SURFACE MOUNT FAST RECOVERY RECTIFIER VOLTAGE RANGE 5 to 6 Volts CURRENT.5 Ampere 5F THRU 5F5 FEATURES * Fast switching * Low leakage * Low forward voltage drop * High current capability * High currenf surge * High reliability SOD-3F MECHANICAL DATA * Epoxy: Device has UL flammability classification 94V-O * Mounting position: Any * Weight:.6 gram.35 (.9).4 (.9).6 (.7).77 (.95).8 (.7).69 (.75).8 (.).53 (.35) MAXIMUM RATINGS AND ELECTRICAL Ratings at 5 o C ambient temperature unless otherwise specified. Single phase, half wave, 6 Hz, resistive or inductive load. For capacitive load, derate current by %..3 (.75). (.55).5 (3.8).4 (3.6).47 (.) Dimensions in inches and (millimeters) MAXIMUM RATINGS (@ TA=5 O C unless otherwise noted) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 55 o C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 4) Typical Junction Capacitance (Note ) Operating and Storage Temperature Range SYMBOL V RRM V RMS V DC I O I FSM R θja R θjl CJ T J, T STG 5F 5F 5F3 5F4 5F5 UNITS 5 4 6 Volts 35 5 7 4.5 5 3 5 5-55 to + 5 8 4 Volts 4 6 Volts Amps Amps C/W pf C ELECTRICAL (@TA=5 O C unless otherwise noted) Maximum DC Reverse Current at Rated DC Blocking Voltage T A = 5 o C NOTES : Maximum Instantaneous Forward Voltage at.a DC Maximum Full Load Reverse Current Full Cycle Average,.375 (9.5mm) lead length at T L = 55 o C Maximum Reverse Recovery Time (Note ). Reverse Recovery Test Conditions: IF =.5A, IR = -.A, IRR = -.5A. Measured at MHZ and applied reverse voltage of 4. volts 3. Fully ROHS compliant, % Sn plating (Pb-free). 4. Thermal Resistance : Mounted on PCB. SYMBOL V F I R trr 5F 5F 5F3 5F4 5F5 UNITS.3 Volts 5. uamps uamps 5 5 nsec 7-7
RATING AND CURVES ( 5F THRU 5F5 ) 5 Ω NONINDUCTIVE Ω NONINDUCTIVE +.5A trr ( + ) 5 Vdc (approx) ( - ) D.U.T NON- INDUCTIVE OSCILLOSCOPE (NOTE ) ( - ) PULSE GENERATOR (NOTE ) ( + ) -.5A NOTES: Rise Time = 7ns max. Input Impedance = megohm. pf.. Rise Time = ns max. Source Impedance = 5 ohms. FIG. TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC -.A cm SET TIME BASE FOR / (ns/cm) AVERAGE FORWARD CURRENT, (A).5.4.3.. Single Phase Half Wave 6Hz Resistive or Inductive Load 5 5 75 5 5 75 INSTANTANEOUS REVERSE CURRENT, (ua) 6 4 6 4.6.4.. T A = O C T A = 5 O C 4 6 8 4 AMBIENT TEMPERATURE, ( O C) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG. TYPICAL FORWARD CURRENT DERATING CURVE FIG.3 TYPICAL REVERSE
RATING AND CURVES ( 5F THRU 5F5 ) INSTANTANEOUS FORWARD CURRENT, (A) 3...3. T J = 5 O C.3 Pulse Width=3uS % Duty Cycle..5..5..5 3. 3.5 PEAK FORWARD SURGE CURRENT, (A) 5 3 8.3ms Single Half Sine-Wave (JEDED Method) 5 5 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG.4 TYPICAL INSTANTANEOUS FORWARD NUMBER OF CYCLES AT 6Hz FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT JUNCTION CAPACITANCE, (pf) 6 4 6 4 T J = 5 O C...4. 4 4 REVERSE VOLTAGE, (V) FIG.6 TYPICAL JUNCTION CAPACITANCE
Mounting Pad Layout.3 MIN. (.75 MIN.).35MIN. (.9 MIN.).65 (4.9) REF Dimensions in inches and (millimeters)
DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.