3 Series Product description
Contents: 3 Series - overview and advantages Special features of Series 3 Sensor selection table Data sheets All rights reserved, especially the rights of copying and translation. Copying or reproduction in any form requires prior written permission from Leuze electronic GmbH + Co. KG Subject to changes due to technical progress.
3 Series Overview and advantages Small construction series in robust plastic housing Operating principles: - Throughbeam photoelectric sensors - Retro-reflective photoelectric sensors - Retro-reflective photoelectric sensors with polarisation filter - Energetic diffuse reflection light scanners - Diffuse reflection light scanners with background suppression Visible red light for fast and easy alignment High switching frequency up to 2000kHz for detection of fast events 10 30VDC voltage with PNP transistor output or pushpull output - M8/M12 connector for fast installation - Cable models for installation locations with limited space Options: - Warning output - Activation input - Teach-in via button (lockable) or teach input 1
2 Leuze electronic
Special features of Series 3 Small, compact and competitively priced sensors Versatile and easy to integrate - Small, compact construction - IP 67 and IP 69K - Active suppression of extraneous light A²LS - Simple alignment with visible red light - Reliable mounting with inset metal sleeves - Application-specific, special solutions available, e.g. diffuse reflection scanner with elongated light spot Throughbeam photoelectric sensors Advantage 1: Visible light spot Advantage 2: Large operating range Advantage 3: Suppression of reflector problems Advantage 4: Very comfortable alignment Advantage 5: With activation input for muting function A 2 LS Retro-reflective photoelectric sensors with polarisation filter Advantage 1: Highest functional reliability through active ambient light suppression A²LS Advantage 2: High performance reserve Advantage 3: Special models with autocollimation principle available Retro-reflective photoelectric sensors for detection of glass, PET, and foils. Advantage 1: Easy setting via lockable teach button or teach input Advantage 2: Push-pull output with light/dark switching via teach button Advantage 3: Retro-reflective photoelectric sensor without polarisation filter may also be used with glass reflectors (TG) Laser retro-reflective photoelectric sensors Advantage 1: Polarised retro-reflective photoelectric sensor with autocollimation principle Advantage 2: Laser safety class 1 Advantage 3: High switching frequency for detection of fast events and small parts Energetic diffuse reflection light scanners Advantage 1: Simple contrast detection Advantage 2: Adjustable via potentiometer Advantage 3: Long scanning range Diffuse reflection light scanners with background suppression Advantage 1: Mechanical background suppression Advantage 2: Very good black/white behaviour Advantage 3: Application-specific, special solutions available, e.g. diffuse reflection scanner with elongated light spot 3
Sensor selection table Operating principle Designation Typ. oper. range limit/ typ. scan. range limit Housing Light source Operating voltage Output Frequency Plastic Red light Red light, Laser class 1 10 30VDC PNP transistor NPN transistor Push-Pull LSR 3/44.8-S8 0 8500mm 1000Hz LSR 3/44.8 0 8500mm 1000Hz ILSR 3/4.8-S8 0 8500mm 1000Hz LSR 3/44.8, 5000 0 8500mm 1000Hz LSR 3/22.8-S8 0 8500mm 1000Hz ILSR 3/4.8 0 8500mm 1000Hz ILSR 3/4.8, 200-S8 0 8500mm 1000Hz PRK 3B/66 20 6000mm 1000Hz PRK 3B/66-S8 20 6000mm 1000Hz PRK 3B/66, 200-S8 20 6000mm 1000Hz PRK 3B/66, 200-S12 20 6000mm 1000Hz PRK 3B/6.7 20 6000mm 1000Hz PRK 3B/6.7-S8 20 6000mm 1000Hz PRK 3B/6.22 0 5000mm 1000Hz PRK 3B/6.22-S8 0 5000mm 1000Hz PRK 3B/6.22, 200-S8 0 5000mm 1000Hz RKR 3B/6.42 0 1800mm 1000Hz RKR 3B/6.42-S8 0 1800mm 1000Hz RKR 3B/6.42, 200-S8 0 1800mm 1000Hz PRKL 3B/6.22 0 3000mm 2000Hz PRKL 3B/6.22-S8 0 3000mm 2000Hz PRKL 3B/6.22, 200-S8 0 3000mm 2000Hz RTR 3/22-300-S8 5 500mm 1000Hz RTR 3/44-300-S8 5 500mm 1000Hz RTR 3/44-300 5 500mm 1000Hz HRTR 3/44-150-S8 7 180mm 1000Hz HRTR 3/44-150 7 180mm 1000Hz HRTR 3/22-150 7 180mm 1000Hz HRTR 3/22-150-S8 7 180mm 1000Hz HRTR 3/44-150, 5000 7 180mm 1000Hz HRTR 3/44-65-S8 7 180mm 1) 1000Hz HRTR 3/4-150, 200-S8 7 180mm 1000Hz HRTR 3/44-150, 150-S12 7 180mm 1000Hz HRTR 3/44-50-S8 5 150mm 2) 500Hz HRTR 3/44-50,150-S12 5 150mm 2) 500Hz 1) Scanning range preset to 65mm 2) Special light spot 3x40mm at 50mm 4
Switching Connection Options Page Light switching Dark switching Cable M8 connector Cable with M8 connector Cable with M12 connector Warning output Activation input 7 7 7 7 7 7 9 Background suppression Polarisation filter Sensitivity adjustment via potentiometer Sensitivity adjustment via teach button or teach input Transparent media Focussed light beam Direct connection to AS-i I/O coupling modules 12 12 12 12 15 15 18 18 18 24 24 24 30 30 30 37 37 37 39 39 39 39 39 39 41 43 45 45 5
Specifications and description Leuze electronic LSR 3 Throughbeam photoelectric sensors Dimensioned drawing 8.5m 10-30 V DC! Throughbeam photoelectric sensor with high performance reserve in red light! Small construction with robust plastic housing, protection class IP 67/IP 69K for industrial application! High switching frequency for detection of fast events! Complementary switching outputs for light/ dark switching or as a control function! Warning output autocontrol for increased availability U L US C LISTED A Optical axis B Adjustment screw only receiver C Indicator diode only receiver Electrical connection We reserve the right to make changes 3_a01e.fm IEC 60947... IEC 60947... Accessories: IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! M8 connectors (D M8A )! Ready-made cables (K-D ) Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 6 LSR 3/44.8/5000/-S8-04 ILSR 3/4.8-S8-04
LSR 3 Specifications Optical data Typ. operating range limit 1) 0 8.5m Operating range 2) 0 6m Light source (modulated light) Wavelength 660nm (visible red light) Timing Switching frequency 1000Hz Response time 0.5ms Delay before start-up 100ms Electrical data Operating voltage U B 10 30VDC (incl. residual ripple) Residual ripple 15% of U B Bias current 25mA Switching output 2 transistor outputs, complementary Function characteristics light/dark switching Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Sensitivity adjustable with multiturn potentiometer Indicators yellow light path free yellow flashing light path free, no performance reserve Mechanical data Housing plastic Optics cover plastic (PMMA) Weight 20g Connection type M8 connector (4-pin) or PUR cable 2m and 5m (cross section 4x0.2mm²) Environmental data Ambient temp. (operation/storage) -25 C +55 C/-40 C +70 C Protective circuit 3) 2, 3 VDE safety class 4) II, all-insulated Protection class IP 67, IP 69K 5) class 1 (acc. to EN 60825-1) Standards applied IEC 60947-5-2 Options Activation input activ Transmitter active/not active 8V/ 2V or not connected Activation/disable delay 1ms Input resistance 4.7kΩ ±10% Warning output autocontrol warn PNP transistor, counting principle Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA 1) Typ. operating range limit: max. attainable range without performance reserve 2) Operating range: recommended range with performance reserve 3) 2=polarity reversal protection, 3=short-circuit protection for all outputs 4) Rating voltage 250VAC 5) IP 69K test acc. to DIN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Order guide Selection table Order code " LSR 3/44.8 Part No. 500 30996 (Tr) Part No. 500 31276 (Re) LSR 3/44.8, 5000 Part No. 500 33654 (Tr) Part No. 500 33653 (Re) LSR 3/44.8-S8 Part No. 500 30995 (Tr) Part No. 500 31275 (Re) ILSR 3/4.8-S8 Part No. 500 30995 (Tr) Part No. 500 30915 (Re) LSR 3/22.8-S8 Part No. 500 30995 (Tr) Part No. 500 37975 (Re) ILSR 3/4.8 Part No. 500 30996 (Tr) Part No. 500 30916 (Re) Equipment # Switching output 2xPNP transistor (Re)!!! 2xNPN transistor (Re)! 1xPNP transistor (Re)!! light/dark switching!!!! light switching!! Connection M8 connector!!! cable 5000mm! cable 2000mm!! Features activation input (Tr)!!!!!! warning output!! Tables 0 6.0 8.5 Operating range [m] Typ. operating range limit [m] Diagrams Misalignment y [mm] Typ. response behaviour 200 150 100 y2 50 0-50 y1-100 -150-200 0 1 2 3 4 5 6 7 8 9 Distance x [m] x y2 y1 Remarks [I]LSR = Pair consisting of LSSR = Transmitter [I]LSER = Receiver LSR 3/44.8 LSSR 3.8 LSER 3/44 LSR 3/44.8, 5000 LSSR 3.8, 5000 LSER 3/44, 5000 LSR 3/44.8-S8 LSSR 3.8-S8 LSER 3/44-S8 ILSR 3/4.8-S8 LSSR 3.8-S8 ILSER 3/4-S8 LSR 3/22.8-S8 LSSR 3.8-S8 LSER 3/22-S8 ILSR 3/4.8 LSSR 3.8 ILSER 3/4 LSR 3/44.8/5000/-S8-04 0605 ILSR 3/4.8-S8-04 7
Specifications and description Leuze electronic LSR 3 Throughbeam photoelectric sensors Dimensioned drawing 8.5m 10-30 V DC! Throughbeam photoelectric sensor with high performance reserve in red light! Small construction with robust plastic housing, protection class IP 67/IP 69K for industrial application! High switching frequency for detection of fast events! Warning output autocontrol for increased availability A Optical axis B Adjustment screw only receiver C Indicator diode only receiver Electrical connection We reserve the right to make changes 3_a02e.fm IEC 60947... IEC 60947... Accessories: IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! M8 connectors (D M8A )! Ready-made cables (K-D ) Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 8 LSSR 3.8,200-S8-03 ILSER 3/4,200-S8-03
LSR 3 Specifications Optical data Typ. operating range limit 1) 0 8.5m Operating range 2) 0 6m Light source (modulated light) Wavelength 660nm (visible red light) Timing Switching frequency 1000Hz Response time 0.5ms Delay before start-up 100ms Electrical data Operating voltage U B 10 30VDC (incl. residual ripple) Residual ripple 15% of U B Bias current 25mA Switching output 1 PNP transistor output Function characteristics light switching Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Sensitivity adjustable with multiturn potentiometer Indicators yellow light path free yellow flashing light path free, no performance reserve Mechanical data Housing plastic Optics cover plastic (PMMA) Weight 20g Connection type M8 connector (4-pin) with 200mm cable tail Environmental data Ambient temp. (operation/storage) -25 C +55 C/-40 C +70 C Protective circuit 3) 2, 3 VDE safety class 4) II, all-insulated Protection class IP 67, IP 69K 5) class 1 (acc. to EN 60825-1) Standards applied IEC 60947-5-2 Options Activation input activ Transmitter active/not active 8V/ 2V or not connected Activation/disable delay 1ms Input resistance 4.7kΩ ±10% Warning output autocontrol warn PNP transistor, counting principle Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA 1) Typ. operating range limit: max. attainable range without performance reserve 2) Operating range: recommended range with performance reserve 3) 2=polarity reversal protection, 3=short-circuit protection for all outputs 4) Rating voltage 250VAC 5) IP 69K test acc. to DIN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Tables 0 6.0 8.5 Operating range [m] Typ. operating range limit [m] Diagrams Misalignment y [mm] Typ. response behaviour 200 150 100 y2 50 0-50 y1-100 -150-200 0 1 2 3 4 5 6 7 8 9 Distance x [m] x y2 y1 Remarks Order guide Designation Transmitter and receiver ILSR 3/4.8, 200-S8 Part No. Transmitter with 200mm cable and M8 connector Receiver with 200mm cable and M8 connector LSSR 3.8,200-S8 500 41888 ILSER 3/4,200-S8 500 41887 LSSR 3.8,200-S8-03 0605 ILSER 3/4,200-S8-03 9
Specifications and description Leuze electronic PRK 3B Retro-reflective photoelectric sensors with polarisation filter Dimensioned drawing 1 khz 0.02 6m 10-30 V DC A 2 LS! Polarised retro-reflective photoelectric sensor with visible red light! High performance reserve! Small and compact construction with robust plastic housing, protection class IP 67/ IP 69K for industrial application! Fast alignment through brightvision! A²LS - Active Ambient Light Suppression! Push-pull switching outputs! High switching frequency for detection of fast events! Warning output for increased availability A B C D Indicator diode green Indicator diode yellow Optical axis Attachment sleeve U L US C LISTED Electrical connection We reserve the right to make changes 3B_b01e.fm IEC 60947... IEC 60947... Accessories: IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! Cable with M8 or M12 connector (K-D )! Reflectors! Reflective tapes Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 10 PRK 3B/4, /4D - 01 PRK 3B/6, /6D, /66-01
PRK 3B Specifications Optical data Typ. op. range limit (TK(S) 100x100) 1) Operating range 2) Light source 3) Wavelength Timing Switching frequency Response time Delay before start-up Electrical data Operating voltage U 4) B Residual ripple Bias current Switching output 5) /66 Function characteristics Signal voltage high/low Output current Sensitivity Indicators green yellow yellow flashing Mechanical data Housing Optics cover Weight Connection type Environmental data Ambient temp. (operation/storage) Protective circuit 7) VDE safety class 8) /6 /6D /4 /4D 0.02 6m see tables (modulated light) 620nm (visible red light, polarised) 1000Hz 0.5ms 300ms 10 30VDC (incl. residual ripple) 15% of U B 14mA 2 push-pull switching outputs pin 2: PNP dark switching, NPN light switching pin 4: PNP light switching, NPN dark switching 1 push-pull switching output pin 4: PNP light switching, NPN dark switching 1 push-pull switching output pin 4: PNP dark switching, NPN light switching 1 PNP switching output light switching, 1 warning output 1 PNP switching output dark switching, pin 2: not connected 6) light/dark switching (U B -2V)/ 2V max. 100mA fixed setting ready light path free light path free, no performance reserve plastic (PC-ABS); 1 attachment sleeve, nickel-plated steel plastic (PMMA) with connector: 10g with 200mm cable and connector: 20g with 2m cable: 50g cable 2m (cross section 4x0.21mm²), connector M8 metal, cable 0.2m with connector M8 or M12-30 C +55 C/-30 C +70 C 2, 3 II for cable, III for metal plug IP 67, IP 69K Protection class class 1 (acc. to EN 60825-1) Standards applied IEC 60947-5-2 Certifications UL 508 4) Options Warning output autocontrol warn Signal voltage high/low Output current PNP transistor, counting principle (U B -2V)/ 2V max. 100mA 1) Typ. operating range limit: max. attainable range without performance reserve 2) Operating range: recommended range with performance reserve 3) Average life expectancy 100'000h at an ambient temperature of 25 C 4) For UL applications: for use in class 2 circuits according to NEC only 5) The push-pull switching outputs must not be connected in parallel 6) Pin 2: unassigned, hence especially suitable for the connection to AS-interface I/O coupling modules 7) 2=polarity reversal protection, 3=short-circuit protection for all transistor outputs 8) Rating voltage 50V Tables Reflectors Operating range 1 TK(S) 100x100 0.02 5.0m 2 TK 40x60 0.02 3.0m 3 TK 20x40 0.02 1.5m 4 Tape 4 50x50 0.02 1.2m 1 0.02 5 6 2 0.02 3 3.6 3 0.02 1.5 2 4 0.02 1.2 1.6 Operating range [m] Typ. operating range limit [m] TK TKS = adhesive = screw type Diagrams Misalignment y [mm] Performance reserve -100-150 0 1 2 3 4 5 6 Distance x [m] A B C D 150 100 50 0-50 65 60 55 50 45 40 35 30 25 20 15 10 5 0 x Typ. response behaviour y2 y1 TK 100x100 TKS 40x60 TKS 20x40 Tape 4: 50x50 y2 y1 Typ. performance reserve A B C D 0 1 2 3 4 5 6 Remarks Distance x [m] Mounting system: ➀ ➁ ➂ PRK 3B/4, /4D - 01 0605 PRK 3B/6, /6D, /66-01 11 ➀ =BT3 (Part No. 500 60511) ➁+➂ =BT3.1 1) (Part No. 501 05585) ➀+➁+➂ =BT3B (Part No. 501 05546) 1) Packaging unit: PU = 10 pcs.
PRK 3B Retro-reflective photoelectric sensors with polarisation filter Order guide Selection table Equipment # Switching output Switching function Order code " 2 x Push-pull switching output!!!! 1 x Push-pull switching output!!!! 1 x PNP output!! 1 PNP light switching and NPN dark switching output!!!!!! 1 PNP dark switching and NPN light switching output!!!!!! 1 x PNP light switching output! 1 x PNP dark switching output! 1 warning output! Connection M8 connector, metal, 3-pin!! M8 connector, metal, 4-pin!!! cable 2000mm! cable 200mm with M8 connector, 3-pin!! cable 200mm with M8 connector, 4-pin! cable 200mm with M12 connector, 4-pin! pin 2: not assigned, for connection to coupling modules! Indicators green : ready!!!!!!!!!! yellow : switching output!!!!!!!!!! PRK 3B/66 Part No. 501 04693 PRK 3B/66-S8 Part No. 501 04694 PRK 3B/66, 200-S8 Part No. 501 04695 PRK 3B/66, 200-S12 Part No. 501 04696 PRK 3B/4D-S8 on request IPRK 3B/4-S8 on request PRK 3B/6-S8.3 on request PRK 3B/6, 200-S8.3 on request PRK 3B/6D-S8.3 on request PRK 3B/6D, 200-S8.3 on request Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 PRK 3B/4, /4D - 01 www.leuze.de PRK 3B/6, /6D, /66-01 12
PRK 3B PRK 3B/4, /4D - 01 0605 PRK 3B/6, /6D, /66-01 13
Specifications and description Leuze electronic PRK 3B Economy Retro-reflective photoelectric sensors with polarisation filter Dimensioned drawing 1 khz 0.02 6m 10-30 V DC A 2 LS! Polarised retro-reflective photoelectric sensor with visible red light! High performance reserve! Small and compact construction with robust plastic housing, protection class IP 67/ IP 69K for industrial application! Fast alignment through brightvision! A²LS - Active Ambient Light Suppression! Push-pull switching output! High switching frequency for detection of fast events! Low current consumption A B Indicator diode yellow Optical axis U L US C LISTED Electrical connection We reserve the right to make changes 3B_b02e.fm IEC 60947... IEC 60947... Accessories: IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! Cable with M8 or M12 connector (K-D )! Reflectors! Reflective tapes Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 14 PRK 3B/6.7-01 PRK 3B/6D.7-01
PRK 3B Economy Specifications Optical data Typ. op. range limit (TK(S) 100x100) 1) 0.02 6m Operating range 2) see tables Light source 3) (modulated light) Wavelength 620nm (visible red light, polarised) Timing Switching frequency 1000Hz Response time 0.5ms Delay before start-up 300ms Electrical data Operating voltage U 4) B 10 30VDC (incl. residual ripple) Residual ripple 15% of U B Bias current 10mA Switching output 5) /6.7 1 push-pull switching output pin 4: PNP light switching, NPN dark switching pin 2: not connected 6) /6D.7 1 push-pull switching output pin 4: PNP dark switching, NPN light switching pin 2: not connected 6) Function characteristics light/dark switching Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Sensitivity fixed setting Indicators yellow light path free yellow flashing light path free, no performance reserve Mechanical data Housing plastic (PC-ABS) Optics cover plastic (PMMA) Weight (plug/cable) 10g/50g Connection type cable 2m (cross section 4x0.21mm²), M8 plastic connector Environmental data Ambient temp. (operation/storage) -30 C +55 C/-30 C +70 C Protective circuit 7) 2, 3 VDE safety class 8) II Protection class IP 67, IP 69K class 1 (acc. to EN 60825-1) Standards applied IEC 60947-5-2 Certifications UL 508 4) 1) Typ. operating range limit: max. attainable range without performance reserve 2) Operating range: recommended range with performance reserve 3) Average life expectancy 100'000h at an ambient temperature of 25 C 4) For UL applications: for use in class 2 circuits according to NEC only 5) The push-pull switching outputs must not be connected in parallel 6) Pin 2: unassigned, hence especially suitable for the connection to AS-interface I/O coupling modules 7) 2=polarity reversal protection, 3=short-circuit protection for all transistor outputs 8) Rating voltage 50V Order guide Selection table Equipment # Switching output Switching function Order code " PRK 3B/6.7 Part No. 501 04697 PRK 3B/6.7-S8 Part No. 501 04698 PRK 3B/6D.7 on request 1 x Push-pull switching output!!!! PRK 3B/6D.7-S8 on request 1 PNP light switching and NPN dark switching output!! 1 PNP dark switching and NPN light switching output!! Connection M8 connector, plastic, 4-pin!! cable 2000mm!! pin 2: not assigned, for connection to coupling modules!!!! Indicators yellow : switching output!!!! Tables Reflectors Operating range 1 TK(S) 100x100 0.02 5.0m 2 TK 40x60 0.02 3.0m 3 TK 20x40 0.02 1.5m 4 Tape 4 50x50 0.02 1.2m 1 0.02 5 6 2 0.02 3 3.6 3 0.02 1.5 2 4 0.02 1.2 1.6 Operating range [m] Typ. operating range limit [m] TK TKS = adhesive = screw type Diagrams Misalignment y [mm] Performance reserve -100-150 0 1 2 3 4 5 6 Distance x [m] A B C D 150 100 50 0-50 65 60 55 50 45 40 35 30 25 20 15 10 5 0 x Typ. response behaviour y2 y1 TK 100x100 TKS 40x60 TKS 20x40 Tape 4: 50x50 y2 y1 Typ. performance reserve A B C D 0 1 2 3 4 5 6 Remarks Distance x [m] Mounting system: ➀ ➁ ➂ ➀ =BT3 (Part No. 500 60511) ➁+➂ =BT3.1 1) (Part No. 501 05585) ➀+➁+➂ =BT3B (Part No. 501 05546) PRK 3B/6.7-01 0605 PRK 3B/6D.7-01 15 1) Packaging unit: PU = 10 pcs.
Specifications and description Leuze electronic PRK 3B Retro-reflective photoelectric sensors with polarisation filter Dimensioned drawing 1 khz 0 5m 10-30 V DC A 2 LS! Polarised retro-reflective photoelectric sensor with visible red light! Small and compact construction with robust plastic housing, protection class IP 67/ IP 69K for industrial application! A²LS - Active Ambient Light Suppression! Push-pull output with light/dark switching via teach-in button! High switching frequency for detection of fast events! Autocollimation principle! Easy setting via lockable teach button or teach input A B C D E Indicator diode green Indicator diode yellow Optical axis Teach button Attachment sleeve U L US C LISTED Electrical connection We reserve the right to make changes 3B_b03e.fm IEC 60947... IEC 60947... Accessories: IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! Cable with M8 or M12 connector (K-D )! Reflectors! Reflective tapes Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 16 PRK 3B/6.22-01 PRK 3B/4.28-01
PRK 3B Specifications Optical data Typ. op. range limit (TK(S) 100x100) 1) 0 5m Operating range 2) see tables Light source 3) (modulated light) Wavelength 620nm (visible red light, polarised) Timing Switching frequency 1000Hz Response time 0.5ms Delay before start-up 300ms Electrical data Operating voltage U 4) B 10 30VDC (incl. residual ripple) Residual ripple 15% of U B Bias current 18mA Switching output 5) /6.22 1 push-pull switching output pin 4: PNP light switching, NPN dark switching pin 2: teach input /6.22 -S8.3 1 push-pull switching output pin 4: PNP light switching, NPN dark switching /4.28 1 PNP switching output, light switching, pin 2: activation input Function characteristics light/dark reversible Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Sensitivity setting via teach-in Indicators green ready yellow light path free yellow flashing light path free, no performance reserve 6) Mechanical data Housing plastic (PC-ABS); 1 attachment sleeve, nickel-plated steel Optics cover plastic (PMMA) Weight with connector: 10g with 200mm cable and connector: 20g with 2m cable: 50g Connection type cable 2m (cross section 4x0.21mm²), connector M8 metal, cable 0.2m with connector M8 or M12 Environmental data Ambient temp. (operation/storage) -30 C +55 C/-30 C +70 C Protective circuit 7) 2, 3 VDE safety class 8) II for cable, III for metal plug Protection class IP 67, IP 69K class 1 (acc. to EN 60825-1) Standards applied IEC 60947-5-2 Certifications UL 508 4) Options Teach-in input/activation input Transmitter active/not active 8V/ 2V Activation/disable delay 1ms Input resistance 30kΩ 1) Typ. operating range limit: max. attainable range without performance reserve 2) Operating range: recommended range with performance reserve 3) Average life expectancy 100'000h at an ambient temperature of 25 C 4) For UL applications: for use in class 2 circuits according to NEC only 5) The push-pull switching outputs must not be connected in parallel 6) Display "no performance reserve" as yellow flashing is only available in standard teach setting 7) 2=polarity reversal protection, 3=short-circuit protection for all transistor outputs 8) Rating voltage 50V Tables Reflectors Operating range 1 TK(S) 100x100 0 4.0m 2 TK 40x60 0 3.0m 3 TK 20x40 0 1.3m 4 Tape 4 50x50 0 0.7m 1 0 4 5 2 0 3 3.6 3 0 1.3 1.5 4 0 0.7 1.0 Operating range [m] Typ. operating range limit [m] TK TKS = adhesive = screw type Diagrams Misalignment y [mm] Performance reserve Typ. response behaviour 40 30 y2 20 10 0-10 -20 y1-30 -40 0 1 2 3 4 5 6 Distance x [m] 50 45 40 35 30 25 20 15 10 5 0 A B C D x y2 y1 Typ. performance reserve 0 1 2 3 4 5 6 TK 100x100 TKS 40x60 TKS 20x40 Tape 4: 50x50 Remarks Distance x [m] Mounting system: ➀ ➁ ➂ A B C D PRK 3B/6.22-01 0605 PRK 3B/4.28-01 17 ➀ =BT3 (Part No. 500 60511) ➁+➂ =BT3.1 1) (Part No. 501 05585) ➀+➁+➂ =BT3B (Part No. 501 05546) 1) Packaging unit: PU = 10 pcs.
PRK 3B Retro-reflective photoelectric sensors with polarisation filter Order guide Selection table Equipment # Order code " Switching output 1 x Push-pull switching output!!!!!! 1 x PNP output! Switching function light/dark switching configurable!!!!!! light switching! Connection M8 connector, metal, 3-pin! M8 connector, metal, 4-pin!! cable 2000mm! cable 200mm with M8 connector, 3-pin! cable 200mm with M8 connector, 4-pin! cable 200mm with M12 connector, 4-pin! Configuration teach-in via button (lockable) and teach input!!!! teach-in via button!!! Options activation input! Indicators green: ready + teach sequence!!!!!!! yellow : switching output!!!!!!! PRK 3B/6.22 Part No. 501 04699 PRK 3B/6.22-S8 Part No. 501 04700 PRK 3B/6.22, 200-S8 Part No. 501 04701 PRK 3B/6.22, 200-S12 on request PRK 3B/6.22-S8.3 on request IPRK 3B/6.22, 200-S8.3 on request PRK 3B/4.28-S8 on request Sensor adjustment (teach) via teach button! The sensor is factory-adjusted for maximum operating range. Recommendation: teach only if the desired objects are not reliably detected.! Prior to teaching: Clear the light path to the reflector! The device setting is stored in a fail-safe way. A reconfiguration following voltage interruption or switch-off is thus not required. Standard teaching for average sensor sensitivity! Press teach button until both s flash simultaneously.! Release teach button.! Ready. After the standard teaching, the sensor switches when half of the light beam is covered by the object. 2 7s green simultaneously flashing at 3Hz yellow Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 PRK 3B/6.22-01 www.leuze.de PRK 3B/4.28-01 18
PRK 3B Teaching for increased sensor sensitivity! Press teach button until both s flash alternatingly.! Release teach button.! Ready. After the teaching for increased sensor sensitivity, the sensor switches when about 18% of the light beam are covered by the object. 7 12s green alternatingly flashing at 3Hz yellow Teaching for maximum operating range (factory setting at delivery)! Prior to teaching: Cover the light path to the reflector!! Procedure as for standard teaching. green yellow 2 7s simultaneously flashing at 3Hz Adjusting the switching behaviour of the switching output light/dark switching! Press teach button until the green flashes. The yellow displays the current setting of the switching output: ON = output switches on light OFF = output switches on dark! Continue to press the teach button in order to change the switching behaviour.! Release teach button.! Ready. >12s green flashes at 3Hz yellow ON = light switching OFF = dark switching PRK 3B/6.22-01 0605 PRK 3B/4.28-01 19
PRK 3B Retro-reflective photoelectric sensors with polarisation filter Locking the teach button via the teach input A static high signal ( 4ms) at the teach input locks the teach button on the device if required, such that no manual operation is possible (e.g., protection from erroneous operation or manipulation). If the teach input is not connected or if there is a static low signal, the button is unlocked and can be operated freely. Sensor adjustment (teach) via teach input The following description applies to PNP switching logic! U Teach low 2V U Teach high (U B -2V) Prior to teaching: Clear the light path to the reflector! The device setting is stored in a fail-safe way. A reconfiguration following voltage interruption or switch-off is thus not required. Standard teaching for average sensor sensitivity U Teach high U Teach low After the delay before start-up ( 300ms) has elapsed, the teach button on the device can be operated. The teach button is disabled after the 1st edge. t Teach1 4... 1000 ms Standard teach: t Teach1 = 4 1000ms After about 4ms, the current teach value is applied, teach process completed. The button remains disabled until the next signal change. Teach button may now be operated again. t green simultaneously flashing at 3Hz yellow Quick standard teach U Teach high U Teach low 4 ms 4 ms 4 ms t shortest teaching duration for standard teaching: approx. 12ms After the standard teaching, the sensor switches when half of the light beam is covered by the object. Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 PRK 3B/6.22-01 www.leuze.de PRK 3B/4.28-01 20
PRK 3B Teaching for increased sensor sensitivity U Teach high U Teach low After the delay before start-up ( 300ms) has elapsed, the teach button on the device can be operated. The teach button is disabled after the 1st edge. t Teach2 1000... 2000 ms Teach for increased sensor sensitivity: t Teach2 = 1000 2000ms After about 4ms, the current teach value is applied, teach process completed. The button remains disabled until the next signal change. Teach button may now be operated again. t green alternatingly flashing at 3Hz yellow After the teaching for increased sensor sensitivity, the sensor switches when about 18% of the light beam are covered by the object. Adjusting the switching behaviour of the switching output light/dark switching U Teach high U Teach low U Teach high U Teach low t Teach Output 2000... 3000 ms t Teach Output 2000... 3000 ms t p light 4... 1000 ms t p dark 1000... 2000 ms t t green flashes at 3Hz yellow ON = light switching OFF = dark switching After the delay before start-up ( 300ms) has elapsed, the teach button on the device can be operated. The teach button is disabled after the 1st edge. Setting the switching behaviour of the switching output: t Teach Output = 2000 3000ms Switching output switches on light: t p light = 4 1000ms Switching output switches on dark: t p dark = 1000 2000ms The button remains disabled until the next signal change. PRK 3B/6.22-01 0605 PRK 3B/4.28-01 21
Specifications and description Leuze electronic RKR 3B Retro-reflective photoelectric sensor Dimensioned drawing 1 khz 0 1.8m 10-30 V DC! Retro-reflective photoelectric sensor with visible red laser light and autocollimation principle! Small and compact construction with robust plastic housing, protection class IP 67/ IP 69K for industrial application! Low current consumption! Push-pull output with light/dark switching via teach-in button! High switching frequency for detection of fast events! Specifically for transparent media (glass, PET, foils)! Easy setting via lockable teach button or teach input! May also be used with glass reflectors (TG) A B C D E Indicator diode green Indicator diode yellow Optical axis Teach button Attachment sleeve We reserve the right to make changes 3B_b04e.fm IEC 60947... IEC 60947... Accessories: U L US C LISTED IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! Cable with M8 or M12 connector (K-D )! Reflectors! Reflective tapes Electrical connection Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 22 RKR 3B/6.42-01 RKR 3B/4.48-01
RKR 3B Specifications Optical data Typ. op. range limit (TK(S) 100x100) 1) Operating range 2) Light source 3) Wavelength Timing Switching frequency Response time Delay before start-up Electrical data Operating voltage U 4) B Residual ripple Bias current Switching output 5) /6.42 Function characteristics Signal voltage high/low Output current Sensitivity Indicators green yellow Mechanical data Housing Optics cover Weight Connection type /6.42 -S8.3 Environmental data Ambient temp. (operation/storage) Protective circuit 6) VDE safety class 7) /4.48 0 1.8m see tables (modulated light) 620nm (visible red light) 1000Hz 0.5ms 300ms 10 30VDC (incl. residual ripple) 15% of U B 15mA 1 push-pull switching output pin 4: PNP light switching, NPN dark switching pin 2: teach input 1 push-pull switching output pin 4: PNP light switching, NPN dark switching 1 PNP switching output, light switching pin 2: activation input light/dark reversible (U B -2V)/ 2V max. 100mA setting via teach-in ready light path free plastic (PC-ABS), 1 attachment sleeve, nickel-plated steel plastic (PMMA) with connector: 10g with 200mm cable and connector: 20g with 2m cable: 50g cable 2m (cross section 4x0.20mm²), connector M8 metal, cable 2m with connector M8 or M12-30 C +55 C/-30 C +70 C 2, 3 II for cable, III for metal plug IP 67, IP 69K Protection class class 1 (acc. to EN 60825-1) Standards applied IEC 60947-5-2 Certifications UL 508 4) Options Teach-in input/activation input Transmitter active/not active Activation/disable delay Input resistance 8V/ 2V 1ms 30kΩ 1) Typ. operating range limit: max. attainable range without performance reserve 2) Operating range: recommended range with performance reserve 3) Average life expectancy 100'000h at an ambient temperature of 25 C 4) For UL applications: for use in class 2 circuits according to NEC only 5) The push-pull switching outputs must not be connected in parallel 6) 2=polarity reversal protection, 3=short-circuit protection for all transistor outputs 7) Rating voltage 50V Tables Reflectors Operating range 1 TK(S) 100x100 0 1.5m 2 TK 40x60 0 1.0m 3 MTKS 50x50 0 1.0m 4 TK 20x40 0 0.5m 1 0 1.5 1.8 2 0 1 1.2 3 0 1 1.2 4 0 0.5 0.6 Operating range [m] Typ. operating range limit [m] TK = adhesive TKS = screw type MTKS = micro triple, screw type Diagrams Misalignment y [mm] Typ. response behaviour 30 20 y2 10 0-10 y1-20 -30 0 0,5 1 1,5 2 Distance x [m] x y2 y1 Remarks Mounting system: ➀ ➁ ➂ RKR 3B/6.42-01 0605 RKR 3B/4.48-01 23 ➀ =BT3 (Part No. 500 60511) ➁+➂ =BT3.1 1) (Part No. 501 05585) ➀+➁+➂ =BT3B (Part No. 501 05546) 1) Packaging unit: PU = 10 pcs.
RKR 3B Retro-reflective photoelectric sensor Order guide Selection table Equipment # Order code " Switching output 1 x Push-pull switching output!!!!!! 1 x PNP output! Switching function light/dark switching configurable!!!!!! light switching! Connection M8 connector, metal, 3-pin! M8 connector, metal, 4-pin!! cable 2000mm! cable 200mm with M8 connector, 3-pin! cable 200mm with M8 connector, 4-pin! cable 200mm with M12 connector, 4-pin! Configuration teach-in via button (lockable) and teach input!!!! teach-in via button (lockable)!!! Options activation input! Indicators green : ready!!!!!!! yellow : switching output!!!!!!! RKR 3B/6.42 Part No. 501 04702 RKR 3B/6.42-S8 Part No. 501 04703 RKR 3B/6.42, 200-S8 Part No. S501 04704 RKR 3B/6.42, 200-S12 on request RKR 3B/6.42-S8.3 on request RKR 3B/6.42, 200-S8.3 on request RKR 3B/4.48-S8 on request General information! The sensor is factory-adjusted for the detection of coloured glass. Recommendation: teach only if the desired objects are not reliably detected.! The light spot may not exceed the reflector.! Preferably use MTKS 50x50 reflectors.! For reflecting objects, the sensor has to be mounted approx. 5 angular towards the object. Sensor adjustment (teach) via teach button! Prior to teaching: Clear the light path to the reflector! The device setting is stored in a fail-safe way. A reconfiguration following voltage interruption or switch-off is thus not required. 5 Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 RKR 3B/6.42-01 www.leuze.de RKR 3B/4.48-01 24
RKR 3B Standard teaching for average sensor sensitivity (coloured glass)! Press teach button until both s flash simultaneously.! Release teach button.! Ready. If the receive signal from the reflector is too weak, the sensor indicates the error status by means of fast and simultaneous flashing of the green and yellow s. Please check the alignment, operating range, and soiling and carry out another teaching. 2 7s green simultaneously flashing at 3Hz yellow Teaching for increased sensor sensitivity (clear glass, PET, foils)! Press teach button until both s flash alternatingly.! Release teach button.! Ready. If the receive signal from the reflector is too weak, the sensor indicates the error status by means of fast and simultaneous flashing of the green and yellow s. Please check the alignment, operating range, and soiling and carry out another teaching. 7 12s green alternatingly flashing at 3Hz yellow Adjusting the switching behaviour of the switching output light/dark switching! Press teach button until the green flashes. The yellow displays the current setting of the switching output: ON = output switches on light OFF = output switches on dark! Continue to press the teach button in order to change the switching behaviour.! Release teach button.! Ready. >12s green flashes at 3Hz yellow ON = light switching OFF = dark switching RKR 3B/6.42-01 0605 RKR 3B/4.48-01 25
RKR 3B Retro-reflective photoelectric sensor Locking the teach button via the teach input A static high signal ( 4ms) at the teach input locks the teach button on the device if required, such that no manual operation is possible (e.g., protection from erroneous operation or manipulation). If the teach input is not connected or if there is a static low signal, the button is unlocked and can be operated freely. Sensor adjustment (teach) via teach input The following description applies to PNP switching logic! U Teach low 2V U Teach high (U B -2V) Prior to teaching: Clear the light path to the reflector! The device setting is stored in a fail-safe way. A reconfiguration following voltage interruption or switch-off is thus not required. Standard teaching for average sensor sensitivity (coloured glass) U Teach high U Teach low After the delay before start-up ( 300ms) has elapsed, the teach button on the device can be operated. The teach button is disabled after the 1st edge. t Teach1 4... 1000 ms Standard teach: t Teach1 = 4 1000ms After about 4ms, the current teach value is applied, teach process completed. The button remains disabled until the next signal change. Teach button may now be operated again. t green simultaneously flashing at 3Hz yellow Quick standard teach U Teach high U Teach low 4 ms 4 ms 4 ms t shortest teaching duration for standard teaching: approx. 12ms If the receive signal from the reflector is too weak, the sensor indicates the error status by means of fast and simultaneous flashing of the green and yellow s. Please check the alignment, operating range, and soiling and carry out another teaching. Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 RKR 3B/6.42-01 www.leuze.de RKR 3B/4.48-01 26
RKR 3B Teaching for increased sensor sensitivity (clear glass, PET, foils) U Teach high U Teach low After the delay before start-up ( 300ms) has elapsed, the teach button on the device can be operated. The teach button is disabled after the 1st edge. t Teach2 1000... 2000 ms Teach for increased sensor sensitivity: t Teach2 = 1000 2000ms After about 4ms, the current teach value is applied, teach process completed. The button remains disabled until the next signal change. Teach button may now be operated again. t green alternatingly flashing at 3Hz yellow If the receive signal from the reflector is too weak, the sensor indicates the error status by means of fast and simultaneous flashing of the green and yellow s. Please check the alignment, operating range, and soiling and carry out another teaching. Adjusting the switching behaviour of the switching output light/dark switching U Teach high U Teach low U Teach high U Teach low t Teach Output 2000... 3000 ms t Teach Output 2000... 3000 ms t p light 4... 1000 ms t p dark 1000... 2000 ms t t green flashes at 3Hz yellow ON = light switching OFF = dark switching After the delay before start-up ( 300ms) has elapsed, the teach button on the device can be operated. The teach button is disabled after the 1st edge. Setting the switching behaviour of the switching output: t Teach Output = 2000 3000ms Switching output switches on light: t p light = 4 1000ms Switching output switches on dark: t p dark = 1000 2000ms The button remains disabled until the next signal change. RKR 3B/6.42-01 0605 RKR 3B/4.48-01 27
Specifications and description Leuze electronic PRKL 3B Laser retro-reflective photoelectric sensor with polarisation filter Dimensioned drawing 2 khz 0 3m 10-30 V DC! Polarised retro-reflective photoelectric sensor with autocollimation principle! Small and compact construction with robust plastic housing, protection class IP 67/ IP 69K for industrial application! Push-pull output with light/dark switching via teach-in button! High switching frequency for detection of fast events and small parts! Easy setting via lockable teach button or teach input! Laser safety class 1 A B C D E Indicator diode green Indicator diode yellow Optical axis Teach button Attachment sleeve U L US C LISTED Electrical connection We reserve the right to make changes 3B_b05e.fm IEC 60947... IEC 60947... Accessories: IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! Cable with M8 or M12 connector (K-D )! Reflectors! Reflective tapes Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 28 PRKL 3B/6.22-01 PRKL 3B/4.28-01
PRKL 3B Specifications Optical data Typ. op. range limit (MTKS 50 x 50) 1) 0 3m Operating range 2) see tables Light beam characteristic collimated Light spot diameter approx. 2mm at light beam gate Light source 3) Laser (pulsed) Wavelength 655nm (visible red light, polarised) Max. output power 0.25mW Pulse duration 3µs Timing Switching frequency 2000Hz Response time 0.25ms Delay before start-up 300ms Electrical data Operating voltage U 4) B 10 30VDC (incl. residual ripple) Residual ripple 15% of U B Bias current 15mA Switching output 5) /6.22 1 push-pull switching output pin 4: PNP light switching, NPN dark switching pin 2: teach input /6.22 -S8.3 1 push-pull switching output pin 4: PNP light switching, NPN dark switching /4.28 1 PNP switching output, light switching, pin 2: activation input Function characteristics light/dark reversible Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Sensitivity setting via teach-in Indicators green ready yellow light path free yellow flashing light path free, no performance reserve 6) Mechanical data Housing plastic (PC-ABS); 1 attachment sleeve, nickel-plated steel Optics cover plastic (PMMA) Weight with connector: 10g with 200mm cable and connector: 20g with 2m cable: 50g Connection type cable 2m (cross section 3x0.20mm²), connector M8 metal, cable 2m with connector M8 or M12 Environmental data Ambient temp. (operation/storage) -10 C +40 C/-30 C +70 C Protective circuit 7) 2, 3 VDE safety class 8) II for cable, III for metal plug Protection class IP 67, IP 69K Laser class 1 (acc. to EN 60825-1) Standards applied IEC 60947-5-2 Certifications CDRH 21 CFR 1040 9), UL 508 4) Options Teach-in input/activation input Transmitter active/not active 8V/ 2V Activation/disable delay 1ms Input resistance 30kΩ 1) Typ. operating range limit: max. attainable range without performance reserve 2) Operating range: recommended range with performance reserve 3) Average life expectancy 50'000h at an ambient temperature of 25 C 4) For UL applications: for use in class 2 circuits according to NEC only 5) The push-pull switching outputs must not be connected in parallel 6) Display "no performance reserve" as yellow flashing is only available in standard teach setting 7) 2=polarity reversal protection, 3=short-circuit protection for all transistor outputs 8) Rating voltage 50V 9) Applied for Tables Reflectors Operating range 1 MTKS 50x50 0 2.0m 2 MTKS 15x30 0 1.6m 3 MTKS 20x40.1 0 1.0m 1 0 2.0 3.0 2 0 1.6 2.2 3 0 1.0 1.5 Operating range [m] Typ. operating range limit [m] MTKS = micro triple, screw type Diagrams Remarks Mounting system: ➀ ➁ ➂ PRKL 3B/6.22-01 0605 PRKL 3B/4.28-01 29 ➀ =BT3 (Part No. 500 60511) ➁+➂ =BT3.1 1) (Part No. 501 05585) ➀+➁+➂ =BT3B (Part No. 501 05546) 1) Packaging unit: PU = 10 pcs.
PRKL 3B Laser retro-reflective photoelectric sensor with polarisation filter Order guide Selection table Equipment # Order code " Switching output 1 x Push-pull switching output!!!!!! 1 x PNP output! Switching function light/dark switching configurable!!!!!! light switching! Connection M8 connector, metal, 3-pin! M8 connector, metal, 4-pin!! cable 2000mm! cable 200mm with M8 connector, 3-pin! cable 200mm with M8 connector, 4-pin! cable 200mm with M12 connector, 4-pin! Configuration teach-in via button (lockable) and teach input!!!! teach-in via button (lockable)!!! Options activation input! Indicators green : ready!!!!!!! yellow : switching output!!!!!!! PRKL 3B/6.22 Part No. 501 04705 PRKL 3B/6.22-S8 Part No. 501 04706 PRKL 3B/6.22, 200-S8 Part No. 501 04707 PRKL 3B/6.22, 200-S12 on request PRKL 3B/6.22-S8.3 on request PRKL 3B/6.22, 200-S8.3 on request PRKL 3B/4.28-S8 on request General information! The laser retro-reflective photoelectric sensors PRKL 3B/ have an optimised light beam propagation in the typical range of application of 0 1m (not to be confused with the operating range, which is 0 3m in combination with a reflector MTKS 50x50). This permits the reliable recognition of the smallest of parts or the positioning of objects with maximum precision across the entire area.! The sensor is constructed on the basis of the autocollimation principle, i.e., light being transmitted and light being received propagate along the same light axis. This permits the photoelectric sensor to be installed directly behind small holes or diaphragms. The smallest permissible diaphragm diameter for secure functioning is 3mm. Diaphragm diameter 3mm Typ. application range 0 1m! The achievable resolution depends significantly on the unit's configuration. Depending on the teach mode, the following values are possible: Setting Detection from object size 1) Sensor switches at a light occlusion of max. operating range (factory setting) 1.5mm 50% normal sensor sensitivity (standard teaching) 1mm 25% maximum sensor sensitivity (dynamic teaching) 0.1 0.2mm 5% 1) All specifications are typical values and may vary by a small amount for each unit.! For safety reasons, the laser transmitter is equipped with a monitor, which automatically switches off the transmitter in case of a component defect. In case of failure, the yellow flashes rapidly and the green is off. The state is irreversible and the sensor must be exchanged. Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 PRKL 3B/6.22-01 www.leuze.de PRKL 3B/4.28-01 30
PRKL 3B Sensor adjustment (teach) via teach button! Prior to teaching: Clear the light path to the reflector! The device setting is stored in a fail-safe way. A reconfiguration following voltage interruption or switch-off is thus not required. Standard teaching for average sensor sensitivity! Press teach button until both s flash simultaneously.! Release teach button.! Ready. After standard teaching, the sensor switches for objects with a minimum size of 1mm (see table under "General Information"). If both s flash rapidly after the teaching event, a teaching error has happened. Please check the alignment of the light beam onto the reflector and carry out another teaching event. 2 7s green simultaneously flashing at 3Hz yellow Teaching for maximal sensor sensitivity (dynamic teaching)! Press teach button until both s flash alternatingly. Sensor remains in teaching mode even after the teach button has been released.! Move some objects through the light path or swing a single object slowly back and forth through the light path.! Briefly press the teach button to terminate the teaching event.! Ready After teaching for maximum sensor sensitivity, the sensor switches for objects with a minimum size of 0.1 0.2mm (see table under "General Information"). If both s flash rapidly after the teaching event, a teaching error has happened. Please check the alignment of the light beam onto the reflector and carry out another teaching event. 7 12s green alternatingly flashing at 3Hz yellow PRKL 3B/6.22-01 0605 PRKL 3B/4.28-01 31
PRKL 3B Laser retro-reflective photoelectric sensor with polarisation filter Teaching for maximum operating range (factory setting at delivery)! Prior to teaching: Cover the light path to the reflector!! Procedure as for standard teaching. green yellow 2 7s simultaneously flashing at 3Hz Adjusting the switching behaviour of the switching output light/dark switching! Press teach button until the green flashes. The yellow displays the current setting of the switching output: ON = output switches on light OFF = output switches on dark! Continue to press the teach button in order to change the switching behaviour.! Release teach button.! Ready. >12s green flashes at 3Hz yellow ON = light switching OFF = dark switching Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 PRKL 3B/6.22-01 www.leuze.de PRKL 3B/4.28-01 32
PRKL 3B Locking the teach button via the teach input A static high signal ( 4ms) at the teach input locks the teach button on the device if required, such that no manual operation is possible (e.g., protection from erroneous operation or manipulation). If the teach input is not connected or if there is a static low signal, the button is unlocked and can be operated freely. Sensor adjustment (teach) via teach input The following description applies to PNP switching logic! U Teach low 2V U Teach high (U B -2V) Prior to teaching: Clear the light path to the reflector! The device setting is stored in a fail-safe way. A reconfiguration following voltage interruption or switch-off is thus not required. Standard teaching for average sensor sensitivity U Teach high U Teach low After the delay before start-up ( 300ms) has elapsed, the teach button on the device can be operated. The teach button is disabled after the 1st edge. t Teach1 4... 1000 ms Standard teach: t Teach1 = 4 1000ms After about 4ms, the current teach value is applied, teach process completed. The button remains disabled until the next signal change. Teach button may now be operated again. t green simultaneously flashing at 3Hz yellow Quick standard teach U Teach high U Teach low 4 ms 4 ms 4 ms t shortest teaching duration for standard teaching: approx. 12ms After standard teaching, the sensor switches for objects with a minimum size of 1mm (see table under "General Information"). PRKL 3B/6.22-01 0605 PRKL 3B/4.28-01 33
PRKL 3B Laser retro-reflective photoelectric sensor with polarisation filter Teaching for maximal sensor sensitivity (dynamic teaching) U Teach high U Teach low After the delay before start-up ( 300ms) has elapsed, the teach button on the device can be operated. The teach button is disabled after the 1st edge. t Teach2 1000... 2000 ms Teach for maximum sensor sensitivity: t Teach2 = 1000 2000ms Both s flash alternatingly, sensor remains in teaching mode.move some objects through the light path or move a single object slowly back and forth through the light path. After about 4ms, the current teach value is applied, teach process completed. The button remains disabled until the next signal change. Teach button may now be operated again. t green alternatingly flashing at 3Hz yellow After teaching for maximum sensor sensitivity, the sensor switches for objects with a minimum size of 0.1 0.2mm (see table under "General Information"). Adjusting the switching behaviour of the switching output light/dark switching U Teach high U Teach low U Teach high U Teach low t Teach Output 2000... 3000 ms t Teach Output 2000... 3000 ms t p light 4... 1000 ms t p dark 1000... 2000 ms t t green flashes at 3Hz yellow ON = light switching OFF = dark switching After the delay before start-up ( 300ms) has elapsed, the teach button on the device can be operated. The teach button is disabled after the 1st edge. Setting the switching behaviour of the switching output: t Teach Output = 2000 3000ms Switching output switches on light: t p light = 4 1000ms Switching output switches on dark: t p dark = 1000 2000ms The button remains disabled until the next signal change. Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 PRKL 3B/6.22-01 www.leuze.de PRKL 3B/4.28-01 34
PRKL 3B PRKL 3B/6.22-01 0605 PRKL 3B/4.28-01 35
RTR 3 Energetic diffuse reflection light scanner Dimensioned drawing 5 500mm 10-30 V DC! Energetic scanner with sensitivity adjustment! Visible red light for fast and easy alignment! Small construction with robust plastic housing, protection class IP 67/IP 69K for industrial application! High switching frequency for detection of fast events! Complementary switching outputs for light/ dark switching or as a control function U L US C LISTED A Receiver B Transmitter C Optical axis D Adjustment screw E Indicator diode Electrical connection We reserve the right to make changes 3_c01e.fm IEC 60947... IEC 60947... Accessories: IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! M8 connectors (D M8A )! Ready-made cables (K-D ) Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 36 RTR 3/44-300 - 04 RTR 3/44-300-S8-04
RTR 3 Specifications Optical data Typ. scanning range limit 1) 5 500mm Scanning range 2) see tables Adjustment range 60 500mm Light source (modulated light) Wavelength 660nm (visible red light) Timing Switching frequency 1000Hz Response time 0.5ms Delay before start-up 100ms Electrical data Operating voltage U B 10 30VDC (incl. residual ripple) Residual ripple 15% of U B Bias current 25mA Switching output 2 transistor outputs, complementary Function characteristics light/dark switching Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Sensitivity adjustable with multiturn potentiometer Indicators yellow reflection yellow flashing reflection, no performance reserve Mechanical data Housing plastic Optics cover plastic (PMMA) Weight 20g Connection type M8 connector (4-pin) or PUR cable 2m (cross section 4x0.2mm²) Environmental data Ambient temp. (operation/storage) -25 C +55 C/-40 C +70 C Protective circuit 3) 2, 3 VDE safety class 4) II, all-insulated Protection class IP 67, IP 69K 5) class 1 (acc. to EN 60825-1) Standards applied IEC 60947-5-2 1) Typ. scanning range limit: max. attainable range without performance reserve 2) Scanning range: recommended range with performance reserve 3) 2=polarity reversal protection, 3=short-circuit protection for all outputs 4) Rating voltage 250VAC 5) IP 69K test acc. to DIN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Order guide Designation Part No. With cable With complementary PNP switching outputs RTR 3/44-300 500 30921 With M8 connector With complementary PNP switching outputs RTR 3/44-300-S8 500 30920 With complementary NPN switching outputs RTR 3/22-300-S8 500 33310 Tables 1 5 300 500 2 8 145 220 3 10 110 120 1 white 90% 2 grey 18% 3 black 6% Scanning range [mm] Typ. scanning range limit [mm] Diagrams Misalignment y [mm] Red. of scan range y [mm] Typ. response behaviour (white 90%) 40 30 20 10 0-10 -20-30 -40 0 50 100 150 200 250 300 350 Distance x [mm] 250 200 150 100 50 x A B C A white 90% B grey 18% C black 6% y2 y1 0 0 50 100 150 200 250 300 350 400 Scanning range x [mm] y1 y2 Typ. black/white behaviour x y Remarks! With the set scanning range, a tolerance of the upper scanning range limit is possible depending on the reflection properties of the material surface. RTR 3/44-300 - 04 0605 RTR 3/44-300-S8-04 37
HRTR 3 Diffuse reflection light scanner with background suppression Dimensioned drawing 7 180mm 10-30 V DC! Scanner with adjustable background suppression! Very good black/white performance, exact adjustment via multiturn potentiometer! Small construction with robust plastic housing, protection class IP 67/IP 69K for industrial application! High switching frequency for detection of fast events U L US C LISTED A Receiver B Transmitter C Optical axis D Adjustment screw E Indicator diode Electrical connection We reserve the right to make changes 3_d02e.fm IEC 60947... IEC 60947... Accessories: IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! M8 connectors (D M8A )! Ready-made cables (K-D ) Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 38 HRTR 3/44/22-150 - 04 HRTR 3/44/22-150-S8-04
HRTR 3 Specifications Optical data Typ. scanning range limit 1) 7 180mm Scanning range 2) see tables Adjustment range 25 180mm Light beam characteristic focussed at 110mm Light source (modulated light) Wavelength 660nm (visible red light) Timing Switching frequency 1000Hz Response time 0.5ms Delay before start-up 100ms Electrical data Operating voltage U B 10 30VDC (incl. residual ripple) Residual ripple 15% of U B Bias current 25mA Switching output 2 transistor outputs, complementary Function characteristics light/dark switching Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Indicators yellow reflection Mechanical data Housing plastic Optics cover plastic (PMMA) Weight 20g Connection type M8 connector (4-pin) or PUR cable 2m/5m (cross section 4x0.2mm²) Environmental data Ambient temp. (operation/storage) -25 C +55 C/-40 C +70 C Protective circuit 3) 2, 3 VDE safety class 4) II, all-insulated Protection class IP 67, IP 69K 5) class 1 (acc. to EN 60825-1) Standards applied IEC 60947-5-2 1) Typ. scanning range limit: max. attainable range without performance reserve 2) Scanning range: recommended range with performance reserve 3) 2=polarity reversal protection, 3=short-circuit protection for all outputs 4) Rating voltage 250VAC 5) IP 69K test acc. to DIN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Order guide Selection table Order code " Equipment # Switching output PNP transistor!!!! NPN transistor!! light/dark switching!!!!!! Connection M8 connector!!! cable 5000mm! cable 2000mm!! Scanning range preset to 65mm! HRTR 3/44-150 Part No. 500 30925 HRTR 3/44-150-S8 Part No. 500 30924 HRTR 3/44-150, 5000 Part No. 500 37144 HRTR 3/22-150 Part No. 500 32368 HRTR 3/22-150-S8 Part No. 500 82277 HRTR 3/44-65-S8 Part No. 500 39581 Tables 1 7 150 180 2 10 148 175 3 15 144 169 1 white 90% 2 grey 18% 3 black 6% Scanning range [mm] Typ. scanning range limit [mm] Diagrams Misalignment y [mm] Typ. response behaviour (white 90%) 5 4 3 y2 2 1 0-1 -2 y1-3 -4-5 0 20 40 60 80 100 120 140 160 Distance x [mm] x y2 y1 Typ. black/white behaviour 12 A 10 B 8 C 6 4 2 0-2 0 20 40 60 80 100 120 140 160 180 Scanning range x [mm] A white 90% B grey 18% C black 6% Red. of scan range y [mm] x y Remarks! With the set scanning range, a tolerance of the upper scanning range limit is possible depending on the reflection properties of the material surface. HRTR 3/44/22-150 - 04 0605 HRTR 3/44/22-150-S8-04 39
HRTR 3 Diffuse reflection light scanner with background suppression Dimensioned drawing 7 180mm 10-30 V DC! Scanner with adjustable background suppression! Very good black/white performance, exact adjustment via multiturn potentiometer! Small construction with robust plastic housing, protection class IP 67/IP 69K for industrial application! High switching frequency for detection of fast events U L US C LISTED A Receiver B Transmitter C Optical axis D Adjustment screw E Indicator diode Electrical connection We reserve the right to make changes 3_d01e.fm IEC 60947... IEC 60947... Accessories: IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! M8 connectors (D M8A )! Ready-made cables (K-D ) Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 40 HRTR 3/4-150, 200-S8-03
HRTR 3 Specifications Optical data Typ. scanning range limit 1) 7 180mm Scanning range 2) see tables Adjustment range 25 180mm Light beam characteristic focussed at 110mm Light source (modulated light) Wavelength 660nm (visible red light) Timing Switching frequency 1000Hz Response time 0.5ms Delay before start-up 100ms Electrical data Operating voltage U B 10 30VDC (incl. residual ripple) Residual ripple 15% of U B Bias current 25mA Switching output 1 PNP transistor output Function characteristics light switching Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Indicators yellow reflection Mechanical data Housing plastic Optics cover plastic (PMMA) Weight 20g Connection type M8 connector (3-pin) with 200mm cable tail Environmental data Ambient temp. (operation/storage) -25 C +55 C/-40 C +70 C Protective circuit 3) 2, 3 VDE safety class 4) II, all-insulated Protection class IP 67, IP 69K 5) class 1 (acc. to EN 60825-1) Standards applied acc. to IEC 60947-5-2 1) Typ. scanning range limit: max. attainable range without performance reserve 2) Scanning range: recommended range with performance reserve 3) 2=polarity reversal protection, 3=short-circuit protection for all outputs 4) Rating voltage 150VAC 5) IP 69K test acc. to DIN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Order guide Designation Part No. With 200mm cable and M8 connector HRTR 3/4-150, 200-S8 500 33214 Tables 1 7 150 180 2 10 148 175 3 12 144 169 1 white 90% 2 grey 18% 3 black 6% Scanning range [mm] Typ. scanning range limit [mm] Diagrams Misalignment y [mm] Typ. response behaviour (white 90%) 5 4 3 y2 2 1 0-1 -2 y1-3 -4-5 0 20 40 60 80 100 120 140 160 Distance x [mm] x y2 y1 Typ. black/white behaviour 12 A 10 B 8 C 6 4 2 0-2 0 20 40 60 80 100 120 140 160 180 Scanning range x [mm] A white 90% B grey 18% C black 6% Red. of scan range y [mm] x y Remarks! With the set scanning range, a tolerance of the upper scanning range limit is possible depending on the reflection properties of the material surface. HRTR 3/4-150, 200-S8-03 0605 41
HRTR 3 Diffuse reflection light scanner with background suppression Dimensioned drawing 7 180mm 10-30 V DC! Scanner with adjustable background suppression! Very good black/white performance, exact adjustment via multiturn potentiometer! Small construction with robust plastic housing, protection class IP 67/IP 69K for industrial application! High switching frequency for detection of fast events! Cable tail with M12 connector for optimal mounting We reserve the right to make changes 3_d04e.fm IEC 60947... IEC 60947... Accessories: U L US C LISTED IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! M12 connectors (D M8A )! Ready-made cables (K-D ) A Receiver B Transmitter C Optical axis D Adjustment screw E Indicator diode Electrical connection Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 42 HRTR 3/44-150, 150-S12-03
HRTR 3 Specifications Optical data Typ. scanning range limit 1) 7 180mm Scanning range 2) see tables Adjustment range 25 180mm Light beam characteristic focussed at 110mm Light source (modulated light) Wavelength 660nm (visible red light) Timing Switching frequency 1000Hz Response time 0.5ms Delay before start-up 100ms Electrical data Operating voltage U B 10 30VDC (incl. residual ripple) Residual ripple 15% of U B Bias current 25mA Switching output 2 PNP transistor outputs, complementary Function characteristics light/dark switching Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Indicators yellow reflection Mechanical data Housing plastic Optics cover plastic (PMMA) Weight 20g Connection type M12 connector (4-pin) with 150mm cable tail (cross section 4x0.2mm²) Environmental data Ambient temp. (operation/storage) -25 C +55 C/-40 C +70 C Protective circuit 3) 2, 3 VDE safety class 4) II, all-insulated Protection class IP 67, IP 69K 5) class 1 (acc. to EN 60825-1) Standards applied IEC 60947-5-2 1) Typ. scanning range limit: max. attainable range without performance reserve 2) Scanning range: recommended range with performance reserve 3) 2=polarity reversal protection, 3=short-circuit protection for all outputs 4) Rating voltage 250VAC 5) IP 69K test acc. to DIN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Order guide Designation Part No. With complementary PNP switching outputs HRTR 3/44-150, 150-S12 500 37786 Tables 1 7 150 180 2 10 148 175 3 15 144 169 1 white 90% 2 grey 18% 3 black 6% Scanning range [mm] Typ. scanning range limit [mm] Diagrams Misalignment y [mm] Typ. response behaviour (white 90%) 5 4 3 y2 2 1 0-1 -2 y1-3 -4-5 0 20 40 60 80 100 120 140 160 Distance x [mm] x y2 y1 Typ. black/white behaviour 12 A 10 B 8 C 6 4 2 0-2 0 20 40 60 80 100 120 140 160 180 Scanning range x [mm] A white 90% B grey 18% C black 6% Red. of scan range y [mm] x y Remarks! With the set scanning range, a tolerance of the upper scanning range limit is possible depending on the reflection properties of the material surface. HRTR 3/44-150, 150-S12-03 0605 43
HRTR 3 Diffuse reflection light scanner with background suppression Dimensioned drawing 5 150mm 10-30 V DC! Scanner with special light spot and adjustable background suppression for the detection of: - objects with large holes - foils and bottles - blister - objects with varying position! Gaps of up to 10mm are not detected! Very good black/white performance, exact adjustment via multiturn potentiometer A B C D E F Receiver Transmitter Optical axis Adjustment screw Indicator diode Light spot 3x40mm at scanning range of 50mm U L US C LISTED Electrical connection We reserve the right to make changes 3_d05e.fm IEC 60947... IEC 60947... Accessories: IP 69K IP 67 (available separately see page 46)! Mounting systems (BT 3 )! M8 connectors (D M8A )! Ready-made cables (K-D ) Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 44 HRTR 3/44-50 (150)-S8-04
Special light spot HRTR 3 Specifications Optical data Typ. scanning range limit 1) 5 150mm Scanning range 2) see tables Adjustment range 25 100mm Light spot approx. 3x40mm at 50mm Light source (modulated light) Wavelength 660nm (visible red light) Timing Switching frequency 500Hz Response time 0.5ms Delay before start-up 100ms Electrical data Operating voltage U B 10 30VDC (incl. residual ripple) Residual ripple 15% of U B Bias current 25mA Switching output 2 transistor outputs, complementary Function characteristics light/dark switching Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Indicators yellow reflection Mechanical data Housing plastic Optics cover plastic (PMMA) Weight 20 g Connection type M8 connector (4-pin) M12 connector (4-pin) with 150mm cable tail (cross section 4x0.2mm²) Environmental data Ambient temp. (operation/storage) -25 C +55 C/-40 C +70 C Protective circuit 3) 2, 3 VDE safety class 4) II, all-insulated Protection class IP 67, IP 69K 5) class 1 (acc. to EN 60825-1) Standards applied IEC 60947-5-2 1) Typ. scanning range limit: max. attainable range without performance reserve 2) Scanning range: recommended range with performance reserve 3) 2=polarity reversal protection, 3=short-circuit protection for all outputs 4) Rating voltage 250VAC 5) IP 69K test acc. to DIN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Tables 1 5 50 150 2 7 48 120 3 10 44 95 1 white 90% 2 grey 18% 3 black 6% Scanning range [mm] Typ. scanning range limit [mm] Diagrams Setting to white, 150mm Misalignment y [mm] Typ. response behaviour (white 90%) 35 25 y2 15 5-5 -15 y1-25 -35 0 20 40 60 80 100 120 140 160 Distance x [mm] Setting to white, 50mm Misalignment y [mm] Typ. response behaviour (white 90%) 35 25 y2 15 5-5 -15 y1-25 -35 0 20 40 60 80 100 120 140 160 Distance x [mm] y2 y1 x Order guide Designation Part No. UL With M8 connector HRTR 3/44-50-S8 500 39724! With M12 cable tail HRTR 3/44-50,150-S12 501 02716 Remarks! With the set scanning range, a tolerance of the upper scanning range limit is possible depending on the reflection properties of the material surface. HRTR 3/44-50 (150)-S8-04 0605 45
Accessories Leuze electronic 3 Series Accessories Reflectors Dimensioned drawings! Reflectors and reflective tapes are ideally suited for Leuze retro-reflective photoelectric sensors. The performance data refer to the use of Leuze reflectors and reflective tapes. The range of retro-reflective photoelectric sensors depends on the type and size of the reflector.! Adhesive and screw type versions permit universal installation.! Precise optical alignment is not required, as the reflector may be slightly inclined relative to the optical axis.! For retro-reflective photoelectric sensors with polarisation filters, only triad-type reflectors made of plastic or reflective tape No. 4 may be used. Reflective tape No.4 Order codes: We reserve the right to make changes 3_zu_e.fm Designation Part No. TKS 100x100 500 22816 TK 100x100 500 03192 TKS 40x60 500 40820 TKS 20x40 500 81283 MTKS 50x50 500 36188 MTKS 20x40.1 501 04130 MTKS 20x30 500 40894 Reflective tape no. 4, roll 50x1000 500 38060 Reflective tape no. 4, roll 50x22800 500 38062 Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 46 3 Series Accessories - 04
Accessories 3 Series Dimensioned drawings M8 D M8A-3P-SK D M8A-4P-SK Connectors, cables K-D M8W- K-D M8A- Dimensioned drawings M12 KD 095-4 KD 095-4A For devices with M8/M12 connectors, there are connectors with ready-made cable and connectors with screw connection available. Protection class IP 67 (DIN 40050) is provided with both the connector cable accessories and the field-wireable connectors. Important: With throughbeam photoelectric sensors, a connector is required both for the transmitter and the receiver. K-D M12W-4P- K-D M12W-4P- -DP- K-D M12A-4P- K-D M12A-4P- -DP- 3 Series Accessories - 04 0605 47
3 Series Accessories Connectors, cables Selection table M8/M12 connector, user-configurable Connection type Insulation displacement connection Insulation displacement connection Screw terminals KD 095-4 Part No. 500 31324 M8, without cable, 3-pin M8, without cable, 4-pin M12, without cable, 4-pin D M8A-3P-SK Part No. 501 04582 D M8A-4P-SK Part No. 501 04583 KD 095-4A Part No. 500 31323 M8 connection cable with connector, single-sided Length 2m 5m Length 2m 5m 10m Length 2m 5m 10m K-D M8W-3P-2m-PVC Part No. 501 04521 K-D M8W-3P-5m-PVC Part No. 501 04523 K-D M8W-4P-2m-PVC Part No. 501 04525 K-D M8W-4P-5m-PVC Part No. 501 04527 K-D M8W-4P-10m-PVC Part No. 501 04529 K-D M8W-4P-2m-PUR Part No. 501 04531 K-D M8W-4P-5m-PUR Part No. 501 04761 K-D M8W-4P-10m-PUR Part No. 501 04534 PVC cable sheath, 3-pin PVC cable sheath, 4-pin PUR cable sheath, 4-pin K-D M8A-3P-2m-PVC Part No. 501 04520 K-D M8A-3P-5m-PVC Part No. 501 04522 K-D M8A-4P-2m-PVC Part No. 501 04524 K-D M8A-4P-5m-PVC Part No. 501 04526 K-D M8A-4P-10m-PVC Part No. 501 04528 K-D M8A-4P-2m-PUR Part No. 501 04530 K-D M8A-4P-5m-PUR Part No. 501 04532 K-D M8A-4P-10m-PUR Part No. 501 04533 We reserve the right to make changes 3_zu_e.fm Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 48 3 Series Accessories - 04
Accessories 3 Series Selection table Connectors, cables M12 connection cable with connector, single-sided Length 2m 5m 10m K-D M12W-4P-2m-PVC Part No. 501 04543 K-D M12W-4P-5m-PVC Part No. 501 04545 K-D M12W-4P-10m-PVC Part No. 501 04547 20m Length 2m 5m 10m K-D M12W-4P-2m-PUR Part No. 501 04562 K-D M12W-4P-5m-PUR Part No. 501 04564 K-D M12W-4P-10m-PUR Part No. 501 04566 PVC cable sheath, 4-pin K-D M12A-4P-2m-PVC Part No. 501 04542 K-D M12A-4P-5m-PVC Part No. 501 04544 K-D M12A-4P-10m-PVC Part No. 501 04546 K-D M12A-4P-20m-PVC Part No. 501 04753 PUR cable sheath, 4-pin K-D M12A-4P-2m-PUR Part No. 501 04561 K-D M12A-4P-5m-PUR Part No. 501 04563 K-D M12A-4P-10m-PUR Part No. 501 04565 M8 / M12 connection cable with connector, single-sided, with 2 integrated s in transparent connector Remarks circuit diagram (K-D M12 -DP- ): Length 2m 5m Length 2m 5m 10m K-D M8W-4P-2m-DP-PUR Part No. 501 04535 M8, PUR cable sheath, 4-pin K-D M8W-4P-5m-DP-PUR Part No. 501 04536 M12, PUR cable sheath, 4-pin K-D M12W-4P-2m-DP-PUR Part No. 501 04549 K-D M12W-4P-5m-DP-PUR Part No. 501 04551 K-D M12W-4P-10m-DP-PUR Part No. 501 04553 K-D M12A-4P-2m-DP-PUR Part No. 501 04548 K-D M12A-4P-5m-DP-PUR Part No. 501 04550 K-D M12A-4P-10m-DP-PUR Part No. 501 04552 3 Series Accessories - 04 0605 49
3 Series Accessories Mounting systems Dimensioned drawings BT 3 ➀ ➁ ➂ ➀ = BT 3 (Part No. 500 60511) ➁+➂ = BT 3.1 1) (Part No. 501 05585) ➀+➁+➂ = BT 3B (Part No. 501 05546) We reserve the right to make changes 3_zu_e.fm 1) Packaging unit: PU = 10 pcs. Leuze electronic GmbH + Co. KG Post-box 1111 D-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 50 3 Series Accessories - 04
P.O. Box 11 - n/teck 021/ 57 Fax +49(0) 7021/ 573-199 A qualified partner in the field of......detection Standard sensors in cubic design Contrast, colour, luminescence scanners Cylindrical sensors Fibre optic amplifiers Measuring sensors Double sheet monitoring/splice detection Forked photoelectric sensors Accessories...identification Bar code readers Bar code positioning systems Data matrix code readers Optical data transmission systems Hand-held readers Laser distance measuring devices RF identification systems Industrial machine vision...protection Safety light curtains Safety relays and interfaces Multiple light beam safety devices Sensor accessories and signal devices Safety laser scanners Measuring light curtains Safety interlocks Service for all aspects of machine safety For quick, simple sales and service information go to......www.leuze.de GB 209/00 05/06 Part No. 501 05 719