CCITT G.703 Baluns REGULAR TYPE The standard single baluns come with a variety of coaxial interfaces and a RJ45 twisted pair connection. MB8S Shielded RJ45 Jack to Male BNC STANDARD TYPE M5D8S Shielded RJ45 Jack to Male 1.6/5.6 DIN KEYSTONE TYPE This baluns are designed to easily snap in and out of the wall plate, patch panel and surface box modular configurations. FBK8 Unshielded RJ45 Keystone Jack to Female BNC DUAL TYPE The dual balun provide transformation of 75Ω coaxial TX/RX Pair to two 120Ω twisted pair output on a single RJ45 jack. - No AC power or batteries needed. - Link-to-data isolation: Mini. 250v. - Bi-directional signal conversion. - Operating temperature: 0 C~75 C. - Ultra-miniature enclosure. - Transmission distance: 180m via Cat.5e cable. 2FB8S Shielded RJ45 Jack to 2 x Female BNC 2F5D8S Shielded RJ45 Jack to 2 x Female 1.6/5.6 DIN DUAL FLY-LEAD TYPE 2MB8S-C Shielded RJ45 Jack to 2 x Male BNC 6" Cord.
LSA+ IDC TYPE Intended for panel mounting and can be supplied with a variety of coaxial connectors BNC, BT Type 43, 1.0/2.3, 1.6/5.6 DIN. Twisted Pair termination via 3-pole LSA+ IDC. - The mechanical endurance of the coaxial connectors are designed to provide in excess of 500 connect- - reconnect cycles. - On the balanced end, the 120Ω interface connector is designed to accept termination of single strand - conductors with nominal diameter up to 0.50mm. - The force required to terminate the IDC is designed to remain fully operative and intact after 200 - connect/reconnect cycles for LSA+ IDC Terminals. - Simple cable anchorage method integral with the balun is achieved by inserting the cable through the hollow - section under the terminal markings. MBK LSA+ IDC to Male BNC FBK LSA+ IDC to Female BNC Bulkhead W/Metal Thread. FBPK LSA+ IDC to Female BNC Bulkhead W/Plastic Isolated Thread. LSA+ IDC to Female BNC FBFK Flange Mount W/4-Hole. MTK LSA+ IDC to Male BT Type 43 Bulkhead MTFK LSA+ IDC to Male BT Type 43 Float Mount FTK LSA+ IDC to Female BT Type 43 M2DK LSA+ IDC to Male 1.0/2.3 DIN F2DK LSA+ IDC to Female 1.0/2.3 DIN
M5DK LSA+ IDC to Male 1.6/5.6 DIN F5DK LSA+ IDC to Female 1.6/5.6 DIN TOOLLESS IDC TYPE It is designed to terminate wires by hand, without punchdown tool for faster and easier installation. - Insertion loss, maximum of 0.2dB at 2Mbps and 0.3dB at 8Mbps max. - Link to data isolation, minimum 250v AC/DC min. - Transmission distance: 180m via Cat.5e cable. - Return loss, -29dB at 2Mbps and -21dB at 8Mbps. <back> MBT Toolless IDC to Male BNC FBT BNC Bulkhead W/Metal Thread. BNC Bulkhead FBPT W/Plastic Isolated Thread. FBFT BNC Flange Mount W/4-Hole. MTT Toolless IDC to Male BT Type 43 Bulkhead MTFT Toolless IDC to Male BT Type 43 Float Mount FTT BT Type 43
M2DT Toolless IDC to Male 1.0/2.3 DIN F2DT 1.0/2.3 DIN M5DT Toolless IDC to Male 1.6/5.6 DIN F5DT 1.6/5.6 DIN SCREW-IN IDC TYPE These baluns are fully shielded products which are ideal in applications where size and space are restricted due to small dimension. They are intended for panel or cable mounting and feature IDC termination allowing installation without special tools. Designed to match differential inputs and outputs or modern chipsets. - Contact: plated mini. 1.25µ Ni & mini. 1.25µ Au - IDC connect /disconnect cycle 20. - IDC suitable for 23~26 AWG cooper cable, Teflon insulators. - Body parts plated mini. 5µ Ni. - Coaxial connector insertion 500 cycle. - Cable anchorage is via a tortuous path around the stuffer cap and grounding ring. - IDC: phosphor bronze. MBI Screw-In IDC to Male BNC FBI BNC Bulkhead W/Metal Thread. BNC Bulkhead FBPI W/Plastic Isolated Thread. FBFI BNC Flange Mount W/4-Hole. MTI Screw-In IDC to Male BT Type 43 Bulkhead
Screw-In IDC to Male BT MTFI Type 43 Float Mount MTHI Screw-In IDC to Male BT Type 43 HDC Float Mount FTI BT Type 43 M2DI Screw-In IDC to Male 1.0/2.3 DIN F2DI 1.0/2.3 DIN M5DI Screw-In IDC to Male 1.6/5.6 DIN F5DI 1.6/5.6 DIN PATCH PANELS The CCITT G.703 balun panels match multiple sets of dual 75Ω coax connections to multiple 120Ω twisted-pair connections. Supporting data stream to three speed versions, 2-8 Mbps for E1/T1 and E2/T2, 2-8-34Mbps for E1/T1 to E3, 34 to 155Mbps for E3 and higher, the patch panel bi-directionally match, not only signal impedance, but also the pulse shapes of the signals according to the CCITT G.703 standard. The modular construction allows up to 16-port of G.703 balun modules in a 19" rack mount chassis. The module provides a cost-effective solution and can be purchased separately. AC power or batteries needed - Link-to-data isolation: Mini. 250V - Bi-directional signal conversion - Operating temperature: 0 C~75 C - Typical distance: 180m via Cat.5e cable - No
-HC-GP16-8FB-1U 16-Port G.703 Patch Panel, Female BNC To STP RJ45 On The Back Side. HC-GP16-8FB-2U 16-Port G.703 Patch Panel, Female BNC To STP RJ45 On The Same Side. HC-GPM01 HC-GPM02 1-Port G.703 Balun Module, Female BNC To STP RJ45 On The Back Side. 1-Port G.703 Balun Module, Female BNC To STP RJ45 On The Same Side.