. In case you wish to suspend the cabinet, you will have to order the wall hanging brackets separately
This new transformable system is designed and engineered down to the smallest detail. It can be mounted in a standard drawer compartment without the need for special fittings, guaranteeing a large-sized (up to approx. 1600 mm) and high capacity (100 Kg equally distributed) table fitting with an integrated telescopic leg.
PRODUCT SPECIFICATIONS PARTY MENSOLA : 642.19.935 Number of planes : 4 Weight carrying capacity : 100 Kgs. (evenly distributed) Material (sliding guides) : Natural Anodised Aluminium Finish : Stainless Steel Dimensions : 900 mm (width) 1794 mm (length) Functioning Steps : A 2. The leg is now free to rotate 4. Pull out the lower part of the leg until you hear a click from the blocking button 1. Turn the lever as indicated 3. Turn the lever as indicated Closed Slides Opening Turning & Extending the Leg Placing the Three Free Top Panels Opened B B Push the red locking lever to close the mechanism
(D) (G) TECHNICAL SPECIFICATIONS PARTY MENSOLA : 642.19.935 (B) (H) (F) (C) (B) (A) Specifications Side Panel Thickness (L) 15 mm 18 mm 20 mm Overall width (A) = 900 (L 2) : 870 mm 864 mm 860 mm Minimum Cabinet Depth (B) : 502 mm 502 mm 502 mm Minimum Cabinet Height (C) : 155 mm 155 mm 155 mm Width of the Planes (D) : 838 mm 832 mm 828 mm Complete Top Length (E) : 1794 mm 1794 mm 1794 mm Total Length Outside the Cabinet (F) : 1562 mm 1562 mm 1562 mm Table Top Height (G) : 733 mm 733 mm 733 mm Plane Thickness (S) : 18 mm 18 mm 18 mm Min. vertical free space requirement (H) = 80 + [S 4] 152 mm 152 mm 152 mm Note: Side Thickness of panels can vary from 15-20 mm. The table demonstrated above shows you measurements of 3 commonly used side thicknesses.
INSTALLATION SPECIFICATIONS PARTY MENSOLA : 642.19.935 Drilling measurements for slide installation Brass bushes (included in the pack) Dimension: (ø 8 12 mm) You need to drill four holes (ø 8 13 mm) on each cabinet side for installing the brass bushes. Attaching the leg to the sliding guide Screw (M6 x 12) Before installing the mechanism into the cabinet, you need to fix the extendable leg onto the sliding guide. TPS Screw (M6 x16)
INSTALLATION SPECIFICATIONS PARTY MENSOLA : 642.19.935 Separating the external guide from the mechanism When this product is delivered to you, the sliding guides come attached as a single mechanism. Hence, in order to mount the mechanism onto the cabinet, it is necessary to first disassemble the two external slides from the rest of the mechanism. To do this follow the below mentioned steps. 2. Unscrew the two screws in the rear of the first central profile. 1. Unscrew the two screws under the external slide Fixing the lateral bar and external slide to the cabinet sides Lateral Bar External Slide Screw (M6 x 12) In order to mount the mechanism onto the cabinet, you will first have to fix the Lateral Bar to the internal cabinet sides using an Allen key and 4 screws (M6 12). Using the same Allen key, fix the external slide to the lateral by with another 4 screws (M6 12).
INSTALLATION SPECIFICATIONS PARTY MENSOLA : 642.19.935 Mounting the mechanism onto the cabinet 1. Tighten the two screws in the rear of the first central profile. Slide in the mechanism on the mounted external slides. Tighten the screw on each side when the end of the first central slide is about 250 mm from the back of the external slide. Once that is done tighten the two screws under the external slide. 2. Tighten the two screws under the external slide Assembly of the top fixed plane Female Pin Brass bushes (included in the pack) Dimension: (ø 8 12 mm) Screw (M6 x 60) To install the fixed plane onto the sliding guides, you need to first drill four holes (ø 8 13 mm) under the fixed plane for fitting in the brass bushes. The fixed plane is then ready to be mounted on the sliding guides by inserting the four screws (M6 60) properly into the holes on the central slide. Before you assemble the fixed plane onto the sliding guide, you need to also drill three holes (as per the dimensions mentioned below) on the front side of the fixed plane (the side that will face the central plane) in order to insert the female centering pins. Side Panel Thickness 15 mm 18 mm 20 mm X 350 mm 350 mm X Distance from the edge (X) 63 mm 66 mm 68 mm
INSTALLATION SPECIFICATIONS PARTY MENSOLA : 642.19.935 Assembly of the top central planes (2) You need to drill 3 holes in the back side of the center planes to insert the male centering pins. These male centering pins fit perfectly into the hollow female centering pins inserted in the front side of the fixed / central planes Female Pin Male Pin Drill 3 holes in the front side of the center planes to insert the female centering pins. Assembly of the final top plane Male Pin You need to drill 3 holes in the back side of the final top plane to insert the male centering pins. Plastic Locking Clip Two plastic locking clips need to be installed under the final top plane. These locking clips get secured onto the protrusions present on either sides of the sliding guides, thereby anchoring and stabilising the entire table extension. Note: Dimensions for drilling the male and female centering pins remain the same as demonstrated in the table on pg. 17
INSTALLATION SPECIFICATIONS PARTY MENSOLA : 642.19.935 Alternative to using male and female centering pins for joining planes If you do not prefer using the male and female centering pins for the purpose of joining the planes, you could use hinges like in LUNCH. The two options are: Article No.:341.07.718 Concealed Hinge, Opening Angle180, Nickel Plated, For 13 to 19 mm thick panel For Wood Thickness (mm) 13-19 Dim. A Dim. B Dim. C Dim. D Dim. E Gap F Gap G Gap H 9.6 mm 43 mm 22 mm 5.5 mm 6 mm 17.1 mm 2.4 mm 2.7 mm Article No.:341.31.519 Folding Leaf Hinge, Zinc Alloy, Yellow Chromatised, For 18 to 19 mm thick panel Note: The BOM for PARTY MENSOLA includes the male and female centering pins as the default option. In case you wish to install hinges, you will have to order them separately You will have to use 3 hinges to join two planes, hence you will have to order 9 hinges for connecting all the planes to each other Please keep in mind that since the planes, with the use of hinges, will be connected to each other, it will make folding and unfolding of the planes a strenuous activity
INSTALLATION SPECIFICATIONS PARTY MENSOLA : 642.19.935 Using hinges for the frontal cabinet door To mount the frontal cabinet door, you can use hinges of your choice but its final height should not be more than 18 mm. Alternatively you could also use flap hinges for a flushed look as demonstrated below: Positioning of the felts under the top planes 3 2 1 Place the 12 felts over the top of the sliding guides with the adhesive side facing upwards. Place the two central and the final top plane in their positions following the indicated sequence so that the felts get glued onto their proper positions on the bottom of the three top planes. Felts Note: This system can either be mounted in a cabinet of a base unit or can be mounted in a cabinet that is suspended by the help of wall hanging brackets. In case you wish to suspend the cabinet, you will have to order the wall hanging brackets separately
ORDERING INFORMATION Extendable Table Fittings Article Number Description MRP (INR) OPLÀ TOP Dimensions: 600 mm (width) x 512 (length) Consists of : 505.73.934 Pair of Sliding Guides Stabilizing Rod Spacers and Fastening Material 33,333/- Damper OPLÀ TOP Dimensions: 900 mm (width) x 512 (length) Consists of : Pair of Sliding Guides 34,100/- 505.73.935 Stabilizing Rod Spacers and Fastening Material 505.73.944 LUNCH Extension Table Fittings Dimensions: 600 mm (width) 969 mm (length) Consists of: Damper Pair of Sliding Guides Handle (can be cut to size as per the side panel thickness) Fastening Material 29,465/- Article No.:341.07.718, Concealed Hinges 642.19.935 PARTY MENSOLA Extension Table Fittings Dimensions: 900 mm (width) 1794 mm (length) Consists of: Assembled Mechanism Pair of Lateral Bar Fastening Material Plastic Locking Clips Male and Female Centering Pins 96,540/- Accessories: PARTY MENSOLA Article Number Description MRP (INR) 341.07.718 Concealed Hinge, Opening Angle180, Nickel Plated, For 13 to 19 mm thick panel 979/- 341.31.519 Folding Leaf Hinge, Zinc Alloy, Yellow Chromatised, For 18 to 19 mm thick panel 732/- 642.51.243 Male and Female Centering Pins (only if additional pieces are required) 14/-
Häfele India Private Limited Office No. 3, Building A, BETA, I Think Techno Campus, Off J.V.L.R, Opp. Kanjurmarg East, Mumbai 400 042. Tel.: 022 6142 6100 Fax: 022 6702 0531 New Delhi Kolkata Chennai Hyderabad Bangalore Pune Ahmedabad Srilanka Bangladesh Nepal Bhutan Toll Free Customer Care No.:1800 266 6667 SMS HAFELE to 56070 customercare@hafeleindia.com www.hafeleindia.com