CERTIFICATE Issued Date: May 21, 2008 Report No.: 085206R-ITUSP02V01 This is to certify that the following designated product Product : IPC Trade name : VISION BOX Model Number : VB-115C/VB-115H/VB-115C-XXX/VB-115H-XXX Company Name : ICPDAS CO., LTD This product, which has been issued the test report listed as above in QuieTek Laboratory, is based on a single evaluation of one sample and confirmed to comply with the requirements of the following EMC standard. FCC CFR Title 47 Part 15 Subpart B: 2007, CISPR 22: 2005 ANSI C63.4: 2003 TEST LABORATORY Vincent Lin / Deputy Manager No.5-22, Ruei-Shu Valley, Ruei-Ping Tsuen Lin Kou Shiang, Taipei 244 Taiwan, R.O.C. TEL:+886-2-8601-3788 FAX:+886-2-8601-3789 Email:service@quietek.com http://www.quietek.com
Test Report Product Name : IPC Model No. : VB-115C/VB-115H/VB-115C-XXX/VB-115H-XXX Applicant : ICPDAS CO., LTD Address : No.111, Guangfu N. Rd., Hukou Township, Hsinchu County, Taiwan 30351, R.O.C. Date of Receipt : 2006/10/11 Issued Date : 2008/05/21 Report No. : 085206R-ITUSP02V01 Version : V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF, NVLAP, NIST or any agency of the Government. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation.
DECLARATION OF CONFORMITY Per FCC Part 2 Section 2. 1077(a) The following equipment: Product Name :IPC Model Number :VB-115C/VB-115H/VB-115C-XXX/VB-115H-XXX Company Name :ICPDAS CO., LTD It s herewith confirmed to comply with the requirements of FCC Part 15 Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The result of electromagnetic emission has been evaluated by QuieTek EMC laboratory (NVLAP Lab. Code : 200533-0 ) and showed in the test report. ( Report No. : 085206R-ITUSP02V01) It is understood that each unit marketed is identical to the device as tested, and any changes to the device that could adversely affect the emission characteristics will require retest. The following importer / manufacturer is responsible for this declaration: Company Name Company Address Telephone Facsimile : Person is responsible for marking this declaration: Name ( Full name ) Position / Title Date Legal Signature
Test Report Certification Issued Date : 2008/05/21 Report No. : 085206R-ITUSP02V01 Product Name : IPC Applicant : ICPDAS CO., LTD Address : No.111, Guangfu N. Rd., Hukou Township, Hsinchu County, Taiwan 30351, R.O.C. Manufacturer : NEXCOM International Co., LTD Model No. : VB-115C/VB-115H/VB-115C-XXX/VB-115H-XXX Rated Voltage : AC 120 V / 60 Hz EUT Voltage : AC 100-240V, 50-60Hz Trade Name : VISION BOX Applicable Standard : FCC CFR Title 47 Part 15 Subpart B: 2007 Class A CISPR 22: 2005, ANSI C63.4: 2003 ICES-003 Issue 4: 2004 Class A Test Result : Complied Performed Location : Quietek Corporation (Linkou Laboratory) No.5-22, Ruei-Shu Valley, Ruei-Ping Tsuen Lin Kuo Shiang, Taipei, 244 Taiwan, R.O.C. TEL:+866-2-8601-3788 / FAX:+886-2-8601-3789 Documented By : Reviewed By : Approved By : ( Senior Engineering Adm. Specialist / Anita Chou ) (Engineer / Lance Chi) ( Deputy Manager / Vincent Lin) Page: 2 of 35
Laboratory Information We, QuieTek Corporation, are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited/accepted (audited or listed) by the following related bodies in compliance with ISO 17025, EN 45001 and specified testing scopes: Taiwan R.O.C. : BSMI, NCC, TAF Germany : TUV Rheinland Norway : Nemko, DNV USA : FCC, NVLAP Japan : VCCI The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation s Web Site :http://tw.quietek.com/modules/enterprise/services.php?item=100 The address and introduction of QuieTek Corporation s laboratories can be founded in our Web site : http://www.quietek.com/ If you have any comments, Please don t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory : No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL:+886-3-592-8858 / FAX:+886-3-592-8859 E-Mail : service@quietek.com LinKou Testing Laboratory : No. 5, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwan, R.O.C. TEL : 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : service@quietek.com Suzhou (China) Testing Laboratory : No. 99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., Suzhou,China. TEL : +86-512-6251-5088 / FAX : +86-512-6251-5098 E-Mail : service@quietek.com Page: 3 of 35
TABLE OF CONTENTS Description Page 1. General Information... 5 1.1. EUT Description... 5 1.2. Mode of Operation... 5 1.3. Tested System Details... 6 1.4. Configuration of Tested System... 7 1.5. EUT Exercise Software... 8 2. Technical Test... 9 2.1. Summary of Test Result... 9 2.2. List of Test Equipment... 10 2.3. Measurement Uncertainty... 11 2.4. Test Environment... 12 3. Conducted Emission... 13 3.1. Test Specification... 13 3.2. Test Setup... 13 3.3. Limit... 13 3.4. Test Procedure... 14 3.5. Test Result... 15 3.6. Test Photograph... 21 4. Radiated Emission... 22 4.1. Test Specification... 22 4.2. Test Setup... 22 4.3. Limit... 23 4.4. Test Procedure... 24 4.5. Test Result... 25 4.6. Test Photograph... 29 5. Attachment... 31 EUT Photograph... 31 Page: 4 of 35
1. General Information 1.1. EUT Description Product Name Trade Name Model No. IPC VISION BOX VB-115C/VB-115H/VB-115C-XXX/VB-115H-XXX Component CPU Intel, Pentium M 725 1.6GHz/100MHz, FSB: 400MHz Mother Board Intel, I855-ITE8712 HDD Toshiba, HDD2197 VGA Card On Board LAN Card On Board Sound Card On Board DDR-RAM A Pacer, 512MB UNB PC2700 CL2.5*1 S-Video Cable Shielded, 0.15m Signal Cable Shielded, 3.0m PS/2 Cable Shielded, 0.15m Printer to RS-232 Cable Shielded, 0.25m Power Adapter FSP, FSP120-AAB Input: AC 100-240V, 50-60Hz Output: DC 19V-6.32A Cable in: Non-Shielded, 1.8m with one ferrite core bonded. Power cord: Non-Shielded, 1.8m 1.2. Mode of Operation QuieTek has verified the construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: Pre-Test Mode Mode 1:Intel Pentium M 725 1.6GHz/100MHz,Full system Final Test Mode Emission Mode 1:Intel Pentium M 725 1.6GHz/100MHz,Full system Page: 5 of 35
1.3. Tested System Details The types for all equipments, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. Power Cord 1 Modem ACEEX DM-1414 0102027533 Non-Shielded, 1.8m 2 Modem ACEEX DM-1414 0102027537 Non-Shielded, 1.8m 3 Modem ACEEX DM-1414 0102027558 Non-Shielded, 1.8m 4 Modem ACEEX DM-1414 0102027532 Non-Shielded, 1.8m 5 Monitor SONY PVM-14M2U 2111366 Non-Shielded, 1.8m 6 Microphone & PCHOME N/A N/A Non-Shielded, 2m Earphone 7 Keyboard HP SK-2506 C0008335817 N/A 8 Mouse HITACHI PC-KM1300 N/A N/A 9 USB 2.0 HDD AACOM F12-UF N/A Power by PC 10 USB 2.0 HDD AACOM F12-UF N/A Power by PC 11 USB 2.0 HDD AACOM F12-UF N/A Power by PC 12 USB 2.0 HDD AACOM F12-UF N/A Power by PC 13 USB 2.0 HDD AACOM F12-UF N/A Power by PC 14 USB 2.0 HDD AACOM F12-UF N/A Power by PC 15 Monitor ADI CM703 038054T10203876A Non-Shielded, 1.8m 16 Notebook PC ASUS S1300 24NP035390 Non-shielded, 1.8m 17 Notebook PC ASUS S1300 26NP018680 Non-Shielded, 1.8m Page: 6 of 35
1.4. Configuration of Tested System Connection Diagram Signal Cable Type Signal cable Description A RS232 Cable Shielded, 1.5m B D-SUB Cable Shielded, 1.8m, with two ferrite cores bonded C RS232 Cable Shielded, 1.5m D RS232 Cable Shielded, 1.5m E RS232 Cable Shielded, 1.5m F Earphone & Microphone Cable Non-Shielded, 1.6m G Keyboard Cable Shielded, 1.8m H Mouse Cable Shielded, 1.8m I Signal Cable Shielded, 3.0m J S-VIDEO Cable Shielded, 1.6m K USB Cable Shielded, 1.5m L USB Cable Shielded, 1.5m M USB Cable Shielded, 1.5m N USB Cable Shielded, 1.5m O USB Cable Shielded, 1.5m P USB Cable Shielded, 1.0m Q LAN Cable Non-Shielded, 3.0m R LAN Cable Non-Shielded, 3.0m Page: 7 of 35
1.5. EUT Exercise Software 1 Setup the EUT and simulators as shown on 1.4. 2 Turn on the power of all equipment. 3 The EUT will start to operate and display the video figure from the signal source. 4 The EUT will display video figure on monitor. 5 Repeat the above procedure (3) to (4). Page: 8 of 35
2. Technical Test 2.1. Summary of Test Result No deviations from the test standards Deviations from the test standards as below description: Emission Performed Item Normative References Conducted Emission FCC CFR Title 47 Part 15 Subpart B: 2007 Class A ANSI C63.4: 2003 Radiated Emission FCC CFR Title 47 Part 15 Subpart B: 2007 Class A ANSI C63.4: 2003 Test Performed Yes Yes Deviation No No Page: 9 of 35
2.2. List of Test Equipment Conducted Emission / SR1 Instrument Manufacturer Type No. Serial No Cal. Date EMI Test Receiver R&S ESCS 30 836858/022 2006/02/18 LISN R&S ENV4200 833209/007 2006/07/13 LISN R&S ESH3-Z5 836679/020 2006/02/14 Pulse Limiter R&S ESH3-Z2 357.88.10.52 2006/09/04 Radiated Emission / Site3 Instrument Manufacturer Type No. Serial No Cal. Date Bilog Antenna Schaffner Chase CBL6112B 2704 2006/08/09 Broadband Horn Antenna Schwarzbeck BBHA9170 208 2006/07/25 EMI Test Receiver R&S ESI 26 838786/004 2006/06/19 EMI Test Receiver R&S ESCS 30 838251/001 2006/05/11 Horn Antenna Schwarzbeck BBHA9120D 305 2006/08/10 Pre-Amplifier MITEQ AMF-4D-18040 0-45-6P 925974 2006/01/03 Pre-Amplifier QTK N/A N/A 2006/01/03 Spectrum Analyzer Advantest R3162 101102468 2006/10/24 Page: 10 of 35
2.3. Measurement Uncertainty Conducted Emission The measurement uncertainty is evaluated as ± 2.26 db. Radiated Emission The measurement uncertainty is evaluated as ± 3.19 db. Page: 11 of 35
2.4. Test Environment Performed Item Items Required Actual Temperature ( C) 15-35 25 Conducted Emission Humidity (%RH) 25-75 50 Barometric pressure (mbar) 860-1060 950-1000 Temperature ( C) 15-35 25 Radiated Emission Humidity (%RH) 25-75 50 Barometric pressure (mbar) 860-1060 950-1000 Page: 12 of 35
3. Conducted Emission 3.1. Test Specification According to Standard : FCC Part 15 Subpart B, ANSI C63.4 3.2. Test Setup 3.3. Limit Limits Frequency (MHz) QP (dbuv) AV (dbuv) 0.15-0.50 79 66 0.50-5.0 73 60 5.0-30 73 60 Remarks: In the above table, the tighter limit applies at the band edges. Page: 13 of 35
3.4. Test Procedure The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50 ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please refers to the block diagram of the test setup and photographs.) Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed on conducted measurement. Conducted emissions were invested over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9kHz. Page: 14 of 35
3.5. Test Result Site : SR-1 Time : 2006/10/20-03:26 Limit : CISPR_A_00M_QP Margin : 10 EUT : IPC Probe : LISN-020(L) - Line1 Power : AC 120V/60Hz Note : Mode 1 Page: 15 of 35
Site : SR-1 Time : 2006/10/20-03:27 Limit : CISPR_A_00M_QP Margin : 0 EUT : IPC Probe : LISN-020(L) - Line1 Power : AC 120V/60Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv) (db) (dbuv) 1 * 0.189 0.202 51.120 51.322-27.678 79.000 QUASIPEAK 2 0.236 0.203 49.450 49.653-29.347 79.000 QUASIPEAK 3 0.498 0.216 44.280 44.496-34.504 79.000 QUASIPEAK 4 0.666 0.227 37.100 37.327-35.673 73.000 QUASIPEAK 5 2.291 0.290 37.790 38.080-34.920 73.000 QUASIPEAK 6 4.298 0.367 41.290 41.657-31.343 73.000 QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 16 of 35
Site : SR-1 Time : 2006/10/20-03:27 Limit : CISPR_A_00M_AV Margin : 0 EUT : IPC Probe : LISN-020(L) - Line1 Power : AC 120V/60Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv) (db) (dbuv) 1 0.189 0.202 33.210 33.412-32.588 66.000 AVERAGE 2 0.236 0.203 29.800 30.003-35.997 66.000 AVERAGE 3 0.498 0.216 26.500 26.716-39.284 66.000 AVERAGE 4 * 0.666 0.227 33.630 33.857-26.143 60.000 AVERAGE 5 2.291 0.290 29.680 29.970-30.030 60.000 AVERAGE 6 4.298 0.367 32.910 33.277-26.723 60.000 AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 17 of 35
Site : SR-1 Time : 2006/10/20-03:28 Limit : CISPR_A_00M_QP Margin : 10 EUT : IPC Probe : LISN-020(N) - Line2 Power : AC 120V/60Hz Note : Mode 1 Page: 18 of 35
Site : SR-1 Time : 2006/10/20-03:30 Limit : CISPR_A_00M_QP Margin : 0 EUT : IPC Probe : LISN-020(N) - Line2 Power : AC 120V/60Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv) (db) (dbuv) 1 * 0.173 0.202 51.440 51.642-27.358 79.000 QUASIPEAK 2 0.220 0.202 48.790 48.992-30.008 79.000 QUASIPEAK 3 0.486 0.216 39.260 39.476-39.524 79.000 QUASIPEAK 4 0.892 0.232 32.270 32.502-40.498 73.000 QUASIPEAK 5 2.712 0.306 40.400 40.706-32.294 73.000 QUASIPEAK 6 3.951 0.352 43.010 43.362-29.638 73.000 QUASIPEAK Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 19 of 35
Site : SR-1 Time : 2006/10/20-03:30 Limit : CISPR_A_00M_AV Margin : 0 EUT : IPC Probe : LISN-020(N) - Line2 Power : AC 120V/60Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv) (db) (dbuv) 1 0.173 0.202 37.290 37.492-28.508 66.000 AVERAGE 2 0.220 0.202 30.520 30.722-35.278 66.000 AVERAGE 3 0.486 0.216 19.370 19.586-46.414 66.000 AVERAGE 4 0.892 0.232 21.980 22.212-37.788 60.000 AVERAGE 5 2.712 0.306 27.780 28.086-31.914 60.000 AVERAGE 6 * 3.951 0.352 33.730 34.082-25.918 60.000 AVERAGE Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 20 of 35
3.6. Test Photograph Test Mode : Mode 1:Intel Pentium M 725 1.6GHz/100MHz,Full system Description : Front View of Conducted Test Test Mode : Mode 1:Intel Pentium M 725 1.6GHz/100MHz,Full system Description : Back View of Conducted Test Page: 21 of 35
4. Radiated Emission 4.1. Test Specification According to EMC Standard : FCC Part 15 Subpart B, ANSI C63.4 4.2. Test Setup Under 1GHz Test Setup: Above 1GHz Test Setup: Page: 22 of 35
4.3. Limit Under 1GHz test shall not exceed the following value: Frequency (MHz) Limits Distance (m) dbuv/m 30 230 10 40 230 1000 10 47 Remark: 1. The tighter limit shall apply at the edge between two frequency bands. 2. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. Above 1GHz test shall not exceed the following value: FCC Part 15 Subpart B Paragraph 15.109 Limits (dbuv/m) Frequency (MHz) Distance(m) dbuv/m 30-88 10 39 88-216 10 43.5 216-960 10 46.4 Above 960 10 49.5 Remark: 1. The tighter limit shall apply at the edge between two frequency bands. 2. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. 3. RF Voltage (dbuv/m) = 20 log RF Voltage (uv/m) Page: 23 of 35
4.4. Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level and the antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated on radiated measurement. For an unintentional radiator, including a digital device, the spectrum shall be investigated from the lowest radio frequency signal generated or used in the device, without going below the lowest frequency for which a radiated emission limit is specified, up to the frequency shown in the folowing table: Highest frequency generated or used in the device or on which the device operates or tunes (MHz) Upper frequency of measurement range (MHz) Below 1.705 30 1.705 108 1000 108 500 2000 500 1000 5000 5 th harmonic of the highest Above 1000 frequency or 40 GHz, whichever is lower On any frequency or frequencies below or equal to 1000 MHz, the radiated limits shown are based on measuring equipment employing a quasi-peak detector function and above 1000 MHz, the radiated limits shown are based measuring equipment employing an average detector function. When average radiated emission measurement are included emission measurement Above 1000 MHz, there also is a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 db above the maximum permitted average limit. For class A, the measurement distance between the EUT and antenna is 10 meters for under 1GHz and above 1GHz. For class B, the measurement distance between the EUT and antenna is 10 meters for under 1GHz and 3 meters for above 1GHz. The bandwidth below 1GHz setting on the field strength meter (R&S Test Receiver ESCS 30) is 120 khz and above 1GHz is 1MHz. Page: 24 of 35
4.5. Test Result Site : OATS-3 Time : 2006/10/12-16:20 Limit : CISPR_A_10M_QP Margin : 6 EUT : IPC Probe : CBL6112B(2704) - HORIZONTAL Power : AC 120V/60Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv/m) (db) (dbuv/m) 1 133.310 13.971 14.350 28.321-11.679 40.000 QUASIPEAK 2 299.960 17.005 19.360 36.366-10.634 47.000 QUASIPEAK 3 399.950 20.899 18.850 39.749-7.251 47.000 QUASIPEAK 4 * 533.260 23.840 22.013 45.854-1.146 47.000 QUASIPEAK 5 666.580 25.916 9.790 35.705-11.295 47.000 QUASIPEAK 6 889.080 28.481 11.940 40.421-6.579 47.000 QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 25 of 35
Site : OATS-3 Time : 2006/10/12-15:56 Limit : CISPR_A_10M_QP Margin : 6 EUT : IPC Probe : CBL6112B(2704) - VERTICAL Power : AC 120V/60Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv/m) (db) (dbuv/m) 1 48.000 10.021 17.140 27.162-12.838 40.000 QUASIPEAK 2 133.310 13.971 17.280 31.251-8.749 40.000 QUASIPEAK 3 299.960 17.005 14.660 31.666-15.334 47.000 QUASIPEAK 4 366.620 19.596 18.840 38.437-8.563 47.000 QUASIPEAK 5 * 533.260 23.840 16.840 40.681-6.319 47.000 QUASIPEAK 6 889.080 28.481 11.010 39.491-7.509 47.000 QUASIPEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 26 of 35
Site : OATS 3 Time : 2006/10/26-05:43 Limit : FCC_A_(Above_1G)_3M_PK Margin : 6 EUT : IPC Probe : HORN9120D+9170D(1~40G) - HORIZONTAL Power : AC 120V/60Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv/m) (db) (dbuv/m) 1 * 1067.500-5.621 49.595 43.974-35.526 79.500 PEAK 2 1332.500-4.738 39.123 34.385-45.115 79.500 PEAK 3 3850.000 1.099 39.662 40.760-38.740 79.500 PEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 27 of 35
Site : OATS 3 Time : 2006/10/26-05:46 Limit : FCC_A_(Above_1G)_3M_PK Margin : 6 EUT : IPC Probe : HORN9120D+9170D(1~40G) - VERTICAL Power : AC 120V/60Hz Note : Mode 1 Frequency Correct Factor Reading Level Measure Level Margin Limit Detector Type (MHz) (db) (dbuv) (dbuv/m) (db) (dbuv/m) 1 * 1067.500-5.621 55.430 49.809-29.691 79.500 PEAK 2 1120.000-5.483 50.916 45.432-34.068 79.500 PEAK 3 1332.500-4.738 46.262 41.524-37.976 79.500 PEAK 4 2665.000-1.587 39.595 38.008-41.492 79.500 PEAK Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 28 of 35
4.6. Test Photograph Test Mode : Mode 1:Intel Pentium M 725 1.6GHz/100MHz,Full system Description : Front View of Radiated Test Test Mode : Mode 1:Intel Pentium M 725 1.6GHz/100MHz,Full system Description : Back View of Radiated Test Page: 29 of 35
Test Mode : Mode 1:Intel Pentium M 725 1.6GHz/100MHz,Full system Description : Front View of High Frequency Radiated Test Page: 30 of 35
5. Attachment EUT Photograph (1) EUT Photo (2) EUT Photo Page: 31 of 35
(3) EUT Photo (4) EUT Photo Page: 32 of 35
(5) EUT Photo (6) EUT Photo Page: 33 of 35
(7) EUT Photo (8) EUT Photo Page: 34 of 35
(9) EUT Photo Page: 35 of 35