GNSS-750 ANTENNA GUIDE SITE SELECTION GUIDELINES. Additional Equipment Required. Accessories

Similar documents
GPS-701-GGL and GPS-702-GGL

GPS-703-GGG and GPS-703-GGG-N

o-ring grease can be used to hold the o-ring in the groove during installation.

o-ring grease can be used to hold the o-ring in the groove during installation.

supplied o-ring grease can be used to hold the o-ring in the groove during installation.

Poseidon Reference Manual

Model 3101, 3102 and 3103 Conical Log-Spiral Antennas

HDTV Antenna. Contemporary Indoor. User s Guide

Planishing hammer stand For use with SKU Planishing hammer

2001A. 200KHz Function Generator Instruction Manual. 99 Washington Street Melrose, MA Phone Toll Free

15 Planer Stand. Model Due to continuing improvements, actual product may differ slightly from the product described herein.

500S Smart Antenna Installation and Operation Manual. P/N Rev. A 09/17 E29808

Specifications. Important Safety Information

ITEM Pipe Thread Kit (10 Piece Set - 7 Dies) Assembly and Operating Instructions

GNSS-3P. GNSS Passive Antenna TECHNICAL PRODUCT DATA SHEET DESCRIPTION FEATURES OPTIONS

Owner s Manual & Safety Instructions

Model 3116 Double-Ridged Waveguide Horn

9 PIECE TUNGSTEN CARBIDE HOLE SAW KIT. Model 90721

Installation Procedures Maserati Gran Turismo Sport SNS 85

Advanced Test Equipment Rentals ATEC (2832)

9 QUICK RELEASE WOODWORKING VISE

Inline Antenna Signal Amplifier

Installation Procedures 2018 Mustang GT & EcoBoost SNS 135

TK 100 Probe Calibrator. Instruction Manual

30 Bending Brake. Model Assembly and Operating Instructions. Distributed exclusively by Harbor Freight Tools.

Installation Procedures Jaguar XF SNS 92

Broadband Current Probe Series Operation Manual

Installation Procedures Dodge Charger R/T Scat Pak, SRT/Hellcat. SNS 66a

Instruction Sheet D-CPU. Secure CPU Holder

AIS 300 Installation Instructions

THANK YOU FOR PURCHASING OUR STUDIO RTA CREATION STATION

USER GUIDE. WR284 Waveguide TRL Calibration Kit GHz. Models: WR284C30\32 Series (Rev A) 03/16

RADOME OMNI ANTENNA GHz, 6 dbi, FOAM FILLED

Gypsy Statement of Limited Warranty. Part 1 General Terms

Model 3110B Biconical Antenna

Instruction Sheet REB SERIES. Rotating Sliding Base REB18

Owner s Manual & Safety Instructions

Broadband Step-Up Transformer. User Manual

User s Guide ASSISTIVE LISTENING SYSTEMS

Installation Procedures Dodge Challenger SXT, R/T, Scat Pak, SRT & Hellcat SNS 1a

MaxLite LED Self-Driven LiteBars

Broadband Current Probe Series Operation Manual

Glass Electrode Meter

Model 5100F. Advanced Test Equipment Rentals ATEC (2832) OWNER S MANUAL RF POWER AMPLIFIER

MANUAL METAL SHRINKER/STRETCHER

Model 3148 & Log-Periodic Dipole Array Antenna

Type N Coaxial Calibration Kit

Single Flex and Double Flex Couplings (i)

Model Assembly & Operating Instructions

Installation Procedures For Corvette Basic/C-6 SNS 28

Installation Procedures 2015 Corvette C-7 Z06 With Carbon Fiber Kit SNS 50a

Series 500. Owner s Manual. Analog Transmitters by Data Industrial. Data Industrial. Data Industrial 2/95 PN 72806

Model 3106 Double-Ridged Waveguide Horn

14 Piece Slide Hammer and Puller Set

Radio Remote(s) (Installation Manual)

USER GUIDE 2.92mm Coaxial Calibration Kit

Field Hub Installation Guide. P/N Rev. C 05/15

SIR-WRR1. User's Guide SIRIUS Echo Antenna. Signal Repeater System Accessory

Installation Guide. Delphi XM FM Direct Accessory. For Use With Roady2 and SKYFi2 Satellite Radio Receivers

Record the serial number and date of purchase in your manual for future reference.

INSTRUCTION MANUAL. 1 Light Exterior Wall Lantern. Home Depot SKU (UPC ) Home Depot SKU (UPC ) (Prairie Bronze)

PRODUCT SAFETY SOLUTIONS MODEL HWI-01. Model HWI-01 Serial Number:

QuadroMAX. Installation Manual. QM Series. LED Outdoor Lighting Fixtures REV: 3/22/16

Current Probe Fixture Instruction Manual

Instruction Sheet. VRS Series. Vertical Rackmount system for multiple cable/satellite receivers

Bulk Current Injection Probe Test Procedure

LOW NOISE AMPLIFIER LN4000 OPERATING MANUAL THIS AMPLIFIER IS FOR RECEIVER ONLY. DO NOT USE WITH TRANSMITTER!

Comfort 10S Wall Hardwire Installation and Operations Manual

Operating Instructions and Parts Manual Folding Hydraulic Crane Model: JFHC-200X

Advanced Test Equipment Rentals ATEC (2832)

Shrinker and stretcher

Owner s Manual ODYSSEY BENCH MODEL. O4100B shown REV E. Southern Avenue, Phoenix, AZ USA Workhorseproducts.

Instruction Sheet SNE SERIES. Cable Chase

Instruction Manual Model Upconverter

Installation Procedures 2015 Roush Mustang Stage 1 & 2. SNS 62b

Signal Integrity Test Report

HUSTLER 7' & 8' POOL TABLE ASSEMBLY INSTRUCTIONS

A Solution for Every Application. Trimble GNSS Geodetic Antennas TRANSFORMING THE WAY THE WORLD WORKS

Vi6208, Vi6216, Vi6232 Vi6308, Vi6316, Vi6332

Single Arm Pole Mount. Installation Manual Edition v1.01. For models: UNI-SA/14 UNI-SA/21.5 UNI-SA/26 UNI-SA01-MAN

Log Periodic Dipole Array Antenna

Mortising Attachment

Shiba Drive USER MANUAL

Preliminary Data Sheet!

Model BiConiLog Antenna. User Manual

Tilting & Swiveling Flat Panel Wall Mount Installation Guide Model: AXS2040

Ordering Information. Stepping Relay Unit G9B. Model Number Legend

Owner s Manual. LPA500 UHF Log Periodic Antenna

CRD 410 MANUAL FITTING INSERTER

Archived 3/18/10 USER MANUAL EMCO MODEL 3141 BICONILOG TM LOG-PERIODIC / T BOW-TIE ANTENNA Rev A 01/97

Instruction Manual Model Upconverter

MWC5-98. Operation Manual. MWC /800MHz Cloning Receiver with FM Radio Option. Radio. man_mwc598_v11b

1300-lb Furniture and Crate Movers

Prime Engineering Up-Rite Stander

AJKIT-1. Syncbox Anti-jam Upgrade Kit. User Manual Version 1.1

SRS-200 Solar Radiation Sensor Installation and Setup Instructions. SRS-200 with optional Leveling Plate and Mounting Bracket. Revision 2.0.

KNEEWALL APPLICATION

Model 935A. Dual Tone Sender INSTRUCTION MANUAL

MODEL 3810/2 Line Impedance Stabilization Network

Antenna. Wilson. Wide-Band Panel Antenna Window, Ceiling, Wall & Outdoor Mounts. Appearance of device and accessories may vary.

Transcription:

GNSS-750 ANTENNA GUIDE OM-20000120 Rev 5 October 2012 The GNSS-750 is an active antenna designed to receive signals from the GPS, Galileo and GLONASS satellites as well as L-Band signals. This antenna is designed to operate for GPS L1/L2/L2C/L5, GLONASS L1/L2/L3 and L-Band frequency bands. The GNSS-750 is also designed to operate for Galileo L1/E5a/E5b and E6 frequency bands and receives Compass B1/B2/B3. This guide provides the basic information you need to install and begin using your new antenna. Additional Equipment Required The following equipment is required to set up the GNSS-750: A sturdy pillar or mount with a 5/8" x 11 thread that extends between 3/8" and 7/8" (9 mm and 22 mm) Coaxial cable with a male N connector A device with an antenna input port that both receives the RF signal and provides 3.3 to 12.0 VDC to the antenna 1 Accessories Additional available accessories include the following: A radome (NovAtel part number 01018195) SITE SELECTION GUIDELINES For optimal performance, select a site that meets the following conditions before installing: An unobstructed as possible line-of-sight from horizon to horizon and at all bearings and elevation angles. As far as possible from reflective objects, especially those that are above the antenna and any water bodies, which can be a strong source of multi-path reflections. If obstructions and reflective surfaces are within 30 m, ensure the site is as high as possible. Otherwise, mount the antenna as low as possible. 1. Most NovAtel GNSS receivers provide the necessary power through their antenna RF connectors. Check the applicable receiver user manual for details. 1

INSTALLING THE ANTENNA After a site has been selected, install the antenna as follows: 1. Verify that the thread on the mount does not extend more than 7/8" (22 mm) to ensure the antenna receptacle is not damaged when the mount is inserted. If it extends further than 7/8" (22 mm), add two jam nuts to shorten the exposed thread, ensuring the nuts are well tightened. 2. Align the mount thread with the metal adapter on the bottom of the antenna and rotate the antenna clockwise until it is securely screwed to the mount. 3. Remove the dust cap from the antenna s connector. 4. If attaching a TNC coaxial cable, attach the male TNC connector to the antenna s TNC connector. If attaching a N connector coaxial cable, remove the N to TNC adaptor and attach the male N connector of the coaxial cable to the antenna s N connector. 5. Attach the other end of the coaxial cable to the antenna input port of the receiving device, which must provide power as detailed in the, Specifications section of this guide. 2

ANTENNA CARE The GNSS-750 is designed to withstand the elements, including rain, snow, and dust. However, to ensure your antenna performs optimally, keep the top surface and the choke rings of the antenna clean and brush off any ice and snow. A radome is recommended. In addition, ensure the N connector remains clean and dry and replace the dust cap when a cable is not connected. ELEVATION GAIN PATTERNS 3

SPECIFICATIONS 3 db pass band (typical) Out-of-band rejection (typical) 0 900 900 1002.5 MHz 1002.5 1062.5 MHz 1062.5 1102.5 MHz 1370 1465 MHz 1410 1440 MHz 1668 1718.5 MHz 1718.5 1798.5 MHz 1798.5 1900 MHz 1900 3000 MHz Gain at zenith ( = 90 ) (min) Gain roll-off (zenith to horizon) LNA gain (typical) Polarization Noise figure (typical) Differential propagation delay (maximum) Nominal impedance RF Upper:1525-1612 MHz Lower:1164-1301 MHz 80 db 70 db 50 db 30 db 30 db 50 db 30 db 50 db 70 db 80 db +5 dbic 10-15 db 41 3 db Right-hand circular 1.5 db 9 ns 50 VSWR 1.5 : 1 POWER Input voltage 3.3-12 V Current (typical) 70 ma PHYSICAL Diameter 380 mm (14.96") Weight 7.6 kg (317.47 oz) Height 200 mm (7.48 ) ENVIRONMENTAL Operating temperature -55 C to +85 C (-67 F to Storage temperature -55 C to +90 C (-67 F to Salt spray MIL-STD-810F Method 509.4 Water ingress protection IPX6 and IPX7 Dust ingress protection IP6X 4

MECHANICAL DRAWINGS All dimensions are in millimetres (mm) where 1 inch = 25.4 mm. 5

PHASE CENTER Please see the, Mechanical Drawings section on the previous panel and the close up of the label below before reading this section. Model Name For absolute offset numbers and to download PCV (Phase Center offsets and Variations) tables, please visit the GEO++ Web site at www.geopp.com. When using the Web site mentioned above, look for the NovAtel listing of your antenna model and its hardware revision. Only integer hardware revisions affect the phase center offsets. For example, the numbers given for hardware revision 2.02 are applicable to an antenna labelled H/W Rev: 2.00, 2.05, 2.12 and so on. Table 1 shows typical absolute and relative offset numbers for the current 750 antenna model. Table 1: Height If you need any further advice on this matter, please visit our Web site at www.novatel.com. Other methods of contacting Customer Support can be found on the last panel of this guide. Warranty Policy NovAtel Inc. warrants that its Global Positioning System (GPS) products are free from defects in materials and workmanship, subject to the conditions set forth below, for the following periods of time: GPSAntenna Modules:One (1) Year Cables and Accessories:Ninety (90) Days Date of sale shall mean the date of the invoice to the original customer for the product. NovAtel's responsibility respecting this warranty is limited solely to product repair at an authorized NovAtel location only. Determination of repair will be made by NovAtel personnel or by technical personnel expressly authorized by NovAtel for this purpose. The foregoing warranties do not extend to (i) nonconformities, defects or errors in the products due to accident, abuse, misuse or negligent use of the products or use in other than a normal and customary manner, environmental conditions not conforming to NovAtel s specifications, or failure to follow prescribed installation, operating and maintenance procedures, 6 Absolute (GEO++) with Radome Absolute (GEO++) without Radome L1 170 mm 162 mm L2 157 mm 159 mm

(ii) defects, errors or nonconformities in the products due to modifications, alterations, additions or changes not made in accordance with NovAtel s specifications or authorized by NovAtel, (iii) normal wear and tear, (iv) damage cause by force of nature or act of any third person, (v) shipping damage; or (vi)service or repair of product by the dealer without prior written consent from NovAtel. In addition, the foregoing warranties shall not apply to products designated by NovAtel as beta site test samples, experimental, developmental, preproduction, sample, incomplete or out of specification products or to returned products if the original identification marks have been removed or altered. The warranties and remedies are exclusive and all other warranties, express or implied, written or oral, including the implied warranties of merchantability or fitness for any particular purpose are excluded. NovAtel shall not be liable for any loss, damage or expense arising directly or indirectly out of the purchase, installation, operation, use or licensing or products or services. In no event shall NovAtel be liable for special, indirect, incidental or consequential damages of any kind or nature due to any cause. There are no user-serviceable parts in the GPS Antenna and no maintenance is required. If the unit is faulty, replace with another unit and return the faulty unit to NovAtel Inc. You must obtain a RETURN MATERIAL AUTHORIZATION (RMA) number by calling NovAtel Customer Support at 1-800-NOVATEL (U.S. and Canada only) or 403-295-4500 before shipping any product to NovAtel or a dealer. Once you have obtained an RMA number, you will be advised of proper shipping procedures to return any defective product. When returning any product to NovAtel, please return the defective product in the original packaging to avoid damage. Before shipping any material to NovAtel or Dealer, please obtain a Return Material Authorization (RMA) number from the point of purchase or NovAtel s Customer Support. WEEE Notice If you purchased your GNSS-750 in Europe, please return it to your dealer or supplier at the end of its life. The objectives of the European Community's environment policy are, in particular, to preserve, protect and improve the quality of the environment, protect human health and utilise natural resources prudently and rationally. Sustainable development advocates the reduction of wasteful consumption of natural resources and the prevention of pollution. Waste electrical and electronic equipment (WEEE) is a regulated area. Where the generation of waste cannot be avoided, it should be reused or recovered for its material or energy. WEEE products may be recognized by their wheeled bin label. RoHS Statement The GNSS-750 Antenna is not within the scope of the RoHS Directive. It is intended to be used as a Reference Station antenna at a fixed location, over a long period of time, and as such it qualifies to use the Large-Scale Fixed Installation RoHS scope exemption. 7

Questions or Comments If you have any questions or comments regarding your GNSS-750, please contact NovAtel Customer Support using one of methods provided below. E-mail: support@novatel.com Web: www.novatel.com Phone: 1-800-NOVATEL (International) or 403-295-4500 (U.S. & Canada) Fax: 403-295-4501 8 Copyright 2012 NovAtel Inc. All rights reserved. Unpublished rights reserved under international copyright laws. Recyclable