INSTALLATION AND OPERATING INSTRUCTIONS WARNING

Transcription

1 S K Y L I N E I I P L AY S Y S T E M F INSTALLATION AND OPERATING INSTRUCTIONS WARNING 9.1m To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer to these instructions often and give them to any future owner of this play set. Manufacturer contact information provided below. 5.5m OBSTACLE FREE SAFETY ZONE x 27 area requires Protective Surfacing. See page m 8.3m MAXIMUM VERTICAL FALL HEIGHT CAPACITY - 13 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child. RESIDENTIAL HOME USE ONLY. Not intended for public areas such as multi-unit residences, schools, churches, nurseries, day cares or parks. FORT Hrs Two person assembly TUBE SLIDE 2-4 Hrs Two person assembly Cedar Summit c/o Solowave Design L.P. Mount Forest, ON Canada N0G 2L Rev 09/12/ support@cedarsummitplay.com Customer Service (toll free) Table of Contents Warnings and Safe Play Instructions pg. 2 Protective Surfacing Guidelines pg. 3 Instructions for Proper Maintenance pg. 4 About Our Wood Limited Warranty pg. 5 Keys to Assembly Success pg. 6 Part ID pg Step-By-Step Instructions pg Installation of I.D./Warning Plaque pg. 97 Registration Last Page

2 Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they understand and follow them. Remember on-site adult supervision is required for children of all ages. SERIOUS HEAD INJURY HAZARD Installation over concrete, asphalt, dirt, grass, carpet and other hard surface creates a risk of serious injury or death from falls to the ground. Install and maintain shock absorbing material under and around play-set as recommended on page 3 of these instructions. COLLISION HAZARD Place play-set on level ground at least 6 feet from any obstruction such as a garage or house, fences, poles, trees, sidewalks, walls, landscape timbers, rocks, pavement, planters, garden borders, overhanging branches, laundry lines, and electrical wires. (See OBSTACLE FREE SAFETY ZONE on cover) CHOKING HAZARD/SHARP EDGES & POINTS Adult assembly required. This product contains small parts and parts with sharp edges and points. Keep parts away from children until fully assembled. WARNING LABEL Owners shall be responsible for maintaining the legibility of the warning labels. WARNING STRANGULATION HAZARD NEVER allow children to play with ropes, clotheslines, pet leashes, cables, chains or cord-like items when using this play-set or to attach these items to play-set. NEVER allow children to wear loose fitting clothing, ponchos, hoods, scarves, capes, necklaces, items with draw-strings, cords or ties when using this play-set. NEVER allow children to wear bike or sport helmets when using this play-set. Failure to prohibit these items, even helmets with chin straps, increases the risk of serious injury and death to children from entanglement and strangulation. TIP OVER HAZARD Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose-fill surfacing materials washing away during heavy rains. DO NOT allow children to play on the play-set until the assembly is complete and the unit is properly anchored. WARNING Safe Play Instructions Observe capacity limitations of your play-set. See front cover. Dress children with well fitting and full foot enclosing footwear. Teach children to sit with their full weight in the center of the swing seat to prevent erratic swing motion or falling off. Check for splintered, broken or cracked wood; missing, loose, or sharp edged hardware. Replace, tighten and or sand smooth as required prior to playing. Verify that suspended climbing ropes, rope ladders, chain or cable are secured at both ends and cannot be looped back on itself as to create an entanglement hazard. On sunny and or hot days, check the slide and other plastic rides to assure that they are not very hot as to cause burns. Cool hot slide and rides with water and wipe dry prior to using. Do not allow children to wear open toe or heel footwear like sandals, flip flops or clogs. Do not allow children to walk, in front, between, behind or close to moving rides. Do not let children twist swing chains or ropes or loop them over the top support bar. This may reduce the strength of the chain or rope and cause premature failure. Do not let children get off rides while they are in motion. Do not permit climbing on equipment when it is wet. Do not permit rough play or use of equipment in a manner for which it was not intended. Standing on or jumping from the roof, elevated platforms, swings, climbers, ladders or slide can be dangerous. Do not allow children to swing empty rides or seats. Do not allow children to go down slide head first or run up slide. 2 support@cedarsummitplay.com

3 Protective Surfacing - Reducing Risk of Serious Head Injury From Falls One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292. There are different types of surfacing to choose from; whichever product you select, follow these guidelines: Loose-Fill Materials Maintain a minimum depth of 9 inches of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or shredded/recycled rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet high. NOTE: An initial fill level of 12 inches will compress to about a 9-inch depth of surfacing over time. The surfacing will also compact, displace, and settle, and should be periodically raked and refilled to maintain at least a 9-inch depth. Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this should be adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.) NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface can result in serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and environmental factors can reduce their shock absorbing effectiveness. Carpeting and thin mats are not adequate protective surfacing. Ground level equipment -- such as a sandbox, activity wall, playhouse or other equipment that has no elevated play surface -- does not need any protective surfacing. Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don t forget to account for water drainage. Periodically rake, check and maintain the depth of the loose-fill surfacing material. Marking the correct depth on the play equipment support posts will help you to see when the material has settled and needs to be raked and or replenished. Be sure to rake and evenly redistribute the surfacing in heavily used areas. Do not install loose fill surfacing over hard surfaces such as concrete or asphalt. Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-place surfaces. Installations of these surfaces generally require a professional and are not do-it yourself projects. Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that the product has been tested to the following safety standard: ASTM F1292 Standard Specification for Impact Attenuation of Surfacing Materials within the Use Zone of Playground Equipment. This report should show the specific height for which the surface is intended to protect against serious head injury. This height should be equal to or greater than the fall height - vertical distance between a designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below - of your play equipment. Check the protective surfacing frequently for wear. Placement Proper placement and maintenance of protective surfacing is essential. Refer to diagram on front cover. Be sure to; Extend surfacing at least 6 feet from the equipment in all directions. For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar from which the swing is suspended. For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all directions. 6 ft. 6 ft. Denotes Use Zone with Protective Surfacing 6 ft. 6 ft. 6 ft. Denotes Use Zone with Protective Surfacing 6 ft. 6 ft. Use Zone for Single-Axis Swings Use Zone for Multi-Axis Swings From the CPSC Outdoor Home Playground Safety Handbook. At 3 support@cedarsummitplay.com

4 Instructions for Proper Maintenance Your Cedar Summit Play System is designed and constructed of quality materials with your child s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it. Check the following at the beginning of the play season: HARDWARE: Check metal parts for rust. If found, sand and repaint using a non-lead paint complying with 16 CFR Inspect and tighten all hardware. On wood assemblies DO NOT OVER- TIGHTEN as to cause crushing and splintering of wood. Check for sharp edges or protruding screw threads, add washers if required. If Bolt protrudes beyond T-Nut Use an extra flat washer SHOCK ABSORBING SURFACING: Check for foreign objects. Rake and check depth of loose fill protective surfacing materials to prevent compaction and maintain appropriate depth. Replace as necessary. (See Protective Surfacing, page 3) GROUND STAKES (ANCHORS): Check for looseness, damage or deterioration. Should firmly anchor unit to ground during use. Re-secure and or replace, if necessary. SWING HANGERS: Check that bolts are secure and tight. Quick clips should be completely closed and threaded clips screwed tight. If squeaking occurs lubricate bushings with oil or WD-40. SWINGS, ROPES AND RIDES: Reinstall if removed during cold season. Check all moving parts including swing seats, ropes, chains and attachments for wear, rust and other deterioration. Replace as needed. Check that ropes are tight, secure at both ends and cannot loop back as to create an entrapment. WOOD PARTS: Check all wood members for deterioration, structural damage and splintering. Sand down splinters and replace deteriorated wood members. As with all wood, some checking and small cracks in grain is normal. Applying a water repellent or stain (water-based) on a yearly basis is important maintenance to maintain maximum life and performance of the product. Check twice a month during play season: HARDWARE: Inspect for tightness. Must be firmly against, but not crushing the wood. DO NOT OVER-TIGHTEN. This will cause splintering of wood. Check for sharp edges or protruding screw threads. Add washers if required. SHOCK ABSORBING SURFACING: Rake and check depth of loose fill protective surfacing materials to prevent compaction and maintain appropriate depth. Replace as necessary. (See Protective Surfacing, page 3) Check once a month during play season: SWING HANGERS: Check that they are secure and orientated correctly. Hook should rotate freely and perpendicular to support beam. If squeaking occurs lubricate bushings with oil or WD-40. SWINGS AND RIDES: Check swing seats, all ropes, chains and attachments for fraying, wear, excessive corrosion or damage. Replace if structurally damaged or deteriorated. Check at the end of the play season: SWINGS AND RIDES: To prolong their life, remove swings and store inside when outside temperature is below 32 F/0 C. Below freezing, plastic parts may become more brittle. SHOCK ABSORBING SURFACING: Rake and check depth of loose fill protective surfacing materials to prevent compaction and maintain appropriate depth. Replace as necessary. (See Protective Surfacing, page 3) If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable hazards at the time it is discarded. Be sure to follow your local waste ordinances. 4 support@cedarsummitplay.com

5 About Our Wood Cedar Summit Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set. What causes weathering? Does it affect the strength of my Play System? One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the surface is different than the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing tension which can result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of the product: 1. Checking is surface cracks in the wood along the grain. A post (4 x 4 ) will experience more checking than a board (1 x 4 ) because the surface and interior moisture content will vary more widely than in thinner wood. 2. Warping results from any distortion (twisting, cupping) from the original plane of the board and often happens from rapid wetting and drying of the wood. 3. Fading happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey over time. How can I reduce the amount of weathering to my Play System? At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, applying a water repellant or stain on a yearly basis is important maintenance. (see your local stain and paint supplier for a recommended product) Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance. Complete and mail registration card to receive important product notifications and assure prompt warranty service. 5 Year Limited Warranty Solowave Design warrants that this product is free from defect in materials and workmanship for a period of one year from the original date of purchase. In addition, lumber is warranted for 5 years against structural failure due to rot and insect damage. All other parts, such as hardware, swings, rides, accessories, and slides carry a one-year warranty only. This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is required to assure the integrity of your Play System. Failure by the owner to maintain the product according to the maintenance requirements may void this warranty. This warranty does not cover any inspection cost. This Limited Warranty does not cover: Labor for replacement of any defective item(s); Incidental or consequential damages; Cosmetic defects which do not affect performance or integrity; Vandalism; improper use or installation; acts of nature; Minor twisting, warping, checking, or any other natural occurring properties of wood that do not affect performance or integrity. Solowave Design products have been designed for safety and quality. Any modifications made to the original product could damage the structural integrity of the unit leading to failure and possible injury. Solowave Design Inc. cannot assume any responsibility for modified products. Furthermore, modification voids any and all warranties. This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Solowave Design Play System be used in public settings such as schools, churches, playgrounds, parks, day cares and the like. Such use may lead to product failure and potential injury. Any and all public use will void this warranty. Solowave Design disclaims all other representations and warranties of any kind, express or implied. This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or province to province. This warranty excludes all consequential damages, however, some states do not allow the limitation or exclusion of consequential damages, and therefore this limitation may not apply to you. 5 support@cedarsummitplay.com

6 Tools Required Keys to Assembly Success Shovel Measuring Drill (1/8 Safety Hammer Ratchet 1/2, Level #2 & #3 Phillips Tape 3/16 Bit) Glasses 7/16 & 9/16 or Robertson Square Ruler Step Ladder Part Identification Key On each page, you will find the parts and quantities required to complete the assembly step illustrated on that page. Here is a sample. 2X 1234 Post 2 x 4 x 83 Symbols Throughout these instructions symbols are provided as important reminders for proper and safe assembly. This identifies information that requires special attention. Improper assembly could lead to an unsafe or dangerous condition. Use Help Measure Distance Use Help Where this is shown, 2 or 3 people are required to safely complete the step. To avoid injury or damage to the assembly make sure to get help! Check that assembly is square before tightening bolts. Use a measuring tape to assure proper location. Square Assembly Check that set or assembly is properly level before proceeding. Pre-drill 1/8 Bit Pre-drill a pilot hole before fastening screw or lag to prevent splitting of wood. This indicates time to tighten bolts, but not too tight! Do not crush the wood. This may create splinters and cause structural damage. Use Level Tighten Bolts CAUTION Protrusion Hazard Once the assembly is tightened, watch for exposed threads. If a thread protrudes from the T-Nut, remove the bolt and add washers to eliminate this condition. Extra washers have been provided for this purpose. Proper Assembly Lag screws require drilling pilot holes to avoid splitting wood. Only a flat washer is required. For ease of installation liquid soap can be used on all lag-type screws. For bolts, tap T-Nut into hole with hammer. Insert the hex bolt through lock washer first then flat washer then hole. Because the assemblies need to be squared do not completely tighten until instructed. Pay close attention to diameter of the bolts. 5/16 is slightly larger than 1/4. No Yes 6 6 support@cedarsummitplay.com

7 Part Identification (Reduced Part Size) 1pc /8 x 2-3/4 x 19-3/4" - Rockwall Top - Box pc Ground Stake 1-1/4 x 1-1/2 x 14" - Box 1 & Nominal Size Actual Size 1-1/4 x 1-1/2 1-1/4 x 1-1/2 1 x 2 5/8 x 1-3/8 1 x 3 5/8 x 2-3/8 1 x 4 5/8 x 3-3/8 1 x 5 5/8 x 4-3/8 1pc x 2 x 22" - Dormer Bottom - Box pc x 2 x 26" - Bottom Window - Box pc x 3 x 6-3/4" - Dormer Side Burst - Box pc x 3 x 10-3/4" - Dormer Centre - Box pc x 3 x 13-5/8" - Dormer Side - Box pc x 4 x 10-5/8" - Spacer A - Box pc x 4 x 10-15/16" - Gable Board A - Box pc x 4 x 14" - Spacer B - Box pc x 4 x 16-1/8" - Centre Gable Board - Box pc x 4 x 26-1/2" - Wall Board - Box pc x 4 x 29" - Cedar Wall - Box pc x 4 x 29-3/4" - Top End Nest - Box (2 NOT REQUIRED) 1pc x 4 x 5-1/2" - Dormer Burst - Box pc x 5 x 27" - Floor Board - Box pc x 5 x 32-1/2" - Wall Board - Box pc x 5 x 38-1/2" - Floor Board - Box support@cedarsummitplay.com

8 Part Identification (Reduced Part Size) 1pc x 5 x 57" - Middle Back - Box pc x 6 x 21" - Gable A - Box Nominal Size Actual Size 1 x 6 5-1/4 5/4 x 2 15/16 x 1-1/2 5/4 x 3 15/16 x 2-1/4 5/4 x 4 15/16 x 3-1/4 4pc x 6 x 19-3/4" - Rock Board A - Box pc x 6 x 19-3/4" - Rock Board B - Box pc x 6 x 19-3/4" - Access Board - Box pc /8 x 5-1/4 x 31-1/2" - Crowsnest Floor Board - Box pc x 6 x 31" - SW Nest Wall - Box pc x 6 x 38-1/2" - Floor - Box pc x 6 x 57" - Back Top - Box pc x 6 x 25-3/8" - Crowsnest Floor - Box pc /4 x 2 x 17" - Spindle - Box pc /4 x 2 x 33" - Long Spindle - Box pc /4 x 3 x 34-1/4" - SW Table Top - Box pc /4 x 4 x 7-3/4" - Short Rail - Box support@cedarsummitplay.com

9 Part Identification (Reduced Part Size) 2pc /4 x 4 x 11-1/4" - End Nest Board - Box Nominal Size Actual Size 5/4 x 4 15/16 x 3-1/4 1pc /4 x 4 x 13-5/8" - Bench Support - Box /4 x 5 15/16 x 4-1/4 1pc /4 x 4 x 24-1/4" - Cafe Top - Box pc /4 x 4 x 29-3/4" - Bottom Nest End - Box pc /4 x 4 x 29-3/4" - End Nest Top - Box pc /4 x 4 x 33-7/8" - Side Nest Top - Box pc /4 x 4 x 34" - Roof Support Left - Box pc /4 x 4 x 34" - Roof Support Right - Box pc /4 x 4 x 39-1/4" - Lower Side - Box pc /4 x 4 x 54-1/2" - Back Ground - Box pc /4 x 4 x 57" - Front Top Bottom - Box pc /4 x 4 x 88-43/64" - Ground SW - Box pc /4 x 5 x 15-5/8" - Crowsnest Bottom Front - Box pc /4 x 5 x 15-5/8" - Crowsnest Top Front - Box support@cedarsummitplay.com

10 Part Identification (Reduced Part Size) 1pc /4 x 5 x 32-7/8" - SL Bottom - Box pc /4 x 6 x 5" - Seat Side - Box Nominal Size Actual Size 5/4 x 5 15/16 x 4-1/4 5/4 x 6 15/16 x 5-1/4 5/4 x 4 1 x 3-1/2 2 x 3 1-1/2 x 2-1/4 2 x 4 1-1/2 x 3-1/4 1pc /4 x 6 x 10" - Sunburst - Box pc /4 x 6 x 29-1/2" - Seat - Box pc /4 x 4 x 23" - Rockwall Brace - Box pc /4 x 4 x 25-1/2" - Crowsnest Back - Box pc /4 x 4 x 34-3/8" - Crowsnest Upright - Box pc /8 x 1-3/4 x 13-3/4" - Ladder Step - Box pc x 3 x 25" - SW Nest Access Post - Box pc x 3 x 27-3/4" - Crowsnest Face B - Box pc x 3 x 32" - Rockwall Post - Box pc x 3 x 42-1/4" - Diagonal - Box pc x 4 x 3-1/4" - Seat Block - Box pc x 4 x 9" - Gusset - Box support@cedarsummitplay.com

11 Part Identification (Reduced Part Size) 1pc x 4 x 13-1/2" - Bench Leg - Box Nominal Size Actual Size 2 x 4 1 3/8 x 3-3/8 1-1/4 x 3-3/8 1-1/4 x 3-3/8 1pc x 4 x 26-1/4" - SL Support - Box pc x 4 x 29" - SW Mount - Box pc x 4 x 38" - Floor Support - Box pc x 4 x 38-3/8" - Crowsnest Post - Box pc x 4 x 38-1/2" - Floor End - Box pc x 4 x 41" - Gable Bottom - Box pc x 4 x 47-7/8" - Back Wall Support - Box pc x 4 x 62-7/8" - Rock Rail - Box pc x 4 x 68" - FR Floor Support - Box pc x 4 x 68" - Floor Joist - Box pc x 4 x 68" - Back Floor Support - Box pc x 4 x 102" - Post - Box pc /4 x 3-3/8 x 23-3/4" - SW Side Post - Box support@cedarsummitplay.com

12 Part Identification (Reduced Part Size) 1pc x 6 x 31-3/4" - Lower Gable - Box pc x 3 x 37-5/8" - Nest Post - Box Nominal Size Actual Size 2 x 6 1-1/4 x 5-1/4 2 x 3 1-3/8 x 2-1/2 2 x 4 1-3/8 x 3-3/8 2 x 2 1-1/2 x 1-1/2 2 x 6 1-1/2 x 5-3/8 2 x 3-3/8 2 x 3-3/8 1pc x 4 x 5-3/8" - SW Rail Block - Box pc x 4 x 8-5/8" - Crowsnest Joist - Box pc x 4 x 10" - Dormer Cleat - Box pc x 4 x 27-1/2" - Crowsnest Face - Box pc x 4 x 38-1/2" - Crowsnest Top - Box pc x 4 x 38-1/2" - Crowsnest Floor End - Box pc x 4 x 46-1/2" - Heavy SW Support - Box pc x 4 x 48-5/16" - SW Upright - Box pc x 6 x 94" - Front Beam - Box pc x 6 x 94" - Back Beam - Box pc x 3-3/8 x 86-11/16" - Heavy SW Post - Box support@cedarsummitplay.com

13 Part Identification (Reduced Part Size) 2728 (1) MK Ground 1 x 4 x 49-15/ Box 5 (3) Tennon Dowel 1 1/8" x 15 7/8" Box (2) Tennon Dowel 1 1/8" x 18 5/8" Box 5 (1) Short Diagonal 2 x 3 x 18" Box 5 Nominal Size 2" x 4" 2" x 3" 5/4" x 5" 1" x 4" Actual Size 1⅜" x 3⅜" 1⅜" x 2½" 1" x 4½" ⅝" x 3⅜" (1) MK Lower Back 5/4 x 5 x 34-1/8" Box 5 (1) Long Diagonal 2 x 3 x 42" Box 5 (2) MK Post 2 x 4 x 80-7/8" Box 5 (2) MK Rail Short 2 x 4 x 50" Box 5 1pc Dormer Roof Set - Box pc /4 x 35-7/16 x 64" - Roof Panel - Box support@cedarsummitplay.com

14 Part Identification (Reduced Part Size) 1pc /4 x 28-1/2 x 102" Cafe Panel - Box pc /4 x 28-1/2 x 102" Chalkwall Panel - Box pc /4 x 38-1/2 x 83" SW Wall Panel - Box pc /4 x 38-1/2 x 54-1/8" SL Side Panel - Box support@cedarsummitplay.com

15 Identification (Actual Size) 8pc. H2 - Hex Bolt 1/4 x 2" - ( ) 35pc. H10 - Hex Bolt 1/4 x 2-1/4" - ( ) 21pc. H3 - Hex Bolt 1/4 x 2-1/2" - ( ) 4pc. H11 - Hex Bolt 1/4 x 2-3/4" - ( ) 3pc. H12 - Hex Bolt 1/4 x 3" - ( ) 3pc. H13 - Hex Bolt 1/4 x 3-1/2" - ( ) 2pc. H4 - Hex Bolt 1/4 x 4" - ( ) 2pc. LS2 - Lag Screw 1/4 x 2-1/2" - ( ) 19pc. WL5 - Wafer Lag 1/4 x 2-1/2" - ( ) 2pc. G10 - Hex Bolt 5/16 x 3" - ( ) 1pc. H8 - Hex Bolt 1/4 x 4-1/4" - ( ) 8pc. WL3 - Wafer Lag 1/4 x 1-3/8" - ( ) 4pc. H7 - Hex Bolt 1/4 x 5-1/2" - ( ) 8pc. G1 - Hex Bolt 5/16 x 1-1/2" - ( ) 2pc. G4 - Hex Bolt 5/16 x 4" - ( ) 4pc. G5 - Hex Bolt 5/16 x 4-1/2" - ( ) 2pc. G8 - Hex Bolt 5/16 x 2" - ( ) 3pc. G6 - Hex Bolt 5/16 x 4-3/4" - ( ) 4pc. G7 - Hex Bolt 5/16 x 5-1/2" - ( ) 2pc. G25 - Hex Bolt 5/16 x 7-1/4" - ( ) 15 support@cedarsummitplay.com

16 Identification (Actual Size) 19pc. LW2-5/16" Lock - ( ) 15pc. FW0-3/16" Flat - ( ) 89pc. TN1-1/4" T - Nut -( ) 96pc. LW1-1/4" Lock - ( ) 103pc. FW1-1/4" Flat - ( ) 19pc. TN2-5/16" T- Nut - ( ) 91pc. LN1-1/4 Lock Nut - ( ) 45pc. FW2-5/16" Flat - ( ) 12pc. LN2-5/16" Lock Nut - ( ) 7pc. BN1-1/4" Barrel Nut - ( ) 1pc. - D4 -#2 x 2" Robertson Driver Bit- ( ) 89pc. PB1 - Pan Bolt 1/4 x 3/4" - ( ) 12pc. PB2 - Pan Bolt 1/4 x 1-1/4" - ( ) 8pc. FW6 - #12 Screw Bezel - ( ) 5pc. PB6 - Pan Bolt 1/4 x 1" - ( ) 2pc. -PB5 -Pan Bolt 1/4 x 2 - ( ) 4pc. S18 - Wood Screw #6 x 1" - ( ) 22pc. S5 - Pan Screw #8 x 1/2" - ( ) 22pc. S1 - Wood Screw #8 x 1-1/8" - ( ) 8pc. S10 - Pan Screw #8 x 1" - ( ) 236pc. S20 - Wood Screw #8 x 1-3/8" - ( ) 40pc. S8 - Pan Screw #12 x 3/4" - ( ) 95pc. S15 - Wood Screw #8 x 1-3/4" - ( ) 23pc. S6 - Pan Screw #12 x 1" - ( ) 64pc. S3 - Wood Screw #8 x 2-1/2" - ( ) 61pc. S7 - Pan Screw #12 x 2" - ( ) 28pc. S4 - Wood Screw #8 x 3" - ( ) 16 support@cedarsummitplay.com

17 Part Identification (Reduced Part Size) 2x - Space Glider Handle ( ) Green 1x - Space Glider Body ( ) Yellow 1x - TNR 2 Slide Exit ( ) 1x - Telescope w/ Mount ( ) 1x - TNR 2 Post Mount ( ) 2x - Hand Grip (2Pk) ( ) -Yellow 1x - Rocks (7pk) ( ) -Green/Yellow 1x - (4pk) Swing Bracket Set ( ) -Green 1x - Cedar Summit Plaque ( ) 1x - Cedar Summit ID Plaque ( ) 1x - EN71 Hand Rail ( ) -Yellow 10x - TNR 2 Slide Clamp Ring ( ) 9x - TNR 2 Slide Elbow ( ) 1x - Quadrex Driver ( ) 2x - Monkey Bracket ( ) 1x - Plastic Swing Hanger Cover (8Pk) ( ) 1x - TNR 2 Slide Exit Top ( ) 2x - MB Hanger Bracket ( ) 1x - Triangle Plate (4pk) ( ) Green 1x - TNR 2 Slide Support ( ) 1x - Spin Chalk Sign ( ) 1x - Bolt Thru Swing Hanger (4Pk) ( ) 1x - TNR 2 Slide Lt Flange ( ) X - Wall Angle Bracket 1x - TNR 2 Slide Rt Flange ( ) 1x - Bayfield Retreat Brkt Set ( ) X - Corner Bracket 1x - Maze N Wave 2.5m Slide ( ) 1x - Glider Hanger (2pk) ( ) 1x - 39" Glider Rope & Chain (4Pk) ( ) 2x - 42" Belt Swing w/ Welded Chain ( ) Yellow X - Corner Panel Brkt X - Flat Panel Brkt 17 support@cedarsummitplay.com

18 Step 1: Inventory Parts - Read This Before Starting Assembly STOP STOP STOP STOP A. This is the time for you to inventory all your hardware, wood and accessories, referencing the parts identification sheets. This will assist you with your assembly. The wood pieces will have the four digit key number stamped on the ends of the boards. The wood pieces are referenced throughout the instructions with this number. Please refer to Page 6 for proper hardware assembly. Each step indicates which bolts and/or screws you will need for assembly, as well as any flat washers, lock washers, t-nuts or lock nuts. B. If there are any missing or damaged pieces or you need assistance with assembly please contact the Consumer Relations Department directly. Call us before going back to the store support@solowavedesign.com C. Read the assembly manual completely, paying special attention to ANSI warnings; notes; and safety/maintenance information on pages 1-6. D. Before you discard your cartons fill out the form below. The carton I.D. stamp is located on the end of each carton. The tracking number is located on the Big Backyard ID Plaque ( ). Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department. MODEL NUMBER: F23931 CARTON I.D. STAMP: (Box 1) CARTON I.D. STAMP: (Box 2) CARTON I.D. STAMP: (Box 3) CARTON I.D. STAMP: (Box 4) CARTON I.D. STAMP: (Box 5) CARTON I.D. STAMP: (Box 6) TRACKING NUMBER (from ID Plaque): 18 support@cedarsummitplay.com

19 Step 2: Rockwall Assembly Part 1 A: Attach Swing Brackets flush to the inside top of each (8139) Rock Rail at angled edge using 1 (G1) 5/16 x 1-1/2 Hex Bolt (with lock washer, flat washer and t-nut) per bracket. Edge of Swing Bracket is flush with edges of Access Rails. (fig. 2.1 and 2.2) B: Place (2727) Rockwall Top at the top of the (8139) Rock Rails so it is flush on the right side then attach with 3 (S15) #8 x 1-3/4 Wood Screws. (fig. 2.1 and 2.2) Right Side Fig Left Side /16 T-Nut 5/16 Flat Fig. 2.2 G1 5/16 Lock Flush 8139 Swing Bracket Swing Bracket S15 Flush to edges 2727 S15 Wood Parts 2 x 8139 Rock Rail 2 x 4 x 62-7/8 1 x 2727 Rockwall Top 5/8 x 2-3/4 x 19-3/4 3 x S15 #8 x 1-3/4 Wood Screw 2 x G1 5/16 x 1-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) Other Parts 2 x Swing Bracket 19 support@cedarsummitplay.com

20 Step 2: Rockwall Assembly Part 2 C: Place (2605) Access Board on (8139) Rock Rails, tight to (2727) Rockwall Top. Pilot holes to line up over (8139) Rock Rails. Do not attach to rails in this step, it is being used as a guide. (fig. 2.3) D: Place (2730) Rockwall Brace flush to the bottom of (8139) Rock Rails and flush to the right side (8139) Rock Rail so it overhangs the left side, pilot holes to line up over (8139) Rock Rails, then attach with 4 (S15) #8 x 1-3/4 Wood Screws. (fig. 2.3) E: In between the (2605) Access Board and (2730) Rockwall Brace stagger 4 (2603) Rock Board As and 3 (2604) Rock Board Bs. Make sure the boards are evenly spaced and do not exceed 2-1/4 between boards. Then attach using 4 (S20) #8 x 1-3/8 Wood Screws per board. Placing them as shown in fig. 2.3 will prevent rocks from forming a straight line. F: Set aside (2605) Access Board. It will be attached in Step 14, Part 1. Fig. 2.3 Left Side S20 x 4 per board S15 x Tight Notice board extended at this end Evenly spaced not to exceed 2-1/4 gap between all boards 8139 Flush Right Side Wood Parts 1 x 2605 Access Board 1 x 6 x 19-3/4 4 x 2603 Rock Board A 1 x 6 x 19-3/4 3 x 2604 Rock Board B 1 x 6 x 19-3/4 1 x 2730 Rockwall Brace 5/4 x 4 x 23 4 x S15 #8 x 1-3/4 Wood Screw 28 x S20 #8 x 1-3/8 Wood Screw 20 support@cedarsummitplay.com

21 Step 3: Attach Rocks A: Alternating colours and shapes, attach 1 rock to each rock board using 1 (PB2) 1/4 x 1-1/4 Pan Bolt (with 1/4 lock washer, 3/16 flat washer and 1/4 barrel nut) and 1 (S10) #8 x 1 Pan Screw per rock. (fig. 3.1 and 3.2) The Pan Screw is placed in the hole beneath the Pan Bolt. (fig. 3.1 and 3.2) Note: Make sure all hardware is used to secure each rock properly. Fig. 3.1 Fig /16 Flat 1/4 Barrel Nut 1/4 Lock PB2 S10 Rock 7 x PB2 1/4 x 1-1/4 Pan Bolt (1/4 lock washer, 3/16 flat washer & 1/4 barrel nut) 7 x S10 #8 x 1 Pan Screw Other Parts 7 x Rocks (green/yellow) 21 support@cedarsummitplay.com

22 Step 4: Swing Wall Panel Assembly Part 1 A: Place (2528) SW Wall Panel on the ground then measure 4 up from the bottom of the panel and 4 down from the top of the panel on both sides and attach four 2 x 2-1/4 Corner Panel Brackets to the panel with 2 (S8) #12 x 3/4 Pan Screws per bracket. The flat edges of the brackets sit flat against the panel. (fig. 4.1 and 4.2) B: With a helper hold (2526) Cafe Panel up against the right side edge of (2528) SW Wall Panel so the bottom edges are flush. Attach Corner Panel Brackets to (2526) Cafe Panel with 2 (S8) #12 x 3/4 Pan Screws per bracket. (fig. 4.1 and 4.2) C: Place (2473) Post up against the left side of (2528) SW Wall Panel so the bottom edges are flush, noticing the hole locations in the top of the board, then attach Corner Panel Brackets to (2473) Post with 2 (S8) #12 x 3/4 Pan Screws per bracket. (fig. 4.1 and 4.2) Fig. 4.2 S8 x 4 per bracket Notice holes facing up Fig x 2-1/4 Corner Panel Bracket Flat edge 2 x 2-1/4 Corner Panel Bracket x 2-1/4 Corner Panel Bracket 4 Flush Bottom 2 x 2-1/4 Corner Panel Bracket Flush Wood Parts Other Parts 1 x 2526 Cafe Panel 1-1/4 x 28-1/2 x x S8 #12 x 3/4 Pan Screw 4 x 2 x 2-1/4 Corner Panel Bracket 1 x 2528 SW Wall Panel 1-1/4 x 38-1/2 x 83 1 x 2473 Post 2 x 4 x support@cedarsummitplay.com

23 Step 4: Swing Wall Panel Assembly Part 2 Note: Make sure panels are square and flush to each other. (fig. 4.3) D: Pre-drill with a 3/16 drill bit, then fasten the (2526) Cafe Panel and (2473) Post to (2528) SW Wall Panel with 5 (WL5) 1/4 x 2-1/2 Wafer Lags per panel. (fig. 4.3) 2526 Fig WL5 WL5 10 x WL5 1/4 x 2-1/2 Wafer Lag 23 support@cedarsummitplay.com

24 Step 5: Slide Wall Panel Assembly Part 1 A: Place (2529) SL Side Panel on the ground then measure 4 up from the bottom of the panel and 4 down from the top of the panel on both sides and attach four 2 x 2-1/4 Corner Panel Brackets to the panel with 2 (S8) #12 x 3/4 Pan Screws per bracket. The flat edge of the bracket must be sitting flat against the panel. (fig. 5.1 and 5.2) B: With a helper hold (2527) Chalkwall Panel up against the left side edge of (2529) SL Side Panel so the bottom edges are flush. Attach Corner Panel Brackets to (2527) Chalkwall Panel with 2 (S8) #12 x 3/4 Pan Screws per bracket. (fig. 5.1 and 5.2) C: Place (2473) Post up against the right side of (2529) SL Side Panel so the bottom edges are flush, noticing the hole locations in the top of the board, then attach Corner Panel Brackets to (2473) Post with 2 (S8) #12 x 3/4 Pan Screws per bracket. (fig. 5.1 and 5.2). Fig. 5.1 Notice holes facing up S8 x 4 per bracket Fig Flat edge 2 x 2-1/4 Corner Panel Bracket 2 x 2-1/4 Corner Panel Bracket 2 x 2-1/4 Corner Panel Bracket 4 4 Flush Flush Bottom Wood Parts 1 x 2527 Chalkwall Panel 1-1/4 x 28-1/2 x x 2529 SL Side Panel 1-1/4 x 38-1/2 x 54-1/8 1 x 2473 Post 2 x 4 x x S8 #12 x 3/4 Pan Screw Other Parts 4 x 2 x 2-1/4 Corner Panel Bracket 24 support@cedarsummitplay.com

25 Step 5: Slide Wall Panel Assembly Part 2 Note: Make sure panels are square and flush to each other. (fig. 5.3) D: Pre-drill with a 3/16 drill bit, then fasten the (2527) Chalkwall Panel and (2473) Post to (2529) SL Side Panel with 3 (WL5) 1/4 x 2-1/2 Wafer Lags per panel. (fig. 5.3) 2527 Fig WL5 WL5 6 x WL5 1/4 x 2-1/2 Wafer Lag 25 support@cedarsummitplay.com

26 Step 6: Join Slide Wall and Swing Wall Assemblies A: With a helper lift the Swing Wall Assembly and Slide Wall Assembly so the (2526) Cafe Panel and (2527) Chalkwall Panel are tight together. (fig. 6.1) B: Attach 1 (2492) Front Top Bottom to the bottom and 1 to top of (2526) Cafe Panel and (2527) Chalkwall Panel with 4 (H10) 1/4 x 2-1/4 Hex Bolts (with lock washer, flat washer and t-nut) per board as shown in fig C: Attach (2475) FR Floor Support to the centre of (2526) Cafe Panel and (2527) Chalkwall Panel so one end extends past the Slide Side using 4 (H3) 1/4 x 2-1/2 Hex Bolts (with lock washer, flat washer and t-nut) as shown in fig Fig. 6.1 Back Swing Side 1/4 T-Nut 1/4 Flat /4 Lock H10 1/4 T-Nut 1/4 Flat 1/4 Lock H Extended on this side H10 Slide Side 2527 Front Wood Parts 2 x 2492 Front Top Bottom 5/4 x 4 x 57 1 x 2475 FR Floor Support 2 x 4 x 68 8 x H10 1/4 x 2-1/4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 4 x H3 1/4 x 2-1/2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 26 support@cedarsummitplay.com

27 Step 7: Top Swing Side Wall Assembly A: Place 1 (2521) SW Side Post tight to the top and flush to the front face of (2528) SW Wall Panel and flush to the outside edge of (2526) Cafe Panel. Attach with 3 (S3) #8 x 2-1/2 Wood Screws. (fig. 7.1 and 7.2) B: Place a second (2521) SW Side Post tight to the top and flush to the front face of (2528) SW Wall Panel and flush to the outside edge of (2473) Post. Attach with 3 (S3) #8 x 2-1/2 Wood Screws. (fig. 7.1 and 7.2) Fig. 7.1 Back Notice orientation of angles Fig Front Swing Side 2521 S Flush S Flush Wood Parts 2 x 2521 SW Side Post 1-1/4 x 3-3/8 x 23-3/4 6 x S3 #8 x 2-1/2 Wood Screw 27 support@cedarsummitplay.com

28 Step 8: Back Wall Assembly Part 1 A: Place (2493) Back Ground in between both (2473) Posts on the inside of the assembly. Attach (2493) Back Ground to (2473) Post on the Swing Side with 1 (H10) 1/4 x 2-1/4 Hex Bolt (with lock washer, flat washer and t-nut). (fig. 8.1) B: Place (2524) SL Bottom on the outside of (2473) Post on the Slide Side and attach to (2473) Post and (2493) Back Ground with 1 (H12) 1/4 x 3 Hex Bolt (with lock washer, flat washer and t-nut) in the bottom hole. (fig. 8.1) C: Attach (8168) SL Support to extended end of (2524) SL Bottom with 1 (H10) 1/4 x 2-1/4 Hex Bolt (with lock washer, flat washer and t-nut) in the top hole. (fig. 8.1) D: Make sure (2524) SL Bottom is square to (2473) Post and (8168) SL Support then attach with 2 (S15) #8 x 1-3/4 Wood Screws in remaining holes. (fig. 8.1) Fig. 8.1 Slide Side /4 T-Nut /4 Flat 1/4 Lock H S15 Swing Side 2473 H H12 Back Wood Parts 1 x 2493 Back Ground 5/4 x 4 x 54-1/2 2 x H10 1/4 x 2-1/4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 1 x 2524 SL Bottom 5/4 x 5 x 32-7/8 1 x 8168 SL Support 2 x 4 x 26-1/4 1 x H12 1/4 x 3 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 2 x S15 #8 x 1-3/4 Wood Screw 28 support@cedarsummitplay.com

29 Step 8: Back Wall Assembly Part 2 E: From inside the assembly loosely attach (2477) Back Floor Support to both (2473) Posts with 2 (H3) 1/4 x 2-1/2 Hex Bolts (with lock washer, flat washer and t-nut). Notice that the bolt on the Swing Side is installed from inside the assembly and the bolt on the Slide Side is installed from outside the assembly. (fig. 8.2) F: Loosely attach (2480) Back Top to the top of both (2473) Posts and (2494) Middle Back below (2480) Back Top using 2 (H2) 1/4 x 2 Hex Bolts (with lock washer, flat washer and t-nut) per board in the top holes. (fig. 8.2) G: Loosely attach (2482) Back Wall Support on the inside of (2480) Back Top and (2494) Middle Back with 2 (H2) 1/4 x 2 Hex Bolts (with lock washer, flat washer and t-nut) and to the outside of (2477) Back Floor Support with 1 (H3) 1/4 x 2-1/2 Hex Bolt (with lock washer, flat washer and t-nut) as shown in fig H: Attach (2528) SW Wall Panel to (2477) Back Floor Support and (2475) FR Floor Support with 2 (S4) #8 x 3 Wood Screws per board. (fig. 8.2) I: Make sure assembly is square then tighten all bolts. (fig. 8.2) Fig /4 T-Nut 1/4 Flat 1/4 Lock H2 x 3 per board (hidden) Slide Side H3 x 3 S4 Notice this bolt is inverted Swing Side 2473 Wood Parts 1 x 2480 Back Top 1 x 6 x 57 3 x H3 1/4 x 2-1/2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 1 x 2494 Middle Back 1 x 5 x 57 1 x 2477 Back Floor Support 2 x 4 x 68 1 x 2482 Back Wall Support 2 x 4 x 47-7/8 6 x H2 1/4 x 2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 4 x S4 #8 x 3 Wood Screw 29 support@cedarsummitplay.com

30 Step 9: Attach Spin Chalk Sign and Secure Assembly A: From inside the assembly place the Spin Chalk Sign in the opening of (2527) Chalkwall Panel so it sits tight to the panel and attach with 6 (S5) #8 x 1/2 Pan Screws as shown in fig. 9.1 and 9.2. B: Make sure assembly is square then on the inside of the assembly attach (2526) Cafe Panel to (2527) Chalkwall Panel using 2 Flat Panel Brackets with 4 (S8) #12 x 3/4 Pan Screws per bracket as shown in fig. 9.1 and 9.3. C: Attach (2480) Back Top and (2494) Middle Back to both (2473) Posts and (2482) Back Wall Support with 3 (S20) #8 x 1-3/8 Wood Screws per board. (fig. 9.1 and 9.4) Fig Fig Fig. 8.5 S20 x 3 per board Fig Fig. 9.2 Flat Panel Bracket S8 x 4 per bracket x 6 S5 Spin Chalk Sign 8 x S8 #12 x 3/4 Pan Screw 6 x S5 #8 x 1/2 Pan Screw Other Parts 2 x Flat Panel Bracket 1 x Spin Chalk Sign 6 x S20 #8 x 1-3/8 Wood Screw 30 support@cedarsummitplay.com

31 Step 10: Attach Joist and Floor End Part 1 A: Install one 5/16 T-Nut into (2528) SW Wall Panel as shown in fig and Fig Fig /16 T-Nut 1 x 5/16 T-nut 31 support@cedarsummitplay.com

32 Step 10: Attach Joist and Floor End Part 2 B: At the end of (2477) Back Floor Support and (2475) FR Floor Support attach (2489) Floor End, flush to the ends, with 4 (S4) #8 x 3 Wood Screws. (fig and fig. 10.4) C: Measure 5/8 down from the spot shown on (2528) SW Wall Panel and attach (2476) Floor Joist to (2528) SW Wall Panel and flush to top of (2489) Floor End with 2 (S4) #8 x 3 Wood Screws per end. (fig and fig. 10.5) Fig Fig Fig Flush S4 Outside View 2528 S / S4 x Flush 2477 Wood Parts 1 x 2489 Floor End 2 x 4 x 38-1/2 1 x 2476 Floor Joist 2 x 4 x 68 8 x S4 #8 x 3 Wood Screw 32 support@cedarsummitplay.com

33 Step 11: Floor Board Assembly Part 1 A: Place 1 (2478) Floor tight to (2528) SW Wall Panel and 1 (2478) Floor flush to the face and ends of (2489) Floor End then attach with 6 (S20) #8 x 1-3/8 Wood Screws per board. (fig and 11.2) Fig Fig S Flush S20 x 6 per board Flush 2477 Wood Parts 2 x 2478 Floor 1 x 6 x 38-1/2 12 x S20 #8 x 1-3/8 Wood Screw 33 support@cedarsummitplay.com

34 Step 11: Floor Board Assembly Part 2 B: Starting at Swing Side place 5 (2478) Floors next to the previously installed (2478) Floor then place 1 (2479) Floor Board followed by the remaining 5 (2478) Floors. Make sure the boards are evenly spaced then attach with 6 (S20) #8 x 1-3/8 Wood Screws per board. (fig and 11.4) Fig Fig S20 Flush Swing Side S20 x 6 per board Flush Wood Parts 10 x 2478 Floor 1 x 6 x 38-1/2 1 x 2479 Floor Board 1 x 5 x 38-1/2 66 x S20 #8 x 1-3/8 Wood Screw 34 support@cedarsummitplay.com

35 Step 12: Swing Wall Assembly Part 1 A: Loosely attach (2474) Ground SW to the bottom of (2528) SW Wall Panel using 4 (H10) 1/4 x 2-1/4 Hex Bolts (with lock washer, flat washer and t-nut). (fig. 12.1) B: On the Front of the assembly loosely attach (2491) Diagonal to the end of (2474) Ground SW with 1 (H10) 1/4 x 2-1/4 Hex Bolt (with lock washer, flat washer and t-nut). (fig. 12.1) C: Pre-drill pilot hole with a 3/16 drill bit then attach (2491) Diagonal to (2526) Cafe Panel with 1 (WL5) 1/4 x 2-1/2 Wafer Lag (with flat washer). (fig. 12.1) D: Attach (2485) Seat Side and (2496) Seat Block to (2491) Diagonal with 1 (H13) 1/4 x 3-1/2 Hex Bolt (with lock washer, flat washer and t-nut) and 1 (S15) #8 x 1-3/4 Wood Screw as shown in fig and The tops of (2485) Seat Side and (2496) Seat Block must be flush to each other and both level. E: Tighten all bolts in this step. Fig Fig H /4 T-Nut Flush 1/4 Flat /4 Lock /4 Flat WL5 S Front 2491 H10 Swing Side Wood Parts 1 x 2474 Ground SW 5/4 x 4 x 88-43/64 5 x H10 1/4 x 2-1/4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 1 x 2491 Diagonal 2 x 3 x 42-1/4 1 x H13 1/4 x 3-1/2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 1 x 2485 Seat Side 5/4 x 6 x 5 1 x WL5 1/4 x 2-1/2 Wafer Lag (1/4 flat washer) 1 x 2496 Seat Block 2 x 4 x 3-1/4 1 x S15 #8 x 1-3/4 Wood Screw 35 support@cedarsummitplay.com

36 Step 12: Swing Wall Assembly Part 2 F: In the opening of (2528) SW Wall Panel attach (2483) SW Table Top, tight to the corners of the panel opening, with 3 (S3) #8 x 2-1/2 Wood Screws as shown in fig G: Attach (2486) SW Mount to (2528) SW Wall Panel with 2 (G5) 5/16 x 4-1/2 Hex Bolt (with lock washer, flat washer and t-nut). Note the bottom bolt uses the t-nut previously installed in Step 10, Part 1. (fig. 12.3) Fig /16 T-Nut 5/16 Flat 5/16 Lock G G5 Tight S Note: Bottom bolt uses 5/16 t-nut previously installed Tight 2483 Wood Parts 1 x 2483 SW Table Top 5/4 x 3 x 34-1/4 3 x S3 #8 x 2-1/2 Wood Screw 1 x 2486 SW Mount 2 x 4 x 29 2 x G5 5/16 x 4-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 36 support@cedarsummitplay.com

37 Step 13: Cafe Seat Assembly Part 1 A: Attach (2485) Seat Side to (2484) Bench Leg with 1 (H10) 1/4 x 2-1/4 Hex Bolt (with lock washer, flat washer and t-nut) and 2 (S15) #8 x 1-3/4 Wood Screws as shown in fig The top of (2485) Seat Side must be level and flush to (2484) Bench Leg. B: Attach (2495) Bench Support to (2484) Bench Leg with 1 (H10) 1/4 x 2-1/4 Hex Bolt (with lock washer, flat washer and t-nut) and 1 (S15) #8 x 1-3/4 Wood Screw as shown in fig C: Place Bench Leg Assembly in front of (2526) Cafe Panel and hold (8039) Wall Board against Bench Leg Assembly so it is tight to both (2485) Seat Sides. Attach to (2484) Bench Leg and (2496) Seat Block with 4 (S20) #8 x 1-3/8 Wood Screws. (fig and 13.3) D: Place (2497) Seat on top of each (2485) Seat Side, tight to (2491) Diagonal so the angled edges face out and attach to (2484) Bench Leg and (2496) Seat Block with 4 (S3) #8 x 2-1/2 Wood Screws. (fig and 13.3) Fig Fig H S /4 T-Nut H10 1/4 Lock 1/4 Flat Fig Tight (hidden) 2485 S3 x Tight Tight S20 Wood Parts 1 x 2484 Bench Leg 2 x 4 x 13-1/2 1 x 2495 Bench Support 5/4 x 4 x 13-5/8 1 x 2485 Seat Side 5/4 x 6 x 5 1 x 8039 Wall Board 1 x 4 x 26-1/2 1 x 2497 Seat 5/4 x 6 x 29-1/2 2 x H10 1/4 x 2-1/4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 3 x S15 #8 x 1-3/4 Wood Screw 4 x S20 #8 x 1-3/8 Wood Screw 4 x S3 #8 x 2-1/2 Wood Screw 37 support@cedarsummitplay.com

38 Step 13: Cafe Seat Assembly Part 2 E: Attach 1 Corner Bracket to (2492) Front Top Bottom and to outside of (2495) Bench Support under the bolt with 2 (S5) #8 x 1/2 Pan Screws and 1 (S10) #8 x 1 Pan Screw as shown in fig and (S5) #8 x 1/2 Pan Screws installed into (2495) Bench Support. F: Attach 1 Corner Bracket flush to the top of (2492) Front Top Bottom and to inside of (2495) Bench Support with 2 (S5) #8 x 1/2 Pan Screws and 1 (S10) #8 x 1 Pan Screw as shown in fig and (S5) #8 x 1/2 Pan Screws installed into (2495) Bench Support. G: In the opening of (2526) Cafe Panel attach (2498) Cafe Top, tight to the corners of the panel opening, with 2 (S3) #8 x 2-1/2 Wood Screws as shown in fig S3 Tight Fig Tight Fig Corner Bracket Flush Fig S5 S5 S Corner Bracket S Wood Parts 1 x 2498 Cafe Top 5/4 x 4 x 24-1/4 4 x S5 #8 x 1/2 Pan Screw 2 x S10 #8 x 1 Pan Screw 2 x S3 #8 x 2-1/2 Wood Screw Other Parts 2 x Corner Bracket 38 support@cedarsummitplay.com

39 Step 14: Attach Rockwall Assembly and Rails Part 1 Pre-drill all holes using a 3/16 drill bit before installing the Wafer Lags. A: Place the Rockwall Assembly on the Back of the fort, flush to top of (2478) Floors and flush to inside edge of (2473) Post then attach to (2477) Back Floor Support with 1 (WL3) 1/4 x 1-3/8 Wafer Lag (with flat washer) in each Swing Bracket. (fig and 14.2). B: Place (2605) Access Board (from Step 2) tight to the top and edges of (2727) Rockwall Top and attach to (8139) Rock Rails with 4 (S20) #8 x 1-3/8 Wood Screws. (fig. 14.3) C: Make sure the edges of (2474) Ground SW and (2730) Rockwall Brace are flush then attach with 2 (S15) #8 x 1-3/4 Wood Screws. (fig and 14.4) Fig Flush Fig WL3 1/4 Flat 2477 Back S20 Fig x Fig S Flush 2 x WL3 1/4 x 1-3/8 Wafer Lag (1/4 flat washer) 4 x S20 #8 x 1-3/8 Wood Screw 2 x S15 #8 x 1-3/4 Wood Screw 39 support@cedarsummitplay.com

40 Step 14: Attach Rockwall Assembly and Rails Part 2 D: Place EN71 Hand Rail 1 from front edge of (2727) Rockwall Top and flush to the edge of (2603) Rock Board A. Pre-drill holes using a 3/16 drill bit then attach EN71 Hand Rail using 2 (S7) #12 x 2 Pan Screws. (fig and 14.6). Fig Fig S EN71Hand Rail S x S7 #12 x 2 Pan Screw Other Parts 1 x EN71 Hand Rail 40 support@cedarsummitplay.com

41 Step 15: Attach Bottom Windows A: From inside the assembly centre 1 (2736) Bottom Window under each window opening on the front wall, flush to the top of the bevelled edge then attach with 3 (S20) #8 x 1-3/8 Wood Screws per board. (fig and 15.2). Fig Front Fig Flush S20 Wood Parts 2 x 2736 Bottom Window 1 x 2 x 26 6 x S20 #8 x 1-3/8 Wood Screw 41 support@cedarsummitplay.com

42 Step 16: Crowsnest and Back Wall Assembly Part 1 A: In the opening of (2529) SL Side Panel attach (2483) SW Table Top, tight to the corners of the panel opening, ledge facing in, with 3 (S3) #8 x 2-1/2 Wood Screws as shown in fig and B: Attach 1 (2500) Crowsnest Post to (2475) FR Floor Support and (2477) Back Floor Support with 1 (H3) 1/4 x 2-1/2 Hex Bolt (with lock washer, flat washer and t-nut) per side. (fig and 16.3) C: Make sure the (2500) Crowsnest Posts are square then flush to the front and tight to the top of (2489) Floor End attach (2502) Crowsnest Floor End to both (2500) Crowsnest Posts with 2 (S4) #8 x 3 Wood Screws per post as shown in fig and D: Flush to the front and top of both (2500) Crowsnest Posts attach (2501) Crowsnest Top to posts with 2 (S4) #8 x 3 Wood Screws per post as shown in fig and Fig Fig S (hidden) /4 T-Nut (hidden) S4 H /4 Lock Slide SIde Tight 1/4 Flat 2477 S3 Tight and Flush (hidden) Fig Tight Note orientation, ledge faces inward Wood Parts 1 x 2483 SW Table Top 5/4 x 3 x 34-1/4 2 x 2500 Crowsnest Post 2 x 4 x 38-3/8 1 x 2502 Crowsnest Floor End 2 x 4 x 38-1/2 1 x 2501 Crowsnest Top 2 x 4 x 38-1/2 2 x H3 1/4 x 2-1/2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 8 x S4 #8 x 3 Wood Screw 3 x S3 #8 x 2-1/2 Wood Screw 42 support@cedarsummitplay.com

43 Step 16: Crowsnest and Back Wall Assembly Part 2 E: Flush to the top of the floor and flush to the end of (2500) Crowsnest Post attach 1 (2487) Crowsnest Bottom Front to (2500) Crowsnest Post and (2473) Post on the Back of the assembly and 1 (2487) Crowsnest Bottom Front to (2500) Crowsnest Post and (2527) Chalkwall Panel on the Front of the assembly with 4 (S7) #12 x 2 Pan Screws per board. (fig. 16.4, 16.5 and 16.6) F: Attach 1 (2488) Crowsnest Top Front flush to the top and end of each (2500) Crowsnest Post with 1 (H10) 1/4 x 2-1/4 Hex Bolt (with lock washer, flat washer and t-nut) per board. (fig. 16.4, 16.5 and 16.6) G: Make sure both (2488) Crowsnest Top Fronts are level then attach to each (2500) Crowsnest Post with 1 (S7) #12 x 2 Pan Screws per board and to (2473) Post and (2527) Chalkwall Panel with 2 (S7) #12 x 2 Pan Screws per board. (fig. 16.4, 16.5 and 16.6) Fig Front /4 T-Nut (hidden) Fig /4 Flat S7 x 3 Fig H H10 1/4 Lock Flush Back 2473 S7 x 3 S7 x Flush S7 x Flush to Floor Boards Wood Parts 2 x 2488 Crowsnest Top Front 5/4 x 5 x 15-5/8 2 x H10 1/4 x 2-1/4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 2 x 2487 Crowsnest Bottom Front 5/4 x 5 x 15-5/8 14 x S7 #12 x 2 Pan Screw 43 support@cedarsummitplay.com

44 Step 16: Crowsnest and Back Wall Assembly Part 3 H: Measure 1 down from the top of each (2488) Crowsnest Top Front and centred between (2500) Crowsnest Post and (2473) Post/(2527) Chalkwall Panel attach 1 (2503) Wall Board to each (2488) Crowsnest Top Front and each (2481) Lower Back with 4 (S20) #8 x 1-3/8 Wood Screws per board. (fig and 16.8) Fig Fig S20 x 4 per board 2487 Wood Parts 2 x 2503 Wall Board 1 x 5 x 32-1/2 8 x S20 #8 x 1-3/8 Wood Screw 44 support@cedarsummitplay.com

45 Step 16: Crowsnest and Back Wall Assembly Part 4 Pre-drill holes using a 1/8 drill bit before installing the (S20) #8 x 1-3/8 Wood Screws in (2494) Middle Back. I: Place (2733) Rockwall Post tight to the Rockwall Assembly and flush to the bottom of (2477) Back Floor Support. Top of (2733) Rockwall Post should be on the inside of (2494) Middle Back and the two boards should be square. Then attach to (2477) Back Floor Support with 2 (S3) #8 x 2-1/2 Wood Screws and to (2494) Middle Back in the pre-drilled holes with 2 (S20) #8 x 1-3/8 Wood Screws. (fig and 16.10) J: In between (2733) Rockwall Post and (2482) Back Wall Support place (2739) Spacer A flush to the top of (2477) Back Floor. Notice the 2 holes are at the top and 1 at the bottom of the board. Attach with 3 (S20) #8 x 1-3/8 Wood Screws. (fig and 16.10) K: In between (2473) Post and (2482) Back Wall Support place (2740) Spacer B flush to the top of the floor boards. Notice the 2 holes are at the top and 1 at the bottom of the board. Attach with 3 (S20) #8 x 1-3/8 Wood Screws. (fig and 16.10) Fig S Fig Rockwall Assembly S Flush and tight S20 Flush to Back Floor Notice holes in Spacer A and Spacer B, 2 holes on top and 1 on the bottom 2739 S (hidden) 2740 Wood Parts 1 x 2733 Rockwall Post 2 x 3 x 32 1 x 2739 Spacer A 1 x 4 x 10-5/8 1 x 2740 Spacer B 1 x 4 x 14 8 x S20 #8 x 1-3/8 Wood Screw 2 x S3 #8 x 2-1/2 Wood Screw 45 support@cedarsummitplay.com

46 Step 16: Crowsnest and Back Wall Assembly Part 5 L: Place 2 (1975) Cedar Walls evenly spaced between (2733) Rockwall Post and (2482) Back Wall Support. The bottom of the boards should be on the outside of the assembly and the tops should be on the inside of the assembly and 1 down from the top of (2494) Middle Back. Attach (1975) Cedar Walls to (2482) Middle Back with 2 (S1) #8 x 1-1/8 Wood Screws per board and to (2739) Spacer A with 2 (S20) #8 x 1-3/8 Wood Screws per board. (fig , and 16.13) Fig Fig Inside View S1 x 2 per board on top Fig Outside View S20 x 2 per board on 2739 bottom Wood Parts 2 x 1975 Cedar Wall 1 x 4 x 29 4 x S20 #8 x 1-3/8 Wood Screw 4 x S1 #8 x 1-1/8 Wood Screw 46 support@cedarsummitplay.com

47 Step 16: Crowsnest and Back Wall Assembly Part 6 M: From inside the assembly attach 1 (2341) Crowsnest Upright to each end of (2501) Crowsnest Top and (2489) Crowsnest Floor End with 2 (H3) 1/4 x 2-1/2 Hex Bolts (with lock washer, flat washer and t-nut) per board. (fig , and 16.16) N: From inside the assembly, flush to top of (2501) Crowsnest Top, in between both (2341) Crowsnest Uprights, attach 1 (2337) Crowsnest Back with 6 (S15) #8 x 1-3/4 Wood Screws. (fig and 16.15) O: From outside the assembly, flush to the inside of both (2341) Crowsnest Uprights place 1 (2338) Crowsnest Face on each board and attach from inside the assembly with 3 (S15) #8 x 1-3/4 Wood Screws per board. (fig and 16.16) H3 1/4 Lock Fig Inside View Fig /4 Flat /4 T-Nut S15 x H Fig Outside View S x 3 per board 2341 Flush 2489 H3 Wood Parts 2 x 2341 Crowsnest Upright 5/4 x 4 x 34-3/8 1 x 2337 Crowsnest Back 5/4 x 4 x 25-1/2 2 x 2338 Crowsnest Face 2 x 4 x 27-1/2 4 x H3 1/4 x 2-1/2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 12 x S15 #8 x 1-3/4 Wood Screw 47 support@cedarsummitplay.com

48 Step 16: Crowsnest and Back Wall Assembly Part 7 P: Centre 3 (2340) Crowsnest Joists over the pilot holes in (2337) Crowsnest Back so the 2 outside (2340) Crowsnest Joists are flush to the outside edges of (2337) Crowsnest Back, then attach with 6 (S3) #8 x 2-1/2 Wood Screws. (fig ) Q: Measure 3/16 from the front of (2337) Crowsnest Back attach 1 (2339) Crowsnest Floor flush to the outside edges with 5 (S20) #8 x 1-3/8 Wood Screws. (fig ) R: Place the floor assembly just created in between both (2341) Crowsnest Uprights, flush to the top and tight to (2489) Crowsnest Floor End. (2339) Crowsnest Floor is at the back of the assembly. Attach floor assembly to (2489) Crowsnest Floor End with 6 (S4) #8 x 3 Wood Screws. (fig and 16.19) S: Place (2738) Crowsnest Floor Board, in between (2339) Crowsnest Floor and (2489) Crowsnest Floor End so the notches fit around the (2341) Crowsnest Uprights then attach with 5 (S20) #8 x 1-3/8 Wood Screws. Notice the orientation of (2738) Crowsnest Floor Board. (fig and 16.19) Fig S20 x 5 3/16 Fig S3 x Notice board orientation Flush S20 x Fig Centre in opening 2738 S4 x 6 Tight 2489 Wood Parts 3 x 2340 Crowsnest Joist 2 x 4 x 8-5/8 1 x 2337 Crowsnest Back 5/4 x 4 x 25-1/2 1 x 2339 Crowsnest Floor 1 x 6 x 25-3/8 1 x 2738 Crowsnest Floor Board 5/8 x 5-1/4 x 31-1/2 10 x S20 #8 x 1-3/8 Wood Screw 6 x S3 #8 x 2-1/2 Wood Screw 6 x S4 #8 x 3 Wood Screw 48 support@cedarsummitplay.com

49 Step 17: Roof Support Assembly Part 1 A: Attach (2518) Roof Support Right to (2499) Roof Support Left at peak using 1 (S4) #8 x 3 Wood Screw. (fig. 17.1) B: Repeat Step A to create a second Roof Support Assembly. (fig. 17.1) C: On one of the assemblies attach (8611) Gable Bottom to (2518) Roof Support Right to (2499) Roof Support Left with 2 (H10) 1/4 x 2-1/4 Hex Bolts (with lock washer, flat washer and t-nut). (fig. 17.2) Fig S Fig S H10 (hidden) H10 1/4 Lock 1/4 Flat 1/4 T-Nut 8611 Wood Parts 2 x 2518 Roof Support Right 5/4 x 4 x 34 2 x 2499 Roof Support Left 5/4 x 4 x 34 1 x 8611 Gable Bottom 2 x 4 x 41 2 x S4 #8 x 3 Wood Screw 2 x H10 1/4 x 2-1/4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 49 support@cedarsummitplay.com

50 Step 17: Roof Support Assembly Part 2 D: Place Roof Support Assembly with (8611) Gable Bottom on the Slide Side so the (8611) Gable Bottom sits on top of (2527) Chalkwall Panel and (2473) Post. The supports are flush to the ends of (2527) Chalkwall Panel and (2473) Post then attach with 1 (S3) #8 x 2-1/2 Wood Screw per side from outside the fort. (fig. 17.3, 17.4 and 17.5) E: From inside the assembly attach Roof Support Assembly with (8611) Gable Bottom to (2527) Chalkwall Panel and (2473) Post using 1 Corner Bracket with 3 (S5) #8 x 1/2 Pan Screws per side. (fig. 17.3, 17.4 and 17.5) F: Place remaining Roof Support Assembly tight to the tops of (2521) SW Side Posts and attach with 1 (H10) 1/4 x 2-1/4 Hex Bolt (with lock washer, flat washer and t-nut) and 1 (S3) #8 x 2-1/2 Wood Screw per side. (fig and 17.6) Fig Tight Fig S x 2 per side Slide Side S5 x 3 per bracket Corner Bracket (1 per side) /4 T-Nut (hidden) 1/4 Lock Fig /4 Flat 2499 H10 (1 per side) Tight 2527 Fig Swing Side 4 x S3 #8 x 2-1/2 Wood Screw 6 x S5 #8 x 1/2 Pan Screw Other Parts 2 x Corner Bracket 2 x H10 1/4 x 2-1/4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 50 support@cedarsummitplay.com

51 Step 18: Roof Assembly Part 1 A: Connect 1 (2525) Roof Panel to a second (2525) Roof Panel so the one panel overlaps the other and the inside angle is square and tight. Attach panels together with 5 (S15) #8 x 1-3/4 Wood Screws per panel. (fig and 18.2) Fig S15 x 5 per side Fig Notice overlap is flush. Wood Parts 2 x 2525 Roof Panel 1-1/4 x 35-7/16 x x S15 #8 x 1-3/4 Wood Screw 51 support@cedarsummitplay.com

52 Step 18: Roof Assembly Part 2 B: On the inside of the Roof Assembly on 1 (2525) Roof Panel, on the 5th siding down, measure 3/4 in from the edge of the middle slat and pre-drill 2 holes with a 3/16 drill bit as shown in fig and This will now be referred to as the front of the Roof Assembly. C: On the outside of the Roof Assembly place (8069) Dormer Cleat over the pre-drilled holes and from inside the assembly attach with 2 (S7) #12 x 2 Pan Screws (with flat washer). (fig and 18.5) Fig Fig /4 5th Siding S Inside View 3/16 Flat Fig Front Wood Parts 1 x 8069 Dormer Cleat 2 x 4 x 10 2 x S7 #12 x 2 Pan Screw (3/16 flat washer) 52 support@cedarsummitplay.com

53 Step 18: Roof Assembly Part 3 D: Lay 2 (8070) Dormer Sides flat on the ground so the tops are tight together and form a peak. The side facing up will be the back. (fig and 18.7) E: Tight to the bottom of both (8070) Dormer Sides place (8073) Dormer Bottom so the outside edges are flush. (fig and 18.7) F: On the front of the assembly, centred on top of (8073) Dormer Bottom, place (8074) Dormer Burst. (fig and 18.7) G: Place (8071) Dormer Centre on the back side, flush to the bottom of (8073) Dormer Bottom so the tip is centred at the peak of the (8070) Dormer Sides then attach with 4 (S1) #8 x 1-1/8 Wood Screws. (fig. 18.7) H: Place 1 (8072) Dormer Side Burst tight to each side of (8071) Dormer Centre so they are flush to the bottom of (8073) Dormer Bottom then attach with 2 (S1) #8 x 1-1/8 Wood Screws per board. (fig. 18.7) Fig Tight Flush Flush Flush 8071 Fig Front View Flush Flush Flush 8072 Flush Back View Flush S Wood Parts 2 x 8070 Dormer Side 1 x 3 x 13-5/8 1 x 8073 Dormer Bottom 1 x 2 x 22 1 x 8074 Dormer Burst 1 x 4 x 5-1/2 1 x 8071 Dormer Centre 1 x 3 x 10-3/4 2 x 8072 Dormer Side Burst 1 x 3 x 6-3/4 8 x S1 #8 x 1-1/8 Wood Screw 53 support@cedarsummitplay.com

54 Step 18: Roof Assembly Part 4 I: Attach Dormer Roof Right to Dormer Roof Left, from (8068) Dormer Roof Set at the inside peak with 1 Wall Angle Bracket using 2 (S5) #8 x 1/2 Pan Screws. (fig. 18.8) J: Place the Dormer Burst Assembly from Step 17, Part 3 on the inside edge of each Dormer Roof and attach with 6 (S1) #8 x 1-1/8 Wood Screws. (fig. 18.8) K: Place completed Dormer Assembly over (8069) Dormer Cleat and attach with 2 (S3) #8 x 2-1/2 Wood Screws (fig. 18.9) Fig Wall Angle Bracket Dormer Roof Right S5 Dormer Roof Left S1 Dormer Burst Assembly S (hidden) S3 Fig Front Wood Parts 1 x 8068 Dormer Roof Set Includes: 1 x Dormer Roof Right 1 x Dormer Roof Left 6 x S1 #8 x 1-1/8 Wood Screw 2 x S5 #8 x 1/2 Pan Screw 2 x S3 #8 x 2-1/2 Wood Screw Other Parts 1 x Wall Angle Bracket 54 support@cedarsummitplay.com

55 Step 19: Attach Roof Assembly to Fort A: With 2 people on the ground and at least 1 person in the fort, lift the Roof Assembly from Step 17, up and over the fort. The Dormer Assembly should be on the front of the assembly. Guide the Roof Assembly onto the fort so it is centred over the Roof Support Assemblies then attach with 4 (S3) #8 x 2-1/2 Wood Screws per (2525) Roof Panel, 1 screw in each corner. (fig. 19.1) S3 x 8 Fig Roof Support Assembly (hidden) 2525 Roof Support Assembly Front 8 x S3 #8 x 2-1/2 Wood Screw 55 support@cedarsummitplay.com

56 Step 20: Attach Gable Boards to Fort A: Centre (8614) Sunburst lengthway on the outside of (8611) Gable Bottom then measure 1-1/4 up from the bottom of (8611) Gable Bottom and attach (8614) Sunburst with 2 (S15) #8 x 1-3/4 Wood Screws. (fig and 20.2) B: On the inside of the assembly place (8612) Centre Gable Board tight to the top of (8611) Gable Bottom so the tip is centred at the peak of the Roof Support Assembly then attach to (2518) Roof Support Right, (2499) Roof Support Left and (8614) Sunburst with 4 (S20) #8 x 1-3/8 Wood Screws. (fig and 20.3) C: Place 1 (8613) Gable Board A tight to each side of (8612) Centre Gable Board and tight to the top of (8611) Gable Bottom then attach to (2518) Roof Support Right, (2499) Roof Support Left and (8614) Sunburst with 3 (S20) #8 x 1-3/8 Wood Screws per board. (fig and 20.3) Fig Fig /4 S15 Front View 8612 Fig Slide Side Tight Inside View S20 x 10 Wood Parts 1 x 8614 Sunburst 5/4 x 6 x 10 1 x 8612 Centre Gable Board 1 x 4 x 16-1/8 2 x 8613 Gable Board A 1 x 4 x 10-15/16 2 x S15 #8 x 1-3/4 Wood Screw 10 x S20 #8 x 1-3/8 Wood Screw 56 support@cedarsummitplay.com

57 Step 21: Install Ground Stakes MOVE FORT TO FINAL LOCATION PRIOR TO STAKING FINAL LOCATION MUST BE LEVEL GROUND A: Drive 1 (0318) Ground Stake 10-1/2 into the ground at (2491) Diagonal, at end of (2474) Ground SW at back of fort, on (8168) SL Support and on (2529) SL Side Panel at front of fort as shown in fig Attach using 2 (S3) #8 x 2-1/2 Wood Screws per ground stake. (fig. 21.2) WARNING: To prevent tipping and avoid potential injury, stakes must be driven 10-1/2 into ground. Digging or driving stakes can be dangerous if you do not check first for underground wiring, cables or gas lines. Fig Fig S Front /2 Into Ground 0318 Wood Parts 4 x 0318 Ground Stake 1-1/4 x 1-1/2 x 14 8 x S3 #8 x 2-1/2 Wood Screw 57 support@cedarsummitplay.com

58 Step 22: Swing Beam Assembly Fig A: In the middle holes of (1249) Back Beam install 2 Bolt-Thru Swing Hangers (fig. 22.1) making sure the swing hangers are oriented in the direction shown in fig to maintain proper swing motion. Make sure triangle is tight against beam WARNING: For your child s safety, orientate the swing hangers as shown to ensure your swing will have proper swing motion when installed. Failure to do so could result in premature failure of the swing hanger or swing chain. B: In the end holes of (1248) Front Beam install 2 Bolt-Thru Swing Hangers (fig. 22.1) making sure the swing hangers are oriented in the direction shown in fig to maintain proper swing motion. Bolt-Thru Swing Hangers 1249 Bolt-Thru Swing Hangers Fig Make sure holes are aligned C: Attach 1 Triangle Plate to the ends of each (1248) Front Beam and (1249) Back Beam using 1 (G1) 5/16 x 1-1/2 Hex Bolt (with lock washer, flat washer and t-nut) per triangle plate in the hole indicated in fig Correct hole usage is very important. D: Attach 1 (H7) 1/4 x 5-1/2 Hex Bolt (with lock washer, flat washer and t-nut) to the ends of each (1248) Front Beam and (1249) Back Beam. The bolts do not attach to anything, but MUST be installed to the beams to prevent splitting and checking of wood. (fig. 22.2) Triangle Plate H7 Fig Important! Fort End Side (No Overhang) 1/4 Flat 1/4 Lock H7 G1 5/16 Flat 5/16 Lock G1 H7 Triangle Plate H7 Triangle Plate 1/4 T-Nut Important! Swing End (With Overhang) Triangle Plate /16 T-Nut Wood Parts Other Parts 1 x 1248 Front Beam 2 x 6 x 94 4 x H7 1/4 x 5-1/2 Hex Bolt 1 x Bolt-Thru Swing Hangers (pkg of 4) (1/4 flat washer, 1/4 lock washer, 1/4 t-nut) 1 x 1249 Back Beam 2 x 6 x 94 1 x Triangle Plate (pkg of 4) 4 x G1 5/16 x 1-1/2 Hex Bolt (5/16 flat washer, 5/16 lock washer, 5/16 t-nut) 58 support@cedarsummitplay.com

59 Step 23: Swing End Assembly A: Attach 2 (2471) Heavy SW Posts to (1856) SW Upright using 2 (G4) 5/16 x 4 Hex Bolts (with lock washer, flat washer and t-nut). (fig. 23.1) Fig /16 T-Nut /16 T-Nut 5/16 Flat 5/16 Lock 5/16 Flat G6 5/16 Lock G B: Attach (2472) Heavy SW Support to both (2471) Heavy SW Posts and (1856) SW Upright using 3 (G6) 5/16 x 4-3/4 Hex Bolts (with lock washer, flat washer and t-nut). (fig. 23.1) Wood Parts 2 x 2471 Heavy SW Post 2 x 3-3/8 x 86-11/16 1 x 2472 Heavy SW Support 2 x 4 x 46-1/2 1 x 1856 SW Upright 2 x 4 x 48-5/16 2 x G4 5/16 x 4 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 3 x G6 5/16 x 4-3/4 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 59 support@cedarsummitplay.com

60 Step 24: Attach Swing End to Swing Beam A: Place (4919) SW Rail Block in the centre between (1248) Front Beam and (1249) Back Beam and attach with 1 (H8) 1/4 x 4-1/4 Hex Bolt (with lock washer, flat washer and t-nut). (fig & 24.2) Fig H8 Glider Hangers WARNING: Glider Hangers must be tight and secure to Swing Beams. 1/4 Lock 1/4 Flat Fig /4 T-Nut 1249 B: Attach Swing End Assembly to the side of the Swing Beam Assembly with the overhang (fig & 24.4) using 1 (G5) 5/16 x 4-1/2 Hex Bolt (with lock washer, flat washer and t-nut) in the top hole of Triangle Plate and 1 (G8) 5/16 x 2 Hex Bolt (with 2 flat washers and lock nut) in the bottom hole of Triangle Plate. (fig. 24.3) Make sure Swing End Assembly flares out at an angle. (fig. 24.4) C: Attach 2 Glider Hangers to the Swing Beam Assembly using 2 (G7) 5/16 x 5-1/2 Hex Bolt (with 2 flat washers & lock nut) per Glider Hanger. (fig & 24.3) Fig Side with overhang Fig G8 5/16 Lock G5 5/16 Flat 5/16 Lock Nut 5/16 Flat 5/16 Flat 100 5/16 Lock Nut 5/16 T-Nut G7 Wood Parts 1 x 4919 SW Rail Block 2 x 4 x 5-3/8 1 x H8 1/4 x 4-1/4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 1 x G5 5/16 x 4-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 4 x G7 5/16 x 5-1/2 Hex Bolt (5/16 flat washer x 2, 5/16 lock nut) 1 x G8 5/16 x 2 Hex Bolt (5/16 flat washer x 2, 5/16 lock nut) Other Parts 2 x Glider Hanger 60 support@cedarsummitplay.com

61 Step 25: Attach Swing Assembly to Fort A: Attach Swing Assembly from Step 24 to (2486) SW Mount with 1 (G5) 5/16 x 4-1/2 Hex Bolt (with lock washer, flat washer and t-nut) and 1 (G8) 5/16 x 2 Hex Bolt (with 2 flat washers and 1 lock nut) as shown in fig and B: Drive 1 (0318) Ground Stake 10-1/2 into the ground at each (2471) Heavy SW Post on the inside of the assembly and attach with 2 (S3) #8 x 2-1/2 Wood Screws per ground stake. (fig and 25.3) WARNING: To prevent tipping and avoid potential injury, stakes must be driven 10-1/2 into ground. Digging or driving stakes can be dangerous if you do not check first for underground wiring, cables or gas lines. 5/16 T- Nut Fig /16 Flat 5/16 Lock G5 Fig /16 Lock nut 5/16 Flat 2486 G Fig S3 10-1/2 Into Ground 0318 Wood Parts 2 x 0318 Ground Stake 1-1/4 x 1-1/2 x 14 4 x #8 x 2-1/2 Wood Screw S3 1 x G5 5/16 x 4-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 1 x G8 5/16 x 2 Hex Bolt (5/16 flat washer x 2, 5/16 lock nut) 61 support@cedarsummitplay.com

62 Step 26: Side Nest Assembly Part 1 A: Loosely attach 1 (2507) Side Nest Top to the top of 2 (2511) Nest Posts with 4 (H10) 1/4 x 2-1/4 Hex Bolts (with lock washer, flat washer and t-nut). Notice hole locations at edges of (2511) Nest Posts. (fig. 26.1) B: On the opposite side of (2511) Nest Posts loosely attach 1 (2510) Floor Support to the bottom of both (2511) Nest Posts with the extension on the right side, with 4 (H3) 1/4 x 2-1/2 Hex Bolts (with lock washer, flat washer and t-nut). (fig. 26.1) C: Make sure the assembly is square then tighten all bolts. (fig. 26.1) D: Flush to the top of (2510) Floor Support and outside edge of left (2511) Nest Post attach (2509) Lower Side to both posts with 4 (S7) #12 x 2 Pan Screws. (fig. 26.1) E: Flush to the extended end of (2510) Floor Support attach 1 Swing Bracket using 1 (G1) 5/16 x 1-1/2 Hex Bolt (with lock washer, flat washer and t-nut). Flat edge faces out. (fig. 26.1) F: Repeat Steps A-E to create a second Side Nest End Assembly, opposite of the first. (fig. 26.2) Fig Fig /4 T-Nut 1/4 Flat 1/4 Lock H10 Notice hole location H Flush 2511 Flush S /16 Lock 2509 S7 5/16 Flat H3 G H3 H3 S7 Swing 5/16 Bracket T-Nut Flush Flush S7 H Wood Parts 2 x 2507 Side Nest Top 5/4 x 4 x 33-7/8 4 x 2511 Nest Post 2 x 3 x 37-5/8 2 x 2510 Floor Support 2 x 4 x 38 2 x 2509 Lower Side 5/4 x 4 x 39-1/4 8 x S7 #12 x 2 Pan Screw 8 x H10 1/4 x 2-1/4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 8 x H3 1/4 x 2-1/2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 2 x G1 5/16 x 1-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) Other Parts 2 x Swing Bracket 62 support@cedarsummitplay.com

63 Step 26: Side Nest Assembly Part 2 G: Stand both Side Nest End Assemblies with the extensions facing the same way and the Swing Brackets facing in. Loosely attach (2505) Top End Nest to the top of both (2511) Nest Posts on the extended side with 2 (H12) 1/4 x 3 Hex Bolts (with lock washer, flat washer and t-nut). (fig. 26.3) H: Loosely attach (2520) End Nest Top to the top of both (2511) Nest Posts, on the opposite side with 2 (H13) 1/4 x 3-1/2 Hex Bolts (with lock washer, flat washer and t-nut). (fig. 26.3) I: Make sure the assembly is square then tighten all bolts. (fig. 26.3) J: Flush to the top of both (2509) Lower Sides attach (2506) Bottom Nest End to both (2511) Nest Posts with 4 (S7) #12 x 2 Pan Screws. (fig. 26.3) H12 1/4 T-Nut 1/4 Flat Fig /4 Lock H13 H S7 Flush Wood Parts 1 x 2505 Top End Nest 1 x 4 x 29-3/4 1 x 2520 End Nest Top 5/4 x 4 x 29-3/4 1 x 2506 Bottom Nest End 5/4 x 4 x 29-3/4 4 x S7 #12 x 2 Pan Screw 2 x H12 1/4 x 3 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 2 x H13 1/4 x 3-1/2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 63 support@cedarsummitplay.com

64 Step 27: Attach Side Nest to Fort A: Make sure the Swing Assembly is perpendicular to the fort and level. (fig. 27.1) B: With at least 1 helper lift Side Nest Assembly onto Swing Assembly with the extended end towards the fort. (fig and 27.2) C: Pre-drill with a 1/8 drill bit in (2505) Top End Nest and into edge of the (2525) Roof Panels as shown in fig and Attach with 2 (S15) #8 x 1-3/4 Wood Screws. D: Make sure both (2509) Lower Sides are flush to the inside edge of (2521) SW Side Post and tight to top of (2528) SW Wall Panel then attach each (2509) Lower Side to the (2521) SW Side Posts with 2 (S15) #8 x 1-3/4 Wood Screws per board. (fig and 27.4) E: Pre-drill with a 1/8 drill bit then attach Swing Brackets to (2528) SW Wall Panel with 1 (WL3) 1/4 x 1-3/8 Wafer Lag (with 1/4 flat washer). (fig and 27.4) Fig Fig Fig S15 Fig S15 Swing Bracket 1/4 Flat WL x S15 #8 x 1-3/4 Wood Screw 2 x WL3 1/4 x 1-3/8 Wafer Lag (1/4 flat washer) 64 support@cedarsummitplay.com

65 Step 28: Attach Side Nest Gussets Part 1 A: Attach 1 (2512) End Nest Board to 1 (2513) Gusset with 2 (H10) 1/4 x 2-1/4 Hex Bolts (with lock washer, flat washer and t-nut) as shown in fig The edge of (2512) End Nest Board without the pilot holes to be flush to the bottom edge of (2513) Gusset. (fig. 28.1) B: Repeat Step A to create a second Gusset Assembly, opposite to the first. (fig. 28.2) 1/4 T-Nut Fig Notice hole location Fig /4 Flat 1/4 Lock Flush 2512 H10 Notice hole location H Wood Parts 2 x 2512 End Nest Board 5/4 x 4 x 11-1/4 2 x 2513 Gusset 2 x 4 x 9 4 x H10 1/4 x 2-1/4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 65 support@cedarsummitplay.com

66 Step 28: Attach Side Nest Gussets Part 2 C: Place 1 Gusset Assembly tight to (1248) Front Beam and bottom of (2506) Bottom Nest End and attach (2512) End Nest Board to (2510) Floor Support with 2 (S7) #12 x 2 Pan Screws. (fig and 28.4) D: Pre-drill with a 1/8 drill bit then attach (2513) Gusset to (1248) Front Beam with 1 (LS2) 1/4 x 2-1/2 Lag Screw (with 1/4 flat washer) (fig. 28.4) E: Repeat Steps C and D on (1249) Back Beam. (fig and 28.4) S7 Fig Fig Tight 1248 LS2 1/4 Flat 4 x S7 #12 x 2 Pan Screw 2 x LS2 1/4 x 2-1/2 Lag Screw (1/4 flat washer) 66 support@cedarsummitplay.com

67 Step 29: Attach Short Rails A: Place 1 (2508) Short Rail flush to the inside ends of each (2511) Nest Post closest to the fort. The top of the (2508) Short Rails must be tight to the (2499) and (2518) Roof Supports. Attach each (2508) Short Rail to each (2511) Nest Post with 2 (S7) #12 x 2 Pan Screws per board. (fig and 29.2) B: Attach the (2508) Short Rails to each (2521) SW Side Post with 2 (S15) #8 x 1-3/4 Wood Screws per board. (fig and 29.2) 2511 Tight Fig Tight S S S Flush Flush S Fig Wood Parts 2 x 2508 Short Rail 5/4 x 4 x 7-3/4 4 x S15 #8 x 1-3/4 Wood Screw 4 x S7 #12 x 2 Pan Screw 67 support@cedarsummitplay.com

68 Step 30: Attach Side Nest Floor Boards A: Place 1 (2514) Floor Board on both (2510) Floor Supports tight to (2506) Bottom Nest End then follow with 8 more (2514) Floor Boards. The last board should sit flush to the inside edge of (2528) SW Wall Panel. Make sure boards are evenly spaced then attach with 6 (S20) #8 x 1-3/8 Wood Screws per board. (fig and 30.2) Fig Tight 2509 S20 x 6 per board 2510 (hidden) Flush x 9, evenly spaced Fig Wood Parts 9 x 2514 Floor Board 1 x 5 x x S20 #8 x 1-3/8 Wood Screw 68 support@cedarsummitplay.com

69 Step 31: Attach Spindles to Fort Part 1 A: Centre 1 (2517) Spindle between edge of (2509) Lower Side and inside edge of (2511) Nest Post then attach to (2508) Short Rail and (2509) Lower Side with 2 (S15) #8 x 1-3/4 Wood Screws. (fig and 31.2) B: Repeat Step A for other side of Side Nest. (fig and 31.2) Fig Fig S Wood Parts 2 x 2517 Spindle 5/4 x 2 x 17 4 x S15 #8 x 1-3/4 Wood Screw 69 support@cedarsummitplay.com

70 Step 31: Attach Spindles to Fort Part 2 C: Between (2511) Nest Posts on the front of the assembly evenly space and attach 7 (2515) Long Spindles to (2509) Lower Side and flush to top of (2507) Side Nest Top with 2 (S15) #8 x 1-3/4 Wood Screws per board. Repeat for back of the assembly. (fig and 31.4) D: Evenly space and attach 6 (2515) Long Spindles to (2506) Bottom Nest End and flush to top of (2520) End Nest Top with 2 (S15) #8 x 1-3/4 Wood Screws per board. (fig and 31.4) 2507 Fig S15 x 2 per spindle 2515 x 7, evenly spaced Flush Fig Back x 7, evenly spaced x 6, evenly spaced Front Wood Parts 20 x 2515 Long Spindle 5/4 x 2 x x S15 #8 x 1-3/4 Wood Screw 70 support@cedarsummitplay.com

71 Step 32: Access Ladder Assembly Part 1 A: Place 2 (2737) Ladder Steps on 2 (2516) SW Nest Access Post, grooves facing down. Notice the orientation of the angles on the (2516) SW Nest Access Posts. Loosely attach with 2 (H11) 1/4 x 2-3/4 Hex Bolts (with lock washer, flat washer and t-nut) per post. (fig. 32.1) B: Make sure assembly is square then tighten the bolts. (fig. 32.1) H11 Fig Notice orientation of angles 1/4 Lock 1/4 Flat Grooves face down /4 T-Nut Wood Parts 2 x 2737 Ladder Step 1-3/8 x 1-3/4 x 13-3/4 2 x 2516 SW Nest Access Post 2 x 3 x 25 4 x H11 1/4 x 2-3/4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 71 support@cedarsummitplay.com

72 Step 32: Access Ladder Assembly Part 2 C: On the outside of the assembly on (2528) SW Wall Panel remove the 6 screws shown in fig D: On the inside of the assembly place the Access Ladder Assembly tight against the slats on (2528) SW Wall Panel and tight to (2478) Floor. The angled edges of the (2516) SW Nest Access Post face up and out. Attach from outside of the assembly in the same holes the screws were removed from with 6 (S7) #12 x 2 Pan Screws (with 3/16 flat washer). (fig. 32.2, 32.3 and 32.4) Fig Notice orientation of angles Fig Flush 2478 Front Inside View Outside View S7 x 6 with 3/16 Flat Fig Tight x S7 #12 x 2 Pan Screw (3/16 flat washer) 72 support@cedarsummitplay.com

73 Step 33: Attach Gable Boards A: From the inside of the Roof Assembly on the Swing Side, tight to the (2525) Roof Panels, attach (2522) Gable A to (2518) Roof Support Right and (2499) Roof Support Left with 4 (S20) #8 x 1-3/8 Wood Screws. (fig and 33.2) B: Tight to the bottom of (2522) Gable A place (2523) Lower Gable and pre-drill 2 holes from outside the assembly, 1-1/2 from the top of (2523) Lower Gable, and 2 holes 2 down from the first pilot holes, centred on (2499) and (2518) Roof Supports, with a 3/16 drill bit then attach to roof supports from outside the assembly with 4 (S7) #12 x 2 Pan Screws. (fig and 33.3) Parts removed for clarity Tight 2522 S20 x 4 Tight Fig Fig Inside View Fig Swing Side 1-1/2 2 S S7 Outside View Wood Parts 1 x 2522 Gable A 1 x 6 x 21 1 x 2523 Lower Gable 2 x 6 x 31-3/4 4 x S7 #12 x 2 Pan Screw 4 x S20 #8 x 1-3/8 Wood Screw 73 support@cedarsummitplay.com

74 Step 34: Attach Hand Grips A: Attach 1 Hand Grip to each (2519) SW Nest Wall with 2 (PB6) 1/4 x 1 Pan Bolt (with lock washer, flat washer and t-nut) as shown in fig B: Tight to the (2525) Roof Boards and tight to each side of (2523) Lower Gable attach both (2519) SW Nest Walls with 4 (S20) #8 x 1-3/8 Wood Screws per board as shown in fig and C: Measure 6 up from the floor boards on both (2473) Post and (2482) Back Wall Support, pre-drill with a 3/16 drill bit then attach 1 Hand Grip per board with 2 (WL3) 1/4 x 1-3/8 Wafer Lags (with flat washer) per Hand Grip. (fig and 34.3) Fig /4 T-Nut 1/4 Flat 1/4 Lock Fig S20 x 4 per board Tight 2525 Tight 2525 Tight PB6 PB Hand Grip WL3 Hand Grip Fig Hand Grip Floor Boards WL3 1/4 Flat Inside View Wood Parts 2 x 2519 SW Nest Wall 1 x 6 x 31 8 x S20 #8 x 1-3/8 Wood Screws 4 x PB6 1/4 x 1 Pan Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 4 x WL3 1/4 x 1-3/8 Wafer Lag (1/4 flat washer) Other Parts 4 x Hand Grip 74 support@cedarsummitplay.com

75 Step 35: Attach Telescope A: On the front outer corner of the Side Nest Assembly pre-drill with a 1/8 drill bit then attach Telescope to (2507) Side Nest Top and (2520) End Nest Top with 2 (S15) #8 x 1-3/4 Wood Screws. (fig and 35.2) S15 Fig Telescope 2520 Fig Front 2 x S15 #8 x 1-3/4 Wood Screw Other Parts 1 x Telescope 75 support@cedarsummitplay.com

76 Step 36: Slide Section Assemblies Part 1 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. (fig. 36.3) A: Fit 2 TNR2 Slide Elbows together and attach with 8 (PB1) 1/4 x 3/4 Pan Bolts (with lock nut) as shown in fig It is very important to attach bolts as indicated. B: Repeat Step A 3 more times to create 4 Elbow Sections in total. C: Attach TNR2 Slide RT Flange and TNR2 Slide LT Flange together using 4 (PB1) 1/4 x 3/4 Pan Bolts (with lock nut) as shown in fig This creates the Flange Assembly. Fig Lock Nut TNR2 Slide Elbow Fig Flange Assembly Lock Nut TNR2 Slide LT Flange PB1 TNR2 Slide RT Flange TNR2 Slide Elbow PB1 Lock Nut Fig PB1 PB1 Lock Nut Use a 7/16 open end wrench for nuts 36 x PB1 1/4 x 3/4 Pan Bolt (1/4 lock nut) Other Parts 1 x TNR2 Slide LT Flange 1 x TNR2 Slide RT Flange 8 x TNR2 Slide Elbow 76 support@cedarsummitplay.com

77 Step 36: Slide Section Assemblies Part 2 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. (fig. 36.3) D: Attach TNR2 Slide Exit Top and the remaining TNR2 Slide Elbow together using 8 (PB1) 1/4 x 3/4 Pan Bolts (with lock nut) as shown in fig It is very important to attach bolts as indicated. This creates the Exit Elbow Assembly. Fig TNR2 Slide Exit Top PB1 Lock Nut PB1 Lock Nut TNR2 Slide Elbow PB1 Fig PB1 Lock Nut 8 x PB1 1/4 x 3/4 Pan Bolt (1/4 lock nut) Other Parts 1 x TNR2 Slide Exit Top 1 x TNR2 Slide Elbow 77 support@cedarsummitplay.com

78 Step 37: Attach Flange Assembly to Fort A: With a helper place the Flange Assembly flush to the Crowsnest on the fort as shown in fig. 37.1, then pre-drill 1/8 pilot holes in the bottom 4 mounting locations on (2502) Crowsnest Floor End (approximate spots where circles are on figure), making sure the pre-drilled holes are a minimum of 1 deep. B: Attach Flange Assembly to the Crowsnest into (2502) Crowsnest Floor End using 4 (S7) #12 x 2 Pan Screws (with #12 Screw Bezel) in the pre-drilled holes. (fig and 37.2) Make sure the flat surfaces of the Flange Assembly are flush to the Crowsnest. C: Attach the Flange Assembly flush to (2501) Crowsnest Top using 4 (S6) #12 x 1 Pan Screws (with #12 Screw Bezel) as shown in fig and 37.3 and to both (2338) Crowsnest Faces using 5 (S6) #12 x 1 Pan Screws per board. (fig. 37.1, 37.4 and 37.5) Fig Flange Assembly 2501 S6 Top Fig #12 Screw Bezel 2338 (hidden) Top of slide flush to (2501) Crowsnest Top 2501 Fig S Sides Fig Outside View Bottom of slide flush with (2502) Crowsnest Floor End (hidden) S7 Fig Inside View #12 Screw Bezel Bottom 14 x S6 #12 x 1 Pan Screw 4 x S7 #12 x 2 Pan Screw 8 x #12 Screw Bezel 78 support@cedarsummitplay.com

79 Step 38: Attach Elbow Assembly to Flange Assembly Part 1 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step. A: Fit one of the Elbow Assemblies to the Flange Assembly by lining up the arrows on each assembly. (fig and 38.3) B: Attach 1 TNR2 Slide Clamp Ring to the top of the joined Assemblies using 3 (PB1) 1/4 x 3/4 Pan Bolts (with lock nut), making sure to match the arrows up with the end of the clamp ring (where a seam will be) as shown in fig and Quadrex Driver Use Quadrex Driver as a guide pin for each hole before inserting bolt. (fig. 38.3) Fig Fig Use special driver provided in locations where the curve of the elbow are difficult to reach with a standard driver. Fig Do not install bolt in Clamp Ring ends until Step 38D Flange Assembly Fig Top Slide Bolt Holes Lock Nut Lock Nut Align each elbow using the molded arrows with the seam of the clamp ring. PB1 Elbow Assembly 3 x PB1 1/4 x 3/4 Pan Bolt (1/4 lock nut) Other Parts 1 x Quadrex Driver 1 x TNR2 Slide Clamp Ring 79 support@cedarsummitplay.com

80 Step 38: Attach Elbow Assembly to Flange Assembly Part 2 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step. Fig C: Attach 1 TNR2 Slide Clamp Ring to the bottom of the joined Assemblies using 2 (PB1) 1/4 x 3/4 Pan Bolts (with lock nut) on one side and 1 (PB1) 1/4 x 3/4 Pan Bolt (with lock nut) in the other side, making sure to match the arrows up with the end of the clamp ring (where a seam will be) as shown in fig. 38.5, 38.6 and D: Connect the 2 TNR2 Slide Clamp Rings together in 2 spots using 1 (PB1) 1/4 x 3/4 Pan Bolt (with lock nut) per hole. Make sure seams and arrows line up and then tighten all bolts. (fig and 38.9). Fig Lock Nut Fig (Side not shown) PB1 Bottom Slide Bolt Holes PB1 Fig Make sure arrows are aligned Lock Nut Fig PB1 Lock Nut After the clamp rings are attached to the elbows, fasten them end to end with two pan bolts and lock nuts 5 x PB1 1/4 x 3/4 Pan Bolt (1/4 lock nut) Other Parts 1 x TNR2 Slide Clamp Ring 80 support@cedarsummitplay.com

81 Step 39: Attach Elbow Assembly to Elbow Assembly Part 1 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step. Fig A: Fit a second Elbow Assembly to the first Elbow Assembly by lining up the arrows on each assembly. Notice the elbow orientation. (fig. 39.1) B: Attach 1 TNR2 Slide Clamp Ring to the top of the joined Assemblies using 3 (PB1) 1/4 x 3/4 Pan Bolts (with lock nut), making sure to match the arrows up with the end of the clamp ring (where a seam will be) as shown in fig and Use Quadrex Driver as a guide pin for each hole before inserting bolt. Notice elbow orientation Do not install bolt in Clamp Ring ends until Step 39D Fig Top Slide Bolt Holes Elbow Assembly Fig Make sure arrows are aligned PB1 Lock Nut Elbow Assembly 3 x PB1 1/4 x 3/4 Pan Bolt (1/4 lock nut) Other Parts 1 x TNR2 Slide Clamp Ring 81 support@cedarsummitplay.com

82 Step 39: Attach Elbow Assembly to Elbow Assembly Part 2 Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step. C: Attach 1 TNR2 Slide Clamp Ring to the bottom of the joined Assemblies using 3 (PB1) 1/4 x 3/4 Pan Bolts (with lock nut), making sure to match the arrows up with the end of the clamp ring (where a seam will be) as shown in fig and D: Connect the 2 TNR2 Slide Clamp Rings together in 2 spots using 1 (PB1) 1/4 x 3/4 Pan Bolt (with lock nut) per hole. Make sure seams and arrows line up and then tighten all bolts. (fig and 39.5). Fig Bottom Slide Bolt Holes Elbow Assembly Fig Make sure arrows are aligned Lock Nut PB1 Fig PB1 Lock Nut Elbow Assembly After the clamp rings are attached to the elbows, fasten them end to end with two pan bolts and lock nuts 5 x PB1 1/4 x 3/4 Pan Bolt (1/4 lock nut) Other Parts 1 x TNR2 Slide Clamp Ring 82 support@cedarsummitplay.com

83 Step 40: Attach Elbow Assemblies and TNR2 Slide Support Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step. A: Attach the two remaining Elbow Assemblies as instructed in Steps 38 and 39. B: On the fourth Elbow Assembly attached remove the pan bolt and nut which is facing the fort (installed in Step 36). (fig. 40.1) The bolt will no longer be needed, but keep the lock nut. C: Loosely attach TNR2 Slide Support (at the slightly bent end) to the Clamp Ring using 1 (PB6) 1/4 x 1 Pan Bolt (with flat washer and the previously removed lock nut). (fig. 40.2) D: Rotate TNR2 Slide Support and attach to (2529) SL Side Panel using 1 (S6) #12 x 1 Pan Screw as shown in fig E: Fully tighten screw and bolt. Fig Fig TNR2 Slide Support Lock Nut Flat Note: Flat end down S6 PB6 Remove PB1 (1/4 x 3/4 Pan Bolt first then install PB6 (1/4 x 1 Pan Bolt with flat washer) Attach 2 remaining Elbow Assemblies 1 x S6 #12 x 1 Pan Screw 1 x PB6 1/4 x 1 Pan Bolt (1/4 flat washer & 1/4 lock nut - previously removed) Other Parts 1 x TNR2 Slide Support 4 x TNR2 Slide Clamp Ring 16 x PB1 1/4 x 3/4 Pan Bolt (1/4 lock nut) 83 support@cedarsummitplay.com

84 Step 41: Attach SL Support to Ground Back A: Insert TNR2 Post Mount on (8168) SL Support and attach with 2 (PB2) 1/4 x 1-1/4 Pan Bolts (with lock washer and t-nut). Keep these bolts loose. (fig and 41.2) B: Use (8168) SL Support as a guide to judge the proper bolt location, remove the bottom pan bolt and nut. The bolt will no longer be needed, but keep the lock nut. (fig. 41.2) C: Attach the top of the TNR2 Post Mount to TNR2 Slide Clamp Ring using 1 (PB2) 1/4 x 1-1/4 Pan Bolt (with the previously removed lock nut). (fig. 41.2) Fig TNR2 Post Mount Fig PB2 PB2 1/4 Lock 1/4 Flat 1/4 T-Nut Remove PB1 (1/4 x 3/4 Pan Bolt first then install PB2 (1/4 x 1-1/4 Pan Bolt with previously removed lock nut) 3 x PB2 1/4 x 1-1/4 Pan Bolt 2 - (1/4 lock washer & 1/4 t-nut) 1 - (1/4 lock nut - previously removed) Other Parts 1 x TNR2 Post Mount 84 support@cedarsummitplay.com

85 Step 42: Attach TNR2 Slide Exit to Exit Elbow Assembly A: Insert flange of Exit Elbow Assembly (slide elbow) into the slots on TNR2 Slide Exit. (fig. 42.1) B: Rotate Slide Exit and use Quadrex Driver as a guide pin so the holes are aligned and attach with 5 (PB1) 1/4 x 3/4 Pan Bolts (with lock nuts) starting with the bottom middle hole and working up each side. (fig and 42.3) C: At this point make sure all the slide bolts are tight. Use a 7/16 open end wrench to hold nut and then tighten bolt with Quadrex Driver on Clamp Rings. Fig Fig Exit Elbow Assembly Lock Nut Slot of TNR2 Slide Exit PB1 TNR2 Slide Exit Lock Nut PB1 Bottom of Slide Views Fig Start with this bolt PB1 5 x PB1 1/4 x 3/4 Pan Bolt (1/4 lock nut) Other Parts 1 x TNR2 Slide Exit 85 support@cedarsummitplay.com

86 Step 43: Attach Exit End Assembly to Fort Note: When installing Pan Bolts make sure to look at holes so bolts go through the side with the round recess and the lock nuts go through the side with the hexagonal recess. Keep all bolts loose until further step. Fig Top Slide Bolt Holes PB1 Elbow Assembly A: Fit the Exit End Assembly to the last Elbow Assembly by lining up the arrows on each assembly. Notice the elbow orientation. (fig. 43.1) B: Attach 1 TNR2 Slide Clamp Ring to the top of the joined Assemblies using 3 (PB1) 1/4 x 3/4 Pan Bolts (with lock nut), making sure to match the arrows up with the end of the clamp ring (where a seam will be) as shown in fig Lock Nut Exit Elbow Assembly Use Quadrex Driver as a guide pin for each hole before inserting bolt. C: Attach 1 TNR2 Slide Clamp Ring to the bottom of the joined Assemblies using 3 (PB1) 1/4 x 3/4 Pan Bolts (with lock nut), making sure to match the arrows up with the end of the clamp ring (where a seam will be) as shown in fig D: Connect the 2 TNR2 Slide Clamp Rings together in 2 spots using 1 (PB1) 1/4 x 3/4 Pan Bolt (with lock nut) per hole. Make sure seams and arrows line up and then tighten all bolts. (fig. 43.3). Make sure arrows are aligned Fig Bottom Slide Bolt Holes Fig PB1 Lock Nut After the clamp rings are attached to the elbows, fasten them end to end with two pan bolts and lock nuts PB1 Lock Nut 8 x PB1 1/4 x 3/4 Pan Bolt (1/4 lock nut) Other Parts 2 x TNR2 Slide Clamp Ring 86 support@cedarsummitplay.com

87 Step 44: Attach Slide to Fort Note: Pre-drill all holes using a 1/8 drill bit before installing the pan screws. A: Place Slide tight to the Swing Side in the opening of (2526) Cafe Panel. Notch at the bottom of slide should fit tight to the wall. (fig. 44.1, 44.2 and 44.3) B: Place (8634) Crowsnest Face B under the floor boards tight to the front and Swing Side of (2526) Cafe Panel then attach slide to fort through the floor boards and into (8634) Crowsnest Face B using 3 (S7) #12 x 2 Pan Screws. (fig. 44.1, 44.2 and 44.4) Fig S7 Floor Boards 2526 WARNING: Check entire play centre for bolts protruding beyond T-Nuts. Use extra washers to eliminate this condition. Fig Tight 8634 (hidden under floor boards) Slide Fig Swing Side Slide 2526 Notch tight to fort Slide Fig Underneath Fort View Bottom of Floor Boards Tight Wood Parts 1 x 8634 Crowsnest Face B 2 x 3 x 27-3/4 3 x S7 #12 x 2 Pan Screw Other Parts 1 x Slide 87 support@cedarsummitplay.com

88 Step 45: Glider Assembly A: Attach 1 Space Glider Handle to the Space Glider Body using 1 (G25) 5/16 x 7-1/4 Hex Bolt (with 2 flat washers and 1 lock nut). Repeat for the second Space Glider Handle. (fig. 45.1) B: Install 2 Glider Rope with Chains into each Space Glider Handle using 2-5/16 Flat s and 1 Lock Nut per rope. (fig. 45.1) Fig /16 Flat -Zinc 5/16 Lock Nut Glider Rope and Chain 5/16 Flat -Zinc 5/16 Lock Nut 5/16 x 7-1/4 Hex Bolt 5/16 Flat s 5/16 Lock Nuts Space Glider Body Space Glider Handle WARNING:Bolt must not exceed 1/2 thread past the nut 2 x G25 5/16 x 7-1/4 Hex Bolt (5/16 flat washer x 2, 5/16 lock nut) 8 x 5/16 Flat Other Parts 2 x Space Glider Handle 1 x Space Glider Body 1 x Glider Rope and Chain (pkg of 4) 4 x 5/16 Lock Nut 88 support@cedarsummitplay.com

89 Step 46: Attach Glider and Swings A: Insert flexible Swing Hanger Cover over hook. (fig. 46.1) B: Slide Swing Hanger Cover around hook until at top. (fig. 46.2) C: Hook each Swing and Glider onto hook. (fig and 46.5) D: Twist and flex Swing Hanger Cover onto open end of hook. (fig. 46.4) E: Attach Cedar Summit Plaque over 1/4 t-nut on (1248) Front Beam with 4 (S18) #6 x 1 Wood Screws. (fig and 46.6) Fig Fig Fig Fig Fig S18 x 4 Fig Cedar Summit Plaque 1248 Belt Swings Glider 4 x S18 #6 x 1 Wood Screw Other Parts 8 x Swing Hanger Cover 2 x Belt Swings 1 x Cedar Summit Plaque 89 support@cedarsummitplay.com

90 Step 47: Monkey Rail Assembly Pre-drill all pilot holes using a 1/8 drill bit before installing Wood Screws. A: Insert 3 (578) 1-1/8 x 15-7/8 Dowels into both (1565) MK Rail Shorts as shown in fig Note the pilot holes in one of the (1565) MK Rail Short are on the bottom of the board. Fig /4 3/ Note: Pilot holes at top of this rail Note: Pilot holes at bottom of this rail B: Make sure shoulder of dowel is against each rail before pre-drilling pilot holes. Drill 1/8 pilot holes through the rails and into the dowels to prevent splitting. (fig. 47.2) Fig S3 Fig C: Attach (578) 1-1/8 x 15-7/8 Dowels to both rails with 2 (S3) #8 x 2-1/2 Wood Screws per dowel. (fig. 47.3) S3 Wood Parts 3 x 578 Tennon Dowel 1-1/8 x 15-7/8 2 x 1565 MK Rail Short 2 x 4 x 50 6 x S3 #8 x 2-1/2 Wood Screw 90 support@cedarsummitplay.com

91 Step 48: Monkey Ladder Assembly A: Insert 2 (858) 1-1/8 x 18-5/8 Dowels into 2 (2735) MK Post as shown in fig Fig Fig B: Make sure shoulder of dowels are against each post before pre-drilling pilot holes. Drill 1/8 pilot holes through the posts and into the dowels to prevent splitting. (fig. 48.2) 858 C: Attach each (858) 1-1/8 x 18-5/8 Dowels to both posts with 2 (S3) #8 x 2-1/2 Wood Screws per dowel. One screw is installed from top of the rails and the other from the bottom as shown in fig D: At bottom of (2735) MK Post attach (2728) MK Ground with 2 (H4) 1/4 x 4 Hex Bolts (with lock washer, flat washer and t-nut). Be sure to keep the bolts loose. (fig. 48.3) Note: Pre-drill all holes using a 1/8 drill bit before installing the lag screws. E: Make sure the assembly is square and then attach (2734) Long Diagonal to the end shown below on (2728) MK Ground and (2731) Short Diagonal to the other side with 1 (H2) 1/4 x 2 Hex Bolt (with lock washer, flat washer and t-nut) per diagonal, keeping the bolts loose. Attach both diagonals to (2735) MK Posts with 1 (WL5) 1/4 x 2-1/2 Wafer Lag (with flat washer) per diagonal. Once lag screws are installed tighten all bolts from Steps D & E. (fig. 48.3) H H WL5 Fig H2 1/4 Flat 1/4 Lock S3 x 2 per dowel 1/4 T-Nut 2734 WL5 5/16 Flat 2735 Wood Parts 2 x 2735 MK Post 2 x 4 x 80-7/8 1 x 2728 MK Ground 1 x 4 x 49-15/64 1 x 2734 Long Diagonal 2 x3 x 42 1 x 2731 Short Diagonal 2 x 3 x 18 2 x 858 Tennon Dowel 1-1/8 x 18-5/8 2 x H4 1/4 x 4 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 2 x H2 1/4 x 2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 2 x WL5 1/4 x 2-1/2 Wafer Lag (5/16 flat washer) 4 x S3 #8 x 2-1/2 Wood Screw 91 support@cedarsummitplay.com

92 Step 49: Connect Monkey Bar Assemblies Note: Pre-drill all holes using a 1/8 drill bit before installing the pan screws. A: Using a Monkey Bracket connect (1565) MK Rail Shorts to each (2735) MK Post with 1 (G10) 5/16 x 3 Hex Bolt (with lock washer, flat washer and t-nut) per bracket and Monkey Bracket to the rails using 2 (S6) #12 x 1 Pan Screws per rail as shown in fig and B: Attach Monkey Bracket to both (2735) MK Posts with 2 (S6) #12 x 1 Pan Screws per bracket. (fig. 49.2) 3/4 (Hole to edge) Fig /16 Flat 1565 Fig /16 T-Nut 1-1/ Monkey Bracket /16 Lock G10 S6 x o 2 x G10 5/16 x 3 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 8 x S6 #12 x 1 Pan Screws Other Parts 2 x Monkey Bracket 92 support@cedarsummitplay.com

93 Step 50: Attach MB Hanger Brackets A: Place 1 MB Hanger Bracket at the ends of each (1565) MK Rail Short so they wrap around the bottoms of the rails then attach with 1 (PB5) 1/4 x 2 Pan Bolt (with flat washer x 2 and lock nut). (fig and 50.2) Fig Fig /4 Flat 1/4 Lock Nut Flush PB5 MB Hanger Bracket 1/4 Flat 2 x PB5 1/4 x 2 Pan Bolt (1/4 flat washer x 2 and lock nut) Other Parts 2 x MB Hanger Bracket 93 support@cedarsummitplay.com

94 Step 51: Connect Monkey Bar Assembly to Fort Part 1 A: On the Back of the fort, tight to the bottom of (2494) Middle Back and flush to the outside edges of (2482) Back Wall Support and (2500) Crowsnest Post attach (2732) MK Lower Back to (2482) Back Wall Support, (2473) Post and (2500) Crowsnest Post with 4 (S7) #12 x 2 Pan Screws. Notice bolt holes are over the opening (fig and 51.2) Fig Back S7 Fig Flush Wood Parts 1 x 2732 MK Lower Back 5/4 x 5 x 34-1/8 4 x S7 #12 x 2 Pan Screw 94 support@cedarsummitplay.com

95 Step 51: Connect Monkey Bar Assembly to Fort Part 2 B: Place the Monkey Bar Assembly against (2732) MK Lower Back in the opening between (2482) Back Wall Support and (2473) Post then attach the MB Hanger Brackets to (2732) MK Lower Back with 1 (PB2) 1/4 x 1-1/4 Pan Bolt (with lock washer, flat washer and t-nut) per bracket in the inside holes and (S7) #12 x 2 Pan Screw per bracket in the outside holes. (fig and 51.4) Fig Fig PB2 1/4 Lock 1/4 Flat 1/4 T-Nut (hidden) MB Hanger Bracket 2732 x 1 per bracket 1565 MB Hanger Bracket S7 x 1 per bracket x PB2 1/4 x 1-1/4 Pan Bolt (1/4 lock washer, 1/4 flat washer, and t-nut) 2 x S7 #12 x 2 Pan Screw 95 support@cedarsummitplay.com

96 Step 52: Attach Monkey Ladder Ground Stake A: Drive 1 (0318) Ground Stake 10-1/2 into the ground at (1565) MK Rail Short next to (2731) Short Diagaonal then attach using 2 (S3) #8 x 2-1/2 Wood Screws. (fig and 52.2) WARNING: To prevent tipping and avoid potential injury, stakes must be driven 10-1/2 into ground. Digging or driving stakes can be dangerous if you do not check first for underground wiring, cables or gas lines. Fig Fig S3 10-1/2 In Ground 0318 Wood Parts 1 x 0318 Ground Stake 1-1/4 x 1-1/2 x 14 2 x S3 #8 x 2-1/2 Wood Screw 96 support@cedarsummitplay.com

97 Final Step: Attach I.D. Plaque ATTACH THIS WARNING & I.D. PLAQUE TO A PROMINENT LOCATION ON YOUR PLAY EQUIPMENT! (Fort or Swing Post) This provides warnings concerning safety and important contact information. A Tracking Number is provided to allow you to get critical information or order replacement parts for this specific model. S5 FORT OR SWING POST I.D. Plaque - Cedar Summit WARNING A: Attach Attach I.D. Plaque with screws - Cedar provided Summit to to a location a location on your set that is easily seen and read on your by a supervising set that is adult easily using seen 4 (S5) and #8 x 1/2 Pan Screws. read by a supervising adult. I.D. Plaque - Cedar Summit 97 support@cedarsummitplay.com