GENERL NOTES 162-971 1 OF 12 THESE INSTLLTION INSTRUCTIONS RE SUPPLEMENT TO THE PPROVED SHOP DRWINGS. USE IN CONJUNCTION WITH THOSE DRWINGS. 1 - HNDLING, STORING ND PROTECTING LUMINUM MTERIL. THE FOLLOWING PRECUTIONS RE RECOMMENDED TO SSURE ERLY CCEPTNCE OF YOUR PRODUCTS ND WORKMNSHIP. - HNDLE CREFULLY - DO NOT DROP FROM THE TRUCK. STCK WITH DEQUTE SEPRTION SO MTERIL WILL NOT RU TOGETHER. STORE OFF THE GROUND. PROTECT GINST ELEMENTS ND OTHER CONSTRUCTION TRDES. - KEEP MTERIL WY FROM WTER, MUD ND SPRY - PREVENT CEMENT, PLSTER ND OTHER MTERILS FROM DMGING THE FINISH. C - PROTECT THE MTERILS FTER ERECTION, Y WRPPING WITH KRFT PPER - OR Y ERECTING VISQUEEN/CNVS SPLTTER SCREENS. CEMENT, PLSTER, TERRZZO ND OTHER LKLINE MTERILS RE VERY HRMFUL TO THE FINISH ND SHOULD E REMOVED WITH WTER ND MILD SOP EFORE SETTING OCCURS. UNDER NO CIRCUMSTNCES LLOW THESE MTERILS TO DRY OR PERMNENT STINING WILL OCCUR. 2 - GENERL RULES THE FOLLOWING PRCTICES RE RECOMMENDED FOR LL WLL INSTLLTIONS. - RED COMPLETE INSTRUCTIONS EFORE ORDERING GLSS OR FRICTING MTERIL. - CHECK SHOP DRWINGS TO ECOME THOROUGHLY FMILIR WITH THE JO. F - MKE CERTIN CONSTRUCTION WHICH WILL RECEIVE YOUR MTERILS IS CCORDING TO THE CONTRCT DOCUMENTS. IF NOT, NOTIFY THE GENERL CONTRCTOR IN WRITING ND RESOLVE DIFFERENCES EFORE PROCEEDING WITH YOUR WORK. G - INSULTE LL LUMINUM TO E PLCED DIRECTLY IN CONTCT WITH THE MSONRY OR INCOMPTILE MTERILS WITH HEVY COT OF ZINC CHROMTE OR ITUMINOUS PINT. H - FOLLOW KWNEER INSTLLTION ND GLZING INSTRUCTIONS. J - CHECK LL MTERIL ON RRIVL FOR QUNTITY. K - E SURE YOU HVE LL THE MTERILS ND TOOLS NEEDED TO EGIN THE INSTLLTION. 1 - PPROVED SHOP DRWINGS 2 - LEVEL ND PLUM (TRNSIT) 3 - FSTENERS ND REQUIRED DRIVERS. 4 - PERIMETERS ND CCESSORIES SUCH S NCHORS, FSTENERS, SLEEVES ND/OR SPLICE CPS. 5 - SELING MTERILS. 6 - GLZING MTERILS. L - FOLLOW SELNT MNUFCTURER'S RECOMMENDTIONS FOR PROPER SELNT ND PPLICTION. LL SELNTS ND MSTICS MUST E COMPTILE WITH LL SURFCES INCLUDING OTHER SELNT SURFCES. WHERE REQUIRED LL SELNTS MUST DHERE TO LL SURFCES INCLUDING OTHER SELNT SURFCES. 1600 SYSTEM NOTES 2 1600 SYSTEM IS VILLE WITH 1" FRMING MEMERS WHICH CCEPT OTH 1" ND 1/4" INFILLS. LSO 1/4" FRMING MEMERS WHICH CCEPT 1/4" INFILLS ONLY RE VILLE. THE TERM "CPTURED VERTICLS OR CPTURED HORIZONTLS" WILL E USED THROUGHOUT THESE INSTRUCTIONS. THIS MENS FRMING MEMERS THT CCEPT N EXTERIOR PRESSURE PLTE ND COVERS. "STRUCTURL GLZED VERTICLS" DO NOT CCEPT EXTERIOR METL. VERTICL MULLION SPLICE - VERTICL MULLIONS THT RE STRUCTURLLY GLZED MUST E SPLICED T HORIZONTL. LOCTION OF THIS SPLICE MUST E REVIEWED FOR STRUCTURL INTEGRITY Y FCTORY ENGINEERING. 2 GLSS ITE IS 1/2" T CPTURED VERTICLS ND HORIZONTLS. GLSS ITE IS 1" T STRUCTURL GLZED VERTICLS. GLSS SIZES MUST E CLCULTED FROM PPROVED SHOP DRWINGS. UNLESS OTHERWISE SPECIFIED, IT IS RECOMMENDED THT SILICONE SELNT E USED FOR LL INTERNL SELS. SELNT MUST E PPLIED PER THE SELNT MNUFCTURER'S RECOMMENDTIONS ND PSS LL DHESION ND COMPTIILITY TESTING. T LL JOINT SELS, SELNT MUST DHERE TO METL, S, THERML SEPRTOR ND JOINT PLUG MTERILS. CLEN LL SURFCES PRIOR TO PPLICTION OF SELNT ND PRIME WHERE NECESSRY TO CHIEVE PROPER DHESION. SHIM LL SILL HORIZONTLS T SETTING LOCK LOCTIONS. STRUCTURL SEL NOTES STRUCTURL SILICONE SEL - THE GLZING INSTLLER IS RESPONSILE FOR SELECTING ND CONTCTING THE SILICONE MNUFCTURER TO DETERMINE WHICH TYPE OF SILICONE IS TO E USED ND WHT SMPLES RE REQUIRED TO E SUMITTED FOR DHESION ND COMPTIILITY TESTING. THE SILICONE SELNT SHLL NOT E PPLIED TO KWNEER PRODUCTS WITHOUT THE PPROVL OF THE SILICONE MNUFCTURER ND UNTIL LL REQUIRED TESTING IS COMPLETED ND DETILED PPLICTION INSTRUCTIONS HVE EEN DELIVERED TO THE INSTLLER Y THE SILICONE MNUFCTURER. IF YOU FIND THE SILICONE MNUFCTURER'S INSTLLTION INSTRUCTIONS RE NOT IN CCORDNCE WITH KWNEER'S INSTLLTION INSTRUCTIONS, IT IS YOUR RESPONSIILITY TO NOTIFY KWNEER OF THIS CONFLICT PRIOR TO GLZING. YOUR GLSS SUPPLIER MUST E MDE WRE THT THEIR GLSS WILL E USED IN SSG PPLICTION. THE PPLICTION MUST E PPROVED Y THE GLSS SUPPLIER PRIOR TO GLZING. NY STRUCTURL SILICONE GLZED PRODUCT PPLICTION THT IS NOT SHOWN IN KWNEER'S STNDRD PRODUCT LITERTURE MUST E PRE-PPROVED Y KWNEER. EXTERIOR GLSS WETHER SEL - SELNT TO E TYPE S RECOMMENDED Y THE MNUFCTURER OF THE STRUCTURL SELNT EING USED FOR THIS PROJECT. SELNT MUST E PPLIED PER THE SELNT MNUFCTURER'S RECOMMENDTIONS. WETHER SEL SELNT MUST DHERE TO EXTERIOR MTERIL. C - LL MTERILS RE TO E INSTLLED PLUM, LEVEL ND TRUE. D - LL WORK SHOULD STRT FROM ESTLISHED ENCH MRKS ND COLUMN CENTER LINES ESTLISHED Y THE RCHITECTURL DRWINGS ND THE GENERL CONTRCTOR. E - THE SEQUENCE OF ERECTION SHOULD E COORDINTED WITH THE JO SUPERINTENDENT SO DELYS RE PREVENTED ND RISK OF MTERIL DMGE IS MINIMIZED. IF PRESETTING OF NCHORGE IS REQUIRED, COORDINTE WITH GENERL CONTRCTOR ND SUPERVISE LOCTION. TYPICL SPLICE LOCTION OVER HORIZONTL INSTLLTION INSTRUCTIONS 95449-87 02/17/12 DRWING: PRT NO. 162-971 1 OF 12
STEP - 4 FRME SSEMLY TTCH NCHORS TO MULLIONS WHERE PPLICLE. NCHOR PREP MY E FRICTED IN THE FIELD OR FCTORY. CONSULT PPROVED SHOP DRWINGS FOR CORRECT METHOD. STNDRD NCHOR PREP IS THRU-OLTED T INTERMEDITE VERTICLS ND TPPING PLTES RE USED T JM VERTICLS. REFER TO PPROVED SHOP DRWINGS FOR CORRECT METHOD. WHEN WELDING NCHORS, PROTECT INSTLLED GLSS ND METL FROM WELD SPLTTER. DETILS SME FOR "CPTURED VERTICLS" STRUCTURL GLZED VERTICL WELD PLTE 027-477 SEPRTOR ETWEEN NCHOR ND MULLION STEP - 4 FRME SSEMLY TTCH SHER LOCKS. 128-394 SCREWS #12 x 1 7/8" PN HED TYPE HED/SILL SHER LOCK/NCHOR WHERE PPLICLE ND SHOWN ELOW. 162-314 6" SYSTEM T JMS 162-315 7 1/2" SYSTEM T JMS 162-342 6" SYSTEM T MULLIONS 162-343 7 1/2" SYSTEM T MULLIONS STRUCTURL INTEGRITY OF NCHOR ND FSTENERS MUST E CHECKED Y FCTORY ENGINEERS. STEP - 5 INSTLL 162-310 THERML REK 162-310 THERML REK OPTION TO INSTLL THERML REK FTER VERTICLS ND HORIZONTLS RE INSTLLED THERML REK TO E SME LENGTH S VERTICL MULLIONS NOTE STEP - 6 PERIMETERS WHERE PPLICLE INSTLL PERIMETER MEMERS PER PPROVED SHOP DRWINGS. PERIMETER MEMERS CN OCCUR T HED, SILL OR JM CONDITIONS. ENCHMRK TO FCE OF PERIMETER MEMER PER PPROVED SHOP DRWINGS CONTINUOUS "F" PERIMETER 162-017 1" GLSS 162-176 1/4" GLSS 162-971 3 OF 12 MXIMUM TEMPORRY SPCING IS 30". IF MORE THN 50 MPH WIND IS EXPECTED INSTLL PRESSURE PLTES. SIZE ND SPCING OF WELD PER PPROVED SHOP DRWINGS DO NOT OVER TIGHTEN NCHOR CONNECTIONS. TIGHTEN TO "SNUG TIGHT" POSITION WITH PRTS ROUGHT INTO GOOD CONTCT. E SURE NY SPRING TYPE LOCK WSHERS RE COMPRESSED. THEN TIGHTEN PPROXIMTELY 1/2 MORE TURN. TTCH SHER LOCKS. STRUCTURL GLZED VERTICL DETILS SIMILR FOR "CPTURED VERTICLS" TYPICL INTERMEDITE SHER LOCKS 162-377 6" SYSTEM 162-378 7 1/2" SYSTEM STEP - 5 INSTLL 162-310 THERML REK 162-310 CPTURED VERTICLS/ HORIZONTLS NCHOR FSTENER LOCTIONS PER PPROVED SHOP DRWINGS SHER LOCK/NCHOR 128-396 SCREWS #12 x 7/16" PN HED TYPE THERML REK TO E THE SME LENGTH S THE HORIZONTL T STRUCTURL GLZED VERTICLS NOTE THERML REK TO E 1/4" SHORT T ECH END OF HORIZONTL T CPTURED VERTICLS FOR CPTURED VERTICLS INSTLL HED ND SILL END CPS 162-388 1" FRMING 162-389 1/4" FRMING SET IN SELNT USE GLZING 162-350 TEMPORRIES WITH 128-406 SCREWS. STEP - 7 INSTLL VERTICL MULLIONS DIMENSION UILDUP CHECK CHECK OVERLL FRME DIMENSIONS OUT EVERY FIVE MULLIONS ON LONG RUNS. THIS IS TO VOID DIMENSION UILDUP. 10 UNITS CHECK DIMENSION HED ND SILL SHER LOCKS 162-331 6" SYSTEM 162-332 7 1/2" SYSTEM REFERENCE INSTRUCTIONS 162-983 FOR EXTERIOR FRME PERIMETERS HED ND SILL SHER LOCKS 162-384 6" SYSTEM 162-385 7 1/2" SYSTEM DO NOT STRETCH WHEN REMOVING FROM COIL ND CRTON DO NOT STRETCH DURING INSTLLTION 162-310 THERML REK NOT REQUIRED T EXTERIOR FRME PERIMETERS SHOWN IN INSTRUCTIONS 162-983 ND T OPTIONL PERIMETER FILLERS 162-022 ND 162-023. 5 UNITS CHECK DIM. INSTLLTION INSTRUCTIONS PRT NO. 162-971 3 OF 12 DRWING: 95449-69 10/20/07
STEP - 7 INSTLL VERTICL MULLIONS STRUCTURL GLZED VERTICLS DETILS SIMILR FOR "CPTURED VERTICLS" "F" OR "T" NCHORS WHERE PPLICLE "F" ND "T" NCHOR FSTENER LOCTIONS PER PPROVED SHOP DRWINGS STEP - 7 INSTLL VERTICL MULLIONS STRUCTURL GLZED VERTICLS DETILS SIMILR FOR "CPTURED VERTICLS" HED/SILL SHER LOCK/NCHOR WHERE PPLICLE. CN NOT E USED WITH EXTERIOR FRME PERIMETERS SHOWN ON INSTRUCTIONS 162-983 STEP - 7 INSTLL VERTICL MULLIONS VERTICL SPLICE JOINTS WHERE PPLICLE. CPTURED VERTICLS STEP - 7 INSTLL VERTICL MULLIONS VERTICL SPLICE JOINTS WHERE PPLICLE. STRUCTURL GLZED VERTICLS 162-971 4 OF 12 REFERENCE INSTRUCTIONS 162-983 FOR EXTERIOR FRME PERIMETERS 162-314 6" SYSTEM T JMS 162-315 7 1/2" SYSTEM T JMS 162-342 6" SYSTEM T MULLIONS 162-343 7 1/2" SYSTEM T MULLIONS SLEEVE IS FCTORY TPED INTO THE OTTOM OF THE TOP VERTICL. SLEEVE IS FCTORY TPED INTO THE OTTOM OF THE TOP VERTICL. THESE SHER LOCKS MY NEED TO E REMOVED TO INSTLL NCHOR FSTENER THT MIGHT E LOCTED CLOSE TO THE MULLION 128-284 SCREWS #12 x 1 1/2 FLT HED TYPE FOR HORIZONTL TTCHMENT 128-396 SCREWS #12 x 7/16" PN HED TYPE REMOVE THE TPE ND LET THE SLEEVE SLIDE DOWN TO THE FCTORY PPLIED STOP SCREW "F" ND "T" NCHOR FSTENER LOCTIONS PER PPROVED SHOP DRWINGS T MULLION JM SIDE, PPLY (2) 128-396 SCREWS S SHOWN TO CENTER F-CLIPS S REQUIRED. 1/8" THE OVE SCREWS RE ONLY USED T THE OPTIONL SHER LOCK/NCHORS. STRUCTURL SHIMMING IS REQUIRED T SILL TO CCOMPLISH DESIGNED PERIMETER SEL WIDTH. NCHOR FSTENER LOCTIONS PER PPROVED SHOP DRWINGS USE TEMPORRY SPCERS FOR JOINT DIMENSION FIELD PPLIED FIXING SCREW 128-348 #10 x 1 1/4" FLT HED SELF DRILLING. SHOP PPLIED STOP SCREW 128-267 #12 x 1" PN HED TYPE SPLICE JOINT WHEN IT OCCURS T HORIZONTL. USE TEMPORRY SPCERS FOR JOINT DIMENSION REMOVE THE TPE ND LET THE SLEEVE SLIDE DOWN TO THE FCTORY PPLIED STOP SCREW FIELD PPLIED FIXING SCREW 128-348 #10 x 1 1/4" FLT HED SELF DRILLING. SHOP PPLIED STOP SCREW 128-267 #12 x 1" PN HED TYPE 1 1/4" SILL SHOWN HED SIMILR NCHOR FSTENER LOCTIONS PER PPROVED INSTLLTION INSTRUCTIONS SHOP DRWINGS PRT NO. 162-971 4 OF 12 DRWING: 95449-69 10/20/07
STEP - 8 INSTLL HED/SILL ND INTERMEDITE HORIZONTLS TUULR HORIZONTLS STEP - 8 INSTLL HED/SILL ND INTERMEDITE HORIZONTLS INSTLLING CEILING INTERMEDITE OPEN CK HORIZONTL 162-971 5 OF 12 STRUCTURL GLZED VERTICLS DETILS SME FOR "CPTURED VERTICLS" EXCEPT HORIZONTL THERML REK CUT 1/4" SHORT ECH END. 128-405 SCREWS #12 X 7/8" FLT HED TYPE REFERENCE INSTRUCTIONS 162-983 FOR EXTERIOR FRME PERIMETERS OPEN CK HORIZONTLS ND LST Y HORIZONTLS. FILLER VILLE WHEN OPEN CK IS EXPOSED ND T EYE LEVEL. STRUCTURL GLZED VERTICLS DETILS SME FOR "CPTURED VERTICLS" EXCEPT HORIZONTL THERML REK CUT 1/4" SHORT ECH END. INSTLLING STOOL INTERMEDITE OPEN CK HORIZONTL HED 128-405 SCREWS #12 X 7/8" FLT HED TYPE HED JOINT PLUG 162-321 1" FRMING 162-322 1/4" FRME MEMERS INTERMEDITE STEP - 9 INSTLL JOINT PLUGS PPLY SELNT TO THIS FCE OF JOINT PLUG CPTURED GLZED VERTICLS SILL CEILING LL SURFCES ND GROOVES MUST E CLENED PER THE SELNT MNUFCTURER'S RECOMMENDTIONS. JUST EFORE INSTLLING JOINT PLUGS PPLY SELNT S SHOWN FILLING POCKET ND DPTER GROOVE. SEL ROUND JOINT PLUG EDGES TOOL SELNT SECTION - FILL POCKET STOOL FILL DPTER GROOVE SEL ROUND JOINT PLUG EDGES TOOL SELNT THERML REK TO E SME LENGTH S HORIZONTL T SSG VERTICL SILL REFERENCE INSTRUCTIONS 162-983 FOR EXTERIOR FRME PERIMETERS THERML REK TO E 1/4" SHORT T ECH END OF HORIZONTLS T CPTURED VERTICL FCE VIEW INSTLLTION INSTRUCTIONS PRT NO. 162-971 5 OF 12 DRWING: 95449-69 10/20/07
STEP - 9 INSTLL JOINT PLUGS STRUCTURL GLZED VERTICLS PPLY SELNT S SHOWN FILLING POCKETS ND VERTICL GROOVES STEP - 10 INSTLL PERIMETER FILLERS ND DPTERS WHERE PPLICLE CPTURED VERTICLS JUST EFORE INSTLLING FILLERS ND DPTERS FCE SEL JOINTS T LL 4 CORNERS. LSO SEL SCREW HED T TOP HLF OF HORIZONTL LL SURFCES ND GROOVES MUST E CLENED PER THE SELNT MNUFCTURER'S RECOMMENDTIONS. STEP - 10 INSTLL PERIMETER FILLERS ND DPTERS WHERE PPLICLE CPTURED VERTICLS DPTER STEP - 10 INSTLL PERIMETER FILLERS ND DPTERS WHERE PPLICLE 162-971 6 OF 12 STRUCTURL GLZED VERTICLS PERIMETER FILLER JOINT PLUG 162-324 1" FRMING 162-325 1/4" FRMING PPLY SELNT TO OTH SIDES OF PLUG PERIMETER FILLER INSTLL VERTICL DPTER WITH 128-348 SCREWS #10 X 1-1/4" FLT HED SELF DRILLING SCREW. LOCTE MXIMUM 6" ND MINIMUM 4" FROM ECH END ND 9" ON CENTER GROOVE FOR INSTLLTION TOOL STRUCTURL GLZED VERTICLS T STEEL REINFORCING USE 128-401 #10 X 1" FLT HED TYPE SCREW. DRILL.154 DI. #23 DRILL INTO MULLION USING DPTER HOLES S PILOT SEL ROUND JOINT PLUG EDGES TOOL SELNT GROOVE FOR INSTLLTION TOOL USE PUTTY KNIFE, SMLL PRY R OR SCREW DRIVER DPTER INSTLLTION INSTRUCTIONS PRT NO. 162-971 6 OF 12 DRWING: 95449-69 10/20/07
STEP - 16 INSTLL GLSS STRUCTURL GLZED VERTICLS GLSS STEP - 17 INSTLL EXTERIOR PRESSURE PLTES HOW TO SET TORQUE LIMIT RECOMMEND USING TORQUE LIMIT TOOL 162-399 SEE NOTE. 1. TTCH NY CLIRTED TORQUE INDICTOR TO OUTPUT STU (1) ND DETERMINE PRESENT TORQUE SETTING WHILE HOLDING THE ODY (5), OR VICE-VERS. CPTURED VERTICLS INSTLL VERTICL PRESSURE PLTES T CPTURED VERTICLS 162-971 9 OF 12 NOTE - THE TORQUE LIMIT TOOL WS DESIGNED TO E USED WITH HND DRIVEN DEVICE. THE TOOL CN E DPTED TO DRILL MOTOR IF USED T MXIMUM SPEED OF PPROX. 300 RPM. HIGHER SPEEDS CN CUSE OVERHETING ND FFECT THE CCURCY. FTER PPROX. 1 HOUR OF TOOL USGE CHECK TORQUE SETTINGS WITH TORQUE WRENCH. INTERMEDITE HORIZONTL OVER 2. REMOVE SNP RING (2) ND LOCKING PLTE (3). 3. DJUST NUT (4) WITH OPEN-END WRENCH : CLOCKWISE TO INCRESE TORQUE, COUNTER- CLOCKWISE TO DECRESE TORQUE. 4. OTIN NEW TORQUE REDING WITH THE CLIRTED TORQUE INDICTOR. REPET PRECEDING STEP IF MORE DJUSTMENT IS NECESSRY TO RECH DESIRED LIMIT. JUST EFORE INSTLLING VERTICL PRESSURE PLTES PPLY GENEROUS MOUNT OF SELNT TO THE JOINT PLUG FCE FILLING JOINTS S SHOWN. GLSS 5. REPLCE LOCKING PLTE INTO NOTCHES ND INSTLL SNP RING. IF LOCKING PLTE DOES NOT "SET", MOVE THE DJUSTING NUT SLIGHTLY UNTIL IT DROPS IN PLCE. THE DIRECTION IS EST DETERMINED Y WHETHER MINIMUM TORQUE PPLICTION OR MXIMUM ONE IS DESIRED. CLEN JOINT PER SELNT MNUFCTURER'S RECOMMENDTIONS - TOOL EXCESS SELNT HED CONDITION SILL SME VERTICL STOPS 1/2" SHORT T HED ND SILL CONDITIONS STRUCTURL GLZED VERTICLS TEMPORRY RETINERS FOR STRUCTURL GLZED VERTICLS. 5 2 THE LOCTION OF TEMPORRY EXTERIOR INFILL RETINERS SHOULD E T MXIMUM SPCING OF 30" ON CENTER. IF WINDS GRETER THN 50 MPH (80KPH) RE EXPECTED, DDITIONL TEMPORRIES MY E REQUIRED. CONSULT YOUR SELNT ND/OR INFILL SUPPLIER FOR SPCING RECOMMENDTIONS. GLZING TEMPORRY 162-353 1 INSTLL PRESSURE PLTES USING SCREWS 128-406 1/4-14 X 1" HEX WSHER HED TYPE. SCREWS RE TO E LOCTED 9" ON CENTER. LWYS LOCTE SCREW S CLOSE S POSSILE TO HORIZONTL JOINT. THIS WILL PROVIDE MXIMUM PRESSURE FOR THE CRITICL JOINT SELS. 3 4 TOOL EXCESS SELNT PERIMETER FILLER HED CONDITION SILL SME VERTICL STOPS 1/2" SHORT T HED ND SILL CONDITIONS INSTLL HORIZONTL PRESSURE PLTES WITH WEEP HOLES TOWRDS TOP OF HORIZONTL. INSTLL WITH SCREWS 128-400 T 1" GLSS #12 X 2-1/4 PH HD TYPE USE SCREW 128-284 T 1/4" GLSS #12 X 1-1/2 FL HD TYPE T CORNERS ND SPLYS RETINERS SHOULD E MDE FROM GOOD QULITY HRDWOOD. THESE RETINERS RE NOT SUPPLIED Y KWNEER. T ECH HORIZONTL ND VERTICL PRESSURE PLTE INSTLL TWO SCREWS PRT WY, THEN INSTLL THE THIRD SCREW LL THE WY, ND THEN TIGHTEN THE FIRST TWO SCREWS. THIS ELIMINTES LTERL WLKING OF THE PRESSURE PLTE POSITION. TORQUE LL SCREWS TO 95 TO 100 INCH POUNDS. DURING COLD WETHER, TORQUE SCREWS TO 50 INCH POUNDS UNTIL LL 4 SIDES HVE EEN CLMPED. THEN TORQUE SCREWS TO 95 TO 100 INCH POUNDS. - TOOL EXCESS SELNT INSTLLTION INSTRUCTIONS PRT NUMER 162-971 9 OF 12 DRWING: 95449-69 10/20/07
STEP - 17 INSTLL EXTERIOR PRESSURE PLTES INSTLL VERTICL PRESSURE PLTES T CPTURED VERTICLS VERTICL EXPNSION JOINTS INSTLL HORIZONTL PRESSURE PLTES T CPTURED VERTICLS CENTER HORIZONTL PRESSURE PLTES SO END GPS RE EQUL. INTERMEDITE HORIZONTL OVER REFERENCE INSTRUCTIONS 162-983 FOR EXTERIOR FRME PERIMETERS SEL ETWEEN PRESSURE PLTE ND HED/SILL END CP S SHOWN. D HED HORIZONTL SILL SME INSTLL HORIZONTL PRESSURE PLTES T SSG VERTICLS 162-971 10 OF 12 NOTE - THE TORQUE LIMIT TOOL WS DESIGNED TO E USED WITH HND DRIVEN DEVICE. THE TOOL CN E DPTED TO DRILL MOTOR IF USED T MXIMUM SPEED OF PPROX. 300 RPM. HIGHER SPEEDS CN CUSE OVERHETING ND FFECT THE CCURCY. FTER PPROX. 1 HOUR OF TOOL USGE CHECK TORQUE SETTINGS WITH TORQUE WRENCH. D E TOP OF VERTICL MULLION TO TOP OF PRESSURE PLTE IS 1-1/2" - SEL JOINTS S SHOWN. TOOL SELNT. THIS SEL IS TO JOIN ND DHERE TO THE JOINT PLUG SELS. CLEN JOINT PER SELNT MNUFCTURER'S RECOMMENDTIONS C D-D C E SEL JOINTS S SHOWN. TOOL SELNT. THIS SEL IS TO JOIN ND DHERE TO THE JOINT PLUG SELS. CLEN JOINT PER SELNT MNUFCTURER'S RECOMMENDTIONS T TOP PRESSURE PLTE LOCTE SCREW CLOSE TO THE MULLION JOINT UT NOT ELOW THE JOINT. DO NOT LET THE SEL INTERFERE WITH THE COVER SNP. - VERTICL STOPS 1/2" SHORT OF END. DO NOT LET THE SEL INTERFERE WITH THE COVER SNP. E-E 027-857 JUST EFORE PPLYING PRESSURE PLTE PPLY GENEROUS MOUNT OF SELNT TO THE JOINT PLUG FCE. CLEN JOINT PER SELNT MNUFCTURER'S RECOMMENDTIONS CLEN JOINT PER SELNT MNUFCTURER'S RECOMMENDTIONS FCE VIEW PERIMETER FILLER HED HORIZONTL SILL SME FCE VIEW DO NOT LET THE SEL INTERFERE WITH THE COVER SNP. D D E C-C COMPLETELY SEL JOINT. DO NOT LET SELNT INTERFERE WITH COVER SNP OVERLP PRESSURE PLTE FCE CRETING ND-ID SEL C C E SEL JOINTS S SHOWN. TOOL SELNT. THIS SEL IS TO JOIN ND DHERE TO THE JOINT PLUG SELS. INSTLLTION INSTRUCTIONS PRT NUMER 162-971 10 OF 12 DRWING: 95449-69 10/20/07
162-971 11 OF 12 STEP - 17 INSTLL EXTERIOR PRESSURE PLTES INSTLL HORIZONTL PRESSURE PLTES T SSG VERTICLS INSTLL HORIZONTL PRESSURE PLTES T SSG VERTICLS STEP - 18 INSTLL PERIMETER SELS INSTLL HORIZONTL PRESSURE PLTES T SSG VERTICLS - REFERENCE INSTRUCTIONS 162-983 FOR EXTERIOR FRME PERIMETERS - 027-857 - PERIMETER WETHER SELS RE INSTLLED T THE PRESSURE PLTE LOCTION S DETILED ELOW. (THIS SEL SHOULD E INSTLLED EFORE COVERS RE PPLIED WHEN COVERS DEEPER THN 3/4" RE USED) EXTERIOR COSMETIC SELS T THE COVER MY E PPLIED T THE HED ND JMS ONLY. SILL COVERS MUST REMIN OPEN TO LLOW WTER DRINGE TO THE EXTERIOR. HED HORIZONTL SILL SME PERIMETER FILLER HED HORIZONTL SILL SME OPTIONL COSMETIC SEL REQUIRED WETHER SEL OPTIONL COSMETIC SEL HED CONDITION COVER DEPTH DO NOT SEL OVER WEEP HOLES WEEP RE SILL CONDITION HED HORIZONTL SILL SME PERIMETER FILLER HED HORIZONTL SILL SME REQUIRED WETHER SEL OPTIONL COSMETIC SEL JM CONDITION REQUIRED WETHER SEL OPTIONL COSMETIC SELS COMPLETELY SEL HORIZONTL PRESSURE PLTE JOINT. DO NOT LET SELNT INTERFERE WITH COVER SNP CLEN JOINT PER SELNT MNUFCTURER'S RECOMMENDTIONS COMPLETELY SEL HORIZONTL PRESSURE PLTE JOINT. DO NOT LET SELNT INTERFERE WITH COVER SNP CLEN JOINT PER SELNT MNUFCTURER'S RECOMMENDTIONS COMPLETELY SEL HORIZONTL PRESSURE PLTE JOINT. DO NOT LET SELNT INTERFERE WITH COVER SNP CLEN JOINT PER SELNT MNUFCTURER'S RECOMMENDTIONS INSTLLTION INSTRUCTIONS PRT NO. 162-971 11 OF 12 DRWING: 95449-87 02/17/12