RAILINGSYSTEMS PLANNING MANUAL EFFICIENCY DECIDES

RAILINGSYSTEMS PLANNING MANUAL EFFICIENCY DECIDES

THE SYSTEM The system that can even be without any load-bearing handrail... * With general technical approval (AbP) and certified type structural properties! * Requirement for this: LSG-ESG 2x10 mm, Protection of the glass edge using an edge protector 2 www.glassline.de

THE SYSTEM TYPE STATIC from LSG-TSG 2x6 mm The full glass railing system with certified type structural properties In public and private construction projects The System Panel widths of up to 6,000 mm can be achieved In buildings and outdoors Panel heights of up to 1,400 mm can be achieved In flat areas and on stairs No glass type structural properties are required! No additional glass type structural properties are needed for a variety of different applications! 6.000 mm 1.400 mm Applications Measurement tables can be found starting on page 32. 6.000 mm Safety from the Outset AbP General technical approval (AbP) No more incalculable time and cost factors for inspections or building code conditions. BALARDO ALU reduces the project period to a minimum and can be used straight away without any red tape. Handrails TYPE STATIC Type structural properties Benefit from maximum safety thanks to certified type structural properties for a variety of different applications in private and public areas as well as in buildings and outdoors. Certified by the LGA (Landesgewerbeanstalt Bayern) The type-certified BALARDO ALU system is structurally calculated and the dynamic structural behaviour for continuous use is tested by means of an extensive series of tests. There is no need for single-case permission (ZIE) This means no time-consuming bureaucratic procedures - BALARDO ALU can be put to direct use. Service www.glassline.de 3

THE SYSTEM Impressive Transparency with a handrail or glass edge protector profile edge protection in the application Overview System-specific glass edge protector profile U-profile Round handrail, 42.4 mm Round handrail, 48.3 mm Height 6.0 mm 30 x 27 mm, d = 3.0 mm ø 42.4 mm, d = 1.5 mm ø 48.3 mm, d = 1.5 mm For glass (LSG / ESG) 2 x 10 mm For glass (LSG / ESG) From 2 x 6 mm For glass (LSG / ESG) From 2 x 6 mm For glass (LSG / ESG) From 2 x 6 mm Technical data, see page 36. 4 www.glassline.de

THE SYSTEM The System Table of Contents Profile Overview Page 6 Click n Fix Installation Kit Page 7 System Profile Top1 Page 8 System Profile Top2 Page 10 System Profile Top3 Page 12 System Profile Side1 Page 14 System Profile Side2 Page 18 Accessories Page 22 The System Applications Applications System Application In Flat Areas Page 24 System Application On Stairs Page 26 System Application French Balcony Page 28 Service Handrails Page 30 Application and Measurement Tables Page 32 Handrail Installation Page 35 Stainless Steel Handrails Page 36 Wooden Handrails Page 37 Customised Handrail Page 38 Accessories for Stainless Steel Handrails Page 40 Installation Instructions Page 42 Enquiry Form Page 43 Handrails Service www.glassline.de 5

THE SYSTEM Profile Overview System Profiles for Floor Installation Page 8 GLAS System Profile Top1 Page 10 PROFIL System Profile Top2 Page 12 System Profile Top3 System Profiles for Lateral Installation Page 14 System Profile Side1 Page 18 System Profile Side2 6 www.glassline.de

THE SYSTEM Click n Fix Installation Kit consisting of a clamping shoe, clamp as well as an inner and outer seal Seals Inner and outer seal The System Material: EPDM Length: approx. 3,000 mm Clamp Clamping shoe Clamp Material: Length: Clamping shoe Material: Length: POM approx. 300 mm EPDM approx. 3,000 mm Applications CLICK N FIX assembly Revolutionary Fast: Click n Fix Installation The revolutionary Click n Fix installation kit makes the installation of full glass railing systems extremely easy: Insert the glass and place the clamp on the profile. As soon as you press the panel outwards, it will click and the clamp will fall into its position and lock the panel in place. Installation video www.glassline.de/balardo Handrails Press Service Ready! Insert Click www.glassline.de 7

THE SYSTEM System Profile Top1 For floor installation Profile Material: Length: inset: Aluminium 3,000 mm approx. 100 mm Surfaces: Natural Untreated Stainless steel effect (E6/EV1) Premium brushed stainless steel finish Fixing spacing 108 ø 14 7 108 Drilling pattern (ø 14 mm) Private area 1 Public area 2 a = 0 mm a = 2 mm 88 36 125 2 2 2 2 2 2 2 2 2 2 2 125 124 3000 35 108 124 35 124 35 Inner Angle Cover Plate d = 2.0 mm self-adhesive Outer Angle 124 35 Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. All of our profiles have general technical approval, certified type structural properties and are LGA-certified. 1 Capping load 0.5 kn/m 2 Capping load 1.0 kn/m 8 www.glassline.de

THE SYSTEM System Profile Top1 Sample Applications Sample Application 1 Sample Application 2 height (H) 1,400* The System height (H) 1,400* Applications Profile protrusion 0-5 bei H 1.400 0-10 bei H 1.2 Sample Application 3 Sample Application 4 height (H) 1,400* Drain grate On-site drain Gradient height (H) 1,400* Continuous backfilling or expanding mortar Handrails * Application and measurement tables, see pages 32-33. Service Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. www.glassline.de 9

THE SYSTEM System Profile Top2 For Floor Installation Profile Material: Length: inset: Aluminium 3,000 mm approx. 100 mm Surfaces: Natural Untreated Stainless steel effect (E6/EV1) Premium brushed stainless steel finish Fixing spacing 132 Drilling pattern (ø 14 mm) Private area 1 Public area 2 a = 0 mm a = 2 mm ø 14 4 132 60 60 120 125 2 2 2 2 2 2 2 2 2 2 3000 2 125 Inner Angle Cover Plate 132 d = 2.0 mm 120 120 self-adhesive Outer Angle 120 Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. All of our profiles have general technical approval, certified type structural properties and are LGA-certified. 1 Capping load 0.5 kn/m 2 Capping load 1.0 kn/m 1010 www.glassline.de

THE SYSTEM System Profile Top2 Sample Applications Sample Application 1 Sample Application 2 The System height 1,400* height 1,400* Continuous backfilling or expanding mortar Applications 37 Sample Application 3 height 1,400* Handrails * Application and measurement tables, see pages 32-33. Service Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. www.glassline.de 11

THE SYSTEM System Profile Top3 For Floor Installation Profile Material: Length: inset: Aluminium 3,000 mm approx. 100 mm Surfaces: Natural Untreated Stainless steel effect (E6/EV1) Premium brushed stainless steel finish Fixing spacing 132 Drilling pattern (ø 14 mm) Private area 1 Public area 2 a = mm a = 100 mm ø 14 132 24 24 48 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 3000 Inner Angle Cover Plate Innenecke 132 d = 2.0 mm 48 self-adhesive Outer Angle Außenecke Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. All of our profiles have general technical approval, certified type structural properties and are LGA-certified. 1 Capping load 0.5 kn/m 2 Capping load 1.0 kn/m 1212 www.glassline.de

THE SYSTEM System Profile Top3 Sample Applications Sample Application 1 Sample Application 2 The System height 1,400 * height 1,400 * Continuous backfilling or expanding mortar 37 Applications Sample Application 3 Sample Application 4 height 1,400 * height 1,400 * Continuous Handrails Steel frame * Application and measurement tables, see pages 32-33. e.g. Side view of stair stringer Service Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. www.glassline.de 13

THE SYSTEM System Profile Side1 For lateral installation Profile Material: Length: inset: Aluminium 3,000 mm approx. 100 mm Surfaces: Natural Untreated Stainless steel effect (E6/EV1) Premium brushed stainless steel finish Fixing spacing 116 ø 28 LL = 16 x 36 70 Drilling pattern (At the back, oblong hole 16 x 36 mm, at the front ø 28 mm) Private area 1 Public area 2 a = 0 mm a = 2 mm 56 116 70 125 2 2 2 2 2 2 2 2 2 2 2 125 3000 Inner Angle Cover Plate 120 d = 2.0 mm 116 with facing panel 59 self-adhesive 56 without facing panel Outer Angle Facing Panel ø 28 enecke Profile Caps * Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. All of our profiles have general technical approval, certified type structural properties and are LGA-certified. 1 Capping load 0.5 kn/m 2 Capping load 1.0 kn/m * Color silver (similar E6EV1) 1414 www.glassline.de

Ste aluminium 36 x 115 mm, continuous, see page 22 THE SYSTEM System Profile Side1 Attention! Only use dowels with a low dowel head. Sample Applications Sample Application 1 Sample Application 2 Continuous Continuous backfilling backfilling or expanding or expanding mortar mortar height 1,400* height 1,400* height 1,400* The System Applications Attention! Attention! Only use Only dowels use dowels with with a low a dowel low dowel head. head. Attention! Only use dowels with a low dowel head. Sample Application 3 Sample Application 4 height 1,400* Continuous height 1,400* Continuous Handrails Steel profile Steel profile * Application and measurement tables, see pages 32-33. Service Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. Screw connection to steel profile: e.g. M10 countersunk head with rosette, page 22. Dowelling: e.g. dowel with internal thread and pre-positioned installation www.glassline.de 15

THE SYSTEM Steel profile Steel profile Steel profile Steel profile System Profile Side1 Sample Applications Sample Application 5 Sample Application 6 height 1,400* height 1,400* Continuous Continuous height 1,400* height 1,400* Continuous Window frame height 1,400* Steel frame height 1,400* Window sill Continuous Steel frame Continuous Continuous Steel frame Steel frame Steel profile Steel profile Sample Application 7 Sample Application 8 e.g. Side view of stair stringer * Application and measurement tables, see pages 32-33. Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. Screw connection to a steel frame: e.g. M10 countersunk head with rosette, page 22. 1616 www.glassline.de

THE SYSTEM System Profile Side1 Sample Applications Sample Application 9 Sample Application 10 The System height 1,400* Continuous Drain grate On-site drain Gradient height 1,400* Steel frame Continuous Applications Steel frame e.g. Side view of stair stringer Sample Application 11 Sample Application 12 Continuous Continuous Gradient height 1,400* Steel frame height 1,400* Steel frame height 1,400* 36 Spacer 30 x 30 x 30 mm at a gap of 2 or 0 mm Screw connection to a steel frame: e.g. M10 countersunk head with rosette, page 22. Dowelling: e.g. dowel with internal thread and pre-positioned * Space fixing profile - aluminium 36 x 115 mm, continuous, see page 22 Attention! Only use dowels with a low dowel head. * Application and measurement tables, see pages 32-33. Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. Continuous backfilling or expanding mortar * Handrails Service installation www.glassline.de 17

THE SYSTEM System Profile Side2 For lateral installation Profile Material: Length: inset: Aluminium 3,000 mm approx. 100 mm Surfaces: Natural Untreated Stainless steel effect (E6/EV1) Premium brushed stainless steel finish LL = 16 x 36 Drilling pattern (Oblong hole 16 x 36 mm) Fixing spacing Private area 1 Public area 2 a = 0 mm a = 2 mm 57 Innenecke 57 125 2 2 2 2 2 2 2 2 2 2 2 125 3000 Inner Angle Cover Plate d = 2.0 mm self-adhesive Outer Angle Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. All of our profiles have general technical approval, certified type structural properties and are LGA-certified. 1 Capping load 0.5 kn/m 2 Capping load 1.0 kn/m 1818 www.glassline.de

THE SYSTEM System Profile Side2 Sample Applications Sample Application 1 Sample Application 2 The System height 1,400* height 1,400* height 1,400* Applications Sample Application 3 Sample Application 4 Continuous backfilling or expanding mortar height 1,400* Steel frame (continuous) Handrails Bearing level min. 100 mm. e.g. Side view of stair stringer Service * Application and measurement tables, see pages 32-33. Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. www.glassline.de 19

THE SYSTEM System Profile Side2 Sample Applications Sample Application 5 Sample Application 6 height 1,400 height * 1,400 * Continuous Window sill Continuous Window sill Window frame Window frame height 1,400 * height 1,400 * Continuous Continuous e.g. Side view of stair stringer e.g. Side view of stair stringer Sample Application 7 Sample Application 8 Drain grate height 1,400 * On-site On-site drain drain Continuous Continuous Drain grate Drain grate Gradient Gradient Steel frame height 1,400 * On-site drain Gradient height 1,400 * Steel frame Bearing level min. 100 mm. * Application and measurement tables, see pages 32-33. Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. 2020 www.glassline.de

THE SYSTEM System Profile Side2 Sample Applications Sample Application 9 The System height 1,400* 36 Gradient Spacer 30 x 30 x 30 mm at a gap of 2 or 0 mm Applications Space fixing profile - aluminium 36 x 115 mm, continuous, see page 22 Handrails Bearing level min. 100 mm. Service * Application and measurement tables, see pages 32-33. Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. www.glassline.de 21

THE SYSTEM Accessories Vertical Edge Protector Profile System-specific glass edge protector profile For glass: 2 x 6 mm 2 x 8 mm 2 x 10 mm Height 6 mm Material: Stainless steel 1.4301 Surface: brushed Length: 1,300 mm including adhesive fixing Space Fixing Profile - Aluminium Space fixing profile including spacers (12 pcs.) Surfaces: U 36 x 115 mm Material: Length: Aluminium 3,000 mm Natural Untreated Stainless steel effect (E6/EV1) Premium brushed stainless steel finish Rosette Rosette for M10 countersunk head screw DIN 7991 Material: Stainless steel A4 Packing unit per 12 pieces Spacer Spacer joint width: 10 mm Material: EPDM 15 mm Height: 36 mm 20 mm self-adhesive on one side Packing unit per 5 pieces for LSG 2x6, 2x8 and 2x10 mm Screw Locking Screw Locking ml bottle 2222 www.glassline.de

Applications System Applications www.glassline.de 23

Applications System Application In a Flat Area and Profile 30 width 100-6.000* 30 30 30 Profile Profile length 3.000 30 Top1 Top2 Top3 Side1 Side2 37 mm 37 mm height 1.400 * height 1.400 * height 1.400 * height 1.400 * height 1.400 * * Application and measurement tables, see pages 32-33. Profile spacing 40 mm. Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. 2424 www.glassline.de

Applications System Application In a Flat Area Corner Solution Outer corner The System Outer corner Applications Floor Wall Inner corner Floor Inner corner Flexible Installation of the Panels independent of the profile (glass joint not on the profile joint) 30 Handrails 40 40 conforms with the profile (glass joint on the profile joint) 30 40 40 Service Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. www.glassline.de 25

Applications System Application On Stairs Glas und Profil GLASS width 100-6.000* 30 Profile length 3.000 30 40 PROFILE Top1 Top2 Top3 Side1 Side2 37 mm 37 mm height 1.400 * height 1.400 * height 1.400 * height 1.400 * height 1.400 * * Application and measurement tables, see pages 32-33. Profile spacing 40 mm. Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. 2626 www.glassline.de

Applications System Application On Stairs Profile Joint The System B B B Fußboden Außenecke H B Außenecke 800 400 B 140-220 - 90 400 800 H 40 H H H - 130 B - 130 B 800 40 400 800 B 400 B H 140-220 140-220 - 90-90 400 800 400 800 40 40 H H H H - 13 Applications - 130 B B Wand B B B H Innenecke H Fußboden 90 H B 800 = mögliche Ausführung 400 140-220 90-90 400 800 H H Innenecke H H H 90-130 90-130 B 40 B = mögliche Ausführung B = possible application 90 90 H H B 40 B independent of the profile (glass joint not on the profile joint) H 30 90 90 H Handrails B 40 40 = mögliche Ausführung conforms with the profile (glass joint on the profile joint) 30 40 40 Service Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. www.glassline.de 27

Applications System Application French Balcony With a Load-bearing Handrail Connection to the Building 30 0-6.000* 30 thicknesses Private area 1 Public area 2 From 2 x 6 mm 3 From 2 x 8 mm 3 * Application and measurement tables, see pages 32-33. Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. 1 Capping load 0.5 kn/m 2 Capping load 1.0 kn/m 3 LSG made of ESG 1.52, PVB film. 2828 www.glassline.de

Applications System Application French Balcony Without a Handrail Connection to the Building The System 30 0-6.000* 30 Handrails Applications thicknesses Public area 2 From 2 x 10 mm 3 * Application and measurement tables, see pages 32-33. Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge Service protector profile on pages 22 + 36. 2 Capping load 1.0 kn/m 3 LSG made of TSG 1.52, PVB film. www.glassline.de 29

Freedom of Design for You Enjoy freedom with BALARDO ALU, even with the glass. The high transparency and variety of combinations that BALARDO ALU offers correspond with any décor, particularly in combination with the systemspecific glass edge protector profile. The filigree system is suitable for any individual glass design and harmoniously supports the effect of any motif and pattern. Whether it's printed or coloured PVB film there is no limit to your creativity. With BALARDO ALU you have certified type structural property tables for all system components. We only laminated safety glass (LSG) for maximum safety. BALARDO ALU can be implemented as a full glass railing system without any additional inspections. This opens up a wealth of unimaginable design options. Type structural properties certified by LGA Bavaria - no additional glass type structural properties are required for the wide range of applications. e.g. with a photo* e.g. with a standard pattern* e.g. with a company logo* * Film printed and laminated into the laminated safety glass. 3030 www.glassline.de

Composition / Application Composition LSG-Float 1 2 x 10 mm Das System LSG-ESG 2 Application 2 x 6 mm 2 x 8 mm 2 x 10 mm 2 4 5 Anwendungen 1 3 1 inset 2 butt joint 30 3 overlap 40 4 gaps 3 R 15 0 5 Handrail/ edge protecton Edge protection or joint 30 mm Das Glas ~ 100 mm Bottom Top R 15 No glass drilling required Handläufe Cost-effective Easy installation Insert Press Ready! 1 Laminated safety glass comprising 2 x float glass, 1.52 mm PVB film (polyvinyl butyral film). 2 Laminated safety glass comprising 2 x toughened glass, 1.52 mm PVB film (polyvinyl butyral film). 3 Can be achieved with LSG-TSG 2 x 10 mm. Service edges brushed or polished. and profile joints should be protected against penetrating moisture. dimensions, see pages 32-33 Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. www.glassline.de 31

Application and Measurement Tables Type structural properties certified by LGA Bavaria - no additional glass type structural properties are required for the wide range of applications. Private Area (Capping Load 0.5 kn/m) B H height width 40 B width H height Fixing spacing a 0 mm* With a Handrail - Only with a Edge Protector Profile In flat areas and on stairs width [mm] Max. glass height [mm] Permissible wind load (kn/m 2 ) with a glass height 900 1,000 1,100 1,1 1,2 1,300 1,400 LSG-TSG 2 x 10 100-6,000 1,400 4.75 3.85 3.10 2.80 2.40 2.20 1.80 With a Load-Distributing Handrail only in a flat area width [mm] Max. glass height [mm] Permissible wind load (kn/m 2 ) with a glass height 900 1,000 1,100 1,1 1,2 1,300 1,400 LSG Float 2 x 10 1,000-2,400 1 1,400 2.20 1.75 1.40 1.25 1.10 1.00 0.80 LSG-TSG 2 x 6 0-3,000 1 1,2 1.75 1.40 1.20 1.05 0.85 In flat areas and on stairs width [mm] Max. glass height [mm] Permissible wind load (kn/m 2 ) with a glass height 900 1,000 1,100 1,1 1,2 1,300 1,400 LSG-TSG 2 x 8 100-6,000 1,400 3.15 2. 2.00 1.80 1. 1.40 1.20 LSG-TSG 2 x 10 100-6,000 1,400 4.75 3.85 3.10 2.80 2.40 2.20 1.80 * Top3 fixing spacing a mm PVB film 1.52 mm 1 Handrail connection to a structure (load-bearing elements) required! Width ratio of the adjoining glass panels max. 1:2 or 2:1 Handrail joint: 7 mm from the glass joint with a non-rigid handrail connection 100 mm from the glass joint with a rigid handrail connection. Filler and end plates 100-0 mm must be connected on the top for load distribution purposes. Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. 3232 www.glassline.de

Application and Measurement Tables Type structural properties certified by LGA Bavaria - no additional glass type structural properties are required for the wide range of applications. Public Area (Capping Load 1.0 kn/m) The System H height B width H height 40 B width Applications Fixing spacing a 2 mm* With a Handrail - Only with a Edge Protector Profile width [mm] In flat areas and on stairs Max. glass height [mm] Permissible wind load (kn/m 2 ) with a glass height 900 1,000 1,100 1,1 1, 1,2 1,300 LSG-TSG 2 x 10 100-6,000 1,300* 4.75 3.85 3.10 2.80 2.60 2.40 2.20 With a Load-Distributing Handrail width [mm] In flat areas and on stairs Max. glass height [mm] Permissible wind load (kn/m 2 ) with a glass height 900 1,000 1,100 1,1 1,2 1,300 1,400 LSG-TSG 2 x 8 0-2,400 1 1,1 3.15 2. 2.00 1.80 LSG-TSG 2 x 10 100-6,000 1,300* 4.75 3.85 3.10 2.80 2.40 2.20 0-2,400 1 1,400* 1.80 Handrails * Top3 glass height: max. 1,2 mm / fixing spacing a 100 mm PVB film 1.52 mm 1 Handrail connection to a structure (load-bearing elements) required! Width ratio of the adjoining glass panels max. 1:2 or 2:1 Handrail joint: 7 mm from the glass joint with a non-rigid handrail connection 100 mm from the glass joint with a rigid handrail connection. Filler and end plates 100-0 mm must be connected on the top for load distribution purposes. Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36. www.glassline.de 33 Service

Notes 3434 www.glassline.de

Handrails Handrail Installation Butt Joints & Installation The System Alternative 1 Possible handrail joint 7 mm away from the glass joint with a non-rigid connection (with LSG made of TSG 2 x 6 and 2 x 8 mm) Alternative 2 Possible handrail joint 100 mm away from the glass joint with a rigid connection (with LSG made of TSG 2 x 6 and 2 x 8 mm) Handrail Installation Handrails Applications Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge Service protector profile on pages 22 + 36. The handrail butt joint can be freely selected with respect to the glass edge with LSG made of TSG 2 x 10. www.glassline.de 35

Handrails Stainless Steel Handrails System-specific glass edge protector profile For LSG 2x10 mm Material: Stainless steel 1.4301 Surface: brushed incl. adhesive fixing Length 3,000 mm U Profiles 30 3 27 Edge protection: U 30 x 27 x 3.0 mm Groove dimension: 24 x 24 mm Material: Stainless steel 1.4301 Surface: brushed 24 incl. rubber clip-in profile Length 3,000 mm Round Ø 42.4 mm Ø 42.4 1.5 24 beading tube: Ø 42.4 x 1.5 mm Groove dimension: 24 x 24 mm Material: Stainless steel 1.4301 Surface: brushed 24 incl. rubber clip-in profile Length 5,000 mm Round Ø 48.3 mm Ø 48.3 30 24 6 1.5 beading tube: Ø 48.3 x 1.5 mm Groove dimension: 27 x 30 mm Material: Stainless steel 1.4301 Surface: brushed 27 incl. rubber clip-in profile Length 5,000 mm If necessary, adhesive should be used to secure the handrail against lifting. PVB-compatibility should be taken into consideration. 3636 www.glassline.de

Handrails Wooden Handrails U Profiles 30 3 The System Edge protection: U 30 x 27 x 3.0 mm Groove dimension: 24 x 24 mm Material: Stainless steel 1.4301 Surface: brushed Round on a U-Profile Applications Wooden handrail: Ø 55 mm Groove dimension: 31 x 30 mm Material: Steamed beech Surface: polished and varnished Rectangular on a U-Profile Service 27 24 incl. rubber clip-in profile Length 3,000 mm Ø 55 30 24 for wooden add-on elements Length 3,000 mm 31 Wooden handrail: w / h / 40 mm Groove dimension: 31 x 30 mm Material: Steamed beech Surface: polished and varnished 40 Length 3,000 mm Handrails 30 31 If necessary, adhesive should be used to secure the U-profile and wooden add-on element against lifting. PVB-compatibility should be taken into consideration. www.glassline.de 37

Handrails Customised Handrail Sample Applications * Load-bearing handrail joint 21-26 Non-loading bearing customised handrail 0 Ø 52 * Load-bearing handrail joint 21-26 0 Ø 52 Non-loading bearing customised handrail * load-bearing handrail absolutely essential. 3838 www.glassline.de

Handrails Customised Handrail Curved Handrail Support Ø 42.4 The System 80 Ø 16 Point fittings: Ø 52 mm Material: Stainless steel 1.4404 Surface: lathed Straight Handrail Support Ø 52 Ø 21 Applications Point fittings: Ø 52 mm Material: Stainless steel 1.4404 Surface: lathed Stainless Steel Handrail Ø 42.4 2.0 beading tube: Ø 42.4 x 2.0 mm Material: Stainless steel 1.4301 Surface: brushed Length 3,000 mm Handrails Wooden Handrail Ø 60 Service 80 55 Ø 42.4 Ø 52 Ø 21 Ø 16 Wood: Ø 60 mm Material: Steamed beech Surface: polished and varnished Length 3,000 mm www.glassline.de 39

Handrails Accessories for Stainless Steel Handrails Accessories for Stainless Steel Handrail Ø 42.4 mm Handrail connector Material: Surface: Stainless steel 304 V2A brushed Corner connector 90 Material: Surface: Stainless steel 304 V2A brushed Handrail end caps Material: Surface: Stainless steel 304 V2A brushed Accessories for Stainless Steel Handrail Ø 48.3 mm Handrail connector Material: Surface: Stainless steel 304 V2A brushed Corner connector 90 Material: Surface: Stainless steel 304 V2A brushed Handrail end caps Material: Surface: Stainless steel 304 V2A brushed 4040 www.glassline.de

Handrails Notes Service Handrails Applications The System www.glassline.de 41

Service CLICK N FIX assembly Installation Video Installation Instructions 1 Fix the profile in place www.glassline.de/balardo 2 Insert the clamping shoe 4 3 Press the outer seal firmly 5 6 Click Insert the clamp and press the glass towards the outer seal Insert the glass 7 Insert the inner seal 4422 Press it until the clamp locks in place with an audible click 8 Install the handrail of the glass edge protector profile www.glassline.de 9 Ready!

Service Enquiry Form Name Company House Number / Street Quick Enquiry: Copy enquiry Complete Fax to +49 (0) 6291/6259-11 Your enquiry will be processed as quickly as possible. The System Town or City / Postcode Tel. Fax E-mail Construction projects Applications System Profile Top1 Top2 Top3 Side1 Side2 metres thickness Surface 2 x 6 mm 2 x 8 mm 2 x 10 mm Natural Untreated Stainless steel effect (E6/EV1) Premium brushed stainless steel finish Accessories Handrails Corners Cover plate Veneering (Side1) Spacer Inner Angle Outer Angle Facing Panel Profile Caps joint 10 15 20 piece piece piece piece Handrail edge protector profile * Height 6 mm U 30 x 27 mm Ø 42.4 mm Ø 48.3 mm Ø 55 mm /40 mm Service * for LSG 20 www.glassline.de 43

GLASSWALL Ceiling-high glazing with general technical approval (AbP) and a safety function! The highly transparent system makes full glass in a railing area more attractive and cost-effective than ever before. The innovation clamp installation principle will win you over and reduce installation and planning time. Point fixings with AbZ (general technical approval) and type structural properties for the problem-free planning and implementation of point-fixed glass constructions. For maximum transparency and safety for a variety of different applications. line GmbH. Industriestr. 7-8. 74740 Adelsheim. GERMANY Phone +49 (0) 6291 6259-0. Fax +49 (0) 6291 6259-11 @glassline.de. www.glassline.de Copyright 2012 by GLASSLINE GmbH. 2nd Edition January 2013. Subject to technical changes without prior notice