CATALINA PLAY SYSTEM P280060

CATALINA PLAY SYSTEM P280060 INSTALLATION AND OPERATING INSTRUCTIONS 16'-6" 54" 48" 16'-0" WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer to these instructions often and give them to any future owner of this play system. Manufacturer contact information provided below. OBSTACLE FREE SAFETY ZONE - 16 6 x 16 (7.62 m x 7.92 m) area requires Protective Surfacing. See page 3. CAPACITY - 5 Users Maximum, Ages 2 and up. RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks. PLAY STRUCTURE SET-UP WITH USER ZONE DIMENSIONS: 16 6 x 16 4-8 Hrs Two person assembly Prior to assembly, you MUST read the Owner s Manual for important safety warnings and details on installing a shock absorbing surface. This unit is intended for a maximum of 5 users, ages 2 to 10 (50kg. per child). Solowave Design 375 Sligo Rd. West, PO Box 10 Mount Forest, ON Canada N0G 2L1 General Inquiries: 8:00am - 4:30pm EST Toll Free: 1-877-966-3738 support@solowavedesign.com Table of Contents Warnings and Safe Play Instructions............... pg. 2 Protective Surfacing Guidelines................... pg. 3 Instructions for Proper Maintenance............... pg. 4 About Our Wood Limited Warranty.............. pg. 5 Keys to Assembly Success...................... pg. 6 Metric Conversion Sheets..................... pg. 7,8 Part ID....................................... pg. 9 Installation of I.D./Warning Plaque............Final Step 9400060 Rev 02/27/2013

Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they understand and follow them. Remember on-site adult supervision is required for children of all ages. SERIOUS HEAD INJURY HAZARD Installation over concrete, asphalt, dirt, grass, carpet and other hard surface creates a risk of serious injury or death from falls to the ground. Install and maintain shock absorbing material under and around play-set as recommended on page 3 of these instructions. COLLISION HAZARD Place play-set on level ground at least 6 feet from any obstruction such as a garage or house, fences, poles, trees, sidewalks, walls, landscape timbers, rocks, pavement, planters, garden borders, overhanging branches, laundry lines, and electrical wires. (See OBSTACLE FREE SAFETY ZONE on cover) CHOKING HAZARD/SHARP EDGES & POINTS Adult Prior to assembly assembly, required. this product This product contains contains small parts. small parts and DO NOT parts allow with children sharp edges less and than points. 5 years Keep of age parts near away or from around children loose nuts, until fully screws, assembled. washers, plastic bags and other small parts. WARNING LABEL Owners shall be responsible for maintaining the legibility of the warning labels. WARNING STRANGULATION HAZARD NEVER allow children to play with ropes, clotheslines, pet leashes, cables, chains or cord-like items when using this play-set or to attach these items to play-set. NEVER allow children to wear loose fitting clothing, ponchos, hoods, scarves, capes, necklaces, items with draw-strings, cords or ties when using this play-set. NEVER allow children to wear bike or sport helmets when using this play-set. Failure to prohibit these items, even helmets with chin straps, increases the risk of serious injury and death to children from entanglement and strangulation. TIP OVER HAZARD Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose-fill surfacing materials washing away during heavy rains. DO NOT allow children to play on the play-set until the assembly is complete and the unit is properly anchored. WARNING Safe Play Instructions Observe capacity limitations of your play-set. See front cover. Dress children with well fitting and full foot enclosing footwear. Teach children to sit with their full weight in the center of the swing seat to prevent erratic swing motion or falling off. Check for splintered, broken or cracked wood; missing, loose, or sharp edged hardware. Replace, tighten and or sand smooth as required prior to playing. Verify that suspended climbing ropes, rope ladders, chain or cable are secured at both ends and cannot be looped back on itself as to create an entanglement hazard. On sunny and or hot days, check the slide and other plastic rides to assure that they are not very hot as to cause burns. Cool hot slide and rides with water and wipe dry prior to using. Do not allow children to wear open toe or heel footwear like sandals, flip flops or clogs. Do not allow children to walk, in front, between, behind or close to moving rides. Do not let children twist swing chains or ropes or loop them over the top support bar. This may reduce the strength of the chain or rope and cause premature failure. Do not let children get off rides while they are in motion. Do not permit climbing on equipment when it is wet. Do not permit rough play or use of equipment in a manner for which it was not intended. Standing on or jumping from the roof, elevated platforms, swings, climbers, ladders or slide can be dangerous. Do not allow children to swing empty rides or seats. Do not allow children to go down slide head first or run up slide. 2 support@solowavedesign.com

3 support@solowavedesign.com

4 support@solowavedesign.com

5 support@solowavedesign.com

Tools Required Keys to Assembly Success Shovel Measuring Drill (1/8 Safety Hammer Ratchet 1/2, Level #2 & #3 Phillips Tape 3/16 Bit) Glasses 7/16 & 9/16 or Robertson Square Ruler Step Ladder Part Identification Key On each page, you will find the parts and quantities required to complete the assembly step illustrated on that page. Here is a sample. 2X 1234 Post 2 x 4 x 83 Symbols Throughout these instructions symbols are provided as important reminders for proper and safe assembly. This identifies information that requires special attention. Improper assembly could lead to an unsafe or dangerous condition. Use Help Measure Distance Use Help Where this is shown, 2 or 3 people are required to safely complete the step. To avoid injury or damage to the assembly make sure to get help! Check that assembly is square before tightening bolts. Use a measuring tape to assure proper location. Square Assembly Check that set or assembly is properly level before proceeding. Pre-drill 1/8 Bit Pre-drill a pilot hole before fastening screw or lag to prevent splitting of wood. This indicates time to tighten bolts, but not too tight! Do not crush the wood. This may create splinters and cause structural damage. Use Level Tighten Bolts CAUTION Protrusion Hazard Once the assembly is tightened, watch for exposed threads. If a thread protrudes from the T-Nut, remove the bolt and add washers to eliminate this condition. Extra washers have been provided for this purpose. Proper Assembly Lag screws require drilling pilot holes to avoid splitting wood. Only a flat washer is required. For ease of installation liquid soap can be used on all lag-type screws. For bolts, tap T-Nut into hole with hammer. Insert the hex bolt through lock washer first then flat washer then hole. Because the assemblies need to be squared do not completely tighten until instructed. Pay close attention to diameter of the bolts. 5/16 is slightly larger than 1/4. No Yes 6 support@solowavedesign.com

SOLO)WAVE DESIGN HARDWARE 5/16"(.31) = 8mm Hex Bolt 5/16" (8mm) Lock Washer 1/4"(0.25) = 6mm Hex Bolt 1/4"(0.25) = 6mm Lag Screw 1/4" (6mm) Flat Washer 5/16" (8mm) Flat Washer 1/4" (6mm) Lock Washer 1/4" (6mm) Flat Washer 5/16" (8mm) T-Nut 1/4" (6mm) T-Nut HARDWARE LENGTH CHART inches vs millimetres 6 152 5½ 140 5 127 4½ 114 4 102 3½ 89 3 76 2½ 64 2 51 1½ 38 1¼ 32 1-1/8 29 1 25.4 7/8 22 3/4 19 1/2 12.7 DIAMETER CONVERSION 5/16"(.31) = 8mm Lag Screw 3/8"(.38) = 9.5mm Lag Screw 5/16" (8mm) Flat Washer For example: 1 inch = 25.4mm BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm LENGTH CONVERSION 1 inch = 25.4mm 3/8" (9.5mm) Flat Washer For example: BOLT LENGTH 4½ (4.5) inches long 4.5 inches x 25.4mm = 114mm long 7 support@solowavedesign.com

1" SOLO)WAVE DESIGN WOOD PROFILES 25.4 1" 25.4 1" 63.5 2 1/2" 5/4 x 3 88.9 3 1/2" 5/4 x 4 114.3 4 1/2" 5/4 x 5 34.9 1 3/8" 38.1 1 1/2" 2 x 2 63.5 2 1/2" 25.4 2 x 3 38.1 1 1/2" 11.1.44 15.9 5/8" 15.9 5/8" 82.6 3 1/4" 34.9 1 3/8" 60.3 2 3/8" 15.9 85.7 5/8" 3 3/8" 1/2 x 4 1 x 2 1 x 3 1 x 4 25.4 1" 139.7 5 1/2" 5/4 x 6 34.9 1 3/8" 85.7 3 3/8" 2 x 4 15.9 5/8" 114.3 4 1/2" 1 x 5 88.9 3 1/2" 88.9 3 1/2" 4 x 4 38.1 1 1/2" 136.5 5 3/8" 2 x 6 Dimensions in brackets [mm] represent millimetres. 15.9 5/8" 136.5 5 3/8" LENGTH CONVERSION 1 inch = 25.4mm 1 x 6 For example: BOARD LENGTH 59¼ (59.25) inches 59.25 inches x 25.4mm = 1505mm 8 support@solowavedesign.com

Part Identification (Reduced Size) (3) 0125 Joint Strip 7 x 40 x 1215mm 38012536 (20) 5155 Cedar Roofing 9.52 x 88.9 x 1206.5mm 3635155 (2) 0302 Trim Short 10 x 43 x 680mm 38030236 (2) 0227 Trim Corner 10 x 50 x 1215mm 38022736 (4) 0124 Corner Trim 10 x 50 x 1215mm 38012436 (2) 0219 Side Soffit 15 x 45 x 1195mm 38021936 (4) 0305 Fascia 15 x 50 x 870mm 38030536 (2) 0142 Soffit 15 x 90 x 1118mm 38014236 (1) 8073 Dormer Bottom 15.9 x 34.9 x 558.8mm 3638073 (2) 8072 Dormer Side Bursts 15.9 x 57.2 x 171.5mm 3638072 (1) 8071 Dormer Centre 15.9 x 57.2 x 273.1mm (1) 8074 Dormer Burst 15.9 x 85.7 x 139.7mm 3638074 3638071 (2) 8070 Dormer Side 15.9 x 57.2 x 346mm 3638070 (2) 0303 Window Board 15.9 x 136.5 x 533.4mm 38030336 (2) 0134 Short Wall Connector 21 x 30 x 610mm 38013436 (3) 0138 Connector 21 x 30 x 1118mm 38013836 (2) 8102 Bench Gusset 23.8 x 82.6 x 249.2mm 3638102 (4) 8103 Bench Leg 23.8 x 82.6 x 450.9mm 3638103 9 support@solowavedesign.com

Part Identification (Reduced Size) (2) 8100 Bench Top 23.8 x 108 x 762mm 3638100 (1) 0309 Lower Cafe 25.4 x 88.9 x 1118mm 38030936 (1) 0304 Table Top 25.4 x 114.3 x 1054.1mm 38030436 (1) 0306 Angle Table Top 25.4 x 114.3 x 1054.1mm 38030636 (2) 0318 Ground Stake 31.8 x 38.1 x 355.6mm 3640318 (2) 0301 Spacer 31.8 x 31.8 x 420mm 38030136 (1) 0308 Top Wall 31.8 x 136.5 x1118mm 38030836 (2) 0311 Short Table Support 34.9 x 57.2 x 85.7mm 38031136 (2) 0307 Long Table Support 34.9 x 85.7 x 101.6mm 38030736 (1) 8069 Dormer Cleat 34.9 x 85.7 x 254mm 3638069 (2) 8120 Seat Support 38.1 x 38.1 x 260.4mm 3638120 (2) 8104 Bench Support 38.1 x 38.1 x 376.2mm 3638104 (6) 0310 Roof Rafter 38.1 x 38.1 x 845mm 38031036 10 support@solowavedesign.com

Part Identification (Reduced Part Size) (2) 0180 38018036 Window Wall Assembly (3) 0181 38018136 Wall Assembly (1) 0184 38018436 Door Frame Assembly (1) 0287 38028775 Door Panel Assembly (1) 3323694 Door Window w/ Hadrware (1) 0280 38028036 Half Wall Assembly (4) 3460 3603460 Shutter (1) 8068 3638068 Dormer Roof Set (Left/Right Dormer) (2) 3323693 Large Window A w/ (1) 3327521 (2Pk) Peak Detail (2) 9201700 Door Handle w/ Screws (1) 9201553 (2 Pk) Dormer Bracket (Only 1 Required) (1) 9757510 Cafe Canopy (1) 9200875 Cafe Frame (2) 9201710 Door Hinge w/ Screws (1) 3750060 Cafe Canopy Set (1) 3327501 Flower Box (1) 9201621 Door Latch w/ Screws (2) 9201100 Corner Brace w/ Screws 11 support@solowavedesign.com

Identification (Actual Size) 8pc. LW1-1/4" Lock Washer - (9253200) 3pc. FW3 - #8 Flat Washer - (9251500) 26pc. FW1-1/4" Flat Washer - (9251200) 60pc. S0 - Truss Screw #8 x 7/8" - (9229505) 8pc. TN1-1/4" T - Nut -(9285200) 42pc. TS - Trim Screw No.6 x 30mm- (9224911) 11pc. S5 - Pan Screw #8 x 1/2" - (9264504) 16pc. S8 - Pan Screw #12 x 3/4" - (9264603) 8pc. H3 - Hex Bolt 1/4 x 2-1/2" - (9277222) 4pc. S6 - Pan Screw #12 x 1" - (9264610) 23pc. S26 - Pan Screw #8 x 2" - (9224520) 14pc. S1 - Wood Screw #8 x 1-1/8" - (9290514) 84pc. S2 - Wood Screw #8 x 1-1/2" - (9260512) 22pc. S15 - Wood Screw #8 x 1-3/4" - (9260513) 21pc. S3 - Wood Screw #8 x 2-1/2" - (9290522) 12 support@solowavedesign.com

5155 20 X 2 X 8068 8071 4 X 0305 8070 2 X 2 X Peak Detail 8072 2 X 8074 2 X 0219 8073 Cafe Canopy Set 2 X 0303 3 X 0181 0306 3460 4 X 0304 Large Window A 2 X 2 X 0301 Flower Box 2 X 0307 0134 2 X 2 X 0280 0318 Door Window Door Handle 2 X Window Wall Assembly 2 X Door Hinge 2 X 2 X 0302 0124 4 X 13 support@solowavedesign.com

8069 Dormer Bracket 6 X 0310 0184 0308 0142 2 X Corner Brace 2 X 0311 2 X 0309 2 X 0227 3 X 0125 3 X 0138 0287 Door Latch 2 X 8100 2 X 8102 2 X 8120 4 X 8103 8104 2 X 14 support@solowavedesign.com

Step 1: Inventory Parts - Read This Before Starting Assembly STOP STOP STOP STOP A. This is the time for you to inventory all your hardware, wood and accessories, referencing the parts identification sheets. This will assist you with your assembly. The wood pieces will have the four digit key number stamped on the ends of the boards. The wood pieces are referenced throughout the instructions with this number. Please refer to Page 6 for proper hardware assembly. Each step indicates which bolts and/or screws you will need for assembly, as well as any flat washers, lock washers, t-nuts or lock nuts. B. If there are any missing or damaged pieces or you need assistance with assembly please contact the Consumer Relations Department directly. Call us before going back to the store. 1-877-966-3738 support@solowavedesign.com C. Read the assembly manual completely, paying special attention to ANSI warnings; notes; and safety/maintenance information on pages 1-6. D. Before you discard your cartons fill out the form below. The carton I.D. stamp is located on the end of each carton. The tracking number is located on the Big Backyard ID Plaque (3320356). Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department. MODEL NUMBER: P280060 CARTON I.D. STAMP: 14459 (Box 1) CARTON I.D. STAMP: 14459 (Box 2) CARTON I.D. STAMP: 14459 (Box 3) CARTON I.D. STAMP: 14459 (Box 4) CARTON I.D. STAMP: 14459 (Box 5) CARTON I.D. STAMP: 14459 (Box 6) TRACKING NUMBER (from ID Plaque): 15 support@solowavedesign.com

Step 2: Front Wall Assembly Part 1 A: Using a 1/8 drill bit pre-drill the 3 pilot holes in the (0180) Window Wall Assembly, as shown in fig. 2.1. Be sure to drill at an angle. Drill at angle to clear this edge. Fig. 2.1 0180 Please Note: Wall Panels are permanently assembled and 100% inspected at the factory. With rough handling and movement during transit, the assembly may shift causing an occasional sharp staple point or crown to protrude. Please check panels prior to assembly and remove any sharp points or hammer in protruding staple crowns. 1x 0180 Wood Parts Window Wall Assembly 559 x 1220 mm 16 support@solowavedesign.com

Step 2: Front Wall Assembly Part 2 B: Lay (0180) Window Wall Assembly from Part 1 and (0184) Door Frame Assembly on the ground next to each other and attach through the prevously pre-drilled holes with 3 (S26) #8 x 2 Pan Screws. The top screw must be installed by hand, the remaining 2 screws can be installed by a power drill. (fig. 2.2) C: Place 1 (0138) Connector to the top of the assembly and 1 (0138) Connector to the bottom of the assembly, pre-drill pilot holes with a 1/8 drill bit, then attach with 4 (S2) #8 x 1-1/2 Wood Screws per board. (fig. 2.3) Drive this screw by hand Power Drive these screws S26 x 3 Fig. 2.2 0184 Bottom Top Pre-Drill Window Walls 0180 Fig. 2.3 Connector 0138 S2 x 4 S2 x 4 0180 To prevent splitting of wood, drill 1/8 pilot holes using predrilled holes as a guide for all S2 screws. Wood Parts 2 x Connector 21 x 30 x 1118 mm 0138 1 x 0184 Door Frame Assembly 559 x 1220 mm 8 x S2 #8 x 1-1/2 Wood Screw 3 x S26 #8 x 2 Pan Screws 17 support@solowavedesign.com

Step 3: Side Wall Assembly A: Lay 2 (0181) Wall Assembly next to each other and 1 next to (0180) Window Wall Assembly, using a 1/8 drill bit pre-drill the 3 pilot holes in 2 (0181) Wall Assemblies. Be sure to drill at an angle. (fig. 3.1 and 3.2) B: Attach Wall Assemblies together through the prevously pre-drilled holes with 3 (S26) #8 x 2 Pan Screws per wall. The top screw must be installed by hand, the remaining 2 screws can be installed by a power drill. (fig. 3.1 and 3.2) C: Place 1 (0138) Connector to the top of the Back Wall assembly and 1 (0134) Short Wall Connector to the bottom of both the Back Wall and Right Side Wall assemblies, pre-drill pilot holes with a 1/8 drill bit, then attach with 4 (S2) #8 x 1-1/2 Wood Screws per board. (fig. 3.3 and 3.4) Fig. 3.1 0181 Fig. 4.1 0181 Fig. 3.2 0180 Pre-Drill S26 x3 S26 x3 Back Wall Right Side Wall Fig. 3.3 S2 x 4 0138 Fig. 3.4 0181 0181 0180 0134 S2 x 4 0134 S2 x 4 Wood Parts 1 x 0138 Connector 21 x 30 x 1118 mm 2 x 0134 Short Wall Connector 21 x 30 x 610 mm 3 x 0181 Wall Assembly 559 x 1220 mm 1 x 0180 Window Wall Assembly 559 x 1220 mm 12 x S2 #8 x 1-1/2 Wood Screw S26 6 x #8 x 2 Pan Screws 18 support@solowavedesign.com

Step 4: Place Wall Assemblies A: With 2 adult helpers, stand the wall assemblies as shown in fig. 4.1. Fig. 4.1 Top View Side wall edge flush with siding Side wall edge flush with siding Back Wall Assembly (from Step 3) 0280 Half Wall Assembly Right Wall Assembly (from Step 3) Front Wall Assembly (from Step 2) Side wall edge flush with Door Frame Side wall edge flush with siding Wood Parts 1 x 0280 Half Wall Assembly 570 x 1118 mm 19 support@solowavedesign.com

Step 5: Wall Assembly Make sure the ground is level and the playhouse walls are square. Note: Pre-drill all holes using a 1/8 drill bit before installing the Pan screws. A: Attach the Right Wall Assembly to the Front Wall and Back Wall Assemblies with 3 (S26) #8 x 2 Pan Screws per side. (fig. 5.1 and 5.2) B: Attach the (0280) Half Wall Assembly to the Front Wall and Back Wall Assemblies with 2 (S26) #8 x 2 Pan Screws per side. (fig. 5.1 and 5.2) Right Wall Assembly Fig. 5.1 25.4 mm Half Wall Assembly S26 S26 Front Wall Assembly Fig. 5.2 Back Wall Assembly Half Wall Assembly Right Wall Assembly S26 S26 10 x S26 #8 x 2 Pan Screw 20 support@solowavedesign.com

Step 6: Half Wall Assembly A: Place (0309) Lower Cafe tight to the top of the Half Wall Assembly and attach to Front and Back Wall Assemblies with 4 (S26) #8 x 2 Pan Screws. (fig. 6.1) B: Attach 2 (0307) Long Table Supports to the front of and flush to top of (0309) Lower Cafe in the outside holes with 2 (S3) #8 x 2-1/2 Wood Screws per support. (fig. 6.1 and 6.2) C: Attach 2 (0311) Short Table Supports to the back of and flush to top of (0309) Lower Cafe in the inside holes with 2 (S3) #8 x 2-1/2 Wood Screws per support. (fig. 6.1 and 6.2) D: Tight to the top of (0309) Lower Cafe attach 1 (0301) Spacer to each end with 3 (S15) #8 x 1-3/4 Wood Screws per spacer. (fig. 6.1) E: Tight to the top of each (0301) Spacer attach (0308) Top Wall to the Front and Back Wall Assemblies with 4 (S3) #8 x 2-1/2 Wood Screws. (fig. 6.1) Fig. 6.2 0304 Fig. 6.1 Back Wall Assembly 0308 0311 0301 0309 x 4 S3 3-1/4 x 6 S15 x 4 0307 S26 0311 Flush S3 x 2 per support 0307 0301 Front Wall Assembly Half Wall Assembly Wood Parts 2 x 0311 Short Table Support 34.9 x 57.2 x 85.7 mm 2 x 0307 Long Table Support 34.9 x 85.7 x 101.6 mm 2 x 0301 Spacer 31.8 x 31.8 x 420 mm 1 x 0309 Lower Cafe 25.4 x 88.9 x 1118 mm 1 x 0308 Top wall 31.8 x 136.5 x 1118 mm 6 x S15 #8 x 1-3/4 Wood Screw 4 x S26 #8 x 2 Pan Screw 12 x S3 #8 x 2-1/2 Wood Screw 21 support@solowavedesign.com

Step 7: Cafe Table Assembly Part 1 A: Place (0304) Table Top over (0311) Short Table Supports and (0306) Angle Table Top over (0307) Long Table Support and attach with 4 (S15) #8 x 1-3/4 Wood Screws per board. (0304) Table Top should overhang (0311) Short Table Support by 1/4 as shown in fig. 7.1 and 7.7. B: Tight to top of (0304) Table Top attach 1 (0303) Window Board flush to the outside edge of each (0301) Spacer and to (0308) Top Wall with 5 (S2) #8 x 1-1/2 Wood Screws per board, as shown in fig. 7.2. C: Secure each (0303) Window Board to (0304) Table Top with 1 Corner Brace per board using 3 (S5) #8 x 1/2 Pan Screws per brace. (fig. 7.3 and 7.4) 0304 Fig. 7.1 0311 (hidden under boards) 0304 Fig. 7.7 0306 0311 0307 (hidden under boards) S15 x 8 1/4 overhang Corner Brace Fig. 7.2 0303 Fig. 7.4 S5 x 3 per brace S2 S2 x 5 0308 Fig. 7.3 0301 S2 x 5 0308 0304 0303 0303 0301 0304 Wood Parts 1 x 0304 Table Top 25.4 x 114.3 x 1054.1 mm 1 x 0306 Angle Table Top 25.4 x 114.3 x 1054.1 mm 2 x 0303 Window Board 15.9 x 136.5 x 533.4 mm 10 x S2 #8 x 1-1/2 Wood Screw 6 x S5 #8 x 1/2 Pan Screw 8 x #8 x 1-3/4 Wood Screw S15 Other Parts 2 x Corner Brace 22 support@solowavedesign.com

Step 7: Cafe Table Assembly Part 2 D: Feed Cafe Frame through Cafe Canopy then place Cafe Frame flush to the bottom of (0308) Top Wall and secure with 1 (S6) #12 x 1 Pan Screw per end. (fig. 7.5 and 7.6) E: Attach Cafe Canopy to the front face of (0308) Top Wall with 3 (S5) #8 x 1/2 Pan Screws (with #8 flat washer), as shown in fig. 7.5. The edge of the canopy should lay on top of (0308) Top Wall. Fig. 7.5 Screw to front face of Top Wall Fig. 7.6 S6 0308 Cafe Canopy Set S5 (with #8 flat washers) 3 x S5 #8 x 1/2 Pan Screw (#8 flat washer) 2 x S6 #12 x 1 Pan Screw Other Parts 1 x Cafe Canopy Set 23 support@solowavedesign.com

Step 8: Soffit Assembly Make sure the playhouse walls are square before proceeding. Note: Pre-drill all holes using a 1/8 drill bit before installing the wood screws. A: Flush to the inside of the (0138) Connectors attach 1 (0142) Soffit to the Front Wall Assembly and 1 to the Back Wall Assembly with 6 (S2) #8 x 1-1/2 Wood Screws per board. Notice the hole orientation of each board. (fig. 8.1) B: Flush to the outside edges of the (0142) Soffit, attach 1 (0219) Side Soffit to (0308) Top Wall and 1 to Right Wall Assembly with 4 (S2) #8 x 1-1/2 Wood Screws per board. Notice the hole orientation of each board and notice that the end holes are not used. (fig. 8.2) Fig. 8.1 Hole not used in this step 0142 Flush S2 x 6 S2 x 6 0142 0138 Hole not used in this step Fig. 8.2 Front Wall Assembly S2 x 4 Flush 0142 0219 Right Wall Assembly Note Hole Orientation Flush 0219 S2 x 4 0308 End holes not used Wood Parts 2 x 0219 Side Soffit 15 x 45 x 1195 mm 2 x 0142 Soffit 15 x 90 x 1118 mm 20 x S2 #8 x 1-1/2 Wood Screw 24 support@solowavedesign.com

Step 9: Roof Assembly Part 1 A: Attach 1 (0310) Roof Rafter to another at the peak using 1 (S3) #8 x 2-1/2 Wood Screw. Do this three times so you have 3 Roof Rafter Assemblies. (fig. 9.1) B: Attach 1 Peak Detail to 2 of the Roof Rafter Assemblies using 16 (S8) #12 x 3/4 Pan Screw (with 1/4 flat washer). (fig. 9.2) C: Place each Roof Rafter Assembly flush to the outside edges of (0219) Side Soffit and (0142) Soffit and attach using 2 (S2) #8 x 1-1/2 Wood Screws per Roof Rafter Assembly, as shown in fig. 9.3 and 9.4. Notice the orientation of the Peak Detail on each end. S3 Fig. 9.1 Fig. 9.2 0310 0310 0310 0310 1/4 flat washer x 8 per peak Assemble 3 sets of Roof Rafters 0219 0142 0219 Peak Detail S8 x 8 per peak Fig. 9.3 0142 0310 0219 Fig. 9.4 0142 0219 S2 x 3 per side Wood Parts 6 x 0310 Roof Rafter 38.1 x 38.1 x 845 mm 6 x S2 #8 x 1-1/2 Wood Screw 16 x S8 #12 x 3/4 Pan Screw (with 1/4 flat washer) 3 x S3 #8 x 2-1/2 Wood Screw Other Parts 2 x Peak Detail 25 support@solowavedesign.com

Step 9: Roof Assembly Part 2 D: Starting at the top of the Roof Rafter Assembly attach 1 (5155) Cedar Roofing on each side of the (0310) Roof Rafters with 3 (S0) #8 x 7/8 Truss Screws per board. (fig. 9.5 and 9.6) Be sure to overlap the top of the boards so there are no gaps. E: Attach 1 (5155) Cedar Roofing at the bottom of the Roof Rafter Assembly on each side, making sure they are flush to each end (0310) Roof Rafter with 3 (S0) #8 x 7/8 Truss Screws per board. (fig. 9.7) F: On each side of the assembly evenly space and attach 8 more (5155) Cedar Roofing, leaving no gaps, with 3 (S0) #8 x 7/8 Truss Screws per board. There should be 10 (5155) Cedar Roofing on both sides. (fig. 9.7) S0 x 3 per board Fig. 9.5 Fig. 9.6 0310 5155 x 27 (3 per board) S0 5155 x 9 per side Roof Rafter Assemblies Flush to inside groove Fig. 9.7 Flush to inside groove Wood Parts 20 x 5155 Cedar Roofing 9.52 x 88.9 x 1206.5 mm 60 x S0 #8 x 7/8 Truss Screw 26 support@solowavedesign.com

Step 9: Roof Assembly Part 3 G: Attach 2 (0305) Fascia to both end Roof Rafter Assemblies, so the peaks are tight together, using 3 (S2) #8 x 1-1/2 Wood Screws per (0305) Fascia. (fig. 9.8) Align vertical edges 0305 Fig. 9.8 S2 x 6 S2 x 6 0305 Wood Parts 4 x 0305 Fascia 15 x 50 x 870 mm 12 x S2 #8 x 1-1/2 Wood Screw 27 support@solowavedesign.com

Step 10: Attach Corner and Joint Trim A: Tight to the bottom of (0142) Soffit on the Front and Back Wall Assemblies and tight to bottom of (0219) Side Soffit on the Right Wall Assembly attach 1 (0125) Joint Strip per wall using 4 (TS) #6 x 30mm Trim Screws per board, as shown in fig. 10.1, 10.2 and 10.5. B: Flush to the wall edges and tight to (0142) Soffit attach 2 (0124) Corner Trim to both the Front and Back Wall Assemblies with 3 (TS) #6 x 30mm Trim Screws per board, as shown in fig. 10.1 and 10.3. Make sure the holes are located closer to the corner. C: Attach 2 (0302) Trim Short to the Half Wall Assembly so they are flush to the outside edge of (0124) Corner Trim and tight to bottom of (0303) Window Boards using 3 (TS) #6 x 30mm Trim Screws per board, as shown in fig. 10.1, 10.2 and 10.3. Make sure the holes are located closer to the corner. D: Attach 2 (0227) Trim Corner to the Right Wall Assembly so they are flush to the outside edge of (0124) Corner Trim and tight to bottom of (0219) Side Soffit using 6 (TS) #6 x 30mm Trim Screws per board, as shown in fig. 10.2. Make sure the holes are located closer to the corner. Fig. 10.1 0142 Fig. 10.3 Flush TS x 3 per board 0303 Fig. 10.4 0124 TS x 2 per board 0302 Flush Note: Make sure no screws protrude. 0124 0302 Half Wall Assembly 0302 Fig. 10.2 0124 0125 0219 0125 Front Wall Assembly 0124 0142 Fig. 10.5 TS Flush x 6 per board 0219 0227 0124 x 4 per board TS 0125 Right Wall Assembly 0227 0124 0125 Back Wall Assembly Wood Parts 4 x 0124 Corner Trim 10 x 50 x 1215 mm 2 x 0302 Trim Short 10 x 43 x 680 mm 2 x 0227 Trim Corner 10 x 50 x 1215 mm 3 x 0125 Joint Strip 7 x 40 x 1215 mm 42 x TS #6 x 30 mm Trim Screw 28 support@solowavedesign.com

Step 11: Door Assembly A: Attach 2 Door Hinges on the outside of the (0287) Door Panel Assembly. Judge spacing based on fig. 11.1. Use provided hardware for hinges. (fig. 11.1 and 11.2) B: Attach Door Hinges to (0184) Door Frame Assembly using provided hardware as shown in fig. 11.1 and 11.2. Make sure equal spacing at top and bottom when attaching. C: On the opposite side of the hinges on (0287) Door Panel Assembly attach 1 Door Handle using hardware provided as shown in fig. 11.1 and 11.3. D: On the front of (0287) Door Panel Assembly attach a second Door Handle using hardware provided as shown in fig. 11.4 and 11.5. E: Under the Door Handle attach 2 Door Latches using the hardware provided per latch and the Door Latch Bar to the inside of (0184) Door Frame Assembly using the hardware provided as shown in fig. 11.4 and 11.5. Fig. 11.1 0184 Outside Door Handle Fig. 11.2 0184 provided Fig. 11.3 Door Handle Evenly space 0287 Door Hinge provided x 6 per hinge Fig. 11.4 Outside View Fig. 11.5 Inside Door Handle and Door Latch S13 Door Handle Door Latch Bar provided x 2 per latch provided Door Latches Inside View Wood Parts 1 x 0287 Door Panel Assembly Other Parts 1 x Door Latch Bar 2 x Door Latches 2 x Door Handles 2 x Door Hinges (Comes with ) 29 support@solowavedesign.com

Large Window A Step 12: Attach Windows and Flower Box A: Attach 2 Shutter Pivots to 1 (3460) Shutter using the screws provided. Make 4 Shutter Assemblies. (fig. 12.1) B: Attach 2 Shutter Assemblies to 1 Large Window A. Make 2 complete Window/Shutter Assemblies. (fig. 12.2) r Screws C: In the window openings of Right Wall Assembly and Front Wall Assembly insert the Window/Shutter Assemblies from the outside and attach with included hardware per window. (fig. 12.3 and 12.4) D: In the window opening of Door Panel Assembly insert 1 Door Window from the outside and attach with included hardware. (fig. 12.3 and 12.4) Shutter Pivots E: Under the window on the Front Wall Assembly install Flower Box Large with Window 2 (S5) A#8 x 1/2 Pan Screws as shown in fig. 12.3 and 12.5. r Screws Shutter Pivots Shutter Asy Large Window A Fig. 12.1 Shutter Screws Shutter Asy Fig. 12.2 Shutter Screws 3460 Shutter Asy Fig. 12.3 Shutter Asy Included Hardare x 6 per window Fig. 12.4 Fig. 12.5 Front Wall Assembly Right Wall Assembly S5 x 2 Wood Parts 4 x Shutter 15 x 138 x 461 mm 3460 S5 2 x #8 x 1/2 Pan Screw Other Parts 1 x Flower box 2 x Large Window A (with hardware) 1 x Door Window (with hardware) 30 support@solowavedesign.com

Step 13: Attach Ground Stakes A: Drive one (0318) Ground Stake 266.7 mm into the ground at each corner shown in fig. 13.1 and attach with 2 (S3) #8 x 2-1/2 Wood Screws per ground stake. (fig. 13.1 and 13.2) Warning! To prevent tipping and avoid potential injury, stakes must be driven 266.7 mm into ground. Digging or driving stakes can be dangerous if you do not check first for underground wiring, cables or gas lines. S3 Fig. 13.1 0318 Front Wall hidden for clarity Fig. 13.2 S3 266.7 mm Into Ground 0318 0318 Wood Parts 2 x 0318 Ground Stake 38.1 x 38.1 x 355.6 mm 4 x S3 #8 x 2-1/2 Wood Screw 31 support@solowavedesign.com

Step 14: Dormer Assembly Dormer Roof Set - Right Fig. 14.1 Fig. 14.2 Dormer Roof Set - Left Wall angle bracket with 8070 Fig. 14.3 8070 A: Attach 1 Dormer Roof Set Right to 1 Dormer Roof Set Left with 1 Wall Angle Bracket with the hardware provided at the inside peak as shown in (fig. 14.1 and 14. 2). B: Attach 1 (8070) Dormer Side to the inside edge of each Dormer Roof using 2 (S1) #8 x 1-1/8 Wood Screws per board. (fig. 14.3) S1 Fig. 14.4 8070 S1 x 5 8071 8073 8070 C: Attach 1 (8073) Dormer Bottom to the Dormer Assembly with 2 (S1) #8 x 1-1/8 Wood Screws, making sure the top of (8073) Dormer Bottom is tight to the bottom of each (8070) Dormer Side. (fig. 14.4) D: Attach 1 (8071) Dormer Centre, centred and flush to the bottom of (8073) Dormer Bottom with 1 (S1) #8 x 1-1/8 Wood Screw and to the tops of both (8070) Dormer Sides with 2 (S1) #8 x 1-1/8 Wood Screws. (fig. 14.4) Fig. 14.5 8072 S1 8071 Fig. 14.6 8074 8070 8072 8070 E: Place 1 (8072) Dormer Side Burst on each side of the (8071) Dormer Centre so they are tight to the sides and flush to the bottom of (8073) Dormer Bottom and then attach to each (8070) Dormer Side with 1 (S1) #8 x 1-1/8 Wood Screw per board. (fig. 14.5) F: On the outside of the Dormer Assembly and centred on the (8073) Dormer Bottom, attach 1 (8074) Dormer Burst to each (8072) Dormer Side Burst and to (8071) Dormer Centre from the inside of the assembly using 3 (S1) #8 x 1-1/8 Wood Scews. (fig. 14.5 and 14.6) 8073 Wood Parts 2 x 8070 Dormer Side 15.9 x 57.2 x 346mm 1 x 8071 Dormer Centre 15.9 x 57.2 x 273.1mm 2 x 8072 Dormer Side Burst 15.9 x 57.2 x 171.5mm 1 x 8073 Dormer Bottom 15.9 x 34.9 x 558.8mm 1 x 8074 Dormer Burst 15.9 x 85.7 x 139.7mm 14 x S1 #8 x 1-1/8 Wood Screw Other Parts 1 x Wall Angle Bracket (with hardware) 1 x Dormer Roof Set Left 1 x Dormer Roof Set Right 32 support@solowavedesign.com

Step 15: Attach Dormer Assembly to Roof A: On the front side of the playhouse, centred on the 4th (5155) Cedar Roofing from the top, pre-drill 2 pilot holes 1-1/2 (38.1mm) from both sides of the middle (0310) Roof Rafter from the inside of the playhouse as shown in fig. 15.1, 15.2 and 15.3. B: With a helper attach (8069) Dormer Cleat to the outside of the pre-drilled (5155) Cedar Roofing using 2 (S6) #12 x 1 Pan Screws (with 1/4 flat washer). Install from the inside. (fig. 15.1 and 15.3) C: Place the Dormer Assembly from Step 14 over top of the (8069) Dormer Cleat and then fasten with 2 (S3) #8 x 2-1/2 Wood Screws as shown in fig. 15.4. Fig. 15.1 4th Cedar Roofing 5155 8069 0310 Fig. 15.2 4th shingle down, 38.1 mm out from rafter 0310 S6 x 2 with 1/4 flat washer Fig. 15.3 View from inside S3 38.1 mm Dormer Assembly 38.1 mm Fig. 15.4 Wood Parts 1 x 8069 Dormer Cleat 34.9 x 85.7 x 254mm 2 x S3 #8 x 2-1/2 Wood Screw 2 x S6 #12 x 1 Pan Screw (1/4 flat washer) 33 support@solowavedesign.com

Step 16: Bench Assembly Part 1 A: Attach 1 (8120) Seat Support and 1 (8104) Bench Support to 2 (8103) Bench Legs using 2 (H3) 1/4 x 2-1/2 Hex Bolts (with lock washer, flat washer and t-nut) and 2 (S2) #8 x 1-1/2 Wood Screws per board as shown in fig. 16.1. Make sure (8120) Seat Supports are flush with tops of (8103) Bench Legs. B: Create 2 Bench End Assemblies Fig. 16.1 H3 S2 H3 8120 S2 H3 8120 Flush 1/4 lock Washer 1/4 Flat Washer 8104 1/4 T-Nut 8103 8104 8103 2x 4x 2x 8120 8103 8104 Wood Parts Seat Support 38.1 x 38.1 x 260.4mm Bench Leg 23.8 x 82.6 x 450.9mm Bench Support 38.1 x 38.1 x 376.2mm 8 x S2 #8 x 1-1/2 Wood Screw 8 x H3 1/4 x 2-1/2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 34 support@solowavedesign.com

Step 16: Bench Assembly Part 2 C: Centre 1 (8102) Bench Gusset in opening between (8103) Bench Legs on each Bench End Assembly and fasten to (8104) Bench Support with 2 (S2) #8 x 1-1/2 Wood Screws per board. (fig. 16.2) D: Attach 2 (8100) Bench Top to each (8120) Seat Support using 4 (S15) #8 x 1-3/4 Wood Screws per board, as shown in fig. 16.3. The sides of (8100) Bench Top should be flush with the edge of each (8120) Seat Support. The distance between Bench End Assemblies should be 635 mm apart. E: Attach each (8102) Bench Gusset to the (8100) Bench Tops using 2 (S2) #8 x 1-1/2 Wood Screws per board. (fig. 16.4) Fig. 16.2 S2 S15 x 4 per board 8100 8103 8103 8120 8104 8102 8104 635 mm Distance Apart Fig. 16.3 8102 Fig. 16.4 S2 8100 2x 2x 8100 8102 Wood Parts Bench Top 23.8 x 108 x 762mm Bench Gusset 23.8 x 82.6 x 249.2mm 8 x S2 #8 x 1-1/2 Wood Screw 8 x S15 #8 x 1-3/4 Wood Screw 35 support@solowavedesign.com

NOTES 36 support@solowavedesign.com

NOTES 37 support@solowavedesign.com

NOTES 38 support@solowavedesign.com

NOTES 39 support@solowavedesign.com

BIG BACKYARD Consumer Registration Card First Name Initial Last Name Street Apt. No. City State/Province ZIP/Postal Code Country Telephone Number E-Mail Address Model Name Model Number (Box Labels) Serial Number (on ID Plaque) Date Purchase Purchased From How would you rate this product for quality? Excellent Very Good Average Below Average Poor How would you rate this product for ease of assembly? Excellent Very Good Average Below Average Poor How would you rate our instructions? Excellent Very Good Average Below Average Poor How would you rate the quality of packaging? Excellent Very Good Average Below Average Poor Would you recommend the purchase of our products to friends and family? Yes No Comments: MM / DD / YY MAIL TO: Solowave Design TM 375 Sligo Road W. Mount Forest, Ontario, Canada N0G 2L1 Attention: Customer Service Fill out your registration card online at www.bigbackyard.com/ownerslounge Big Backyard would like to say Thank You for your time and feedback. CUT ALONG LINE REVISION: 12/01/09