(Wood Door and Frame)

ITS961 and ITS965 Closer in Door Track in Frame (Wood Door and Frame) 1 (REFERENCE UNIT CARTON FOR ACCESSORIES AND OPTIONS SUPPLIED) Determine hand of door. Prepare door and frame according to template for ITS961 or ITS965. If 000 accessory track brackets are used, refer to appropriate template. Adjust spring tension. CRITICAL NOTE: Clockwise turns increase spring tension. NOTE: MAXIMUM NUMBER OF TURNS 17 5MM HEX WRENCH BARRIERFREE OPENINGS Adjust only if more tension is required to close and latch the door. Depending on opening conditions, a door adjusted to meet barrierfree forces may not have sufficient power to reliably close and latch the door. NONBARRIERFREE OPENINGS Adjust according to chart. LEFT HAND DOOR RIGHT HAND DOOR The ITS 96 is UL listed for use on fire doors. Refer to door and frame manufacturer to determine if preperation is listed for fire door applications. FULL TURNS MAXIMUM FULL TURNS OF SPRING OF SPRING DOOR WT. ADJUSTER ADJUSTER (LBS) ITS961 ITS965 '6" 100 '0" 15 15 5 '6" 150 0 '0" 175 5 DOOR WIDTH (INTERIOR) SPRING SIZE Thread screw a few turns into the deadstop block. Insert components into track as shown. Fasten track to frame. DEADSTOP BLOCK SLIDE SHOE TRACK BRACKETS (OPTIONAL) Part No. 000 DEADSTOP ASSEMBLY HINGE HOLD OPEN (OPTIONAL) NOTE: ARROWS ON HOLD OPEN AND SLIDE SHOE, MUST POINT AWAY FROM HINGE WHEN INSTALLING IN TRACK. Place arm on closer according to hand of door. Secure arm with pinion screw. PINION SCREW 5mm R.H. L.H. INSPK NO. 07960 Rev.06/0 www.dormausa.com 1005 INS NO. 07961 PAGE 1 of Rev. 0/11

5 Close valve by turning completely clockwise. Rotate arm 5. Adjust deadstop. Open door to desired opening between 0 and 10. Tighten deadstop block. 5 The deadstop helps to prevent damage to the door and wall when the door is opened normally. The deadstop is not abuse resistant, and cannot replace a door stop in many situations. Deadstop is adjustable between 0 and 10 maximum. 9 Adjust sweep and latch valves. 6 Attach closer to door. CAUTION: DO NOT REMOVE VALVES () () (INCREASE ONLY) 7 Align hole in arm with slide shoe and attach with screw provided. SCREW 5mm 6mm ON HOLD OPEN UNITS INS NO. 07961 PAGE of Rev. 0/11

10 (HOLD OPEN UNITS ONLY) Set hold open. A Place the hold open mechanism in desired position. Tighten screws #1 and # securely. 1 C To enable hold open, push the white slide into the hold open mechanism. To disable hold open, pull the white slide away from hold open mechanism. M.5 ON OFF B To adjust hold open force, turn clockwise to increase force, and counter clockwise to weaken force. M.5 INS NO. 07961 PAGE of Rev. 0/11

ITS961 AND ITS965 OHC Closer in Frame Track in Door 1 (REFERENCE UNIT CARTON FOR ACCESSORIES AND OPTIONS SUPPLIED) (Wood Door and Frame) Adjust spring tension. Determine hand of door. Prepare door and frame according to template for ITS961 or ITS965. CRITICAL NOTE: Clockwise turns increase spring tension. NOTE: MAXIMUM NUMBER OF TURNS 17 5MM HEX WRENCH LEFT HAND DOOR RIGHT HAND DOOR BARRIERFREE OPENINGS Adjust only if more tension is required to close and latch the door. Depending on opening conditions, a door adjusted to meet barrierfree forces may not have sufficient power to reliably close and latch the door. NONBARRIERFREE OPENINGS Adjust according to chart. The ITS 96 is UL listed for use on fire doors. Refer to door and frame manufacturer to determine if preperation is listed for fire door applications. FULL TURNS MAXIMUM FULL TURNS OF SPRING OF SPRING DOOR WT. ADJUSTER ADJUSTER (LBS) ITS961 ITS965 '6" 100 '0" 15 15 5 '6" 150 0 '0" 175 5 DOOR WIDTH (INTERIOR) SPRING SIZE Place arm on closer according to hand of door. Attach arm with pinion screw. R.H. L.H. PINION SCREW 5mm Close valve by turning completely clockwise. Rotate arm 5 and attach closer to frame. R.H. 5 5 L.H. HINGE INSPK NO. 079650 Rev.1/09 www.dormausa.com 1005 INS NO. 079651 PAGE 1 of Rev. 0/11

5 Thread screw a few turns into deadstop block. Insert components into track. Fasten track to door. 7 Open door to desired opening between 0 and 10. Tighten deadstop block. DEADSTOP BLOCK DEADSTOP ASSEMBLY SLIDE SHOE The deadstop helps to prevent damage to the door and wall when the door is opened normally. The deadstop is not abuse resistant, and cannot replace a door stop in many situations. Deadstop is adjustable between 0 and 10 maximum. Adjust sweep and latch valves. CAUTION: DO NOT REMOVE VALVES HOLD OPEN (OPTIONAL) NOTE: ARROWS ON HOLD OPEN AND SLIDE SHOE, MUST POINT AWAY FROM HINGE WHEN INSTALLING IN TRACK. () 6 Align hole in arm with slide shoe and attach with screw provided. 5mm () (INCREASE ONLY) SCREW 6mm HOLD OPEN UNITS ONLY INS NO. 079651 PAGE of Rev. 0/11

9 (HOLD OPEN UNITS ONLY) Set hold open. A Place the hold open mechanism in desired position. Tighten screws #1 and # securely. M.5 C To enable hold open, push the white slide into the hold open mechanism. To disable hold open, pull the white slide away from hold open mechanism. 1 B To adjust hold open force, turn clockwise to increase force, and counter clockwise to weaken force. M.5 OFF ON INS NO. 079651 PAGE of Rev. 0/11

ITS961 and ITS965 Closer in Door Track in Frame (Metal Door and Frame) 1 (REFERENCE UNIT CARTON FOR ACCESSORIES AND OPTIONS SUPPLIED) Determine hand of door. Prepare door and frame according to template for ITS961 or ITS965. If 0010 accessory track brackets are used, refer to appropriate template. LEFT HAND DOOR RIGHT HAND DOOR The ITS 96 is UL listed for use on fire doors. Refer to door and frame manufacturer to determine if preperation is listed for fire door applications. Adjust spring tension. CRITICAL NOTE: Clockwise turns increase spring tension. NOTE: MAXIMUM NUMBER OF TURNS 17 5MM HEX WRENCH BARRIERFREE OPENINGS Adjust only if more tension is required to close and latch the door. Depending on opening conditions, a door adjusted to meet barrierfree forces may not have sufficient power to reliably close and latch the door. NONBARRIERFREE OPENINGS Adjust according to chart. FULL TURNS MAXIMUM FULL TURNS DOOR WIDTH OF SPRING OF SPRING SPRING (INTERIOR) DOOR WT. ADJUSTER ADJUSTER SIZE (LBS) ITS961 ITS965 '6" 100 '0" 15 15 5 '6" 150 0 '0" 175 5 Thread screw a few turns into the deadstop block. Insert components into track as shown. Fasten track to frame. DEADSTOP BLOCK SLIDE SHOE TRACK BRACKETS (OPTIONAL) Part No. 0010 DEADSTOP ASSEMBLY HINGE HOLD OPEN (OPTIONAL) NOTE: ARROWS ON HOLD OPEN AND SLIDE SHOE, MUST POINT AWAY FROM HINGE WHEN INSTALLING IN TRACK. Place arm on closer according to hand of door. Secure arm with pinion screw. PINION SCREW 5mm R.H. L.H. www.dormausa.com 1005 INSPK NO. 07960 Rev.06/0 INS NO. 07961 PAGE 1 of Rev. 0/11

5 Close valve by turning completely clockwise. Rotate arm 5. Adjust deadstop. Open door to desired opening between 0 and 10. Tighten deadstop block. 5 The deadstop helps to prevent damage to the door and wall when the door is opened normally. The deadstop is not abuse resistant, and cannot replace a door stop in many situations. Deadstop is adjustable between 0 and 10 maximum. 9 Adjust sweep and latch valves. 6 Attach closer to door. CAUTION: DO NOT REMOVE VALVES () () (INCREASE ONLY) 7 Align hole in arm with slide shoe and attach with screw provided. SCREW 5mm 6mm ON HOLD OPEN UNITS INS NO. 07961 PAGE of Rev. 0/11

10 (HOLD OPEN UNITS ONLY) Set hold open. A Place the hold open mechanism in desired position. Tighten screws #1 and # securely. 1 C To enable hold open, push the white slide into the hold open mechanism. To disable hold open, pull the white slide away from hold open mechanism. M.5 ON OFF B To adjust hold open force, turn clockwise to increase force, and counter clockwise to weaken force. M.5 INS NO. 07961 PAGE of Rev. 0/11

ITS961 AND ITS965 OHC Closer in Frame Track in Door 1 (REFERENCE UNIT CARTON FOR ACCESSORIES AND OPTIONS SUPPLIED) (Metal Door and Frame) Adjust spring tension. Determine hand of door. Prepare door and frame according to template for ITS961 or ITS965. CRITICAL NOTE: Clockwise turns increase spring tension. NOTE: MAXIMUM NUMBER OF TURNS 17 5MM HEX WRENCH LEFT HAND DOOR RIGHT HAND DOOR BARRIERFREE OPENINGS Adjust only if more tension is required to close and latch the door. Depending on opening conditions, a door adjusted to meet barrierfree forces may not have sufficient power to reliably close and latch the door. NONBARRIERFREE OPENINGSAdjust according to chart. The ITS 96 is UL listed for use on fire doors. Refer to door and frame manufacturer to determine if preperation is listed for fire door applications. FULL TURNS MAXIMUM FULL TURNS OF SPRING OF SPRING DOOR WT. ADJUSTER ADJUSTER (LBS) ITS961 ITS965 '6" 100 '0" 15 15 5 '6" 150 0 '0" 175 5 DOOR WIDTH (INTERIOR) SPRING SIZE Place arm on closer according to hand of door. Attach arm with pinion screw. R.H. L.H. PINION SCREW 5mm Close valve by turning completely clockwise. Rotate arm 5 and attach closer to frame. R.H. 5 5 L.H. HINGE INSPK NO. 07960 Rev.1/09 www.dormausa.com 1005 INS NO. 07961 PAGE 1 of Rev. 0/11

5 Thread screw a few turns into deadstop block. Insert components into track. Fasten track to door. 7 Open door to desired opening between 0 and 10. Tighten deadstop block. DEADSTOP BLOCK DEADSTOP ASSEMBLY The deadstop helps to prevent damage to the door and wall when the door is opened normally. The deadstop is not abuse resistant, and cannot replace a door stop in many situations. Deadstop is adjustable between 0 and 10 maximum. SLIDE SHOE Adjust sweep and latch valves. CAUTION: DO NOT REMOVE VALVES HOLD OPEN (OPTIONAL) NOTE: ARROWS ON HOLD OPEN AND SLIDE SHOE, MUST POINT AWAY FROM HINGE WHEN INSTALLING IN TRACK. () 6 () (INCREASE ONLY) Align hole in arm with slide shoe and attach with screw provided. 5mm SCREW 6mm HOLD OPEN UNITS ONLY INS NO. 07961 PAGE of Rev. 0/11

9 (HOLD OPEN UNITS ONLY) Set hold open. A Place the hold open mechanism in desired position. Tighten screws #1 and # securely. M.5 C To enable hold open, push the white slide into the hold open mechanism. To disable hold open, pull the white slide away from hold open mechanism. 1 B To adjust hold open force, turn clockwise to increase force, and counter clockwise to weaken force. M.5 OFF ON INS NO. 07961 PAGE of Rev. 0/11