32K X 8 STATIC RAM PRELIMINARY Features High-speed: 35, 70 ns Ultra low DC operating current of 5mA (max.) Low Power Dissipation: TTL Standby: 3 ma (Max.) CMOS Standby: 20 µa (Max.) Fully static operation All inputs and outputs directly compatible Three state outputs Ultra low data retention current (V CC = 2V) Single 5V ± 10% Power Supply Packages 28-pin TSOP (Standard) 28-pin 600 mil PDIP 28-pin 330 mil SOP (450 mil pin-to-pin) Description The is a 262,144-bit static random access memory organized as 32,768 words by 8 bits. It is built with MOSEL VITELIC s high performance CMOS process. Inputs and threestate outputs are TTL compatible and allow for direct interfacing with common system bus structures. Functional Block Diagram A 0 Row Decoder 512 x 512 Memory Array V CC GND A 8 I/O 0 Input Data Circuit Column I/O Column Decoder I/O 7 A 9 A 14 CE OE WE Control Circuit 518256-01 Device Usage Chart Operating Temperature Range Package Outline Access Time (ns) Power T P F 35 70 L LL Temperature Mark 0 C to 70 C Blank 40 C to +85 C I 1
Pin Descriptions A 0 A 14 Address Inputs These 15 address inputs select one of the 32,768 x 8 bit segments in the RAM. CE Chip Enable Inputs CE is an active LOW input. Chip Enable must be LOW when reading from or writing to the device. When HIGH, the device is in standby mode with I/O pins in the high impedance state. OE Output Enable Input The Output Enable input is active LOW. When OE is LOW with CE LOW and WE HIGH, data of the selected memory location will be available on the I/O pins. When OE is HIGH, the I/O pins will be in the high impedance state. WE Write Enable Input An active LOW input, WE input controls read and write operations. When CE and WE inputs are both LOW, the data present on the I/O pins will be written into the selected memory location. I/O 0 I/O 7 Data Input and Data Output Ports These 8 bidirectional ports are used to read data from and write data into the RAM. V CC GND Power Supply Ground Pin Configurations (Top View) 28-Pin DIP/SOP 28-Pin TSOP (Standard) A 14 A 12 A 7 A 6 A 5 A 4 A 3 A 2 1 2 3 4 5 6 7 8 28 27 26 25 24 23 22 21 V CC WE A 13 A 8 A 9 A 11 OE A 10 OE A11 A9 A8 A13 WE VCC A14 A12 A7 A6 A5 A4 A3 22 23 24 25 26 27 28 1 2 3 4 5 6 7 21 20 19 18 17 16 15 14 13 12 11 10 9 8 518256-03 A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 GND I/O2 I/O1 I/O0 A0 A1 A2 A 1 9 20 CE A 0 10 19 I/O 7 I/O 0 11 18 I/O 6 I/O 1 12 17 I/O 5 I/O 2 13 16 I/O 4 GND 14 15 I/O 3 518256-01 2
Part Number Information V 62 C 51 8 256 MOSEL-VITELIC MANUFACTURED 62 = STANDARD SRAM FAMILY C = CMOS PROCESS 51 = 5V OPERATING VOLTAGE ORGANIZATION 8 = 8-bit DENSITY 256K PWR. SPEED 35 ns 70 ns PKG TEMP. L = LOW POWER LL = DOUBLE LOW POWER BLANK = 0 C to 70 C I = -40 C to +85 C T = TSOP STANDARD P = 600 mil PDIP F = 330 mil SOP (450 mil Pin-to-Pin) 518256-05 Absolute Maximum Ratings (1) Symbol Parameter Commercial Industrial Units V CC Supply Voltage -0.5 to +7-0.5 to +7 V V N Input Voltage -0.5 to +7-0.5 to +7 V V DQ Input/Output Voltage Applied V CC + 0.5 V CC + 0.5 V T BIAS Temperature Under Bias -10 to +125-65 to +135 C T STG Storage Temperature -65 to +150-65 to +150 C NOTE: 1. Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Capacitance* T A = 25 C, f = 1.0MHz Symbol Parameter Conditions Max. Unit Truth Table Mode CE OE WE I/O Operation C IN Input Capacitance V IN = 0V 6 pf C OUT Output Capacitance V I/O = 0V 8 pf NOTE: * This parameter is guaranteed and not tested. Standby H X X High Z Read L L H D OUT Read L H H High Z Write L X L D IN NOTE: X = Don t Care, L = LOW, H = HIGH 3
DC Electrical Characteristics (over all temperature ranges, V CC = 5V ± 10%) Symbol Parameter Test Conditions Min. Typ. Max. Units V IL Input LOW Voltage (1,2) -0.5 0.8 V V IH Input HIGH Voltage (1) 2.2 6 V I IL Input Leakage Current V CC = Max, V IN = 0V to V CC -2 2 µa I OL Output Leakage Current V CC = Max, CE = V IH, V OUT = 0V to V CC -2 2 µa V OL Output LOW Voltage V CC = Min, I OL = 2.1mA 0.4 V V OH Output HIGH Voltage V CC = Min, I OH = -1mA 2.4 V Symbol Parameter Power Com. (4) Ind. (4) Units I CC I CC1 I SB I SB1 Operating Power Supply Current, CE = V IL Output Open, V CC = Max., f = 0 Average Operating Current, CE V IL Output Open, V CC = Max., f = f MAX (3) TTL Standby Current CE V IH, V CC = Max. CMOS Standby Current, CE V CC 0.2V, V IN V CC 0.2V or V IN 0.2V, V CC = Max. READ 5 6 ma WRITE 40 50 60 70 ma L 4 5 ma LL 3 4 L 60 70 µa LL 20 30 NOTES: 1. These are absolute values with respect to device ground and all overshoots due to system or tester noise are included. 2. V IL (Min.) = -3.0V for pulse width < 20ns. 3. f MAX = 1/t RC. 4. Maximum values. AC Test Conditions Input Pulse Levels 0 to 3V Input Rise and Fall Times 5 ns Timing Reference Levels 1.5V Key to Switching Waveforms WAVEFORM INPUTS OUTPUTS MUST BE STEADY WILL BE STEADY Output Load see below AC Test Loads and Waveforms +5V 1800 Ω I/O Pins MAY CHANGE FROM H TO L MAY CHANGE FROM L TO H DON'T CARE: ANY CHANGE PERMITTED WILL BE CHANGING FROM H TO L WILL BE CHANGING FROM L TO H CHANGING: STATE UNKNOWN 990 Ω C L = 30 pf* DOES NOT APPLY CENTER LINE IS HIGH IMPEDANCE OFF STATE * Includes scope and jig capacitance 518256-06 4
Data Retention Characteristics Symbol Parameter Power Min. Typ. (2) Max. Units V DR V CC for Data Retention CE V CC 0.2V 2.0 5.5 V I CCDR Data Retention Current V DR = 3.0V, CE V DR 0.2V Com l L 0.5 50 µa LL 0.5 15 Ind. L 70 LL 20 t CDR Chip Deselect to Data Retention Time 0 ns t R Operation Recovery Time (see Retention Waveform) t RC (1) ns NOTES: 1. t RC = Read Cycle Time 2. T A = +25 C. Low V CC Data Retention Waveform Data Retention Mode V CC 4.5V V DR 2V 4.5V t CDR t R CE V CC 0.2V CE 2.2V 2.2V 518256-07 5
AC Electrical Characteristics (over all temperature ranges) Read Cycle Parameter Name Parameter -35-70 Min. Max. Min. Max. Unit t RC Read Cycle Time 35 70 ns t AA Address Access Time 35 70 ns t ACS Chip Enable Access Time 35 70 ns t OE Output Enable to Output Valid 15 30 ns t CLZ Chip Enable to Output in Low Z 5 5 ns t OLZ Output Enable to Output in Low Z 5 5 ns t CHZ Chip Disable to Output in High Z 0 20 0 20 ns t OHZ Output Disable to Output in High Z 0 20 0 20 ns t OH Output Hold from Address Change 5 5 ns Write Cycle Parameter Name Parameter -35-70 Min. Max. Min. Max. Unit t WC Write Cycle Time 35 70 ns t CW Chip Enable to End of Write 35 60 ns t AS Address Setup Time 0 0 ns t AW Address Valid to End of Write 35 60 ns t WP Write Pulse Width 25 50 ns t WR Write Recovery Time 0 0 ns t WHZ Write to Output High-Z 0 20 0 25 ns t DW Data Setup to End of Write 25 30 ns t DH Data Hold from End of Write 0 0 ns t OHZ Output Disable to Output in High Z 0 25 0 30 ns t OW Output Active from End of Write 5 5 ns 6
Switching Waveforms (Read Cycle) Read Cycle 1 (1, 2) t RC ADDRESS t AA OE t OE t OLZ t OHZ (5) I/O 518256-08 Read Cycle 2 (1, 2, 4) t RC ADDRESS t OH t AA t OH I/O 518256-09 Read Cycle 3 (1, 3, 4) ADDRESS t ACS CE I/O t CLZ (5) t CHZ (5) 518256-10 NOTES: 1. WE = V IH. 2. CE = V IL. 3. Address valid prior to or coincident with CE transition LOW. 4. OE = V IL. 5. Transition is measured ±500mV from steady state with C L = 5pF. This parameter is guaranteed and not 100% tested. 7
Switching Waveforms (Write Cycle) Write Cycle 1 (WE Controlled) (4) t WC ADDRESS t CW (6) t WR (2) CE t AS t AW WE t WP (1) OUTPUT t WHZ (3) t DW t DH INPUT 518256-11 Write Cycle 2 (CE Controlled) (4) t WC ADDRESS CE t AS t CW (6) t WR (2) t AW WE OUTPUT Hi-Z INPUT t DW t DH (5) 518256-12 NOTES: 1. The internal write time of the memory is defined by the overlap of CE active and WE low. Both signals must be active to initiate and any one signal can terminate a write by going inactive. The data input setup and hold timing should be referenced to the second transition edge of the signal that terminates the write. 2. t WR is measured from the earlier of CE or WE going HIGH. 3. During this period, I/O pins are in the output state so that the input signals of opposite phase to the outputs must not be applied. 4. OE = V IL or V IH. However it is recommended to keep OE at V IH during write cycle to avoid bus contention. 5. If CE is LOW during this period, I/O pins are in the output state. Then the data input signals of opposite phase to the outputs must not be applied to them. 6. t CW is measured from CE going LOW to the end of write. 8
Package Diagrams 28-pin 600 mil Plastic DIP 15 MAX INDEX 0.543 ±0.010 [13.79 ±0.254] 0.600 [15.24] TYP 0.062 [1.57] MAX 1.470 +0.008 0.012 37.33 +0.203 0.305 0.039 +0.020 0.022 0.991 +0.508 0.559 0.010 ±0.002 [0.254 ± 0.51] 0.195 [4.95] MAX 0.118 [3.00] MIN Units in inches [mm] 0.100 [2.54] TYP. 0.060 +0.020 0.022 0.152 +0.508 0.559 0.018 ±0.003 [0.457 ±0.076] 0.020 [0.508] MIN 28-pin 330 mil SOP Units in inches [mm] 0.339 ± 0.008 [8.61 ± 0.203] 0.465 ± 0.012 [11.81 ± 0.305] 0.402 ±0.012 [10.21 ± 0.203] 0 MIN (STAND OFF) INDEX 0.031 ± 0.008 [0.787 ± 0.203] 0.713 [18.11] TYP 0.006 ± 0.002 [0.152 ± 0.051] 0.112 [0.285] MAX "A" 0.098 ± 0.005 [2.49 ± 0.127] 0.008 [0.203] 0.050 [1.27] TYP 0.018 ± 0.004 [0.457 ± 0.102] 0.024 [0.610] View "A" 0.008 [0.203] MAX 0.027 [0.686] MAX 9
Package Diagrams (Cont d) 28-Pin TSOP Unit in inches [mm] 0.463 ±0.003 [11.76 ± 0.076] 0.528 ±0.008 [13.41 ± 0.203] 0.046 ±0.004 [1.17 ± 0.102] 0.315 ±0.004 [8.00 ± 0.102] 0.020 +0.007 0.008 0.508 +0.178 0.305 0.006 ±0.002 [0.152 ± 0.051] 0.022 [0.559] BSC 0.006 ±0.004 [0.152 ± 0.102] 10
11
WORLDWIDE OFFICES U.S.A. 3910 NORTH FIRST STREET SAN JOSE, CA 95134 PHONE: 408-433-6000 FAX: 408-433-0185 HONG KONG 19 DAI FU STREET TAIPO INDUSTRIAL ESTATE TAIPO, NT, HONG KONG PHONE: 852-2665-4883 FAX: 852-2664-7535 TAIWAN 7F, NO. 102 MIN-CHUAN E. ROAD, SEC. 3 TAIPEI PHONE: 886-2-2545-1213 FAX: 886-2-2545-1209 1 CREATION ROAD I SCIENCE BASED IND. PARK HSIN CHU, TAIWAN, R.O.C. PHONE: 886-3-578-3344 FAX: 886-3-579-2838 SINGAPORE 10 ANSON ROAD #23-13 INTERNATIONAL PLAZA SINGAPORE 079903 PHONE: 65-3231801 FAX: 65-3237013 JAPAN WBG MARINE WEST 25F 6, NAKASE 2-CHOME MIHAMA-KU, CHIBA-SHI CHIBA 261-71 PHONE: 81-43-299-6000 FAX: 81-43-299-6555 IRELAND & UK BLOCK A UNIT 2 BROOMFIELD BUSINESS PARK MALAHIDE CO. DUBLIN, IRELAND PHONE: +353 1 8038020 FAX: +353 1 8038049 GERMANY (CONTINENTAL EUROPE & ISRAEL ) 71083 HERRENBERG BENZSTR. 32 GERMANY PHONE: +49 7032 2796-0 FAX: +49 7032 2796 22 U.S. SALES OFFICES NORTHWESTERN 3910 NORTH FIRST STREET SAN JOSE, CA 95134 PHONE: 408-433-6000 FAX: 408-433-0185 NORTHEASTERN SUITE 436 20 TRAFALGAR SQUARE NASHUA, NH 03063 PHONE: 603-889-4393 FAX: 603-889-9347 SOUTHWESTERN SUITE 200 5150 E. PACIFIC COAST HWY. LONG BEACH, CA 90804 PHONE: 562-498-3314 FAX: 562-597-2174 CENTRAL & SOUTHEASTERN 604 FIELDWOOD CIRCLE RICHARDSON, TX 75081 PHONE: 972-690-1402 FAX: 972-690-0341 Copyright 1998, MOSEL VITELIC Inc. 11/98 Printed in U.S.A. The information in this document is subject to change without notice. MOSEL VITELIC makes no commitment to update or keep current the information contained in this document. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of MOSEL-VITELIC. MOSEL VITELIC subjects its products to normal quality control sampling techniques which are intended to provide an assurance of high quality products suitable for usual commercial applications. MOSEL VITELIC does not do testing appropriate to provide 100% product quality assurance and does not assume any liability for consequential or incidental arising from any use of its products. If such products are to be used in applications in which personal injury might occur from failure, purchaser must do its own quality assurance testing appropriate to such applications. MOSEL VITELIC 3910 N. First Street, San Jose, CA 95134-1501 Ph: (408) 433-6000 Fax: (408) 433-0952 Tlx: 371-9461