GB Operatng nstructons Last updated: 01.2014 Parkng barrer Parc 200 / Parc 200 speed
1. Meanng of symbols 2. Table of contents Advce Cauton! Danger of personal njury! The followng safety advce must be observed at all tmes so as to avod personal njury! Attenton! Danger of materal damage! The followng safety advce must be observed at all tmes so as to avod materal damage! Advce / Tp Check Reference 1. Meanng of symbols.........................2 2. Table of contents............................2 3. General safety advce........................3 4. Product overvew............................4 4.1 Parc 200 supply package..................4 4.2 Dmensons............................5 4.3 Optons...............................6 5. Preparaton for mountng.....................6 5.1 General notes..........................6 5.2 Checks................................7 5.3 Concrete foundaton layout................7 5.4 Cablng layout..........................8 6. Installaton.................................8 6.1 Mountng the parkng barrer cabnet........8 6.2 Mountng the parkng barrer arm...........9 6.3 Mountng the sprng unts.................9 6.4 Settng the boom poston................10 6.5 Reversng the sde of openng.............11 6.6 Connecton of control elements...........12 7. Operaton.................................12 7.1 Operatng systems......................12 7.2 Release..............................13 8. Attachment................................14 8.1 Techncal Data for Parc 200 / Parc 200 speed..14 8.2 Colour codng and assgnment of counterbalance sprng...................14 8.3 Mantenance..........................15 8.4 Dsassembly...........................15 8.5 Declaraton of Incorporaton / Declaraton of performance 2013-02........16 Identfcaton plate on parkng barrer Type: Art. No.: Product No.: 2 Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313)
3. General safety advce Please read carefully! IMPORTANT SAFETY INSTRUCTIONS: IMPORTANT - PLEASE OBSERVE ALL SAFETY INSTRUCTIONS TO PREVENT INJURY TO PERSONS. PLEASE KEEP THESE INSTRUCTIONS FOR FURTHER USE. IMPORTANT INSTRUCTIONS FOR SAFE INSTALLATION: IMPORTANT - INCORRECT INSTALLATION CAN RESULT IN SERIOUS INJURY. PLEASE FOLLOW ALL INSTALLATION INSTRUCTIONS. Target group Ths operator system may only be nstalled, connected and put nto operaton by qualfed and traned professonals! Qualfed and traned specalst personnel are persons - who have knowledge of the general and specal safety regulatons, - who have knowledge of the relevant electro-techncal regulatons, - wth tranng n the use and mantenance of sutable safety equpment, - who are suffcently traned and supervsed by qualfed electrcans, - who are able to recognse the partcular hazards nvolved when workng wth electrcty, - wth knowledge regardng applcatons of the EN 12635 standard (nstallaton and usage requrements). Warranty For an operatons and safety warranty, the advce n ths nstructon manual has to be observed. Dsregardng these warnngs may lead to personal njury or materal damage. If ths advce s dsregarded, the manufacturer wll not be lable for damages that mght occur. The warranty does not nclude batteres, rechargeable batteres, fuses and bulbs. To avod nstallaton errors and damage to the parkng barrer system, t s essental that the nstallaton nstructons are followed. The system may only be used after thoroughly readng the respectve mountng and nstallaton nstructons. The nstallaton and operatng nstructons must be submtted to the parkng barrer operator and kept n a safe place. They contan mportant advce for operaton, checks and mantenance. Ths tem s produced accordng to the drectves and standards mentoned n the Manufacturer's Declaraton and n the Declaraton of Conformty. The product has left the factory n perfect condton wth regard to safety. Power-operated nstallatons must be checked by an expert (and ths must be documented) before they are put nto operaton and thereafter as requred, but at least once a year. Correct use The parkng barrer system s desgned exclusvely for use n access zones. Its purpose s to provde safe access for goods and vehcles, whether guded or drven by persons, n ndustral parks or resdental areas. Please note that ths operator system must only be used wth the barrer arms and counterbalance sprngs suppled by the manufacturer. Informaton on nstallng the parkng barrer system Render any nstallatons noperable that wll no longer be needed after the parkng barrer system has been nstalled. Before commencng cablng works t s very mportant to dsconnect the operator system from the electrcty supply. Ensure that the electrcty supply remans dsconnected throughout the cablng works. Adhere to the local protecton regulatons. Use only fxng materals whch are approved for the substrate concerned. Lay the electrcty supply cables and control cables; these MUST be lad separately. The controls voltage s 24 V DC. Mount all pulse generators and control devces (e.g. rado code keypad) wthn sght of the parkng barrer and at a safe dstance from any movng parts of the parkng barrer system. Advce on commssonng the park barrer system To ensure proper operaton of the system wthn the CEN (European Commttee for Standardsaton) states t s essental that the relevant European health and safety drectves and standards are taken nto account. The techncal data relatng to envronmental condtons, degree of protecton, loadng and duty cycle must be compled wth. All parkng barrer users must be nstructed n the system s operaton once t has been nstalled. Make sure that chldren cannot play wth the controls. Make sure before operatng the parkng barrer that no objects or people are n the danger zone of the parkng barrer. Test all exstng emergency command devces. Never place your hands n a movng parkng barrer or movng parts. Be aware of possble crushng and shearng hazards posed by the parkng barrer system. The EN 13241-1 regulatons must be observed. Advce on servcng the parkng barrer system To ensure proper operaton, the followng tems must be checked regularly and repared f necessary. Before any works to the parkng barrer system are undertaken, the operator system must be dsconnected from the mans. Check once a month to ensure that the operator system reverses f the parkng barrer encounters an obstacle. Dependng on the operatonal drecton of the parkng barrer, place a 1,500 mm hgh obstacle n ts path. Perform a check on the OPEN and CLOSE automatc cut-out settng. Check all movable parts of the parkng barrer system. Check the parkng barrer system for wear or damage. Inspect the safety devces nstalled every sx months. Informaton on cleanng the parkng barrer system Never use water jets, hgh pressure cleaners, acds or bases for cleanng. Besde the advce n these nstructons, please observe the general safety and accdent preventon regulatons! Our sales and supply terms and condtons are effectve. Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313) 3
4. Product overvew 4.1 Parc 200 supply package Accessores 4.1 / 3 Standard package 4.1 / 1! 1 1 Parc 200 cabnet 10 Boom end support post wth cradle secton, heghtadjustable (optonal where barrer arm s less than 4 m long, essental where barrer arm s 4 metres or more n length) 4.1 / 2 4.1 / 4 2 3!@ 9! 5 8 7 6 4 11 Support post, empty housng 12 Manual release mechansm 2 Barrer arm (boom) (3 m, 4 m) 3 Release key 4 Sprng unt 5 Counter bracket 6 Key (2x) 7 Screw set 8 Heavy-duty dowel M10 9 Full-floatng axle 4.1 / 5!!# 13 Magnetc base aeral (Dgtal 178) 14 Barrer arm (boom) LED lght 4 Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313)
500 4. Product overvew 4.2 Dmensons Parc 200 park barrer wth artculated arm 4.2 / 2 G Parc 200 4.2 / 1 A B E F 1200 H 995 C 80 800 D 40 400 320 955 E F G H Clearance heght wth 2000 mm rubber profle Clearance heght wthout 2030 mm rubber profle Access wdth 2000 mm Requred heght 2150 mm A Barrer arm (boom) length B Span = barrer arm length -300 C Coled cable ductng D Photocell barrer adapter Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313) 5
4. Product overvew 5. Preparaton for mountng 4.3 Optons 5.1 General notes Parkng barrer cabnet on the left 4.3 / 1 The pctures n these nstructons are not true-to-scale. Dmensons are always gven n mllmetres (mm)! For correct mountng you wll need the followng tools: 5.1 / 1 10 / 13 / 17 / 19 / 22 / 24 2 Parkng barrer cabnet on the rght 4.3 / 2 3 ø 10 3 / 5 / 6 Parkng barrer cabnet on the left wth artculated arm Transport The barrer arm housng must - be transported uprght and - be prevented from fallng over. 4.3 / 3 Parkng barrer cabnet on the rght wth artculated arm 4.3 / 4 6 Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313)
5. Preparaton for mountng 5.2 Checks Attenton! In order to guarantee correct mountng, carry out the followng checks before nstallng. Supply package Check the package to ensure that all the parts are ncluded. Check that you have all the addtonal components that are necessary for your partcular nstallaton requrements. Parkng barrer system Ensure that a sutable mans connecton and a mans dsconnecton faclty are avalable for your parkng barrer system. The mnmum cross-sectonal area of the earth cable s 3 x 1.5 mm 2. Ensure that all cables are sutable for outdoor use (UV resstant and cold resstant). Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313) 7 5.3 Concrete foundaton Attenton! To prevent damage to the concrete foundaton, the sze of the foundaton base must comply wth the nstructons. layout 5.3 / 1 600 B A 274 A Drveway B Duct ppe for cablng to control panel and mans supply cablng The depth of the concrete base must be at least 800 mm. 197 520
5. Preparaton for mountng 6. Installaton 5.4 Cablng layout 6.1 Mountng the parkng barrer cabnet Advce: Ths s just an example of a cablng layout; the layout can vary dependng on the assocated equpment. Attenton! A concrete foundaton accordng to the specfcatons must be provded and be hardened to ensure satsfactory long-term operaton of the parkng barrer system. 5.4 / 1 3 x 1,5 mm 2 230 V / AC 8 7 3 6.1 / 1 5 1 2 7 2 x 0,8 mm 2 4 5 2 x 0,5 mm 2 3 x 1,5 mm 2 230 V / AC 6 Open the cabnet. 6.1 / 2 1 Photocell 2 Sgnal lght 3 Code button, transponder, Con acceptor 4 Key swtch 5 Mans solator swtch (mans dsconnecton faclty) 6 Mans supply cable 7 Inducton loops 8 Magnetc lock Reference: For the nstallaton and cablng of the sensors, control elements and safety equpment, the relevant nstallaton nstructons must be observed. Screw the cabnet to the concrete base. 6.1 / 3 Insert aeral through the cable ductng (optonal). 8 Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313)
6. Installaton 6.2 Mountng the parkng barrer arm 6.3 Mountng the sprng unts Attenton! - To avod damagng the barrer arm, the barrer arm must be ftted by two people. The barrer arm must be supported to prevent t from fallng before t s securely fxed n place. - If the sde on whch the barrer arm opens needs to be changed over, ths must be carred out before the barrer arm s ftted. Cauton! - To prevent the unlocked barrer arm from fallng, the barrer arm must be locked when t s n an uprght poston. - To ensure correct operaton, nuts (C) must be locked after adjustng the tenson of the sprng. Reference: The procedure for reversng the sde of openng s descrbed n Secton 6.5. Release the operator. Rase the barrer arm untl t s n an uprght poston. Lock the operator. Advce: The shaft must be nserted so that the lockng screw (A) engages wth groove (B). Reference: The procedure for releasng the operator s descrbed n Secton 7.2. 6.2 / 1 B A C 6.3 / 1 B B A A Remove the cover (C). Fx the barrer arm adapter. 6.2 / 2 Push the drll-holes (A) onto the threaded rods (B). Screw on the sprng unt. Release the operator. Screw the barrer arm on n a horzontal poston. Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313) 9
6. Installaton 6.3 / 2 6.4 Settng the boom poston C To set the barrer arm poston The barrer arm must be lowered and n a horzontal poston. Reference: The nstructons for settng the OPEN and CLOSED barrer arm postons can be found n the control unt documentaton. Set the tenson of the sprng. Lock the nuts (C). To set the sprng buffers Lock the operator. 6.3 / 3 6.4 / 1 B A B Remove the cover (A). Advce: The tenson of the sprng must be adjusted so that the barrer arm s automatcally held n place when t s n a half-opened poston. Adjust the sprng buffers (B) n pars. Tghten the sprng buffers (B). Advce: The sprng buffers (B) must be set so that they are under slght tenson. 10 Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313)
6. Installaton 6.5 Reversng the sde of openng 6.5 / 4 Release the operator. Reference: The procedure for releasng the operator s descrbed n Secton 7.2. 6.5 / 1 Gve controls a 180 turn. Screw hnges onto opposte sde. Attach controls to cabnet. 6.5 / 5 A Take out barrer arm shoulder. 6.5 / 2 Screw reference pont magnet (A) onto opposte sde. Gve barrer arm shoulder a 180 turn and replace n the cabnet. Remove plug from socket. 6.5 / 3 Attenton! After changng the openng sde, the rotatonal drecton must be altered accordngly n order to prevent damage to property. To change the rotatonal drecton, swap the leads at termnals 1 and 2 of the motor connecton XM70A. Reference: The motor connecton XM70A s descrbed n the control unt documentaton. Lock the operator. Remove controls from cabnet. Remove cable from cabnet. Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313) 11
6. Installaton 7. Operaton 6.6 Connecton of control elements 7.1 Operatng systems Reference: A descrpton of the control unt can be found n the relevant documentaton for the control unt. The followng operatng devces can be used to actuate the parkng barrer system: - Code keypad - Transponder - Con acceptor - Inducton loop - Hand transmtter / rado technology Reference: Please refer to the relevant manuals for nstructons on usng the operatng devces. 12 Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313)
7. Operaton 7.2 Release Lockng 7.2 / 2 Releasng Attenton! To prevent damage, the barrer arm must only be released f the sprng unt s fully ntact. The barrer arm may move upwards durng ths procedure. A B 7.2 / 1 Place release key (A) over red release nut (B). B Turn release key (A) approx. 180 n a clockwse drecton untl t stops. Partally rase and lower barrer arm manually. A The transmsson and drve shaft are now mechancally engaged. The parkng barrer can only be moved wth the motor. The electrc crcut n the controls s closed agan and the controls are n operaton. Place release key (A) over red release nut (B). Turn release key (A) approx. 180 n an antclockwse drecton untl t stops. Partally rase and lower barrer arm manually. The transmsson s now mechancally dsengaged from the drve shaft. The parkng barrer can only be moved manually. The electrc crcut n the controls s nterrupted and the controls are out of operaton. A correspondng message s dsplayed. Reference: The messages are explaned n the documentaton suppled wth the control unt. Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313) 13
8. Attachment 8.1 Techncal Data for Parc 200 / Parc 200 speed 8.2 Colour codng and assgnment of counterbalance sprng Electrcal data Nomnal voltage *) V 230 / 260 Nomnal frequency Hz 50 / 60 Power consumpton A 1.1 Power nput - operaton KW 0,25 Power nput - stand-by W 3.6 Operatng mode (operatng tme) ED 90% Control voltage V DC 24 Protecton category, motor unt IP 65 *) subject to country-specfc alternatons Mechancal data Openng tme (barrer specfc) sec. 3-10 Movement cycles per day Barrer arm length: up to 2.3 m Barrer arm length: up to 3.3 m Barrer arm length: up to 4.3 m 1,500 1,000 750 Type of barrer Barrer length n metres Counter balan ce sprng, red #91386 (number) Counter - balance sprng, whte #91385 (number) Barrer arm Barrer arm wth mpact protecton Barrer arm wth 8.2 kω swtchng strp Artculated arm 2,3 3,3 4,3 2,3 3,3 4,3 2,3 3,3 4,3 2 3 0 2 1 2 1 1 2 1 3 0 2 3 1 2 4 1 2 4 0 General data Motor unt dmensons mm 405x325x1210 Weght kg 55 Sound pressure level db (A) < 70 Temperature range C -20 +60 Advce: Barrer arms of 4 metres and more n length also requre an end support post wth a cradle secton. Features / Safety functons Reference pont technology Soft-Start / Soft-Stop Automatc cut-out Blockng protecton Undervoltage protecton Excess travel stop Electronc travel cut-out Connecton for pushbuttons, code buttons and key swtches Error messages x x x x x x x x x 14 Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313)
8. Attachment 8.3 Mantenance 8.4 Dsassembly Cauton! To avod njures, the barrer arm must be secured aganst fallng. Cauton! To avod njures, the barrer arm must be secured aganst fallng. To ensure trouble-free operaton, every 100,000 cycles: - the sprngs must be replaced, - the sprng holder n the shoulder wheel must be cleaned and lubrcated wth grease. To dsassemble, follow assembly nstructons n reverse order. Lubrcatng the sprng holder 10.3 / 1 A B Open the door. Remove the cover. Release the operator. Open the barrer arm. Take all the sprngs out of the sprng holder (A). Remove the sprng holder (A) from the shoulder wheel (B). Clean and grease the sprng holder (A). Assemble all the components agan n the reverse order. Reference: The procedure for releasng the operator s descrbed n Secton 7.2. Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313) 15
8. Attachment 8.5 Declaraton of Incorporaton / Declaraton of performance 2013-02 Intended use Ths barrer system s manufactured for nstallaton n access and entry areas n commercal or prvate facltes, n complance wth the harmonsed standards DIN EN 13241-1:2003. Type tested by TÜV Nord Cert GmbH - 0044 We hereby declare that n ts desgn and constructon, and n the form as delvered, the product mentoned below comples wth the relevant basc requrements of the EC Machnery Drectve (2006/42/EC). Ths declaraton shall no longer be vald f changes are made to the product wthout our authorsaton. Assessment of constancy of performance accordng to system 3 Declared performance: Resstance to wnd load Class 1 Operatng forces / closng forces Pass Safe openng Pass Product: Parkng barrer system Parc 200, Parc 200 speed Revsonsstand: R01 In addton, the machnery s n conformty wth all regulatons of the EU Constructon Products Regulaton No. 305/2011, the Electromagnetc Compatblty Drectve 2004/108/EC and the Low Voltage Drectve 2006/95/EC. Machnery Drectve 2006/42/EC Health and safety requrements appled accordng to Annex 1 EN 60204-1:2007 EN ISO 12100:2011 EN ISO 13849-1:2008 Cat. 2 / PLC for the functons of power lmtaton and end poston detecton EMC electromagnetc compatblty 2004/108/EC EN 55014-1:2012 EN 61000-3-2:2010 EN 61000-3-3:2009 EN 61000-6-2:2006 EN 61000-6-3:2011 01.09.2013 M. Hörmann Management Person authorsed to comple the relevant techncal documentaton: Marantec Antrebs- und Steuerungstechnk GmbH & Co. KG Remser Brook 11 33428 Marenfeld Germany Phone: +49 5247 705-0 Low voltage drectve 2006/95/EC EN 60335-1:2012 EN 60335-2-103:2010 The relevant techncal documentaton s compled n accordance wth Annex VII(B) of the Machnery Drectve 2006/42/EC. We undertake to transmt, n response to a reasoned request by the market survellance authortes, ths nformaton n electronc form wthn a reasonable term. 16 Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313)
Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313) 17
18 Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313)
Installaton and Operatng Instructons, Parc 200, Parc 200 speed GB (#106313) 19
Englsh Orgnal operatng nstructons protected by copyrght. No part of ths manual may be reproduced wthout our pror consent. Subject to changes whch are n the nterest of techncal mprovements. 106313 1 - GB 360407 - M - 0.5-0114