v3.1 HMC59MSGE AMPLIFIER,. -.9 GHz Typical Applications The HMC59MSGE is ideal for: DTV Receivers Multi-Tuner Set Top Boxes PVRs & Home Gateways Functional Diagram Features Single-ended or Balanced Output High Output IP3: +7 dbm Low Noise Figure: 3.5 db Single Positive Supply: +5V 75 Ohm Input General Description The HMC59MSGE is a GaAs phemt MMIC Low Noise Amplifier that are ideal pre-amplifiers for CATV Set Top Box, Home Gateway, and Digital Television receiver operating between and 9 MHz. This high dynamic range LNA has been optimized to provide 3.5 db noise figure and +7 dbm output IP3 from a single supply of +5V @ 1 ma. The outputs of this LNA are extremely well balanced, and can be used to drive a differential input tuner with very high input IP requirements. This dual purpose LNA can also be used as an active splitter driving two single-ended input tuners. This LNA is housed in a RoHS compliant MSOPG SMT package with exposed ground paddle. Electrical Specifications, 75 Ohm System, T A = +5 C, Vdd = +5V Parameter* Min. Typ. Max. Units Frequency Range. -.9 GHz Gain 5 db Gain Variation over Temperature.1. db/ C Noise Figure 3.5 5. db Input Return Loss db Output Return Loss 15 db Output Power for 1 db Compression (P1dB) 1.5 dbm Output Third Order Intercept (OIP3) 7 dbm Output Second Order Intercept (OIP) 5 dbm Amplitude Balance.3 db Phase Balance deg Supply Current (Idd) 1 ma * Unless otherwise noted, all measurements performed with balun on the output. 1 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, P.O. Box 91, Norwood, MA -91 Phone: 71-39-7 Order online at www.analog.com Application Support: Phone: 1--ANALOG-D
HMC59MSGE v3.1 AMPLIFIER,. -.9 GHz Broadband Gain & Return Loss Gain vs. Temperature RESPONSE (db) - - -1-1 - S1 S11 S.1..3..5..7..9 1 1.1 1. 1.3 Input Return Loss vs. Temperature RETURN LOSS (db) - - - - +5 C - C GAIN (db) Output Return Loss vs. Temperature RETURN LOSS (db) -5-1 -15 +5C +5C - C.1..3..5..7..9 1 +5 C - C -1.1..3..5..7..9 1 -.1..3..5..7..9 1 Reverse Isolation vs. Temperature Noise Figure vs. Temperature 1 REVERSE ISOLATION (db) -5-1 -15 - -5-3 +5 C - C NOISE FIGURE (db) +5 C - C -35.1..3..5..7..9 1.1..3..5..7..9 1 All measurements taken in 75 Ohm system. For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, P.O. Box 91, Norwood, MA -91 Phone: 71-39-7 Order online at www.analog.com Application Support: Phone: 1--ANALOG-D
HMC59MSGE v3.1 AMPLIFIER,. -.9 GHz P1dB vs. Temperature Psat vs. Temperature 15 17 P1dB (dbm) 1 13 1 11 1 9 +5 C - C.1..3..5..7..9 1 Output IP3 vs. Temperature IP3 (dbm) 3 3 +5 C - C Psat (dbm) Gain, Noise Figure & P1dB vs. Supply Voltage @ 5 MHz GAIN & NOISE FIGURE (db) 1 15 1 13 1 11 1 9 1 P1dB +5 C - C.1..3..5..7..9 1 GAIN NOISE FIGURE 15 13 11 9 7 P1dB (dbm).1..3..5..7..9 1 5 3 3.5.5 5 5.5 SUPPLY VOLTAGE (Vdc) Amplitude Balance * Phase Balance * 1 AMPLITUDE ERROR (db) -.1 -. -.3 -. PHASE ERROR (deg) - - -.5.1..3..5..7..9 1 -.1..3..5..7..9 1 * Data taken without balun on the output. All measurements taken in 75 Ohm system. 3 For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, P.O. Box 91, Norwood, MA -91 Phone: 71-39-7 Order online at www.analog.com Application Support: Phone: 1--ANALOG-D
HMC59MSGE v3.1 AMPLIFIER,. -.9 GHz Absolute Maximum Ratings Typical Supply Current vs. Vdd Drain Bias Voltage (Vdd) +7V RF Input Power (RFIN) 1 dbm Channel Temperature 15 C Continuous Pdiss (T = 5 C) (derate mw/ C above 5 C) Thermal Resistance (channel to ground paddle) 1.3 W 9 C/W Storage Temperature -5 to +15 C Operating Temperature - to +5 C ESD Sensitivity (HBM) Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing PKG-55 3.1 3..9.5 BSC.9..7 1 3.1 3..9 5 5.5.9.75 TOP VIEW 1.95 BSC SIDE VIEW 1.1 MAX.5 GAGE PLANE EXPOSED PAD BOTTOM VIEW.1 1.9 1.7 1.5 1.3 1.1 Vdd (V) END VIEW.13. MAX.7.33.95 COPLANARITY.55 REF.5.1. COMPLIANT TO JEDEC STANDARDS MO-17-AA-T Idd (ma) 3. 117.1 3.3 117.5 3. 117.9.5 11.5 5. 119. 5.5 119.3 FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET..3. 9-19-1-A -Lead Small Outline Package with Exposed Pad [MINI_SO_EP] (RH--3) Dimensions shown in millimeters Package Information Part Number Package Body Material Lead Finish MSL Rating Package Marking [] [1] H59 HMC59MSGE RoHS-compliant Low Stress Injection Molded Plastic 1% matte Sn MSL1 XXXX [1] Max peak reflow temperature of C [] -Digit lot number XXXX For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, P.O. Box 91, Norwood, MA -91 Phone: 71-39-7 Order online at www.analog.com Application Support: Phone: 1--ANALOG-D
HMC59MSGE v3.1 AMPLIFIER,. -.9 GHz Pin Descriptions Pin Number Function Description Interface Schematic 1, Vdd1, Vdd Power supply voltage for the first stage. An external choke inductor is required. See application circuit. FEED Feedback capacitor for the first stage. 3 RFIN ACG1 This pin is DC coupled and requires a DC blocking cap. See application circuit. This pin has to be terminated by an external capacitor. See application circuit. 5 RFOUT RF differential output. This port is DC coupled. RFOUT RF differential output 1. This port is DC coupled. 7 ACG This pin has to be terminated by an external capacitor. See application circuit. Vdd Power supply voltage for second stage. An external choke inductor is required. See application circuit. 5 For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, P.O. Box 91, Norwood, MA -91 Phone: 71-39-7 Order online at www.analog.com Application Support: Phone: 1--ANALOG-D
HMC59MSGE v3.1 AMPLIFIER,. -.9 GHz Application Circuit for 193 - HMC59MSGE (-port) Application Circuit for 1131 - HMC59MSGE (3-port) For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, P.O. Box 91, Norwood, MA -91 Phone: 71-39-7 Order online at www.analog.com Application Support: Phone: 1--ANALOG-D
HMC59MSGE v3.1 AMPLIFIER,. -.9 GHz Evaluation PCB List of Materials for Evaluation PCB 193 [1] Item Description J1, J BOMAR F Type 75 Ohm Connectors J3, J DC Pin C1, C 1 kpf Capacitor, Pkg. C3 C C5 C 15 pf Capacitor, Pkg. 39 pf Capacitor, 3 Pkg..7 µf Capacitor, Tantalum 1, pf Capacitor, Pkg. C7, C 1 pf Capacitor, Pkg. L1, L 5 nh Inductor, 3 Pkg.. R1, R Ohm Resistor, 3 Pkg. U1 U PCB [] HMC59MSGE Low Noise Amplifier ETC1-1-13 l:l Balun 193 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [] Circuit Board Material: FR The circuit board used in the application should use RF circuit design techniques. Signal lines should have 75 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Analog Devices, upon request. 7 For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, P.O. Box 91, Norwood, MA -91 Phone: 71-39-7 Order online at www.analog.com Application Support: Phone: 1--ANALOG-D
HMC59MSGE v3.1 AMPLIFIER,. -.9 GHz Evaluation PCB List of Materials for Evaluation PCB 1131 [1] Item J1 - J3 Description J, J5 DC Pin BOMAR F Type 75 Ohm Connectors C1, C 1 kpf Capacitor, Pkg. C3 C C5 C 15 pf Capacitor, Pkg. 1, pf Capacitor, Pkg. 39 pf Capacitor, 3 Pkg..7 µf Capacitor, Tantalum C7, C 1 pf Capacitor, Pkg. L1, L 5 nh Inductor, 3 Pkg.. U1 PCB [] HMC59MSGE Low Noise Amplifier 1131 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [] Circuit Board Material: FR The circuit board used in the application should use RF circuit design techniques. Signal lines should have 75 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Analog Devices, upon request. For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, P.O. Box 91, Norwood, MA -91 Phone: 71-39-7 Order online at www.analog.com Application Support: Phone: 1--ANALOG-D