velocity standard 01 V-S-01 Chic and robust - a highly-structural portable 10 x10 exhibit that emphasizes your identity and message seamlessly with a combinaton of fabric graphics, rigid accents and accessories. features and benefits: - Custom appearance - Easy to assemble - Combination of rigid and fabric graphics - Aluminum construction: vertical extrusions 50mm x 100mm dimensions: Hardware Assembled unit: 113.2 (w) x 94.5 (h) x 49.5 (d) approx. 2875.3mm(w) x 2400mm(h) x 1257.3mm(d) Table: 21.2 (w) x 40.5 (h) x 19.7 (d) approx. 538.5mm(w) x 1029mm(h) x 500.4 mm(d) Shipping Shipping dimensions - ships in 2 cases Each WMC12x6 case: 52 (l) x 30 (w) x 15 (h) 1320.8mm(l) x 762mm(w) x 381mm(h) - Installation tool included - Kit includes one frame, two v-leg tables, two wings, two fabric graphic panels, four 50 watt spotlights, one literature holder, one monitor bracket, and two WMC12x6 molded cases - Lifetime hardware warranty against manufacturer defects Graphic Panel A: Total visible area: 79.25 w x 94.5 h 2025.65mm(w) x 2400.3mm(h) Panel B: Total visible area: 33.25 w x 94.5 h 844.55mm(w) x 2400.3mm(h) Wings: Total visible area: 21.325 w x 11.5 h 541.7mm(w) x 292.1mm(h) Refer to related graphic template for more information Approximate shipping weight (entire kit): 177 lbs / 80.3 kg additional information: Graphic materials: Dye-sublimated fabric & UV prints on 6mm sintra Table holds max weight 25 lbs / 11.3 kg Monitor mount max weight: 25 lbs / 11.3 kg Lights included: LV1 50 watt, low voltage spotlight, curved arm, silver finish, 19.5 from end to end Tabletop colors: silver black mahogany natural velocity 2013 Nimlok Display and Exhibit Solutions Worldwide For questions contact your local Nimlok distributor
Parts included Part Label Qty Part code x6 PM4S3-1200-A-A 10'-0" [3048mm] VE-13 x3 PH2C-1 VE-17 x2 PH-300-S-S x4 PH-4RN-S-S VE-19 x2 PH-21R-S-S x4 PH-160-S-S x6 PH-1200-L1 VL-02 x2 V-LG-02 V-WS-CT-01 x2 V-WS-CT-01 Connector x3 IB2 10'-0" [3048mm] Panel A x1 - Panel B x1 - Wing x2 - Standoff x4 CKSO Monitor mount x1 OR-OPT1-B Light x4 LV1-CLP- Lit holder x1 LN-112 Tool kit x1 V-TK-01 Step stool x1 STEP STOOL Steamer x1 FABRIC STEAMER-ES 1.
Step 1. Connect two s using attachment detail below to create an upright. Create three uprights. Connect completed uprights with s as shown in attachment detail below. Add s to the outer uprights 12 from the bottom/top of frame. Take care to turn locks only half a turn. Step 2. Slide VE-13 internal connector into the lower s. Slide upper s over VE-13 internal connectors as detailed below. Attach completed uprights to s using attachment detail below. VE-13 VE-13 2 VERTICALS PH AND 1 HORIZONTAL W/ IB2 TOP IB POST W/ STOP EXTRUSION WITH S Tension Glides TOP IB2 Lock Detail IB2 BACK VIE BOTTO T HANDLE IB C STOP STOP BOTTOM T HANDLE EXTRUSION ITH S Slide the two IB2s together and then tighten the screws to lock the IB2s together HORIZONTAL AND VERTICAL EXTRUSION BY USING T- HANDLE TOOL HORIZONTAL EXTRUSION BY USING T- HANDLE TOOL 2.
Step 3. Apply panel A to display. Start with upper left corner and stretch graphic across display. PANEL A GRAPHIC A ON BACKSIDE Step 4. Slide VE-13 internal connector into lower. Slide upper over VE-13 internal connector. Push rubber gaskets in top and bottom of panel B into the channels of the VE-19s. Lock VE-19s with graphic attached to frame on the left and completed upright on the right. Take care not to damage graphic. VE-19 GRAPHIC PANEL B VE-13 VE-19 POST W/ STOP TOP CHANNEL BOTTOM CHANNEL EXTRUSION WITH S Tension Glides TOP T HANDLE BOTTOM PULL TABS EXTRUSION ITH S C STOP STOP Fabric graphic is installed by pressing into TOP and BOTTOM channel. To pull the graphic out of the channels, use TABS on the back side. PULL TABS Fabric graphic is installed by pressing t into TOP and BOTTOM channel. To pull the graphic out of the channels, use TABS on the back side. HORIZONTAL EXTRUSION BY USING T- HANDLE TOOL 3.
Step 5. To attach the lit holder, slide the joining bar down the middle channel of designated upright. Hold at desired height and tighten. Attach lit rack to joining bar with screw using attachment detail below. To attach monitor mount, slide square head bolts on back of mount down middle channel of designated upright to desired height and tighten using attachment detail below. Step 6. Attach standoffs to the middle channel of designated uprights where shown. Attach the wings using detail below. WING WING MONITOR V-M-BRACKET-01 MOUNT LIT HOLDER LN112 Monitor Mount Detail LIT. HOLDER JOINER BAR THUMBSCREW SQUARE BOLT W/ WING NUT Top DETAIL Graphic Channel of extrusion NT Toggle TOP HALF UPRIGHT LITERATURE HOLDER Slide JOINER BAR into channel.place literature rack. Then, gently tighten. WASHER SCREW LEFT OR RIGHT CHANNEL Slide the square bolts into the channel. Once the monitor mount is at the desired postion turn the wing nuts clockwise to secure the monitor mount to the extrusion. Barrel Screw the NT toggle into the base of the barrel and then insert the NT toggle into the channel of the extrusion and twist to tighten into place. Next, place the top of the through the hole in the graphic and then screw on the STANFOFF top to secure the graphic in place. 4.
Step 7. Attach VE-17 to back side of table leg as seen in locking detail below. Attach VE-17 with leg to designated upright. Attach V-WS-CT-01 tabletop to table legs using connector detail below. Step 8. Slide two lights onto clips and place in channel on s as shown in detail below. Slide two lights onto clamps and place over VE-19 as shown in detail below. VE-17 VE-17 V-WS-CT-01 V-WS-CT-01 VL-02 LV1 Light VL-02 W/ CLIP W/ CLAMP EXTRUSION TO LEG LEG Light clip 5mm Hex key Tool CLAMP Place LEG and lock horizontal extrusions by using 5mm hex key tool. Insert the thumb connector into the bottom of the counter top and make a 1/4 turn clockwise to tighten in place. 1- Slide light clip onto the. 2-Then slide the into the channel at an angle and then gently lower down. 1- Slide light clip onto the. 2-Then slide the into the channel at an angle and then gently lower down. 5.
check out these related products: velocity standard 01 velocity standard 05 velocity standard 02 velocity standard 06 velocity standard 03 velocity standard 07 Redesign of this exhibit without approval by Nimlok may result in dangerous and unsafe structures. Nimlok disclaims any responsibility for redesigned exhibits it does not approve in writing. Parts and components such as panels and extrusions are manufactured to metric sizing. We continue to improve and modify our product range and reserve the right to vary the specifications without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE. See Graphic Templates for graphic bleed specifications. velocity standard 04 velocity standard 08